Page 1 Pacifica 2 0 1 7 O W N E R ’ S M A N U A L...
Page 2 VEHICLES SOLD IN CANADA This manual illustrates and describes the operation of With respect to any Vehicles Sold in Canada, the name FCA features and equipment that are either standard or op- US LLC shall be deemed to be deleted and the name FCA tional on this vehicle.
Page 3 TABLE OF CONTENTS SECTION PAGE INTRODUCTION ..............3 GRAPHICAL TABLE OF CONTENTS .
Page 5: Table Of Contents
INTRODUCTION CONTENTS INTRODUCTION ......4 WARNINGS AND CAUTIONS ....6 HOW TO USE THIS MANUAL .
Page 6: Introduction
4 INTRODUCTION INTRODUCTION HOW TO USE THIS MANUAL Congratulations on selecting your new FCA US LLC ve- Essential Information hicle. Be assured that it represents precision workmanship, Consult the Table of Contents to determine which section distinctive styling, and high quality. contains the information you desire.
Page 7: Symbols
INTRODUCTION Symbols Consult the following table for a description of the symbols that may be used on your vehicle or throughout this Owner’s Manual:...
Page 8: Warnings And Cautions
6 INTRODUCTION WARNINGS AND CAUTIONS VEHICLE MODIFICATIONS/ALTERATIONS This Owner’s Manual contains WARNINGS against oper- WARNING! ating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against procedures that Any modifications or alterations to this vehicle could could result in damage to your vehicle.
Page 9 GRAPHICAL TABLE OF CONTENTS CONTENTS FRONT VIEW ......8 INSTRUMENT PANEL .....10 REAR VIEW .
Page 10 8 GRAPHICAL TABLE OF CONTENTS FRONT VIEW Front View 1 — Hood/Engine Compartment 4 — Doors 2 — Windshield 5 — Wheels/Tires 3 — Exterior Mirrors 6 — Headlights...
Page 11 GRAPHICAL TABLE OF CONTENTS 9 REAR VIEW Rear View 1 — Tail Lamps 2 — Rear Windshield Wiper 3 — Liftgate...
Page 12 10 GRAPHICAL TABLE OF CONTENTS INSTRUMENT PANEL Instrument Panel 1 — Air Vents 5 — Glove/Storage Compartment 2 — Multifunction Lever 6 — Ignition Start/Stop Button 3 — Instrument Cluster 7 — Steering Wheel 4 — Windshield Wiper Lever 8 — Headlight Switch...
Page 13 GRAPHICAL TABLE OF CONTENTS 11 INTERIOR Interior Features 1 — Power Window/Door Lock Switches 5 — Door handle 2 — Electronic Gear Selector 6 — Climate Control 3 — Uconnect Radio 7 — Center Console 4 — Switch Panel 8 — Seats...
Page 15 GETTING TO KNOW YOUR VEHICLE CONTENTS ▫ General Information .....31 KEYS ....... . .18 ▫...
Page 16 14 GETTING TO KNOW YOUR VEHICLE ▫ Hands-Free Sliding Doors – If Equipped ..45 ▫ Power Folding Third Row Head Restraints — If Equipped ......83 ▫...
Page 17 GETTING TO KNOW YOUR VEHICLE 15 ▫ Illuminated Vanity Mirrors — If Equipped ..90 ▫ Battery Protection ..... . .95 ▫...
Page 18 16 GETTING TO KNOW YOUR VEHICLE ▫ Cargo Area Features .....145 TRI-PANE PANORAMIC SUNROOF — IF EQUIPPED ......134 GARAGE DOOR OPENER —...
Page 19 GETTING TO KNOW YOUR VEHICLE 17 ROOF LUGGAGE RACK — IF EQUIPPED ..174 ▫ Deploying The Crossbars ....175 ▫ Stowing The Crossbars ....177...
Page 20: Keys
18 GETTING TO KNOW YOUR VEHICLE KEYS NOTE: The emergency key allows for entry into the vehicle should the battery in the vehicle or the key fob go Your vehicle uses a keyless ignition system. The ignition dead. The emergency key is also for locking/unlocking the system consists of a key fob with Remote Keyless Entry glove compartment.
Page 21 GETTING TO KNOW YOUR VEHICLE 19 Four Button Key Fob Five Button Key Fob...
Page 22 20 GETTING TO KNOW YOUR VEHICLE Six Button Key Fob Seven Button Key Fob To Unlock The Doors NOTE: Uconnect Settings lets you program the system to unlock either the driver’s side doors on the first push (default) or unlock all doors on the first push of the unlock button on the key fob.
Page 23 GETTING TO KNOW YOUR VEHICLE 21 1st Push Of Key Fob Unlocks Push and release the unlock button on the key fob once to unlock the driver front door and sliding door or twice within five seconds to unlock all doors and liftgate. The hazard lights will flash to acknowledge the unlock signal.
Page 24 22 GETTING TO KNOW YOUR VEHICLE Emergency Key Feature To remove the emergency key, press the mechanical button on the side of the key fob with your thumb and pull the The key fob also contains and an emergency key, which emergency key out with your other hand while pushing stores in the bottom of the key fob.
Page 25 GETTING TO KNOW YOUR VEHICLE 23 Vehicles Equipped With Keyless Enter-N-Go — Passive 1. Remove the emergency key by pushing the mechanical Entry release button on the side of the key fob with your thumb and then pull the key out with your other hand. If one or more doors are open, or the liftgate is open, the doors will lock.
Page 26 24 GETTING TO KNOW YOUR VEHICLE 2. Insert a coin, a flat blade screw driver, or the tip of your 4. Fit a new CR2032 battery ensuring that the positive (+) emergency key into the now exposed slot and carefully side is facing upwards.
Page 27 GETTING TO KNOW YOUR VEHICLE 25 Duplication of key fobs may be performed at an authorized dealer. This procedure consists of programming a blank key fob to the vehicle electronics. A blank key fob is one that has never been programmed. NOTE: When having the Sentry Key Immobilizer System serviced, bring all vehicle keys with you to an authorized dealer.
Page 28: Ignition Switch
26 GETTING TO KNOW YOUR VEHICLE The following features are always enabled when this key is NOTE: Changes or modifications not expressly approved in use: by the party responsible for compliance could void the user’s authority to operate the equipment. •...
Page 29 GETTING TO KNOW YOUR VEHICLE 27 • All the electrical devices are available. START • Start the vehicle. The engine only runs in the ON/RUN ignition position or from a remote start request. In case the ignition switch does not change with the push of a button, the key fob may have a low or dead battery.
Page 30: Steering Wheel Lock - If Equipped
28 GETTING TO KNOW YOUR VEHICLE NOTE: The key fob may not be able to be detected by the CAUTION! vehicle keyless-go system if it is located next to a mobile phone, laptop or other electronic device; these devices may An unlocked car is an invitation.
Page 31: How To Use Remote Start
GETTING TO KNOW YOUR VEHICLE 29 80° F (26.7° C), and the optional heated seats, and optional All of the following conditions must be met before the heated steering wheel in temperatures below 40° F (4.4° C). engine will remote start: •...
Page 32: To Enter Remote Start Mode
30 GETTING TO KNOW YOUR VEHICLE • The engine can be started two consecutive times (two WARNING! (Continued) 15-minute cycles) with the key fob. However, the igni- Monoxide is poisonous and can cause serious injury tion must be placed in the ON/RUN position before you or death when inhaled.
Page 33: Remote Start Comfort Systems - If Equipped
GETTING TO KNOW YOUR VEHICLE 31 Remote Start Comfort Systems — If Equipped 2. This device must accept any interference received, in- cluding interference that may cause undesired opera- When Remote Start is activated, the Climate Control, tion. vented seats (if equipped) are also activated in tempera- tures above 80°...
Page 34: Vehicle Security Alarm - If Equipped
32 GETTING TO KNOW YOUR VEHICLE indicates that someone used an invalid key fob to start the both audible and visible signals. If something triggers the engine. Either of these conditions will result in the engine alarm, the vehicle security alarm will provide the following being shut off after two seconds.
Page 35: To Disarm The System
GETTING TO KNOW YOUR VEHICLE 33 • Cycle the vehicle ignition system out of the OFF posi- 2. Perform one of the following methods to lock the vehicle: tion. • Push lock on the interior power door lock switch with •...
Page 36: Doors
34 GETTING TO KNOW YOUR VEHICLE the vehicle or not. If you remain in the vehicle and open a door, the alarm will sound. If this occurs, disarm the vehicle security alarm. If the vehicle security alarm is armed and the battery becomes disconnected, the vehicle security alarm will remain armed when the battery is reconnected;...
Page 37 GETTING TO KNOW YOUR VEHICLE 35 Manual Door Lock Rocker Switch Manual Rear Door Lock location 1 — Door Handle 2 — Manual Door Lock If the door lock button is locked (no ribbing is visible) when you shut the door, the door will lock. Therefore, make sure the key fob is not inside the vehicle before closing the door.
Page 38: Central Lock/Unlock - If Equipped
36 GETTING TO KNOW YOUR VEHICLE Central Lock/Unlock — If Equipped WARNING! A power door lock switch is on each front door trim panel. • For personal security and safety in the event of a Use this switch to lock or unlock the doors. collision, lock the vehicle doors before you drive as NOTE: The key fob may not be able to be detected by the well as when you park and leave the vehicle.
Page 39: Unlock Doors Automatically On Exit - If Equipped
GETTING TO KNOW YOUR VEHICLE 37 Unlock Doors Automatically On Exit — If Equipped The Unlock Doors Automatically On Exit feature unlocks all of the vehicle doors when any door is opened. This will occur only after the gear selector has been placed into the PARK position, after the vehicle has been driven (the gear selector has been placed out of PARK and all doors closed).
Page 40 38 GETTING TO KNOW YOUR VEHICLE NOTE: To Unlock From The Driver’s Side: • Passive Entry may be programmed ON/OFF. Refer to With a valid key fob within 5 ft (1.5 m) of the driver’s door “Uconnect Settings” in “Multimedia” for further infor- handle, grab the driver’s front door handle to unlock the mation.
Page 41 GETTING TO KNOW YOUR VEHICLE 39 • A lock request is made by the door panel switch while To Unlock From The Passenger Side: the door is open. With a valid key fob within 5 ft (1.5 m) of the passenger door handle, grab the front passenger door handle to When any of these situations occur, after all open doors are unlock all four doors and the liftgate automatically.
Page 42 40 GETTING TO KNOW YOUR VEHICLE To Enter The Liftgate To Lock The Vehicle’s Doors With a valid key fob within 5 ft (1.5 m) of the liftgate, cycle With one of the vehicle’s key fobs within 5 ft (1.5 m) of the the handle to open the liftgate and pull the liftgate open driver or passenger front door handle, push the door with one fluid motion.
Page 43: Manual Sliding Side Door
GETTING TO KNOW YOUR VEHICLE 41 Do NOT grab the door handle, when pushing the door The vehicle doors can also be locked by using the key fob handle button. This could unlock the door(s). lock button, or the lock button located on the vehicle’s interior door panel.
Page 44: Power Sliding Side Door - If Equipped
42 GETTING TO KNOW YOUR VEHICLE • There is a hold-open latch that is activated when the sliding door is fully opened. This latch will keep your sliding door open on any incline. To close the sliding door after the hold-open latch is activated, you must rock the inside handle forward or pull outward on the exterior handle.
Page 45 GETTING TO KNOW YOUR VEHICLE 43 The key fob and the overhead console button will operate when the handles are manual. When the LED is lit, pushing the door when the door is locked. All other ways require the power sliding door power off button will return the the sliding door to be unlocked.
Page 46 44 GETTING TO KNOW YOUR VEHICLE WARNING! Personal injury or cargo damage may occur if caught in the path of the sliding door. Make sure the door path is clear before closing the door. WARNING! Before driving off, check the instrument cluster for a sliding door or door open message or warning indica- tor.
Page 47: Getting To Know Your Vehicle 45
GETTING TO KNOW YOUR VEHICLE 45 Hands-Free Sliding Doors – If Equipped NOTE: • To open the Hands-Free Sliding Doors requires a valid Passive Entry key fob within 5 ft (1.5 m) of the door handle. If a valid Passive Entry key fob is not within 5 ft (1.5 m), the door will not respond to any kicks.
Page 48: Safe Lock - If Equipped
46 GETTING TO KNOW YOUR VEHICLE Safe Lock — If Equipped To provide a safer environment for small children riding in the rear seats, the second row sliding door switches may be overridden by pushing the Sliding Doors Power OFF button, located in the front overhead console.
Page 49: Child Locks
GETTING TO KNOW YOUR VEHICLE 47 Child Locks NOTE: • After engaging (or disengaging) the Child Protection To provide a safer environment for small children riding in Door Lock, always test the inside door handle with the the rear seats, the sliding doors are equipped with a Child sliding door closed to make certain the Child Protection Protection Door Lock system.
Page 50: Seats
48 GETTING TO KNOW YOUR VEHICLE To Disengage The Child Protection Door Lock WARNING! (Continued) 1. Open the sliding side door. these areas are more likely to be seriously injured or killed. 2. Slide the Child Protection Door Lock control outward •...
Page 51 GETTING TO KNOW YOUR VEHICLE 49 Manual Front Adjuster While sitting in the seat, pull up on the handle and slide the seat forward or rearward. Release the bar once you have Both front seats are adjustable forward or rearward. The reached the desired position.
Page 52 50 GETTING TO KNOW YOUR VEHICLE Manual Reclining Seats — If Equipped WARNING! For models equipped with manual seats, the recline lever is Do not ride with the seatback reclined so that the located on the outboard side of the seat. shoulder belt is no longer resting against your chest.
Page 53: Manual Adjustment (Rear Seats)
GETTING TO KNOW YOUR VEHICLE 51 Manual Adjustment (Rear Seats) WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be adjusted properly and you could be injured.
Page 54 52 GETTING TO KNOW YOUR VEHICLE Manual Recline WARNING! To recline, lean forward slightly, lift the lever, and push Do not ride with the seatback reclined so that the back to the desired position and release the lever. Lean shoulder belt is no longer resting against your chest. In forward and lift the lever to return the seatback to its a collision you could slide under the seat belt, which normal position.
Page 55 GETTING TO KNOW YOUR VEHICLE 53 NOTE: Easy Entry • The seatback may lock into the fold flat position. Use the Easy Tilt Seat — With Or Without Child Seat Installed recline lever to unlock the seatback. The 2nd row seats can be tilted forward for easy entry into •...
Page 56 54 GETTING TO KNOW YOUR VEHICLE Easy Entry — With The Seat Folded Flat The seats can be folded and tilted for more accessibility for passengers to enter and exit the third row. 1. Without a child seat installed, you can fold the seat by pulling the recliner handle on the bottom part of the seat.
Page 57 GETTING TO KNOW YOUR VEHICLE 55 Pull the strap on the back of the seat and the seat will tilt Exit For 3rd Row Passengers forward. For passengers seated in the third row, there is a pull strap located on the outboard side of the seat near the bottom of the seat back.
Page 58 56 GETTING TO KNOW YOUR VEHICLE Stow ’n Go Seating On vehicles equipped with Stow ’n Go seating, the second and third row seats can be folded into the floor for convenient storage. Stow ‘n Go Assist — If Equipped On vehicles equipped with the Stow ‘n Go Assist feature, the front seat will move forward automatically to a location that will allow the second row Stow ‘n Go seat movement,...
Page 59 GETTING TO KNOW YOUR VEHICLE 57 • If the front seat is already in a location that will allow 1. Push and release the Stow ‘n Go Assist button. The front seat cushion and seat back will move as necessary to a space for Stow ‘n Go of the second row seat, the front location that will allow space for the second row Stow ‘n seat will not move and a message will be displayed in...
Page 60 58 GETTING TO KNOW YOUR VEHICLE • For information on storage bin function with the seats For Power Seats: Push the Stow ‘n Go Assist button located on the B pillar trim (if equipped.) Refer to Stow ’n Go rearward refer to “Second Row Floor Storage Bins” in Assist - If Equipped in this section for instructions.
Page 61 GETTING TO KNOW YOUR VEHICLE 59 3. Pull the floor panel and position it toward the front seats 4. Fold the armrest upward and stow the seat by grabbing while folding the top half down and rest it against the the strap on the lower part of the back seat and guide front seats.
Page 62 60 GETTING TO KNOW YOUR VEHICLE 5. Push down on the seat back to lock the seat in the tub. 6. Close the floor by pulling the floor panel backwards by the bottom corner edge of the panel. Push To Lock Extend Floor Panel...
Page 63 GETTING TO KNOW YOUR VEHICLE 61 7. Push down on floor panel to lock into place. WARNING! In a collision, serious injury could result if the seat storage bin covers are not properly latched: • Do not drive the vehicle with the storage bin covers open.
Page 64 62 GETTING TO KNOW YOUR VEHICLE To Unstow Second Row Seats NOTE: • Push the lock rod inward for the locked position. For Manual Seats: To unstow the seat from the floor, move the front seat all the way forward using the manual seat •...
Page 65 GETTING TO KNOW YOUR VEHICLE 63 3. Pull the floor panel and position it toward the front seats 4. Pull the strap located on the seat and pull the seat out of while folding the top half down and rest it against the the storage bin.
Page 66 64 GETTING TO KNOW YOUR VEHICLE 5. To position the floor panel back into its original state, grab the bottom corner and extend it outward. Push Down To lock 7. Readjust the front seat as needed. Extend Panel WARNING! 6. Lay the floor panel flat and push down until it clicks into position.
Page 67 GETTING TO KNOW YOUR VEHICLE 65 The release strap is located on the front of the seat, near the WARNING! (Continued) floor. To remove the seat, pull the release strap to release their upright positions when the seat is to be occu- the rear latches.
Page 68 66 GETTING TO KNOW YOUR VEHICLE To reinstall the seat, align the seat into the detent positions Manually Folding Third Row Seats — If Equipped on the floor. Tilt seat rearward to lock the seat back into its 1. Lower the center head restraint down to the seatback by original position.
Page 69 GETTING TO KNOW YOUR VEHICLE 67 3. Pull release strap marked “2” and tumble the seat rearward into the storage bin. Stowed Third Row Seat Strap “2”...
Page 70 68 GETTING TO KNOW YOUR VEHICLE To Unfold Third Row Seats 1. Pull up on the assist strap to lift the seat out of the storage bin and push the seat forward until the anchors latch. Strap “2” 3. Raise the head restraint to its upright position. WARNING! •...
Page 71: Power Adjustment (Front Seats) - If Equipped
GETTING TO KNOW YOUR VEHICLE 69 Power Adjustment (Front Seats) — If Equipped WARNING! Some models may be equipped with eight-way power • Adjusting a seat while driving may be dangerous. seats for the driver and front passenger. The power seat Moving a seat while driving could result in loss of switches are located on the outboard side of the seat.
Page 72 70 GETTING TO KNOW YOUR VEHICLE move in the direction of the switch. Release the switch WARNING! when the desired position has been reached. • Adjusting a seat while driving may be dangerous. Adjusting The Seat Up Or Down Moving a seat while driving could result in loss of The height of the seats can be adjusted up or down.
Page 73: Power Adjustment (Rear Seats) - If Equipped
GETTING TO KNOW YOUR VEHICLE 71 Power Lumbar — If Equipped WARNING! (Continued) Vehicles equipped with power driver or passenger seats • Do not place the seat belt webbing behind the third may be equipped with power lumbar. The power lumbar row stow clip when using the seat belt to restrain an switch is located on the outboard side of the power seat.
Page 74 72 GETTING TO KNOW YOUR VEHICLE Reclining The Seatback NOTE: The third row outboard seat belts may interfere with the power folding of the seat. Place the seat belt The angle of the seatback can be adjusted forward or webbing behind the stow clip before stowing or opening rearward.
Page 75 GETTING TO KNOW YOUR VEHICLE 73 Left and right third row seats can be folded individually or To move the selected seat(s) to the stow position, push and together. The third row power folding seat adjusts to the release the Stow button. The seat will automatically stop following positions using the switch bank located on the when the Stow position is reached.
Page 76: Driver Memory Seat - If Equipped
74 GETTING TO KNOW YOUR VEHICLE Driver Memory Seat — If Equipped The Memory Buttons (1) and (2) on the driver’s door panel can be programmed to recall the driver’s seat, outside mirrors, and radio station preset settings. Your key fobs can also be programmed to recall the same positions when the unlock button is pushed.
Page 77 GETTING TO KNOW YOUR VEHICLE 75 Programming The Memory Feature Linking And Unlinking The Remote Keyless Entry Key Fob To Memory To create a new memory profile, perform the following: Your key fob can be programmed to recall one of two 1.
Page 78 76 GETTING TO KNOW YOUR VEHICLE 5. Push and release the lock button on the key fob within NOTE: Pushing the mirror adjust switch will cancel the 10 seconds. memory mirror recall. NOTE: Your key fob can be unlinked to your memory Easy Entry/Exit Seat (Available With Memory Seat settings by pushing the set (S) button, and within 10 Only)
Page 79: Heated Seats - If Equipped
GETTING TO KNOW YOUR VEHICLE 77 • The Easy Entry/Easy Exit feature is disabled when the • Press the heated seat button a second time to turn driver seat position is less than 0.9 inches (22.7 mm) the LO setting ON. forward of the rear stop.
Page 80 78 GETTING TO KNOW YOUR VEHICLE WARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater.
Page 81: Ventilated Seats - If Equipped
GETTING TO KNOW YOUR VEHICLE 79 • Press the ventilated seat button operation. Then, the heat output will drop to the normal a third time to turn HI-level. If the HI-level setting is selected, the system will the ventilated seat OFF. automatically switch to LO-level after approximately 60 NOTE: The engine must be running for the ventilated seats minutes of continuous operation.
Page 82: Head Restraints
80 GETTING TO KNOW YOUR VEHICLE HEAD RESTRAINTS Head Restraints — Front Seats Head restraints are designed to reduce the risk of injury by The front driver and passenger seats are equipped with restricting head movement in the event of a rear impact. four-way head restraints.
Page 83 GETTING TO KNOW YOUR VEHICLE 81 Front Head Restraint Normal Position 1 — Adjustment Button 2 — Release Button...
Page 84: Head Restraints - Second Row
82 GETTING TO KNOW YOUR VEHICLE Head Restraints — Second Row The second row outboard head restraints are non- adjustable. The removable 8th passenger seat (if equipped) has an adjustable head restraint. Head Restraints — Third Row The outboard head restraints can be manually folded forward for improved visibility while in REVERSE.
Page 85: Power Folding Third Row Head Restraints - If Equipped
GETTING TO KNOW YOUR VEHICLE 83 NOTE: • The head restraints must be raised manually when occupying the third row. • Do not fold if there are passengers seated in the third row seats. The head restraint in the center position can be raised and lowered for tether routing or height adjustment.
Page 86: Steering Wheel
84 GETTING TO KNOW YOUR VEHICLE NOTE: • The head restraints can be folded downward using the Head Restraint button or using the manual release strap. The head restraints must be raised manually when occupying the third row. • Do not fold if there are passengers seated in the third row seats.
Page 87: Heated Steering Wheel - If Equipped
GETTING TO KNOW YOUR VEHICLE 85 • Press the heated steering wheel button a second time WARNING! to turn the heating element off. Do not adjust the steering column while driving. NOTE: The engine must be running for the heated steering Adjusting the steering column while driving or driv- wheel to operate.
Page 88: Mirrors
86 GETTING TO KNOW YOUR VEHICLE MIRRORS Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from Inside Day/Night Mirror — If Equipped vehicles behind you. You can turn the feature on or off by A single ball joint mirror is used to allow the driver to pushing the button at the base of the mirror.
Page 89: Outside Mirrors
GETTING TO KNOW YOUR VEHICLE 87 Driver’s Outside Automatic Dimming Mirror — If CAUTION! Equipped To avoid damage to the mirror during cleaning, never The driver’s outside mirror will automatically adjust for spray any cleaning solution directly onto the mirror. glare from vehicles behind you.
Page 90: Power Mirrors - If Equipped
88 GETTING TO KNOW YOUR VEHICLE Power Mirrors — If Equipped Left and Right side power mirror preselected positions can be controlled by the optional Driver Memory Seat Feature. The power mirror controls are located on the driver-side Refer to “Driver Memory Seat” in “Seats” for further door trim panel.
Page 91: Power Folding Mirrors - If Equipped
GETTING TO KNOW YOUR VEHICLE 89 NOTE: The Tilt Side Mirrors In Reverse feature is not NOTE: If the vehicle speed is greater than 10 mph enabled when delivered from the factory. The Tilt Side (16 km/h), the folding feature will be disabled. Mirrors In Reverse feature can be enabled or disabled in If the mirrors are in the folded position, and vehicle speed the instrument cluster display.
Page 92: Illuminated Vanity Mirrors - If Equipped
90 GETTING TO KNOW YOUR VEHICLE Illuminated Vanity Mirrors — If Equipped Conversation Mirror An illuminated vanity mirror is located on the sun visor. To Located in the overhead console there is a conversation use the mirror, rotate the sun visor down and swing the mirror to view all the passengers in the vehicle.
Page 93: Exterior Lights
GETTING TO KNOW YOUR VEHICLE 91 EXTERIOR LIGHTS Rotate the headlight switch clockwise to the second detent for parking light and instrument panel light operation. Headlight Switch Rotate the headlight switch to the third detent for head- The headlight switch is located on the left side of the light, parking light and instrument panel operation.
Page 94: Headlights On With Wipers - If Equipped
92 GETTING TO KNOW YOUR VEHICLE Headlights On With Wipers — If Equipped Refer to “Uconnect Settings” in “Multimedia” for further information. When your headlights are in the AUTO mode and the engine is running, the headlights will automatically turn If the headlights are turned off before the ignition, they will on when the wiper system is also turned on.
Page 95: Front Fog Lights - If Equipped
GETTING TO KNOW YOUR VEHICLE 93 Front Fog Lights — If Equipped Multifunction Lever To activate the front fog lights, turn on the parking lights or The multifunction lever is located on the left side of the the low beam headlights and push in the headlight switch steering column.
Page 96: Turn Signals
94 GETTING TO KNOW YOUR VEHICLE Turn Signals low beams to high beams. Pulling back to the neutral position returns the headlights to the low beam operation. Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper Flash-To-Pass operation of the front and rear turn signal lights.
Page 97: Battery Protection
GETTING TO KNOW YOUR VEHICLE 95 To Activate 3. Rotate the headlight switch counterclockwise from the AUTO to the on position. 1. Select “Automatic High Beams — ON” through the Uconnect system. Refer to Uconnect Settings” in “Mul- NOTE: Once active, the Automatic High Beam system will timedia”...
Page 98 96 GETTING TO KNOW YOUR VEHICLE Rear Courtesy/Reading Lights — If Equipped Located above the rear passengers are courtesy/reading lights. The lights turn on when a front door, a sliding door or the liftgate is opened. If your vehicle is equipped with remote keyless entry the lights will also turn on when the unlock button on the key fob is pushed.
Page 99: Instrument Panel Dimmer Control
GETTING TO KNOW YOUR VEHICLE 97 Instrument Panel Dimmer Control The instrument panel dimmer control is part of the head- light switch, and is located on the driver’s side of the instrument panel. With the parking lights or headlights on, rotate the instru- ment panel dimmer control upward or downward to increase or decrease the brightness of the instrument panel.
Page 100: Windshield Wiper And Washers
98 GETTING TO KNOW YOUR VEHICLE Ambient Light Control — If Equipped Parade Mode (Daytime Brightness Feature) Rotate the ambient dimmer control upward or downward Rotate the instrument panel dimmer control upward to the to increase or decrease the brightness of the ambient light first detent.
Page 101: Intermittent Wiper System
GETTING TO KNOW YOUR VEHICLE 99 NOTE: Always remove any buildup of snow that prevents Windshield Wiper Operation the windshield wiper blades from returning to the off Rotate the end of the lever upward, to the first detent past position. If the windshield wiper switch is turned off and the intermittent settings for low-speed wiper operation.
Page 102: Rain Sensing Wipers - If Equipped
100 GETTING TO KNOW YOUR VEHICLE • Use of Rain-X or products containing wax or silicone Rain Sensing Wipers — If Equipped may reduce rain sensor performance. This feature senses moisture on the windshield and auto- • The Rain Sensing feature can be turned on and off matically activates the wipers for the driver.
Page 103: Rear Wiper And Washer
GETTING TO KNOW YOUR VEHICLE 101 • Remote Start Mode Inhibit — On vehicles equipped Rear Windshield Washer Operation with Remote Starting system, Rain Sensing wipers are Pushing the windshield wiper lever forward activates the not operational when the vehicle is in the remote start rear window washer.
Page 104: Climate Controls
102 GETTING TO KNOW YOUR VEHICLE CLIMATE CONTROLS Manual Climate Controls Overview Uconnect 8.4/8.4 NAV Manual Climate Controls...
Page 105 GETTING TO KNOW YOUR VEHICLE 103 Manual Climate Control Descriptions Icon Description MAX A/C Button Press and release to change the current setting, the indicator illuminates when MAX A/C is ON. Performing this function again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off.
Page 106 104 GETTING TO KNOW YOUR VEHICLE Icon Description Front Defrost Button Press and release to change the current airflow setting to Defrost mode. The indicator illumi- nates when this feature is ON. Air comes from the windshield and side window demist outlets. When the defrost button is selected, the blower level will increase.
Page 107 GETTING TO KNOW YOUR VEHICLE 105 Icon Description SYNC Button Press the Sync button on the touchscreen to toggle the Sync feature On/Off. The Sync indicator is illuminated when this feature is enabled. Sync is used to synchronize the passenger tempera- ture setting with the driver temperature setting.
Page 108 106 GETTING TO KNOW YOUR VEHICLE Icon Description Modes Control Push the button in the center of the knob to change the airflow distribution mode. The airflow distribution mode can be adjusted so air comes from the instrument panel outlets, floor outlets, defrost outlets and demist outlets.
Page 109 GETTING TO KNOW YOUR VEHICLE 107 Icon Description Mix Mode Mix Mode Air is directed through the floor, defrost, and side window demister outlets. This setting works best in cold or snowy conditions that require extra heat to the windshield. This setting is good for maintaining comfort while reducing moisture on the windshield.
Page 110 108 GETTING TO KNOW YOUR VEHICLE • To return to the Front screen on the Uconnect radio, press the Front Climate button on the touchscreen. Uconnect 5.0 Front MTC Panel Rear Control Display Icon Description Rear Lock Button Press and release to lock out the rear manual temperature controls from adjusting the rear tem- perature and blower settings.
Page 111 GETTING TO KNOW YOUR VEHICLE 109 Icon Description Rear Passenger Temperature Up and Down Buttons Provides the rear passengers with independent temperature control. Push the up arrow button on the touchscreen to increase the temperature. Push the down arrow button on the touchscreen to decrease the temperature.
Page 112 110 GETTING TO KNOW YOUR VEHICLE Icon Description Panel Mode Panel Mode Press this button on the touchscreen to change the air distribution mode to Panel Mode. In Panel Mode, air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air.
Page 113 GETTING TO KNOW YOUR VEHICLE 111 Rear Manual Temperature Control The rear MTC system has floor air outlets at the rear right side of the 3rd Row seats and overhead outlets at each outboard rear seating position. The system provides heated air through the floor outlets or cool, dehumidified air through the headliner outlets.
Page 114 112 GETTING TO KNOW YOUR VEHICLE Icon Description Bi-Level Mode Bi-Level Mode Air comes from both the headliner outlets and the floor outlets. NOTE: In many temperature positions, the Bi-Level mode is designed to provide cooler air out of the headliner outlets and warmer air from the floor outlets. Floor Mode Floor Mode Air comes from the floor outlets.
Page 115 GETTING TO KNOW YOUR VEHICLE 113 Icon Description Rear Climate Control/Blower Off To manually set the rear blower controls to off, press the Rear Climate Control/Blower Off button. CAUTION! Interior air enters the Rear Automatic Temperature Control System through an intake grille, located in floor under the passengers’...
Page 116: Automatic Climate Controls Overview
114 GETTING TO KNOW YOUR VEHICLE Automatic Climate Controls Overview Uconnect 5.0 Automatic Climate Controls...
Page 117 GETTING TO KNOW YOUR VEHICLE 115 Uconnect 8.4/8.4 NAV Automatic Climate Controls Automatic Climate Control Descriptions Icon Description MAX A/C Button Press and release to change the current setting, the indicator illuminates when MAX A/C is ON. Performing this function again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off.
Page 118 116 GETTING TO KNOW YOUR VEHICLE Icon Description A/C Button Press and release to change the current setting, the indicator illuminates when A/C is ON. Recirculation Button Press and release this button to change the system between recirculation mode and outside air mode.
Page 119 GETTING TO KNOW YOUR VEHICLE 117 Icon Description Front Defrost Button Press and release to change the current airflow setting to Defrost mode. The indicator illumi- nates when this feature is ON. Air comes from the windshield and side window demist outlets. When the defrost button is selected, the blower level may increase.
Page 120 118 GETTING TO KNOW YOUR VEHICLE Icon Description SYNC Button Press the Sync button on the touchscreen to toggle the Sync feature On/Off. The Sync indicator is illuminated when this feature is enabled. Sync is used to synchronize the passenger tempera- ture setting with the driver temperature setting.
Page 121 GETTING TO KNOW YOUR VEHICLE 119 Icon Description Panel Mode Panel Mode Air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air. The air vanes of the center outlets and outboard outlets can be moved up and down or side to side to regulate airflow direction.
Page 122 120 GETTING TO KNOW YOUR VEHICLE Icon Description Climate Control OFF Button Press and release this button to turn the Climate Control ON/OFF. Controlling The Rear Climate Controls From The CAUTION! Front ATC Panel Failure to follow these cautions can cause damage to The Three-Zone ATC system allows for adjustment of the the heating elements: rear climate controls from the front ATC panel.
Page 123 GETTING TO KNOW YOUR VEHICLE 121 • To return to the Front screen on the Uconnect radio, press the Front Climate or “Done” button on the touchscreen. Uconnect 8.4 Front ATC Panel Rear Control Display Uconnect 5.0 Front ATC Panel Rear Control Display Icon Description Rear Auto Button...
Page 124 122 GETTING TO KNOW YOUR VEHICLE Icon Description Front Climate Button/Done Press and release this button to change the display on the Uconnect radio back to the Front Cli- mate Controls. Done Rear Passenger Temperature Up and Down Buttons Provides the rear passengers with independent temperature control. Push the up arrow button on the touchscreen to increase the temperature.
Page 125 GETTING TO KNOW YOUR VEHICLE 123 Icon Description Rear Passenger Climate Control OFF Button Press and release this button to turn the Rear Climate Controls off. Panel Mode Panel Mode Press this button on the touchscreen to change the air distribution mode to Panel Mode. In Panel Mode, air comes from the outlets in the instrument panel.
Page 126 124 GETTING TO KNOW YOUR VEHICLE Rear Automatic Temperature Control (ATC) — If Equipped The rear ATC system has floor air outlets underneath the passengers’ seats, and overhead outlets at each outboard rear seating position. The system provides heated air through the floor outlets or cool, dehumidified air through the headliner outlets.
Page 127 GETTING TO KNOW YOUR VEHICLE 125 NOTE: • It is not necessary to move the temperature settings. The system automatically adjusts the temperature, mode and fan speed to provide comfort as quickly as possible. Icon Description Rear Mode Control Push this button on the Rear Climate Hard Controls to change the air distribution mode for the rear passengers to one of the following: Panel Mode Panel Mode...
Page 128 126 GETTING TO KNOW YOUR VEHICLE Icon Description Rear Temperature Control • Rear Passenger Temperature Up Button To change the temperature in the rear of the vehicle, push temperature control up button to raise the temperature. The rear temperature settings are displayed in control head.
Page 129: Climate Control Functions
GETTING TO KNOW YOUR VEHICLE 127 Climate Control Functions Recirculation When outside air contains smoke, odors, or high humidity, Air Conditioning (A/C) or if rapid cooling is desired, you may wish to recirculate The Air Conditioning (A/C) button allows the operator to interior air by pressing the Recirculation control button.
Page 130: Operating Tips
128 GETTING TO KNOW YOUR VEHICLE 2. Next, adjust the temperature you would like the system Manual Operation Override to maintain by adjusting the driver and passenger This system offers a full complement of manual override temperature control buttons. Once the desired tempera- features.
Page 131 GETTING TO KNOW YOUR VEHICLE 129 properly and the proper amount, type, and concentration Outside Air Intake of coolant is used. Refer to “Dealer Service” in “Servicing Make sure the air intake, located directly in front of the And Maintenance” for proper coolant selection. Use of the windshield, is free of obstructions such as leaves.
Page 132 130 GETTING TO KNOW YOUR VEHICLE Operating Tips Chart...
Page 133: Windows
GETTING TO KNOW YOUR VEHICLE 131 WINDOWS Power Windows You can control either the front or rear windows using controls located on the driver’s door trim panel. The driver may lock out the rear power windows by pushing the bar control just below the power window controls.
Page 134 132 GETTING TO KNOW YOUR VEHICLE Auto Up Feature With Anti-Pinch Protection — If Equipped The front driver and front passenger controls may be equipped with an Auto Up feature. Lift the window control fully upward to the second detent, release, and the window will go up automatically.
Page 135 GETTING TO KNOW YOUR VEHICLE 133 The controls will operate only when the ignition switch is WARNING! in the ON/RUN or ACC position and during power accessory delay. There is no anti-pinch protection when the window is almost closed. To avoid personal injury be sure to clear NOTE: The controls will not operate if the driver has your arms, hands, fingers and all objects from the activated the Power Window Lockout.
Page 136: Tri-Pane Panoramic Sunroof - If Equipped
134 GETTING TO KNOW YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.
Page 137: Opening Sunroof
GETTING TO KNOW YOUR VEHICLE 135 NOTE: If the sunshade is in the closed position when the WARNING! (Continued) open switch is pushed, the sunshade will automatically ON/RUN mode. Occupants, particularly unattended cycle to the halfway open position prior to the sunroof children, can become entrapped by the power sun- opening.
Page 138: Closing Sunroof
136 GETTING TO KNOW YOUR VEHICLE Closing Sunroof Power Sun Shade — If Equipped Express Mode Opening Power Shade — Express Mode Push the switch forward and release it within one second Push the shade switch rearward and release it within one and the sunroof will close automatically from any position.
Page 139: Pinch Protect Feature
GETTING TO KNOW YOUR VEHICLE 137 and stop automatically. This is called “Express Close”. Sunroof Maintenance During Express Close operation, any other actuation of the Use only a non-abrasive cleaner and a soft cloth to clean the switch will stop the shade. glass panel.
Page 140 138 GETTING TO KNOW YOUR VEHICLE Hood Release Lever Safety Latch Release Lever Location 2. Move to the outside of the front of the vehicle. 4. Remove the support rod from the locking tab and insert it into the seat located on the underside of the hood. 3.
Page 141: Closing
GETTING TO KNOW YOUR VEHICLE 139 Closing LIFTGATE 1. Hold up the hood with one hand and with the other Opening hand remove the support rod from its seat and reinsert To Unlock/Enter The Liftgate it into the locking tab. The liftgate may be released in several ways: 2.
Page 142: Closing
140 GETTING TO KNOW YOUR VEHICLE The key fob and the overhead console button will release Closing the liftgate when the liftgate is locked. The outside handle To Close The Liftgate requires the liftgate to be unlocked. If the vehicle is Grasp the liftgate closing handle and initiate lowering the equipped with Passive Entry, pulling the outside handle liftgate.
Page 143: Power Liftgate - If Equipped
GETTING TO KNOW YOUR VEHICLE 141 Power Liftgate — If Equipped The power liftgate may be opened or closed in several ways: • Overhead console liftgate button • Key fob • Outside handle (opens liftgate only) • Button just inside the liftgate on the upper left trim (when liftgate is open) •...
Page 144 142 GETTING TO KNOW YOUR VEHICLE (if equipped) will unlock and open the liftgate, with a valid To Close The Liftgate Passive Entry key fob within 5 ft (1.5 m) of the liftgate The liftgate can also be closed using the Rear Interior handle.
Page 145: Hands-Free Liftgate - If Equipped
GETTING TO KNOW YOUR VEHICLE 143 Hands-Free Liftgate — If Equipped Vehicles Equipped With A Trailer Tow Package NOTE: If your vehicle is equipped with the Trailer Tow Package, the hands-free activation zone(s) for the Power Liftgate will be located on the left and right side of the receiver.
Page 146 “Multimedia” Owner’s Manual opening the liftgate. www.chrysler.com/en/owners/manuals for further infor- mation. The Hands-Free Liftgate feature should be turned • If the liftgate is left open for an extended period of time, off during Jacking, Tire Changing, and Vehicle Service. the liftgate may need to be closed manually to reset power liftgate functionality.
Page 147: Cargo Area Features
GETTING TO KNOW YOUR VEHICLE 145 Gas props support the liftgate in the open position. How- ever, because the gas pressure drops with temperature, it may be necessary to assist the props when opening the liftgate in cold weather. NOTE: Allow the power system to open the liftgate. Manually pushing or pulling the liftgate may activate the liftgate obstacle detection feature and stop the power operation or reverse its direction.
Page 148 146 GETTING TO KNOW YOUR VEHICLE IMPORTANT SAFETY INSTRUCTIONS WARNING! Read all instructions before using. When using your To reduce the risk of fire, serious injury or death: vacuum, basic precautions should be followed, including • Do not use vacuum while vehicle is in motion or the following: while driving.
Page 149 GETTING TO KNOW YOUR VEHICLE 147 1. Before Using Vacuum: WARNING! (Continued) Accessory (ACC) Mode Operation - For up to 10 minutes • Do not put any object into openings. Do not use with of operation any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.
Page 150 148 GETTING TO KNOW YOUR VEHICLE WARNING! Carbon monoxide (CO) in exhaust gases can cause serious injury or death. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. • Do not start or run an engine in a closed garage or confined area.
Page 151 GETTING TO KNOW YOUR VEHICLE 149 • Hose Extension — Use to add another 12 ft of usable length to the vacuum hose. Hose extension is located in the upper access panel behind the third row seat on the driver’s side. 4.
Page 152 150 GETTING TO KNOW YOUR VEHICLE WARNING! WARNING! (Continued) • Do not put any object into openings. Do not use with For in vehicle use ONLY. To reduce the risk of fire, serious injury or death: any opening blocked; keep free of dust, lint, hair, •...
Page 153 GETTING TO KNOW YOUR VEHICLE 151 5. When finished, push power button to turn vacuum off stale odors, allow both to dry completely before rein- and store vacuum hose and any attachments. stalling in your vehicle. If filter has tears, holes or other damage and needs to be replaced, please contact your 6.
Page 154 152 GETTING TO KNOW YOUR VEHICLE Hose Access Port The hose access port is located behind the upper access panel behind the third row seat on the driver’s side. To Remove Vacuum Hose For Cleaning Debris Bin Release Knob 4. Remove the filter and dump the debris in a trash can. Lightly tap the filter on the collection bin to remove loose debris from the filter.
Page 155: Garage Door Opener - If Equipped
GETTING TO KNOW YOUR VEHICLE 153 2. Return to vacuum nozzle storage location located be- The HomeLink buttons, located on the driver’s sunvisor, hind the sliding door. designate the three different HomeLink channels. The HomeLink indicator is located above the center button. 3.
Page 156: Before You Begin Programming Homelink
154 GETTING TO KNOW YOUR VEHICLE Before You Begin Programming HomeLink Programming A Rolling Code For programming garage door openers that were manufac- Be sure that your vehicle is parked outside of the garage tured after 1995. These garage door openers can be identi- before you begin programming.
Page 157 GETTING TO KNOW YOUR VEHICLE 155 1. Place the ignition in the ON/RUN position. 6. Return to the vehicle and push the programmed HomeLink button twice (holding the button for two 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) seconds each time).
Page 158: Canadian/Gate Operator Programming
156 GETTING TO KNOW YOUR VEHICLE • To program the two remaining HomeLink buttons, Programming A Non-Rolling Code repeat each step for each remaining button. DO NOT For programming Garage Door Openers manufactured erase the channels. before 1995. Reprogramming A Single HomeLink Button (Non- 1.
Page 159 GETTING TO KNOW YOUR VEHICLE 157 the signal during programming. Similar to this Canadian NOTE: law, some U.S. gate operators are designed to time-out in • If the indicator light stays on constantly, programming the same manner. is complete and the garage door/device should acti- vate when the HomeLink button is pushed.
Page 160: Using Homelink
158 GETTING TO KNOW YOUR VEHICLE • Push the LEARN button on the Garage Door Opener to Using HomeLink complete the training for a Rolling Code. To operate, push and release the programmed HomeLink • Did you unplug the device for programming and re- button.
Page 161: General Information
GETTING TO KNOW YOUR VEHICLE 159 INTERNAL EQUIPMENT WARNING! (Continued) Storage use a garage door opener without these safety fea- tures. Call toll-free 1-800-355-3515 or, on the Internet Glove Compartment at HomeLink.com for safety information or assis- The glove compartment is located on the passenger side of tance.
Page 162 160 GETTING TO KNOW YOUR VEHICLE Front Door Storage Instrument Panel Drawer Both interior front door panels have multiple pockets for There is a storage drawer located in the lower center of the storage. instrument panel. It can be released by pushing the access button above it.
Page 163 GETTING TO KNOW YOUR VEHICLE 161 Drawer Released Drawer Fully Open CAUTION! The storage drawer must be closed while driving. If left open during a collision, additional damage may occur to property or the drawer mechanism.
Page 164 162 GETTING TO KNOW YOUR VEHICLE Front Seatback Storage — If Equipped Umbrella Holder The front seatbacks have a storage pocket on some models. An umbrella holder has been conveniently molded into the front door entry scuff moldings. Front Seatback Storage Umbrella Holder...
Page 165 GETTING TO KNOW YOUR VEHICLE 163 Second Row Floor Storage Bins 1. To access the storage bin with front seats in the rearward position, place the lock rod in the unlocked position so The area below the load floor, located in front of the second the load floor can fold upwards towards the seatback.
Page 166 164 GETTING TO KNOW YOUR VEHICLE 2. Pull the latch located near the second row seat to open WARNING! (Continued) the floor panel. • Do not operate the storage bin covers while the vehicle is in motion. • Do not use a storage bin latch as a tie down. CAUTION! The storage bin cover must lay flat and be locked to avoid damage from contact with the front seat tracks,...
Page 167 GETTING TO KNOW YOUR VEHICLE 165 Seat Storage Bin Cover Emergency Release Lever WARNING! (Continued) As a security measure, the Seat Storage Bin Cover has an children may not be able to escape. If trapped in the Emergency Release Lever built into the latching mecha- storage bin, children can die from suffocation or heat nism.
Page 168: Illuminated Vanity Mirrors - If Equipped
166 GETTING TO KNOW YOUR VEHICLE Coat Hooks — If Equipped Illuminated Vanity Mirrors — If Equipped Coat hooks are located along the headliner for the second An illuminated vanity mirror is located on the sun visor. To and third row seating positions. The coat hook load limit is use the mirror, rotate the sun visor down and swing the 10 lbs (4.5 kg).
Page 169: Sun Screens - If Equipped
GETTING TO KNOW YOUR VEHICLE 167 Sun Screens — If Equipped Once the screen is completely to the top of the window, extend the top bar of the sun screen over the two hooks Sun screens are available for second and third row seating attached to the top of the window.
Page 170: Power Outlets
168 GETTING TO KNOW YOUR VEHICLE Power Outlets CAUTION! (Continued) Your vehicle is equipped with 12 Volt (15 Amp) power this will damage the outlet and blow the fuse. Im- outlets, and 5 Volt (2.5 Amp) USB power outlets, that can be proper use of the power outlet can cause damage not used to power cellular phones, small electronics and other covered by your New Vehicle Limited Warranty.
Page 171 GETTING TO KNOW YOUR VEHICLE 169 The rear power outlet is located in the right rear cargo area. Front USB Charge Only Port In addition to the front power outlets, there is also a power Rear Power Outlet outlet located in the rear cargo area.
Page 172 170 GETTING TO KNOW YOUR VEHICLE NOTE: The USB outlet in the bottom of the instrument WARNING! panel can be switched from “ignition” only to constant “battery” powered all the time. See your local authorized To avoid serious injury or death: •...
Page 173: Power Inverter - If Equipped
GETTING TO KNOW YOUR VEHICLE 171 CAUTION! (Continued) • After the use of high power draw accessories, or long periods of the vehicle not being started (with acces- sories still plugged in), the vehicle must be driven a sufficient length of time to allow the generator to recharge the vehicle’s battery.
Page 174: Cigar Lighter - If Equipped
172 GETTING TO KNOW YOUR VEHICLE WARNING! CAUTION! To avoid serious injury or death: Do not connect devices with power higher than 180 • Do not insert any objects into the receptacles. Watts (15 Amps) to the socket. Do not damage the •...
Page 175: Overhead Storage With Sunglass Storage
GETTING TO KNOW YOUR VEHICLE 173 Overhead Storage With Sunglass Storage The door will slowly rotate to the full open position. At the front of the overhead console, a compartment is provided for the storage of one pair of sunglasses. From the closed position, push the door latch to open the compartment.
Page 176 174 GETTING TO KNOW YOUR VEHICLE ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and side rails are designed to carry weight on vehicles equipped with a luggage rack. The load must not exceed 150 lbs (68 kg), and should be uniformly distributed over the luggage rack crossbars.
Page 177 GETTING TO KNOW YOUR VEHICLE 175 Deploying The Crossbars 1. To deploy the crossbars, completely loosen the thumb screws at both ends of the crossbar and lift the crossbar from its stowed position in the side rail. Repeat with crossbar on the opposite side. Removing Crossbars CAUTION! Use care when removing and handling the crossbars to...
Page 178 176 GETTING TO KNOW YOUR VEHICLE 2. Bend the crossbar supports at each end, taking care to 3. Position the crossbars across the roof making sure the keep hand clear of pivoting joint. Slide the thumb screw letters on the crossbars align with the matching letters down.
Page 179 GETTING TO KNOW YOUR VEHICLE 177 4. Once the crossbar is in place, tighten both thumb screws matching letter to remove it from the deployed position. completely. Repeat with the other crossbar. CAUTION! Use care when removing and handling the crossbars to prevent damage to the vehicle.
Page 180 178 GETTING TO KNOW YOUR VEHICLE 3. Then, position the crossbar along the correct side rail. 4. The crossbar will nest fully within the side rail. Make sure the letters on the crossbar align with the matching letters on the side rail. Crossbar To Side Rail Stowing Crossbars...
Page 181 GETTING TO KNOW YOUR VEHICLE 179 5. Once the driver’s side crossbar is in place, tighten the 6. Repeat the procedure to stow the second crossbar on the thumb screws completely. opposite side. Tightening Crossbar Stowed Crossbars NOTE: • To help control wind noise, stow the crossbars in the side rails when they are not in use.
Page 182 180 GETTING TO KNOW YOUR VEHICLE WARNING! CAUTION! (Continued) points if needed. Tie loops are intended as supple- Cargo must be securely tied down before driving your mentary tie down points only. Do not use ratcheting vehicle. Improperly secured loads can fly off the ve- mechanisms with the tie loops.
Page 183 GETTING TO KNOW YOUR INSTRUMENT PANEL CONTENTS INSTRUMENT CLUSTER ....182 WARNING/INDICATOR LIGHTS AND MESSAGES ......197 ▫...
Page 184: Instrument Cluster
182 GETTING TO KNOW YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER Instrument Cluster...
Page 185: Instrument Cluster Descriptions
GETTING TO KNOW YOUR INSTRUMENT PANEL 183 Instrument Cluster 2. Instrument Cluster Display Instrument Cluster Descriptions • When the appropriate conditions exist, this display 1. Tachometer shows the instrument cluster display messages. Refer • Indicates the engine speed in revolutions per minute to “Display”...
Page 186: Instrument Cluster Display
184 GETTING TO KNOW YOUR INSTRUMENT PANEL 3. Speedometer WARNING! (Continued) • Indicates vehicle speed. into the normal range and is no longer red. If the gauge 4. Fuel Gauge remains on the “H”, turn the engine off immediately • The gauge shows the level of fuel in the fuel tank when and call an authorized dealer for service.
Page 187: Instrument Cluster Display Location And Controls
GETTING TO KNOW YOUR INSTRUMENT PANEL 185 driver interactive display located on the instrument panel, your instrument cluster display can show you how sys- tems are working and give you warnings when they aren’t. The steering wheel mounted controls allow you to scroll through and enter the main menus and sub-menus.
Page 188 186 GETTING TO KNOW YOUR INSTRUMENT PANEL • Right Arrow Button • OK Button Push and release the right arrow button to access Push the OK button to access/select the information the information screens or submenu screens of a screens or submenu screens of a Main Menu item. Push main menu item.
Page 189 GETTING TO KNOW YOUR INSTRUMENT PANEL 187 Menu Items Submenu Items • ACC/LaneSense Driver Assist — If Equipped • Average Fuel Economy value (hold OK to reset) Fuel Economy • Range • Current Fuel Economy gauge Trip Trip A / Trip B •...
Page 190: Oil Life Reset
188 GETTING TO KNOW YOUR INSTRUMENT PANEL Oil Life Reset Keyless Enter-N-Go — Ignition • Your vehicle is equipped with an engine oil change indicator system. The “Oil Change Due” message will display for approximately five seconds after a single chime has sounded, to indicate the next scheduled oil change interval.
Page 191: Keysense Cluster Messages - If Equipped
GETTING TO KNOW YOUR INSTRUMENT PANEL 189 4. Hold the OK button to reset the “Oil Life” to 100%. KeySense Cluster Messages — If Equipped When the KeySense key is in use there will be: 5. Push the up arrow button to exit the instrument cluster display menu screen.
Page 192: Instrument Cluster Display Menu Items
190 GETTING TO KNOW YOUR INSTRUMENT PANEL • If the Tire Pressure system requires service, “Service Tire Instrument Cluster Display Menu Items Pressure System” is displayed. NOTE: The instrument cluster display menu items display • Tire PSI is an information only function and cannot be in the center of the instrument cluster.
Page 193 GETTING TO KNOW YOUR INSTRUMENT PANEL 191 • If the conditions are not met, a popup message will – Range To Empty (miles or km) display for 5 seconds, describing the required condi- – Current Fuel Economy (MPG, L/100 km, or km/l) tions, and then the Oil Life screen will reappear.
Page 194 192 GETTING TO KNOW YOUR INSTRUMENT PANEL Messages Screen Setup Push and release the up or down arrow button until Push and release the up or down arrow button until the Messages is highlighted in the instrument cluster display. Screen Setup Menu displays in the instrument cluster This feature shows the number of stored warning mes- display.
Page 195 GETTING TO KNOW YOUR INSTRUMENT PANEL 193 Instrument Cluster Display Screen Setup Options: • None 2 — Center • Compass • Outside Temp. • Time • Range • Average MPG (L/100km, or km/L) • Current MPG (L/100km, or km/L) • Trip A Distance •...
Page 196: Battery Saver On/Battery Saver Mode Message - Electrical Load Reduction Actions - If Equipped
194 GETTING TO KNOW YOUR INSTRUMENT PANEL Instrument Cluster Display Screen Setup Options: • Show 4 — Odometer • Hide (Odometer will still appear when door is open) • Restore 5 — Defaults • Cancel Speed Warning — If Equipped NOTE: Speed Warning is unavailable while KeySense is in use.
Page 197 GETTING TO KNOW YOUR INSTRUMENT PANEL 195 • 150W Power Inverter System When load reduction is activated, the message “Battery Saver On” or “Battery Saver Mode” will appear in the • Audio and Telematics System instrument cluster display. Loss of the battery charge may indicate one or more of the These messages indicate the vehicle battery has a low state following conditions: of charge and continues to lose electrical charge at a rate...
Page 198: Trip Computer
196 GETTING TO KNOW YOUR INSTRUMENT PANEL • The battery was discharged by an electrical load left on • The vehicle should have service performed if the mes- when the vehicle was parked. sage is still present during consecutive trips and the evaluation of the vehicle and driving pattern did not •...
Page 199: Warning/Indicator Lights And Messages
GETTING TO KNOW YOUR INSTRUMENT PANEL 197 Elapsed Time All active telltales will display first, if applicable. The system check menu may appear different based upon Shows the total elapsed time of travel since the last reset equipment options and current vehicle status. Some tell- when the ignition switch is in the ACC position.
Page 200: Red Telltale Lights
198 GETTING TO KNOW YOUR INSTRUMENT PANEL Red Telltale Lights Air Bag Warning Light Red Telltale What It Means Light Air Bag Warning Light This light will turn on for four to eight seconds as a bulb check when the ignition switch is first turned to ON/RUN.
Page 201 GETTING TO KNOW YOUR INSTRUMENT PANEL 199 Brake Warning Light Red Telltale What It Means Light Brake Warning Light This light monitors various brake functions, including brake fluid level and parking brake appli- cation. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system reservoir.
Page 202 200 GETTING TO KNOW YOUR INSTRUMENT PANEL ON/RUN position. The light should illuminate for ap- WARNING! proximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is Driving a vehicle with the red brake light on is detected.
Page 203 GETTING TO KNOW YOUR INSTRUMENT PANEL 201 Engine Temperature Warning Light Red Telltale What It Means Light Engine Temperature Warning Light This light warns of an overheated engine condition. If the light turns on while driving, safely pull over and stop the vehicle. If the A/C system is on, turn it off. Also, shift the transmission into PARK and idle the vehicle.
Page 204 202 GETTING TO KNOW YOUR INSTRUMENT PANEL Electronic Throttle Control (ETC) Warning Light Red Telltale What It Means Light Electronic Throttle Control (ETC) Warning Light This light informs you of a problem with the Electronic Throttle Control (ETC) system. If a prob- lem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem.
Page 205 GETTING TO KNOW YOUR INSTRUMENT PANEL 203 Oil Pressure Warning Light Red Telltale What It Means Light Oil Pressure Warning Light This light indicates low engine oil pressure. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound when this light turns on. Do not operate the vehicle until the cause is corrected.
Page 206 204 GETTING TO KNOW YOUR INSTRUMENT PANEL Transmission Temperature Warning Light Red Telltale What It Means Light Transmission Temperature Warning Light This light indicates that the transmission fluid temperature is running hot. This may occur with severe usage. If this light turns on, safely pull over and stop the vehicle. Then, shift the transmis- sion into NEUTRAL and run the engine at idle or faster until the light turns off.
Page 207 GETTING TO KNOW YOUR INSTRUMENT PANEL 205 Door Open Warning Light — If Equipped Red Telltale What It Means Light Door Open Warning Light This indicator will illuminate when a door is ajar/open and not fully closed. NOTE: If the vehicle is moving, there will also be a single chime. Liftgate Open Warning Light Red Telltale What It Means...
Page 208: Yellow Telltale Lights
206 GETTING TO KNOW YOUR INSTRUMENT PANEL Yellow Telltale Lights Anti-Lock Brake (ABS) Indicator Light Yellow Telltale What It Means Light Anti-Lock Brake (ABS) Indicator Light This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition switch is placed in the ON/RUN position and may stay on for as long as four seconds.
Page 209 GETTING TO KNOW YOUR INSTRUMENT PANEL 207 Electronic Stability Control (ESC) Indicator Light Yellow Telltale What It Means Light Electronic Stability Control (ESC) Indicator Light — If Equipped The “ESC Indicator Light” in the instrument cluster will come on when the ignition is placed in the ON/RUN position.
Page 210 208 GETTING TO KNOW YOUR INSTRUMENT PANEL Electronic Stability Control (ESC) OFF Indicator Light — If Equipped Yellow Telltale What It Means Light Electronic Stability Control (ESC) OFF Indicator Light — If Equipped This light indicates the Electronic Stability Control (ESC) is off. Electronic Park Brake Fail Light Yellow Telltale What It Means...
Page 211 GETTING TO KNOW YOUR INSTRUMENT PANEL 209 LaneSense Indicator Light — If Equipped Yellow Telltale What It Means Light LaneSense Indicator Light — If Equipped The LaneSense is solid yellow when the system senses a lane drift situation. The LaneSense is flashing yellow when the system senses the lane has been approached and is in a lane departure situation.
Page 212 210 GETTING TO KNOW YOUR INSTRUMENT PANEL Low Fuel Warning Light Yellow Telltale What It Means Light Low Fuel Indicator Light When the fuel level reaches approximately 2.4 gal (9.1 L) this light will turn on, and remain on until fuel is added. A single warning chime will sound with Low Fuel Warning.
Page 213 GETTING TO KNOW YOUR INSTRUMENT PANEL 211 Service Adaptive Cruise Control (ACC) System Indicator Light Yellow Telltale What It Means Light Service Adaptive Cruise Control Indicator Light This light will turn on when a ACC is not operating and needs service. Refer to “Adaptive Cruise Control (ACC) —...
Page 214 212 GETTING TO KNOW YOUR INSTRUMENT PANEL Engine Malfunction Warning Light Yellow Telltale What It Means Light Vehicle Check/Malfunction Indicator Light (MIL) The Vehicle Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors emissions control systems. The light will illuminate when the igni- tion is in the ON position before vehicle start up.
Page 215 GETTING TO KNOW YOUR INSTRUMENT PANEL 213 Rear Fog Light Indicator Yellow Telltale What It Means Light Rear Fog Light Indicator This indicator will illuminate when the rear fog lights are on. Tire Pressure Monitoring System (TPMS) Warning Light Yellow Telltale What It Means Light Tire Pressure Monitoring System (TPMS) Warning Light...
Page 216 214 GETTING TO KNOW YOUR INSTRUMENT PANEL As an added safety feature, your vehicle has been indicator is illuminated, the system may not be able to equipped with a tire pressure monitoring system (TPMS) detect or signal low tire pressure as intended. TPMS that illuminates a low tire pressure telltale when one or malfunctions may occur for a variety of reasons, including more of your tires is significantly under-inflated.
Page 217: Green Telltale Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL 215 Service Stop/Start System Indicator Light — If Equipped Yellow Telltale What It Means Light Service Stop/Start System Indicator Light This telltale will turn on to indicate the Stop/Start system is not functioning properly and service is required.
Page 218 216 GETTING TO KNOW YOUR INSTRUMENT PANEL LaneSense Indicator Light — If Equipped Green Telltale What It Means Light LaneSense Indicator Light The LaneSense indicator is solid green when both lane markings have been detected and the sys- tem is “armed” to provide visual warnings in the instrument cluster display and a torque warn- ing in the steering wheel if an unintentional lane departure occurs.
Page 219 GETTING TO KNOW YOUR INSTRUMENT PANEL 217 Adaptive Cruise Control (ACC) Set With Target Detected Light — If Equipped Green Telltale What It Means Light Adaptive Cruise Control (ACC) Set With Target Detected Light — If Equipped This light will turn on when the Adaptive Cruise Control speed is SET and the target vehicle is detected.
Page 220: Headlights
218 GETTING TO KNOW YOUR INSTRUMENT PANEL Park/Headlight ON Indicator Light Green Telltale What It Means Light Park/Headlight ON Indicator Light This indicator will illuminate when the park lights or headlights are turned on. Front Fog Indicator Light — If Equipped Green Telltale What It Means Light...
Page 221: Blue Telltale Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL 219 Blue Telltale Lights High Beam Indicator Light Blue Telltale What It Means Light High Beam Indicator Light This indicator shows that the high beam headlights are on. Push the multifunction control lever away from you to switch the headlights to high beam. Pull the lever toward you to switch the headlights back to low beam.
Page 222 220 GETTING TO KNOW YOUR INSTRUMENT PANEL LaneSense Indicator Light — If Equipped White Telltale What It Means Light LaneSense Indicator Light When the LaneSense system is ON, the LaneSense indicator is solid white when none or only the left or right lane marking has been detected. The indicator will turn green when both lanes are detected and the system will be ready to provide visual warnings in the instrument cluster dis- play if an unintentional lane departure occurs.
Page 223 GETTING TO KNOW YOUR INSTRUMENT PANEL 221 Set Speed Warning Light — If Equipped White Warning What It Means Light Set Speed Warning Light When Set Speed Warning is turned on, the speed warning telltale will illuminate in the instru- ment cluster with a number matching the set speed.
Page 224: Onboard Diagnostic System - Obd Ii
222 GETTING TO KNOW YOUR INSTRUMENT PANEL Passive Speed Limiter White Telltale What It Means Light Passive Speed Limiter The indication light up white along with a notification text message (speed warning set to xx fol- lowed by unit). When the set speed is just exceeded, a single chime will sound along with pop up message of speed warning exceeded.
Page 225: Onboard Diagnostic System (Obd Ii) Cybersecurity
GETTING TO KNOW YOUR INSTRUMENT PANEL 223 Onboard Diagnostic System (OBD II) Cybersecurity For further information, refer to “Cybersecurity” in “Mul- timedia” or “Privacy Practices” and “Uconnect CyberSecu- Your vehicle is required to have an Onboard Diagnostic rity” in “All About Uconnect Access” in your Owner’s system (OBD II) and a connection port to allow access to Manual Radio Supplement.
Page 226 224 GETTING TO KNOW YOUR INSTRUMENT PANEL • The MIL will not flash at all and will remain fully Your vehicle has a simple ignition actuated test, which you can use prior to going to the test station. To check if your illuminated until you place the ignition in the off posi- vehicle’s OBD II system is ready, you must do the follow- tion or start the engine.
Page 227 SAFETY CONTENTS ▫ Seat Belt Systems ..... .254 SAFETY FEATURES ..... .226 ▫...
Page 228: Safety Features
226 SAFETY SAFETY FEATURES These are all normal characteristics of ABS. Anti-Lock Brake System (ABS) WARNING! The Anti-Lock Brake System (ABS) provides increased • The ABS contains sophisticated electronic equip- vehicle stability and brake performance under most brak- ment that may be susceptible to interference caused ing conditions.
Page 229: Electronic Brake Control System
SAFETY Electronic Brake Control System WARNING! (Continued) Your vehicle is equipped with an advanced Electronic • The capabilities of an ABS equipped vehicle must Brake Control system (EBC). This system includes Elec- never be exploited in a reckless or dangerous manner tronic Brake Force Distribution (EBD), Anti-Lock Brake that could jeopardize the user’s safety or the safety of System (ABS), Brake Assist System (BAS), Hill Start Assist...
Page 230 228 SAFETY will allow more vehicle torque to be applied to the wheel WARNING! (Continued) that is not spinning. BLD may remain enabled even if TCS conditions. BAS cannot prevent collisions, including and ESC are in a reduced mode. those resulting from excessive speed in turns, driving Brake Assist System (BAS) on very slippery surfaces, or hydroplaning.
Page 231 SAFETY in which the ESC module is detecting vehicle instability. of the vehicle. When ERM determines that the rate of The torque that the steering wheel receives is only meant to change of the steering wheel angle and vehicle’s speed are help the driver realize optimal steering behavior in order to sufficient to potentially cause wheel lift, it then applies the reach/maintain vehicle stability.
Page 232 230 SAFETY for oversteering or understeering of the vehicle by apply- WARNING! ing the brake of the appropriate wheel(s) to assist in • Electronic Stability Control (ESC) cannot prevent the counteracting the oversteer or understeer condition. En- gine power may also be reduced to help the vehicle natural laws of physics from acting on the vehicle, maintain the desired path.
Page 233 SAFETY To enter the “Partial Off” mode, momentarily push the “ESC WARNING! (Continued) Off” switch and the “ESC Off Indicator Light” will illumi- vehicle modification or poor vehicle maintenance nate. To turn the ESC on again, momentarily push the “ESC that reduces the effectiveness of the ESC system can Off”...
Page 234 232 SAFETY ESC Activation/Malfunction Indicator Light and ESC NOTE: OFF Indicator Light • The “ESC Activation/Malfunction Indicator Light” and the “ESC OFF Indicator Light” come on momentarily each time the ignition is turned ON. The “ESC Activation/Malfunction Indicator Light” in the instrument cluster will come on •...
Page 235 SAFETY The following conditions must be met in order for HSA to WARNING! (Continued) activate: active driving involvement. It is always the driver’s • The feature must be enabled. responsibility to be attentive to distance to other ve- • The vehicle must be stopped. hicles, people, and objects, and most importantly brake operation to ensure safe operation of the vehicle under •...
Page 236 234 SAFETY Ready Alert Braking (RAB) WARNING! (Continued) Ready Alert Braking may reduce the time required to reach or apply more vehicle brake pressure prior to releas- full braking during emergency braking situations. It antici- ing the brake pedal. pates when an emergency braking situation may occur by •...
Page 237: Auxiliary Driving Systems
SAFETY WARNING! If TSC activates while driving, slow the vehicle down, stop at the nearest safe location, and adjust the trailer load to eliminate trailer sway. AUXILIARY DRIVING SYSTEMS Blind Spot Monitoring (BSM) — If Equipped The Blind Spot Monitoring (BSM) system uses two radar- based sensors, located inside the rear bumper fascia, to detect highway licensable vehicles (automobiles, trucks, motorcycles, etc.) that enter the blind spot zones from the...
Page 238 236 SAFETY both sides of the vehicle when the vehicle speed reaches approximately 6 mph (10 km/h) or higher and will alert the driver of vehicles in these areas. NOTE: • The BSM system DOES NOT alert the driver about rapidly approaching vehicles that are outside the detec- tion zones.
Page 239 SAFETY If the blockage message is still present after cycling the Entering From The Side ignition and driving in traffic, check again for a blockage. Vehicles that move into your adjacent lanes from either The BSM system notifies the driver of objects in the side of the vehicle.
Page 240 238 SAFETY Entering From The Rear Overtaking Traffic Vehicles that come up from behind your vehicle on either If you pass another vehicle slowly with a relative speed less side and enter the rear detection zone with a relative speed than 15 mph (24 km/h) and the vehicle remains in the of less than 30 mph (48 km/h).
Page 241 SAFETY Overtaking/Passing Stationary Objects The BSM system is designed not to issue an alert on The BSM system will not alert you of objects that are stationary objects such as guardrails, posts, walls, foliage, traveling in the opposite direction of the vehicle in adjacent berms, snow banks, car washes etc.
Page 242 240 SAFETY Rear Cross Path (RCP) The Rear Cross Path (RCP) feature is intended to aid the driver when backing out of parking spaces where their vision of oncoming vehicles may be blocked. Proceed slowly and cautiously out of the parking space until the rear end of the vehicle is exposed.
Page 243 SAFETY (5 km/h), to objects moving a maximum of approximately Modes Of Operation 20 mph (32 km/h), such as in parking lot situations. Three selectable modes of operation are available in the Uconnect System. Refer to “Uconnect Settings” in “Multi- NOTE: In a parking lot situation, oncoming vehicles can be media”...
Page 244: Forward Collision Warning (Fcw) With Mitigation - If Equipped
242 SAFETY NOTE: Whenever an audible alert is requested by the BSM General Information system, the radio is also muted. This vehicle has systems that operate on radio frequency that comply with Part 15 of the Federal Communications When the system is in RCP, the system shall respond with Commission (FCC) rules and with Industry Canada Stan- both visual and audible alerts when a detected object is dards RSS- GEN/210/220/310.
Page 245 SAFETY NOTE: FCW monitors the information from the forward looking sensors as well as the Electronic Brake Controller (EBC), to calculate the probability of a forward collision. When the system determines that a forward collision is probable, the driver will be provided with audible and visual warnings and may provide a brake jerk warning.
Page 246 244 SAFETY • It is unsafe to test the FCW system. To prevent such Changing the FCW status to “off” deactivates the system, misuse of the system, after four Active Braking events so no warning or active braking will be available in case of within a key cycle, the Active Braking portion of FCW a possible collision will be deactivated until the next key cycle.
Page 247 SAFETY Changing the FCW status to “Far” setting allows the NOTE: system to warn the driver of a possible collision with the • The system will retain the last setting selected by the vehicle in front using audible/visual warning when the driver after ignition shut down.
Page 248: Tire Pressure Monitor System (Tpms)
246 SAFETY Service FCW Warning vehicle’s tires. The tire pressure will also increase as the vehicle is driven. This is normal and there should be no If the system turns off, and the instrument cluster displays: adjustment for this increased pressure. •...
Page 249 SAFETY may need to be driven for up to 20 minutes above 15 mph CAUTION! (Continued) (24 km/h) in order for the TPMS to receive this informa- replacement equipment that is not of the same size, tion. type, and/or style. The TPM sensor is not designed For example, your vehicle may have a recommended cold for use on aftermarket wheels and may contribute to (parked for more than three hours) placard pressure of 33...
Page 250 248 SAFETY • Driving on a significantly underinflated tire causes the The TPMS consists of the following components: tire to overheat and can lead to tire failure. Underinfla- • Receiver Module tion also reduces fuel efficiency and tire tread life, and •...
Page 251 SAFETY NOTE: When filling warm tires, the tire pressure may need 4. Using tire chains on the vehicle. to be increased up to an additional 4 psi (28 kPa) above the 5. Using wheels/tires not equipped with TPMS sensors. recommended cold placard pressure in order to turn the Tire Pressure Monitoring Telltale Light off.
Page 252 250 SAFETY off, as long as no tire pressure is below the low-pressure Tire Pressure Monitoring Low Pressure Warnings warning limit in any of the four active road tires. The vehicle may need to be driven for up to 20 minutes The “Tire Pressure Monitoring Telltale Light”...
Page 253 SAFETY in the instrument cluster graphic) to the vehicle’s recom- will no longer display, and a pressure value will display in mended cold placard pressure value as shown in the place of the dashes. A system fault can occur due to any of Inflate to XX message.
Page 254 252 SAFETY 3. After driving the vehicle for up to 20 minutes above TPMS Deactivation — If Equipped 15 mph (24 km/h), the “TPM Telltale Light” will flash The TPMS can be deactivated if replacing all four wheel on and off for 75 seconds and then remain on solid. In and tire assemblies (road tires) with wheel and tire assem- addition, the instrument cluster will display a “SER- blies that do not have TPMS Sensors, such as when...
Page 255: Occupant Restraint Systems
SAFETY place of the dashes. On the next ignition cycle the SER- Occupant Restraint Systems Features VICE TPM SYSTEM message will no longer be displayed • Seat Belt Systems as long as no system fault exists. • Supplemental Restraint Systems (SRS) Air Bags General Information •...
Page 256: Seat Belt Systems
254 SAFETY 3. Children that are not big enough to wear the vehicle seat 9. If the air bag system in this vehicle needs to be modified belt properly (refer to “Child Restraints” in this section to accommodate a disabled person, refer to the “Cus- for further information) should be secured in a vehicle tomer Assistance”...
Page 257 SAFETY risk of injury caused by striking the inside of the vehicle. BeltAlert Warning Sequence Everyone in a motor vehicle should be belted at all times. The BeltAlert warning sequence is activated when the Enhanced Seat Belt Use Reminder System (BeltAlert) vehicle is moving above a specified vehicle speed range and the driver or outboard front seat passenger is unbuck- Driver And Passenger BeltAlert —...
Page 258 256 SAFETY The outboard front passenger seat BeltAlert is not active and reduce your risk of striking the inside of the vehicle or when the outboard front passenger seat is unoccupied. being thrown out of the vehicle. BeltAlert may be triggered when an animal or other items are placed on the outboard front passenger seat or when WARNING! the seat is folded flat (if equipped).
Page 259 SAFETY WARNING! (Continued) WARNING! (Continued) • A twisted seat belt may not protect you properly. In driver, should always wear their seat belts whether or not an air bag is also provided at their seating a collision, it could even cut into you. Be sure the seat position to minimize the risk of severe injury or belt is flat against your body, without twists.
Page 260 258 SAFETY 2. The seat belt latch plate is above the back of the front WARNING! (Continued) seat, and next to your arm in the rear seat (for vehicles • A shoulder belt placed behind you will not protect equipped with a rear seat). Grasp the latch plate and you from injury during a collision.
Page 261 SAFETY 3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Positioning The Lap Belt 5. Position the shoulder belt across the shoulder and chest with minimal, if any slack so that it is comfortable and Inserting Latch Plate Into Buckle not resting on your neck.
Page 262 260 SAFETY Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate.
Page 263 SAFETY NOTE: The adjustable upper shoulder belt anchorage is buckle, which allows the seat belt to detach from the lower equipped with an Easy Up feature. This feature allows the anchor when the seat is folded. The mini-latch plate and shoulder belt anchorage to be adjusted in the upward regular latch plate can then be stored out of the way in the position without pushing or squeezing the release button.
Page 264 262 SAFETY 2. Grasp the mini-latch plate and pull the seat belt over the seat. Mini-Latch And Buckle Connected 4. When the seat belt is long enough to fit, insert the mini-latch plate into the mini-buckle until you hear a Mini-Latch Plate “click.”...
Page 265 SAFETY Connect Mini-Latch To Buckle 1 — Seat Belt Latch Plate 5. Sit back in seat. Slide the regular latch plate up the 6. When the seat belt is long enough to fit, insert the latch webbing as far as necessary to allow the seat belt to go plate into the buckle until you hear a “click.”...
Page 266 264 SAFETY 8. Position the shoulder belt on your chest so that it is comfortable and not resting on your neck. The retractor will withdraw any slack in the seat belt. 9. To release the seat belt, push the red button on the buckle.
Page 267 SAFETY WARNING! (Continued) WARNING! procedure to detach the mini-latch plate and mini- • ONLY use the Seat Belt Extender if it is physically buckle, untwist the webbing, and reattach the mini- required in order to properly fit the original seat belt latch plate and mini-buckle.
Page 268 266 SAFETY Seat Belts And Pregnant Women Seat Belt Pretensioner The front seat belt system is equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices may improve the performance of the seat belt by removing slack from the seat belt early in a collision.
Page 269 SAFETY Switchable Automatic Locking Retractors (ALR) The seat belts in the passenger seating positions are equipped with a Switchable Automatic Locking Retractor (ALR) which is used to secure a child restraint system. For additional information, refer to “Installing Child Restraints Using The Vehicle Seat Belt”...
Page 270 268 SAFETY In Automatic Locking Mode, the shoulder belt is automati- 3. Allow the seat belt to retract. As the seat belt retracts, cally pre-locked. The seat belt will still retract to remove you will hear a clicking sound. This indicates the seat any slack in the shoulder belt.
Page 271 SAFETY Seat Belt Park Stitch — If Equipped Third Row Stow Clip — If Equipped The rear outboard seat belts may be equipped with a park Your vehicle may be equipped with a stow clip on the stitch to raise the latch plate for easier access to occupants. lower trim behind the third row.
Page 272: Supplemental Restraint Systems (Srs)
270 SAFETY • Instrument Panel WARNING! • Knee Impact Bolsters Do not place the seat belt webbing behind the third • Driver and Front Passenger Air Bags row stow clip when using the seat belt to restrain an occupant. The seat belt will not be positioned properly •...
Page 273 SAFETY The ORC turns on the Air Bag Warning Light in the NOTE: If the speedometer, tachometer, or any engine instrument panel for approximately four to eight seconds related gauges are not working, the Occupant Restraint for a self-check when the ignition switch is first in the Controller (ORC) may also be disabled.
Page 274 272 SAFETY Redundant Air Bag Warning Light comes on intermittently or remains on while driving have an authorized dealer service the vehicle immediately. For additional information regarding the Redundant Air Bag Warning Light, refer to “Warning/Indicator Lights And Messages” in “Getting to Know Your Instrument Panel”...
Page 275 SAFETY driver or front passenger seat belt is buckled. The seat belt WARNING! (Continued) buckle switch may adjust the inflation rate of the Ad- • Never place a rear-facing child restraint in front of an vanced Front Air Bags. air bag. A deploying passenger front air bag can This vehicle may be equipped with driver and/or front cause death or serious injury to a child 12 years or passenger seat track position sensors that may adjust the...
Page 276 274 SAFETY Because air bag sensors measure vehicle deceleration over WARNING! (Continued) time, vehicle speed and damage by themselves are not bags may no longer be functional. The protective good indicators of whether or not an air bag should have covers for the air bag cushions are designed to open deployed.
Page 277 SAFETY • The front passenger seat is unoccupied or has very light The Occupant Classification System (OCS) consists of the following: objects on it; or • Occupant Restraint Controller (ORC) • The front passenger seat is occupied by a small passen- ger, including a child;...
Page 278 276 SAFETY never install a child restraint system, including a rear-facing In order for the OCS to operate as designed, it is important child restraint, in the front passenger seat. for the front passenger to be seated properly and properly wearing the seat belt.
Page 279 SAFETY Lighter Weight Passengers (Including Small Adults) Examples of improper front passenger seating include: • The front passenger’s weight is transferred to another When a lighter weight passenger, including a small adult, part of the vehicle (like the door, arm rest or instrument occupies the front passenger seat, the OCS may reduce the panel).
Page 280 278 SAFETY The OCS determines the front passenger’s most probable classification. If an occupant in the front passenger seat is seated improperly, the occupant may provide an output signal to the OCS that is different from the occupant’s properly seated weight input, for example: Not Seated Properly Not Seated Properly...
Page 281 SAFETY Not Seated Properly Not Seated Properly WARNING! • If a child restraint system, child, small teenager or adult in the front passenger seat is seated improp- erly, the occupant may provide an output signal to the OCS that is different from the occupant’s prop- erly seated weight input.
Page 282 280 SAFETY The passenger seat assembly contains critical OCS compo- WARNING! (Continued) nents that may affect the Passenger Advanced Front Air the seatback, sitting upright, facing forward, in the Bag inflation. In order for the OCS to properly classify the center of the seat, with your feet comfortably on or seated weight of a front seat passenger, the OCS compo- near the floor.
Page 283 SAFETY be modified or replaced with any part except those WARNING! which are approved by FCA US LLC. • Do not drill, cut, or tamper with the knee impact WARNING! bolsters in any way. • Do not mount any accessories to the knee impact •...
Page 284 282 SAFETY WARNING! Do not use accessory seat covers or place objects between you and the SABs; the performance could be adversely affected and/or objects could be pushed into you, causing serious injury. 2. Supplemental Side Air Bag Inflatable Curtains (SABICs): Located above the side windows.
Page 285 SAFETY SABICs may help reduce the risk of head or other injuries WARNING! (Continued) to front and rear seat outboard occupants in certain side require permanent attachments (bolts or screws) for impacts and/or vehicle rollover events, in addition to the installation on the vehicle roof.
Page 286 284 SAFETY WARNING! (Continued) WARNING! (Continued) • Relying on the Side Air Bags alone could lead to never lean on or sleep against the door, side win- dows, or area where the side air bags inflate, even if more severe injuries in a collision. The Side Air Bags work with your seat belt to restrain you properly.
Page 287 SAFETY Rollover Events Air Bag System Components • Occupant Restraint Controller (ORC) Side Air Bags are designed to activate in certain rollover events. The ORC determines whether the deployment of • Air Bag Warning Light the Side Air Bags in a particular rollover event is appro- •...
Page 288 286 SAFETY If A Deployment Occurs irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, The front air bags are designed to deflate immediately after follow the garment manufacturer’s instructions for deployment.
Page 289 SAFETY Enhanced Accident Response System Maintaining Your Air Bag System In the event of an impact, if the communication network WARNING! remains intact, and the power remains intact, depending on the nature of the event, the ORC will determine whether •...
Page 290: Child Restraints
288 SAFETY • These data can help provide a better understanding of WARNING! (Continued) the circumstances in which crashes and injuries occur. dealer. Only manufacturer approved seat accessories NOTE: EDR data are recorded by your vehicle only if a may be used. If it is necessary to modify the air bag non-trivial crash situation occurs;...
Page 291 SAFETY Children 12 years or younger should ride properly buckled Before buying any restraint system, make sure that it has a up in a rear seat, if available. According to crash statistics, label certifying that it meets all applicable Safety Stan- children are safer when properly restrained in the rear dards.
Page 292 290 SAFETY Summary Of Recommendations For Restraining Children In Vehicles Recommended Type Of Child Re- Child Size, Height, Weight Or Age straint Infants and Toddlers Children who are two years old or Either an Infant Carrier or a Convert- younger and who have not reached ible Child Restraint, facing rearward the height or weight limits of their in the rear seat of the vehicle...
Page 293 SAFETY Infant And Child Restraints WARNING! (Continued) Safety experts recommend that children ride rear-facing in • Only use a rear-facing child restraint in a vehicle the vehicle until they are two years old or until they reach with a rear seat. either the height or weight limit of their rear-facing child restraint.
Page 294 292 SAFETY Older Children And Child Restraints WARNING! Children who are two years old or who have outgrown • Improper installation can lead to failure of an infant their rear-facing convertible child seat can ride forward- or child restraint. It could come loose in a collision. facing in the vehicle.
Page 295 SAFETY Children Too Large For Booster Seats If the answer to any of these questions was “no,” then the child still needs to use a booster seat in this vehicle. If the Children who are large enough to wear the shoulder belt child is using the lap/shoulder belt, check seat belt fit comfortably, and whose legs are long enough to bend over periodically and make sure the seat belt buckle is latched.
Page 296 294 SAFETY Recommendations For Attaching Child Restraints Restraint Type Combined Use Any Attachment Method Shown With An “X” Below Weight of the LATCH – Lower Seat Belt Only LATCH – Lower Seat Belt + Top Child + Child Anchors Only Anchors + Top Tether Anchor Restraint...
Page 297 SAFETY Lower Anchors And Tethers For CHildren (LATCH) vehicle anchor points for installing LATCH-equipped child Restraint System seats. There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position. These anchorages are used to install LATCH-equipped child seats without using the vehicle’s seat belts.
Page 298 296 SAFETY LATCH Positions For Installing Child Restraints In This Vehicle 8 Passenger LATCH Positions • Lower Anchorage Symbol 2 anchorages per seat- ing position 7 Passenger LATCH Positions • Top Tether Anchorage Symbol...
Page 299 SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH Frequently Asked Questions What is the weight limit (child’s 65 lbs (29.5 kg) Use the LATCH anchorage system weight + weight of the child re- until the combined weight of the straint) for using the LATCH anchor- child and the child restraint is 65 lbs age system to attach the child re-...
Page 300 298 SAFETY Frequently Asked Questions Can the rear-facing child restraint The child seat may touch the back of touch the back of the front passenger the front passenger seat if the child seat? restraint manufacturer also allows contact. See your child restraint own- er’s manual for more information.
Page 301 SAFETY Locating The LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage sym- bols on the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between the seatback and seat cushion.
Page 302 300 SAFETY LATCH Anchorages (Third Row 60/40 Anchorages Shown) Tether Strap Anchorages (Third Row 60/40 Anchorage Shown) Locating The Upper Tether Anchorages LATCH-compatible child restraint systems will be There are tether strap anchorages located behind all equipped with a rigid bar or a flexible strap on each side. second row seating positions.
Page 303 SAFETY Center Seat LATCH not use that outboard position. If a child seat in the center position blocks the outboard LATCH anchors or seat belt, This vehicle has 4 lower LATCH anchorages in the third do not install a child seat in that outboard position. row, rear seat.
Page 304 302 SAFETY 1. Loosen the adjusters on the lower straps and on the 6. Test that the child restraint is installed tightly by pulling tether strap of the child seat so that you can more easily back and forth on the child seat at the belt path. It should attach the hooks or connectors to the vehicle anchor- not move more than 1 inch (25.4 mm) in any direction.
Page 305 SAFETY The seat belts in the passenger seating positions are WARNING! (Continued) equipped with a Switchable Automatic Locking Retractor Follow the child restraint manufacturer’s directions (ALR) that is designed to keep the lap portion of the seat exactly when installing an infant or child restraint. belt tight around the child restraint so that it is not •...
Page 306 304 SAFETY Lap/Shoulder Belt Systems For Installing Child Restraints In This Vehicle 8 Passenger LATCH Positions • Lower Anchorage Symbol 2 anchorages per seat- ing position 7 Passenger LATCH Positions • Top Tether Anchorage Symbol...
Page 307 SAFETY Frequently Asked Question About Installing Child Restraints With Seat Belts Frequently Asked Questions What is the weight limit (child’s Weight limit of the Child Restraint Always use the tether anchor when weight + weight of the child re- using the seat belt to install a for- straint) for using the Tether Anchor ward facing child restraint, up to the with the seat belt to attach a forward...
Page 308 306 SAFETY NOTE: If the folding, non-adjustable head restraint inter- feres with the installation of the child restraint, the head restraint may be folded and the child seat installed in front of it. WARNING! Always make sure the head restraint is in its upright position when the seat is to be used by an occupant who is not in a child restraint.
Page 309 SAFETY back into the retractor. As the webbing retracts, you will WARNING! hear a clicking sound. This means the seat belt is now in • Improper installation or failure to properly secure a the Automatic Locking mode. child restraint can lead to failure of the restraint. The 6.
Page 310 308 SAFETY Seat Belt Park Stitch — If Equipped switch the seat belt to the locking mode, as described in the steps above or move the car seat to a different seating The rear outboard seat belts may be equipped with a park position.
Page 311 SAFETY WARNING! (Continued) strap of a rear-facing car seat to the tether anchorage that is approved for that seating position, located behind the top of the vehicle seat. See the section “Lower Anchors and Tethers for CHildren (LATCH) Restraint System” for the location of approved tether anchorages in your vehicle.
Page 312 310 SAFETY 4. Remove slack in the tether strap according to the child WARNING! (Continued) restraint manufacturer’s instructions. • If your vehicle is equipped with a split rear seat, make sure the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap.
Page 313 SAFETY 4. Remove slack in the tether strap according to the child restraint manufacturer’s instructions. Outboard Tether Attachments – 3rd Row WARNING! Center Tether Attachment – 3rd Row Do not connect the tether strap for more than one child restraint to the tether anchorage on the 60% seat in the third row.
Page 314: Transporting Pets
312 SAFETY Transporting Pets WARNING! (Continued) Air Bags deploying in the front seat could harm your pet. An • Be sure everyone in your vehicle is in a seat and unrestrained pet will be thrown about and possibly injured, using a seat belt properly. or injure a passenger during panic braking or in a collision.
Page 315: Safety Checks You Should Make Inside The Vehicle
SAFETY The best protection against carbon monoxide entry into the Air Bag Warning Light vehicle body is a properly maintained engine exhaust The Air Bag warning light will turn on for four to system. eight seconds as a bulb check when the ignition switch Whenever a change is noticed in the sound of the exhaust is first turned to ON/RUN.
Page 316 314 SAFETY that is securely attached using the floor mat fasteners so it WARNING! (Continued) cannot slip out of position and interfere with the accelera- needs to be replaced, only use a FCA approved floor tor, brake or clutch pedals or impair safe operation of your mat for the specific make, model, and year of your vehicle in other ways.
Page 317: Periodic Safety Checks You Should Make Outside
SAFETY Lights WARNING! (Continued) Have someone observe the operation of brake lights and with the accelerator, brake, or clutch pedals. exterior lights while you work the controls. Check turn • If the vehicle carpet has been removed and re- signal and high beam indicator lights on the instrument installed, always properly attach carpet to the floor panel.
Page 319 STARTING AND OPERATING CONTENTS ▫ Nine-Speed Automatic Transmission ..330 STARTING PROCEDURES ....321 ▫ Normal Starting ..... . .321 ▫...
Page 320 318 STARTING AND OPERATING ▫ To Set A Desired Speed....341 ▫ ACC Operation At Stop ....353 ▫...
Page 321 STARTING AND OPERATING 319 ▫ ParkSense Visual Alert ....375 ▫ Changing LaneSense Status ....412 ▫...
Page 322 320 STARTING AND OPERATING RECREATIONAL TOWING (BEHIND DRIVING TIPS ......433 MOTORHOME, ETC.) ....432 ▫...
Page 323: Starting Procedures
STARTING AND OPERATING 321 STARTING PROCEDURES Start the engine with the gear selector in the NEUTRAL or PARK position. Apply the brake before shifting to any Before starting your vehicle, adjust your seat, adjust both driving range. inside and outside mirrors, and fasten your seat belts. Normal Starting WARNING! NOTE: Normal starting of either a cold or a warm engine...
Page 324: Cold Weather Operation (Below -22°F Or −30°C)
322 STARTING AND OPERATING ENGINE START/STOP Button Functions — With Driv- After Starting — Warming Up The Engine er’s Foot OFF The Brake Pedal (In PARK Or NEUTRAL The idle speed is controlled automatically and it will Position) decrease as the engine warms up. The ENGINE START/STOP button operates similar to an If Engine Fails To Start ignition switch.
Page 325: To Turn Off The Engine Using Engine Start/Stop Button
STARTING AND OPERATING 323 To Turn Off The Engine Using ENGINE ENGINE BLOCK HEATER — IF EQUIPPED START/STOP Button The engine block heater warms the engine and permits quicker starts in cold weather. 1. Place the gear selector in PARK, then push and release the ENGINE START/STOP button.
Page 326: Engine Break-In Recommendations
324 STARTING AND OPERATING NOTE: While cruising, brief full-throttle acceleration within the limits of local traffic laws contributes to a good break-in. • The engine block heater cord is a factory installed Wide-open throttle acceleration in low gear can be detri- option.
Page 327: Park Brake
STARTING AND OPERATING 325 PARK BRAKE Electric Park Brake (EPB) Your vehicle is equipped with an Electric Park Brake System (EPB) that offers simple operation, and some additional features that make the park brake more conve- nient and useful. The park brake is primarily intended to prevent the vehicle from rolling while parked.
Page 328 326 STARTING AND OPERATING NOTE: The EPB fault lamp will illuminate if the EPB Once the park brake is fully disengaged, the BRAKE switch is held for longer than 180 seconds. The light will warning lamp in the instrument cluster and the LED extinguish upon releasing the switch.
Page 329 STARTING AND OPERATING 327 WARNING! (Continued) CAUTION! of reasons. A child or others could be seriously or If the Brake System Warning Light remains on with the fatally injured. Children should be warned not to parking brake released, a brake system malfunction is touch the parking brake, brake pedal or the trans- indicated.
Page 330 328 STARTING AND OPERATING Auto Park Brake Brake Service Mode The Electric Park Brake can be programmed to be applied We recommend having your brakes serviced by your automatically whenever the vehicle is at a standstill and authorized dealer. You should only make repairs for which the automatic transmission is placed in PARK.
Page 331: Automatic Transmission
STARTING AND OPERATING 329 When brake service work is complete, the following steps CAUTION! (Continued) must be followed to reset the parking brake system to • Do not shift between PARK, REVERSE, NEUTRAL, normal operation: or DRIVE when the engine is above idle speed. •...
Page 332: Ignition Park Interlock
330 STARTING AND OPERATING ignition can be turned to the OFF mode. This helps the WARNING! (Continued) driver avoid inadvertently leaving the vehicle without locked in PARK, securing the vehicle against un- placing the transmission in PARK. This system also locks wanted movement.
Page 333: Gear Ranges
STARTING AND OPERATING 331 rotate it, to access the L position. You must also press the Software and calibration is refined to optimize the custom- brake pedal to shift the transmission out of PARK, or to er’s driving experience and fuel economy. By design, some shift from NEUTRAL into DRIVE or REVERSE when the vehicle and driveline combinations utilize 9th gear only in vehicle is stopped or moving at low speeds (refer to...
Page 334 332 STARTING AND OPERATING NOTE: After selecting any gear range, wait a moment to WARNING! (Continued) allow the selected gear to engage before accelerating. This • Your vehicle could move and injure you and others if is especially important when the engine is cold. it is not in PARK.
Page 335 STARTING AND OPERATING 333 WARNING! (Continued) CAUTION! • When leaving the vehicle, always make sure the • Before moving the transmission gear selector out of ignition is in the OFF mode, remove the key fob from PARK, you must place the ignition from the LOCK/ the vehicle, and lock the vehicle.
Page 336 334 STARTING AND OPERATING NEUTRAL (N) upshifts through all forward gears. The DRIVE position provides optimum driving characteristics under all normal Use this range when the vehicle is standing for prolonged operating conditions. periods with the engine running. The engine may be started in this range.
Page 337 STARTING AND OPERATING 335 LOW (L) 3. Push and hold the ignition switch until the engine turns OFF. Use this range for engine braking when descending very steep grades. In this range, the transmission will downshift 4. Wait approximately 30 seconds. for increased engine braking.
Page 338: Active Noise Cancellation
336 STARTING AND OPERATING NOTE: The torque converter clutch will not engage until WARNING! the engine and/or transmission is warm (usually after 1 to 3 miles [2 to 5 km] of driving). Because the engine speed is Continued operation with reduced assist could pose a higher when the torque converter clutch is not engaged, it safety risk to yourself and others.
Page 339: Stop/Start System - If Equipped
STARTING AND OPERATING 337 • The shifter must be in a forward gear and the brake STOP/START SYSTEM — IF EQUIPPED pedal depressed. The Stop/Start function is developed to reduce fuel con- sumption. The system will stop the engine automatically The engine will shut down, the tachometer will move to during a vehicle stop if the required conditions are met.
Page 340: To Start The Engine While In Auto Stop/Start
338 STARTING AND OPERATING • Cabin heating or cooling is in process and an acceptable To Start The Engine While In Auto Stop/Start cabin temperature has not been achieved. While in a forward gear, the engine will start when the •...
Page 341: To Manually Turn Off The Stop/Start System
STARTING AND OPERATING 339 To Manually Turn Off The Stop/Start System 4. The STOP/START system will reset itself back to an ON condition every time the ignition is turned off and back Automatic Shutdown This vehicle is equipped with an automatic shutdown feature.
Page 342: To Manually Turn On The Stop/Start System
340 STARTING AND OPERATING NOTE: If the vehicle is left in the ACC or RUN (engine not SPEED CONTROL — IF EQUIPPED running) position and the transmission is in PARK, the When engaged, the Speed Control takes over accelerator system will automatically time out (shut down) after an operations at speeds greater than 25 mph (40 km/h).
Page 343: To Activate
STARTING AND OPERATING 341 NOTE: In order to ensure proper operation, the Speed WARNING! Control System has been designed to shut down if multiple Speed Control functions are operated at the same time. If Leaving the Speed Control system on when not in use this occurs, the Speed Control System can be reactivated by is dangerous.
Page 344 342 STARTING AND OPERATING in “Multimedia” for more information. The speed incre- The driver’s preferred units can be selected through the ment shown is dependant on the chosen speed unit of U.S. Uconnect system if equipped. Refer to ”Uconnect Settings” (mph) or Metric (km/h): in “Multimedia”...
Page 345: To Accelerate For Passing
STARTING AND OPERATING 343 To Accelerate For Passing ACC will allow you to keep cruise control engaged in light to moderate traffic conditions without the constant need to Press the accelerator as you would normally. When the reset your cruise control. ACC utilizes a radar sensor and a pedal is released, the vehicle will return to the set speed.
Page 346 344 STARTING AND OPERATING NOTE: Normal (Fixed Speed) Cruise Control will not react WARNING! (Continued) to preceding vehicles. Always be aware of the mode • Cannot take street, traffic, and weather conditions selected. into account, and may be limited upon adverse You can change the mode by using the Cruise Control sight distance conditions.
Page 347: Adaptive Cruise Control (Acc) Operation
STARTING AND OPERATING 345 Adaptive Cruise Control (ACC) Operation NOTE: Any chassis/suspension or tire size modifications to the vehicle will effect the performance of the Adaptive The speed control buttons (located on the right side of the Cruise Control and Forward Collision Warning System. steering wheel) operates the ACC system.
Page 348: To Activate/Deactivate
346 STARTING AND OPERATING • When the driver door is open at low speed. • When the driver seat belt is unbuckled at low speed. To Activate/Deactivate Push and release the Adaptive Cruise Control (ACC) on/off button. The ACC menu in the instrument cluster displays “ACC Ready.”...
Page 349: To Cancel
STARTING AND OPERATING 347 • The gear selector is removed from the DRIVE position. If the system is set when the vehicle speed is below 20 mph (32 km/h), the set speed shall be defaulted to 20 mph • The Electronic Stability Control/Traction Control Sys- (32 km/h).
Page 350: To Vary The Speed Setting
348 STARTING AND OPERATING NOTE: The driver’s preferred units can be selected through the Uconnect Settings if equipped. Refer to “Uconnect Set- • If your vehicle stays at standstill for longer than two tings” in “Multimedia” for more information. The speed seconds, then the driver will either have to push the RES increment shown is dependant on the chosen speed unit of (resume) button, or apply the accelerator pedal to reen-...
Page 351 STARTING AND OPERATING 349 • If the button is continually pushed, the set speed will To Decrease Speed continue to decrease in 10 km/h decrements until the While ACC is set, the set speed can be decreased by button is released. The decrease in set speed is reflected pushing the SET (-) button.
Page 352: Setting The Following Distance In Acc
350 STARTING AND OPERATING speed. When driving up hill and down hill, the ACC system will cancel if the braking temperature exceeds normal range (overheated). Setting The Following Distance In ACC The specified following distance for ACC can be set by varying the distance setting between four bars (longest), three bars (long), two bars (medium) and one bar (short).
Page 353 STARTING AND OPERATING 351 Distance Setting 2 Bars (Medium) Distance Setting 1 Bar (Short) To increase the distance setting, push the Distance Setting — Increase button and release. Each time the button is pushed, the distance setting increases by one bar (longer). To decrease the distance setting, push the Distance Setting —...
Page 354: Overtake Aid
352 STARTING AND OPERATING Indicator” icon, and the system adjusts vehicle speed automatically to maintain the distance setting, regardless of the set speed. The vehicle will then maintain the set distance until: • The vehicle ahead accelerates to a speed above the set speed.
Page 355: Acc Operation At Stop
STARTING AND OPERATING 353 ACC Operation At Stop WARNING! In the event that the ACC system brings your vehicle to a When the ACC system is resumed, the driver must standstill while following a target vehicle, if the target ensure that there are no pedestrians, vehicles or objects vehicle starts moving within two seconds of your vehicle in the path of the vehicle.
Page 356: Display Warnings And Maintenance
354 STARTING AND OPERATING Push the SET (+) or the SET (-) button (located on the Display Warnings And Maintenance steering wheel) and the following will display in the “Wipe Front Radar Sensor In Front Of Vehicle” instrument cluster display: Warning ACC SET The “ACC/FCW Unavailable Wipe Front Radar Sensor”...
Page 357 STARTING AND OPERATING 355 If weather conditions are not a factor, the driver should NOTE: If the “ACC/FCW Unavailable Wipe Front Radar examine the sensor. It may require cleaning or removal of Sensor” message occurs frequently (e.g. more than once on an obstruction.
Page 358: Precautions While Driving With Acc
356 STARTING AND OPERATING If weather conditions are not a factor, the driver should Precautions While Driving With ACC examine the windshield and the camera located on the In certain driving situations, ACC may have detection back side of the inside rear view mirror. They may require issues.
Page 359 STARTING AND OPERATING 357 NOTE: On tight turns ACC performance may be limited. Offset Driving Condition Example Turns And Bends Turn Or Bend Example When driving on a curve with ACC engaged, the system may decrease the vehicle speed and acceleration for stabil- ity reasons, with no target vehicle detected.
Page 360 358 STARTING AND OPERATING Using ACC On Hills Lane Changing When driving on hills, ACC may not detect a vehicle in ACC may not detect a vehicle until it is completely in the your lane. Depending on the speed, vehicle load, traffic lane in which you are traveling.
Page 361 STARTING AND OPERATING 359 Narrow Vehicles Stationary Objects And Vehicles Some narrow vehicles traveling near the outer edges of the ACC does not react to stationary objects and stationary lane or edging into the lane are not detected until they have vehicles.
Page 362: General Information
360 STARTING AND OPERATING General Information To change between the different control modes, push the Adaptive Cruise Control (ACC) on/off button which turns This vehicle has systems that operate on radio frequency the ACC and the Normal (Fixed Speed) Cruise Control off. that comply with Part 15 of the Federal Communications Pushing the Normal (Fixed Speed) Cruise Control on/off Commission (FCC) rules and with Industry Canada Stan-...
Page 363 STARTING AND OPERATING 361 set a message “CRUISE CONTROL SET TO MPH (km/h)” Metric Speed (km/h) will appear indicating what speed was set. This light will • Pushing the SET (+) button once will result in a 1 km/h turn on when the system is turned on via the on/off increase in set speed.
Page 364: Parksense Rear Park Assist - If Equipped
362 STARTING AND OPERATING • If the button is continually pushed, the set speed will • The braking temperature exceeds normal range (over- continue to decrease in 5 mph decrements until the heated). button is released. The decrease in set speed is reflected •...
Page 365 STARTING AND OPERATING 363 • The automatic braking function can be enabled/ Automatic Transmission, the vehicle brakes may be auto- matically applied and released when performing a reverse disabled from the Customer-Programmable Features parking maneuver if the system detects a possible collision section of the Uconnect System.
Page 366: Parksense Sensors
364 STARTING AND OPERATING ParkSense can be active only when the gear selector is in REVERSE. If ParkSense is enabled at this gear selector position, the system will remain active until the vehicle speed is increased to approximately 7 mph (11 km/h) or above.
Page 367: Parksense Display
STARTING AND OPERATING 365 The ParkSense Warning screen is located within the instru- If an obstacle is detected in the left and/or right rear ment cluster display. It provides visual warnings to indi- region, the display will show a single flashing arc in the left cate the distance between the rear fascia/bumper and the and/or right rear region and will produce a fast sound detected obstacle.
Page 368 366 STARTING AND OPERATING Slow Tone/Solid Arc Slow Tone/Solid Arc...
Page 369 STARTING AND OPERATING 367 Fast Tone/Flashing Arc Fast Tone/Flashing Arc...
Page 370 368 STARTING AND OPERATING The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: Continuous Tone/Flashing Arc...
Page 371 STARTING AND OPERATING 369 WARNING ALERTS Rear Dis- Greater 79-59 inches 59-47 inches 47-39 inches 39-25 inches 25-12 inches Less than tance than (200-150 cm) (150-120 cm) (120-100 cm) (100-65 cm) (65-30 cm) 12 inches (in/cm) 79 inches (30 cm) (200 cm) Arcs —...
Page 372: Enabling And Disabling Parksense
370 STARTING AND OPERATING Enabling And Disabling ParkSense system is disabled, the instrument cluster display will show the “PARKSENSE OFF” message for as long as the ParkSense can be enabled and disabled with the ParkSense vehicle is in REVERSE. switch, located on the switch panel below the Uconnect display.
Page 373: Cleaning The Parksense System
STARTING AND OPERATING 371 a faulted condition, the instrument cluster display will ParkSense System Usage Precautions show the PARKSENSE UNAVAILABLE WIPE REAR SEN- NOTE: SORS or PARKSENSE UNAVAILABLE SERVICE RE- • Ensure that the rear bumper is free of snow, ice, mud, QUIRED message for five seconds while the vehicle is in dirt and debris to keep the ParkSense system operating REVERSE.
Page 374 372 STARTING AND OPERATING obstacle behind the fascia/bumper, or it could provide a WARNING! (Continued) false indication that an obstacle is behind the fascia/ • Before using ParkSense, it is strongly recommended bumper. that the ball mount and hitch ball assembly is •...
Page 375: Parksense Front And Rear Park Assist - If Equipped
STARTING AND OPERATING 373 • Automatic brakes will not be available if there is a CAUTION! (Continued) faulted condition detected with the ParkSense Park obstacle is detected. It is recommended that the Assist system or the Braking System Module. driver looks over his/her shoulder when using •...
Page 376: Parksense Sensors
374 STARTING AND OPERATING NOTE: ParkSense Sensors • The driver is always responsible for controlling the The four ParkSense sensors, located in the rear fascia/bumper, vehicle. monitor the area behind the vehicle that is within the sensors’ field of view. The sensors can detect obstacles from approxi- •...
Page 377: Parksense Visual Alert
STARTING AND OPERATING 375 The six ParkSense sensors, located in the front fascia/ ParkSense Display bumper, monitor the area in front of the vehicle that is Rear Park Assist within the sensors’ field of view. The sensors can detect When the vehicle is in REVERSE and an obstacle has been obstacles from approximately 12 inches (30 cm) up to 47 in detected, the warning display will turn ON indicating the (120 cm) from the front fascia/bumper in the horizontal...
Page 378 376 STARTING AND OPERATING If an obstacle is detected in the left and/or right rear region, the display will show a single flashing arc in the left and/or right rear region and will produce a fast sound tone. As the vehicle moves closer to the obstacle, the display will show the single arc moving closer to the vehicle and the tone will change from fast to continuous.
Page 379 STARTING AND OPERATING 377 Slow Tone/Solid Arc Fast Tone/Flashing Arc...
Page 380 378 STARTING AND OPERATING Fast Tone/Flashing Arc Continuous Tone/Flashing Arc The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle:...
Page 381 STARTING AND OPERATING 379 WARNING ALERTS Rear Dis- Greater 79-59 inches 59-47 inches 47-39 inches 39-25 inches 25-12 inches Less than tance than (200-150 cm) (150-120 cm) (120-100 cm) (100-65 cm) (65-30 cm) 12 inches (inches/cm) 79 inches (30 cm) (200 cm) Arcs —...
Page 382 380 STARTING AND OPERATING Front Park Assist When the vehicle is in DRIVE the ParkSense Warning screen will be displayed when an obstacle is detected. The system will indicate a detected obstacle by showing a single arc in one or more regions based on the obstacle’s distance and location relative to the vehicle.
Page 383 STARTING AND OPERATING 381 No Tone/Flashing Arc Fast Tone/Flashing Arc...
Page 384 382 STARTING AND OPERATING The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: Continuous Tone/Flashing Arc...
Page 385 STARTING AND OPERATING 383 WARNING ALERTS Front Distance Greater than 47-39 inches 39-25 inches 25-12 inches Less than (inches/cm) 47 inches (120 cm) (120-100 cm) (100-65 cm) (65-30 cm) 12 inches (30 cm) Arcs — Left None None None 2nd Flashing 1st Flashing Arcs —...
Page 386: Enabling And Disabling Parksense
384 STARTING AND OPERATING Enabling And Disabling ParkSense system is disabled, the instrument cluster display will show the “PARKSENSE OFF” message for as long as the ParkSense can be enabled and disabled with the ParkSense vehicle is in REVERSE. switch, located on the switch panel below the Uconnect display.
Page 387: Cleaning The Parksense System
STARTING AND OPERATING 385 show a PARKSENSE UNAVAILABLE WIPE REAR SEN- If the PARKSENSE UNAVAILABLE SERVICE RE- SORS , PARKSENSE UNAVAILABLE WIPE FRONT SEN- QUIRED message appears in the instrument cluster dis- SORS or PARKSENSE UNAVAILABLE SERVICE RE- play, see an authorized dealer. QUIRED pop up message for five seconds.
Page 388 386 STARTING AND OPERATING • ParkSense, when on, will reduce the volume of the radio WARNING! when it is sounding a tone. • Drivers must be careful when backing up even when • Clean the ParkSense sensors regularly, taking care not to using ParkSense.
Page 389: Parksense Active Park Assist System - If Equipped
STARTING AND OPERATING 387 ParkSense Active Park Assist system is capable of maneu- CAUTION! vering a vehicle into a parallel or a perpendicular parking • ParkSense is only a parking aid and it is unable to space on either side (i.e., driver side or passenger side). recognize every obstacle, including small obstacles.
Page 390: Enabling And Disabling The Parksense Active Park Assist System
388 STARTING AND OPERATING The system will also continuously perform the dynamic To disable the ParkSense Active Park Assist system, push vehicle calibration to account for differences such as the ParkSense Active Park Assist switch again (LED turns over or under inflated tires and new tires. off).
Page 391: Parallel Parking Space Assistance Operation/Display
STARTING AND OPERATING 389 system will cancel and the instrument cluster display will When pushed, the LED on the ParkSense Active Park instruct the driver to complete the maneuver manually. Assist switch will blink momentarily, and then the LED will turn OFF if any of the above conditions are not The ParkSense Active Park Assist system will only operate present.
Page 392 390 STARTING AND OPERATING • The driver is responsible to ensure that the selected parking space is suitable for the maneuver and free/ clear of anything that may be overhanging or protruding into the parking space (e.g., ladders, tailgates, etc. from surrounding objects/vehicles).
Page 393 STARTING AND OPERATING 391 When an available parking space has been found, and the Once the vehicle is in position, you will be instructed to vehicle is not in position, you will be instructed to move stop the vehicle’s movement and remove your hands from forward to position the vehicle for a parallel parking the steering wheel.
Page 394 392 STARTING AND OPERATING Once the vehicle is at a standstill with your hands removed When the driver places the gear selector into the REVERSE from the steering wheel, you will be instructed to place the position, the system may instruct the driver to wait for gear selector into the REVERSE position.
Page 395 STARTING AND OPERATING 393 • The ParkSense Active Park Assist system will allow a The system will then instruct the driver to check their surroundings and move backward. maximum of six shifts between DRIVE or REVERSE. If the maneuver cannot be completed within six shifts, the system will cancel and the instrument cluster display will instruct the driver to complete the maneuver manu- ally.
Page 396 394 STARTING AND OPERATING When the vehicle has reached the end of its backward Once the vehicle is in a standstill condition, the driver will movement, the system will instruct the driver to check be instructed to place the gear selector into the DRIVE their surroundings and stop the vehicle’s movement.
Page 397 STARTING AND OPERATING 395 When the driver places the gear selector into the DRIVE The system will then instruct the driver to check their position, the system may instruct the driver to wait for surroundings and move forward. steering to complete. Check Surroundings —...
Page 398 396 STARTING AND OPERATING When the vehicle has reached the end of its forward Once the vehicle is in a standstill condition, the driver will movement, the system will instruct the driver to check be instructed to place the gear selector into the REVERSE their surroundings and stop the vehicle’s movement.
Page 399 STARTING AND OPERATING 397 When the driver places the gear selector into the REVERSE The system will then instruct the driver to check their position, the system may instruct the driver to wait for surroundings and move backward. steering to complete. Check Surroundings —...
Page 400: Perpendicular Parking Space Assistance Operation/Display
398 STARTING AND OPERATING Your vehicle is now in the parallel park position. When the Perpendicular Parking Space Assistance maneuver is complete, the driver will be instructed to Operation/Display check the vehicle’s parking position. If the driver is satis- When the ParkSense Active Park Assist system is enabled, fied with the vehicle position, they should shift to PARK.
Page 401 STARTING AND OPERATING 399 • The driver needs to make sure that the selected parking space for the maneuver remains free and clear of any obstructions (e.g. pedestrians, bicycles, etc.). • The driver is responsible to ensure that the selected parking space is suitable for the maneuver and free/ clear of anything that may be overhanging or protruding into the parking space (e.g., ladders, tailgates, etc.
Page 402 400 STARTING AND OPERATING When an available parking space has been found, and the Once the vehicle is in position, you will be instructed to vehicle is not in position, you will be instructed to move stop the vehicle’s movement and remove your hands from forward to position the vehicle for a perpendicular parking the steering wheel.
Page 403 STARTING AND OPERATING 401 Once the vehicle is at a standstill with your hands removed When the driver places the gear selector into the REVERSE from the steering wheel, you will be instructed to place the position, the system may instruct the driver to wait for gear selector into the REVERSE position.
Page 404 402 STARTING AND OPERATING • The ParkSense Active Park Assist system will allow a The system will then instruct the driver to check their surroundings and move backward. maximum of six shifts between DRIVE or REVERSE. If the maneuver cannot be completed within six shifts, the system will cancel and the instrument cluster display will instruct the driver to complete the maneuver manu- ally.
Page 405 STARTING AND OPERATING 403 When the vehicle has reached the end of its backward Once the vehicle is in a standstill condition, the driver will movement, the system will instruct the driver to check be instructed to place the gear selector into the DRIVE their surroundings and stop the vehicle’s movement.
Page 406 404 STARTING AND OPERATING When the driver places the gear selector into the DRIVE The system will then instruct the driver to check their position, the system may instruct the driver to wait for surroundings and move forward. steering to complete. Check Surroundings —...
Page 407 STARTING AND OPERATING 405 When the vehicle has reached the end of its forward Once the vehicle is in a standstill condition, the driver will movement, the system will instruct the driver to check be instructed to place the gear selector into the REVERSE their surroundings and stop the vehicle’s movement.
Page 408 406 STARTING AND OPERATING When the driver places the gear selector into the REVERSE The system will then instruct the driver to check their position, the system may instruct the driver to wait for surroundings and move backward. steering to complete. Check Surroundings —...
Page 409 STARTING AND OPERATING 407 Your vehicle is now in the perpendicular park position. WARNING! (Continued) When the maneuver is complete, the driver will be in- the ParkSense Active Park Assist system. Always structed to check the vehicle’s parking position. If the check carefully behind and in front of your vehicle, driver is satisfied with the vehicle position, they should look behind and in front of you, and be sure to check...
Page 410: Lanesense - If Equipped
408 STARTING AND OPERATING LANESENSE — IF EQUIPPED NOTE: When operating conditions have been met, the LaneSense system will monitor if the driver’s hands are on LaneSense Operation the steering wheel and provides an audible and visual The LaneSense system is operational at speeds above warning to the driver when the driver’s hands are not 37 mph (60 km/h) and below 112 mph (180 km/h).
Page 411: Lanesense Warning Message
STARTING AND OPERATING 409 To turn the LaneSense system on, push the LaneSense LaneSense Warning Message button (LED turns off). A “Lane Sense On” message is The LaneSense system will indicate the current lane drift shown in the instrument cluster display. condition through the instrument cluster display.
Page 412: 410 Starting And Operating
410 STARTING AND OPERATING marking has been detected and the system is ready to Left Lane Departure — Both Lane Lines Detected provide visual warnings in the instrument cluster • When the LaneSense system is ON, the lane lines turn display if an unintentional lane departure occurs.
Page 413 STARTING AND OPERATING 411 solid yellow. At this time torque is applied to the this time torque is applied to the steering wheel in the steering wheel in the opposite direction of the lane opposite direction of the lane boundary. •...
Page 414: Changing Lanesense Status
412 STARTING AND OPERATING Changing LaneSense Status After five seconds, this note will disappear. The ParkView Rear Back Up Camera is located on the rear of the vehicle The LaneSense system has settings to adjust the intensity of above the rear license plate. the torque warning and the warning zone sensitivity (Early/Medium/Late) that you can configure through the NOTE: The ParkView Rear Back Up Camera has program-...
Page 415 STARTING AND OPERATING 413 When the vehicle is shifted out of REVERSE (with camera When enabled, active guide lines are overlaid on the image delay turned on), the camera image will continue to be to illustrate the width of the vehicle and its projected displayed for up to 10 seconds after shifting out of RE- backup path based on the steering wheel position.
Page 416: Surround View Camera System - If Equipped
414 STARTING AND OPERATING will disappear. The Surround View Camera System is CAUTION! comprised of 4 sequential cameras located in the front • To avoid vehicle damage, ParkView should only be grille, rear liftgate and side mirrors. used as a parking aid. The ParkView camera is NOTE: The Surround View Camera System has program- unable to view every obstacle or object in your drive mable settings that may be selected through the Uconnect...
Page 417 STARTING AND OPERATING 415 Different colored zones indicate the distance to the rear of the vehicle. The following table shows the approximate distances for each zone: Zone Distance to the rear of the vehicle 0 - 1 ft (0 - 30 cm) Yellow 1 ft - 6.5 ft (30 cm - 2 m) Green...
Page 418 416 STARTING AND OPERATING NOTE: Front View • Front tires will be in image when the tires are turned. The Front view will show you what is immediately in front of the vehicle and • Due to wide angle cameras in mirror, the image will is always paired with the Top view of appear distorted.
Page 419: Refueling The Vehicle
STARTING AND OPERATING 417 • If the vehicle is in any gear other than REVERSE, press CAUTION! the “X” button. • To avoid vehicle damage, Surround View should NOTE: only be used as a parking aid. The Surround View • If snow, ice, mud, or any foreign substance builds up on camera is unable to view every obstacle or object in the camera lenses, clean the lenses, rinse with water, and your drive path.
Page 420 418 STARTING AND OPERATING WARNING! (Continued) • A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You could be burned. Always place gas containers on the ground while filling. CAUTION! To avoid fuel spillage and overfilling, do not “top off” the fuel tank after filling.
Page 421: Vehicle Loading
STARTING AND OPERATING 419 NOTE: rear axle systems (GAWR). Total load must be limited so GVWR and front and rear GAWR are not exceeded. • In certain cold conditions, ice may prevent the fuel filler door from opening. If this occurs, lightly push on the Payload fuel filler door around the perimeter to break the ice The payload of a vehicle is defined as the allowable load...
Page 422 420 STARTING AND OPERATING Rim Size vehicle may show that the GAWR of either the front or rear axles has been exceeded but the total load is within the This is the rim size that is appropriate for the tire size specified GVWR.
Page 423: Trailer Towing
STARTING AND OPERATING 421 TRAILER TOWING Gross Trailer Weight (GTW) In this section you will find safety tips and information on The GTW is the weight of the trailer plus the weight of all limits to the type of towing you can reasonably do with cargo, consumables and equipment (permanent or tempo- your vehicle.
Page 424 422 STARTING AND OPERATING Tongue Weight (TW) most popular on the market today and they are commonly used to tow small and medium sized trailers. The tongue weight is the downward force exerted on the hitch ball by the trailer. You must consider this as part of Weight-Distributing Hitch the load on your vehicle.
Page 425: Trailer Hitch Classification
STARTING AND OPERATING 423 Trailer Hitch Classification WARNING! (Continued) The following chart provides the industry standard for the • Weight Distributing Systems may not be compatible maximum trailer weight a given trailer hitch class can tow with Surge Brake Couplers. Consult with your hitch and should be used to assist you in selecting the correct and trailer manufacturer or a reputable Recreational trailer hitch for your intended towing condition.
Page 426: Trailer Towing Weights (Maximum Trailer Weight Ratings)
424 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. GCWR (Gross Max. GTW Engine/ Trailer Tow Max. Tongue Combined Frontal Area (Gross Trailer Transmission Package Weight Weight Rating)
Page 427: Vehicle Loading Chart
STARTING AND OPERATING 425 Vehicle Loading Chart EXAMPLE: • GVWR = 6005 lbs (2723 kg) Follow these steps to determine the total weight the vehicle can carry. • CURB = 4500 lbs (2041 kg) 1. Determine the cargo capacity of your vehicle. •...
Page 428 426 STARTING AND OPERATING Number Of Persons / Weight Of Occupants Max Cargo No Tongue Load, Max Cargo With Trailer Max Trailer Max Trailer 360 lb (136 kg) Tongue Load 1205 lbs (546 kg) – 360 lbs (136 kg) = 845 lbs (383 kg) 1205 lbs (546 kg) 845 lbs (383 kg)
Page 429: Trailer And Tongue Weight
STARTING AND OPERATING 427 Trailer And Tongue Weight NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional Never exceed the maximum tongue weight stamped on factory-installed options or dealer-installed options must your bumper or trailer hitch.
Page 430 428 STARTING AND OPERATING Maintenance” for the proper maintenance intervals. When WARNING! (Continued) towing a trailer, never exceed the GAWR or GCWR ratings. • Vehicles with trailers should not be parked on a grade. When parking, apply the parking brake on the WARNING! tow vehicle.
Page 431 STARTING AND OPERATING 429 • Check the trailer tires for proper tire inflation pressures WARNING! before trailer usage. • Do not connect trailer brakes to your vehicle’s hy- • Check for signs of tire wear or visible tire damage before draulic brake lines.
Page 432 430 STARTING AND OPERATING The Trailer Tow Package may include a four- and seven-pin wiring harness. Use a factory approved trailer harness and connector. NOTE: Do not cut or splice wiring into the vehicle’s wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector.
Page 433: Towing Tips
STARTING AND OPERATING 431 when towing. For increased engine braking on steep down- hill grades, select the LOW range. Electronic Speed Control — If Equipped • Do not use in hilly terrain or with heavy loads. • When using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed.
Page 434: Recreational Towing
432 STARTING AND OPERATING RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Condition Wheel OFF the Ground All Models Flat Tow NONE NOT ALLOWED Dolly Tow Front Rear NOT ALLOWED On Trailer NOTE: Recreational Towing — All Models •...
Page 435: Driving Tips
STARTING AND OPERATING 433 Recreational towing is allowed ONLY if the front wheels DRIVING TIPS are OFF the ground. This may be accomplished using a tow Driving On Slippery Surfaces dolly (front wheels off the ground) or vehicle trailer (all Information in this section will aid in safe controlled four wheels off the ground).
Page 436: Driving Through Water
434 STARTING AND OPERATING complete loss of vehicle control and stopping ability. To Flowing/Rising Water reduce this possibility, the following precautions should be observed: WARNING! 1. Slow down during rainstorms or when the roads are Do not drive on or across a road or path where water is slushy.
Page 437 STARTING AND OPERATING 435 WARNING! CAUTION! (Continued) • Do not exceed 5 mph (8 km/h) when driving through • Driving through standing water limits your vehicle’s standing water. This will minimize wave effects. traction capabilities. Do not exceed 5 mph (8 km/h) •...
Page 439 IN CASE OF EMERGENCY CONTENTS ▫ Jacking Instructions .....463 HAZARD WARNING FLASHERS ... .439 ▫...
Page 440 438 IN CASE OF EMERGENCY ENHANCED ACCIDENT RESPONSE SYSTEM (EARS) .......499 EVENT DATA RECORDER (EDR) .
Page 441: Hazard Warning Flashers
IN CASE OF EMERGENCY 439 HAZARD WARNING FLASHERS ASSIST AND 9–1–1 REARVIEW MIRROR — IF EQUIPPED The Hazard Warning flasher switch is located in the lower center area of the instrument panel. A single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the windshield.
Page 442 440 IN CASE OF EMERGENCY The Automatic Dimming Mirror feature can be turned on WARNING! or off using the Mirror Dimming Button on the mirror. ALWAYS obey traffic laws and pay attention to the road. Some Uconnect Access services, including 9-1-1 and Assist, will NOT work without an operable 1X(voice/data) or 3G(data) network connection.
Page 443 IN CASE OF EMERGENCY 441 someone who can help. Roadside Assistance will know 3. Once a connection between the vehicle and a 9-1-1 what vehicle you’re driving and its location. Additional operator is made, the 9-1-1 Call system may transmit the fees may apply for roadside Assistance.
Page 444 442 IN CASE OF EMERGENCY NOTE: WARNING! (Continued) • Your vehicle may be transmitting data as authorized operator. All occupants should exit the vehicle im- by the subscriber. mediately and move to a safe location. • Once a connection is made between the vehicle’s 9-1-1 •...
Page 445 IN CASE OF EMERGENCY 443 • An In-Vehicle Audio message will state “Vehicle device WARNING! (Continued) requires service. Please contact your dealer.” APPS AND SERVICES, AMONG OTHERS, WILL NOT OPERATE. WARNING! • Modifications to any part of the 9-1-1 Call system •...
Page 446 444 IN CASE OF EMERGENCY • The vehicle battery loses power or becomes discon- NOTE: nected during a vehicle crash. • Your vehicle may be transmitting data as authorized by • 1X(voice/data) or 3G(data) network and/or Global Po- the subscriber. sitioning Satellite signals are unavailable or obstructed.
Page 447: Bulb Replacement
IN CASE OF EMERGENCY 445 BULB REPLACEMENT Replacement Bulbs Interior Bulbs Lamps Bulb Number Center & Rear Dome Lamp LED (Serviced At Authorized Dealer) Center & Rear Reading Lamps LED (Serviced At Authorized Dealer) Front Door Courtesy Lamp LED (Serviced At Authorized Dealer) Front Header Reading Lamps –...
Page 448 446 IN CASE OF EMERGENCY Lamps Bulb Number Dedicated Daytime Running Lamp (If Equipped) LED (Serviced at Authorized Dealer) Front Turn Signal Lamp PWY24WNA (If Halogen Headlamp Equipped) PWY24WSV (If HID Headlamp Equipped) Side Marker Lamp Front Park Lamp PWY24WNA (If Bulb Equipped) LED (Serviced At Authorized Dealer) Front Fog Lamp H11LL...
Page 449: Replacing Exterior Bulbs
IN CASE OF EMERGENCY 447 Replacing Exterior Bulbs Halogen Headlamps Bi-Xenon High Intensity Discharge (HID) 1. Reach behind the headlamp housing to access the Headlamps — If Equipped headlamp bulb cap. The headlamps contain a type of high voltage discharge 2.
Page 450 448 IN CASE OF EMERGENCY 3. Firmly grasp the headlamp bulb socket assembly and 4. Disconnect the bulb from the electrical connector and rotate counterclockwise to remove from the housing. then connect the replacement bulb. Headlamp Bulb Socket Headlamp Bulb CAUTION! Do not touch the new bulb with your fingers.
Page 451 IN CASE OF EMERGENCY 449 6. Install the headlamp bulb cap in the headlamp housing 4. Install the front turn signal lamp socket assembly into and rotate clockwise to lock it in place. the housing, and rotate the front turn signal lamp socket clockwise to lock it in place.
Page 452 450 IN CASE OF EMERGENCY 2. Reach through the front fascia to fog lamp housing to access the bulb. 3. Rotate the front fog lamp socket counterclockwise, and remove the bulb and socket assembly from the front fog lamp housing. Front Side Marker Lamp Bulb Removal 3.
Page 453 IN CASE OF EMERGENCY 451 Rear Bodyside Mounted Taillamps CAUTION! 1. Raise the liftgate. Do not touch the new bulb with your fingers. Oil 2. Remove two torx head screws on bodyside lamp using contamination will severely shorten bulb life. If the a T30 screwdriver.
Page 454: Fuses
452 IN CASE OF EMERGENCY FUSES When a device does not work, you must check the electri- cal circuit inside the fuse for a break/melt. WARNING! Also, please be aware that when using power outlets for extended periods of time with the engine off may result in •...
Page 455: Fuse Location
IN CASE OF EMERGENCY 453 Fuse Location The fuses are grouped into a controller located in the engine compartment. Underhood Fuses The Power Distribution Center is located in the engine compartment near the battery. This center contains car- tridge fuses, mini-fuses, micro-fuses, circuit breakers and relays.
Page 456 454 IN CASE OF EMERGENCY Cavity Cartridge Fuse Blade Fuse Description 40 Amp Green – Power Locks – 20 Amp Yellow 30 Amp Pink – Starter 40 Amp Green – CBC Feed #2 (Exterior Lights #1) 25 Amp Clear – 2nd Row Folding Seats So- lenoid LT –...
Page 457 IN CASE OF EMERGENCY 455 Cavity Cartridge Fuse Blade Fuse Description – – Not Used – 15 Amp Blue Media Hub 1, 2/ Power Lumbar – – Not Used 20 Amp Blue – 30 Amp Pink – Power Liftgate Module 25 Amp Clear –...
Page 458 456 IN CASE OF EMERGENCY Cavity Cartridge Fuse Blade Fuse Description 30 Amp Pink – Driver Door Module 30 Amp Pink – Passenger Door Module – – Not Used 25 Amp Clear – RR Sliding Door Module 25 Amp Clear –...
Page 459 IN CASE OF EMERGENCY 457 Cavity Cartridge Fuse Blade Fuse Description – – Not Used 30 Amp Pink – Trailer Tow Receptacle — If Equipped – 20 Amp Yellow Rear Cargo APO – 20 Amp Yellow Trailer Tow Right Stop/ Turn —...
Page 460 458 IN CASE OF EMERGENCY Cavity Cartridge Fuse Blade Fuse Description – 20 Amp Yellow Horn – 10 Amp Red Heated Mirrors – If Equipped 30 Amp Pink – Rear Defroster (EBL) 20 Amp Blue – Trailer Tow Backup – 5 Amp Tan Overhead Console / RR –...
Page 461 IN CASE OF EMERGENCY 459 Cavity Cartridge Fuse Blade Fuse Description – – Not Used – – Not Used 20 Amp Blue – TT Park Lights — If Equipped 30 Amp Pink – Headlamp Washer Pump — If Equipped – –...
Page 462 460 IN CASE OF EMERGENCY Cavity Cartridge Fuse Blade Fuse Description F95B – 10 Amp Red USB Charge Port — Battery Power – 10 Amp Red Occupant Restraint Con- troller (ORC) (Airbag) – 10 Amp Red Occupant Restraint Con- troller (ORC) (Airbag) –...
Page 463: Jacking And Tire Changing - If Equipped
IN CASE OF EMERGENCY 461 JACKING AND TIRE CHANGING — IF EQUIPPED Jack And Spare Tire Location The jacking tools, spare tire and portable air compressor (if WARNING! equipped) or tire service kit (if equipped) are stowed behind an access panel on the left hand side of the vehicle. •...
Page 464: Equipment Removal
462 IN CASE OF EMERGENCY Equipment Removal 3. Remove Jack by turning the jack screw counterclockwise to collapse from storage area that is located behind the 1. Remove the access panel to the jacking equipment. tire. 2. Unlatch the Portable Air Compressor or Tire Service Kit if equipped.
Page 465: Jacking Instructions
IN CASE OF EMERGENCY 463 Jacking Instructions WARNING! WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the Carefully follow these tire changing warnings to help road to avoid being hit when operating the jack or prevent personal injury or damage to your vehicle: changing the wheel.
Page 466 464 IN CASE OF EMERGENCY Jack Warning Label Extending The Wrench 1. Loosen (but do not remove) the wheel lug nuts by CAUTION! turning them to the left one turn while the wheel is still Do not attempt to raise the vehicle by jacking on on the ground.
Page 467 IN CASE OF EMERGENCY 465 2. There are two jack engagement locations on each side of WARNING! the vehicle body. These locations are on the sill flange of the vehicle body. Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed.
Page 468 466 IN CASE OF EMERGENCY Front Jack Engaged Rear Jacking Location...
Page 469 IN CASE OF EMERGENCY 467 obtained to install the compact spare tire. Minimum tire lift provides maximum stability. WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire.
Page 470 468 IN CASE OF EMERGENCY nuts with wrench. After inflation, once the vehicle is lowered you will have a second opportunity to “torque” the lug nuts. 8. Inflate the tire to the prescribed pressure 60 psi (4.2 Bar) using the Portable Air Compressor or Tire Service Kit if equipped.
Page 471 IN CASE OF EMERGENCY 469 NOTE: Stow the foam tray and components in the cargo WARNING! area. A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided.
Page 472: Portable Air Compressor - If Equipped
470 IN CASE OF EMERGENCY Portable Air Compressor — If Equipped Portable Air Compressor Usage With Inflatable Spare Tire Your vehicle may be equipped with a Portable Air Com- pressor. Use the Portable Air Compressor located in the 1. Remove the Portable Air Compressor from the storage side compartment of the cargo area to inflate the inflatable location.
Page 473 IN CASE OF EMERGENCY 471 4. Uncoil the power plug and connect it the vehicles 12 7. Inflate the tire to 60 psi (4.2 Bar) recommended as per Volt power Outlet. the label on the wheel or if the vehicle equipped with the inflatable spare tire pressure indicated on the Tire and Loading information label lo-...
Page 474: Tire Service Kit For Inflating Tire - If Equipped
472 IN CASE OF EMERGENCY 10. Return the Portable Air Compressor to the foam tray Tire Service Kit And Components And Operation and secure it with the strap. Store the foam tray in the cargo area. WARNING! • Do not lift or carry the Portable Air Compressor by the hose.
Page 475 IN CASE OF EMERGENCY 473 Using The Mode Select Knob And Hoses Using The Power Button Your Tire Service Kit is equipped with the following Push and release the Power Button once symbols to indicate the air or sealant mode. to turn On the Tire Service Kit.
Page 476 474 IN CASE OF EMERGENCY 2. Verify that the valve stem (on the wheel with the WARNING! (Continued) deflated tire) is in a position that is near to the ground. provided. Failure to follow these warnings can result This will allow the Tire Service Kit Hose to reach the in injuries that are serious or fatal to you, your valve stem and keep the Tire Service Kit flat on the passengers, and others around you.
Page 477 IN CASE OF EMERGENCY 475 3. Uncoil the Power Plug and insert the plug into the 7. Turn the Mode Select Knob to Air Mode position. vehicle’s 12 Volt power outlet. NOTE: Do not fill inflatable spare tire with sealant. Refer to “Tire Service Kit” in this chapter for repairing tires.
Page 478: Road Tire Installation
476 IN CASE OF EMERGENCY 9. Inflate the tire to 60 psi (4.2 Bar) recommended as per 11. Remove the speed limit label sticker from the Tire the label on the wheel or if the vehicle Service Kit and place it on the center equipped with the inflatable spare of the steering wheel.
Page 479 IN CASE OF EMERGENCY 477 WARNING! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle has been lowered. Failure to follow this warning may result in serious injury. 5.
Page 480: Return Inflatable Spare Tire
478 IN CASE OF EMERGENCY 2. Install the remaining lug nuts with the cone shaped end Return Inflatable Spare Tire of the nut toward the wheel. Lightly tighten the lug To return Inflatable Spare Tire to its storage location. nuts. 1.
Page 481 IN CASE OF EMERGENCY 479 or nails) should not be removed from the tire. Tire Service Tire Service Kit And Components And Operation Kit can be used in outside temperatures down to approxi- mately -4°F (-20°C). This kit will provide a temporary tire seal, allowing you to drive your vehicle up to 100 miles (160 km) with a maximum speed of 50 mph (80 km/h).
Page 482 480 IN CASE OF EMERGENCY Using The Mode Select Knob And Hoses Using The Power Button Your Tire Service Kit is equipped with the following Push and release the Power Button once symbols to indicate the air or sealant mode. to turn On the Tire Service Kit.
Page 483 IN CASE OF EMERGENCY 481 • The Sealant Bottle is a one tire application use and needs WARNING! to be replaced after each use. Always replace these • Do not attempt to seal a tire on the side of the vehicle components immediately at your original equipment vehicle dealer.
Page 484 482 IN CASE OF EMERGENCY Sealing A Tire With Tire Service Kit WARNING! (Continued) Whenever You Stop To Use Tire Service Kit: in injuries that are serious or fatal to you, your passengers, and others around you. 1. Pull over to a safe location and turn on the vehicle’s •...
Page 485 IN CASE OF EMERGENCY 483 3. Remove the cap from the valve stem and then screw the Injecting Tire Service Kit Sealant Into The Deflated Tire: fitting at the end of the Sealant Hose 1. Always start the vehicle before turning ON the Tire onto the valve stem.
Page 486 484 IN CASE OF EMERGENCY 3. After pushing the Power Button, the sealant (white 3. The Sealant Bottle may be empty due to previous use. fluid) will flow from the Sealant Call for assistance. Bottle through the Sealant Hose and If the sealant (white fluid) does flow through the Sealant into the tire.
Page 487 IN CASE OF EMERGENCY 485 If the tire does not inflate to at least 26 psi (1.8 Bar) 2. Remove the speed limit label from the Tire Service Kit pressure within 15 minutes: and place sticker on the steering wheel. •...
Page 488 486 IN CASE OF EMERGENCY 3. Remove the cap from the valve stem, and then screw WARNING! the fitting at the end of the Sealant Hose onto the valve stem. Tire Service Kit is not a permanent flat tire repair. Have the tire inspected and repaired or replaced after using Tire Service Kit.
Page 489 IN CASE OF EMERGENCY 487 6. Turn the Mode Select Knob and turn to the Air Mode NOTE: If the tire becomes over-inflated, push the Deflation position. Button to reduce the tire pressure to the recommended inflation pressure before continuing. 2.
Page 490 488 IN CASE OF EMERGENCY Sealant Bottle Replacement: 3. Remove the bottle cover. 1. Unwrap the power cord. 2. Unwrap the hose. Remove The Bottle Cover Unwrap The Hose...
Page 491 IN CASE OF EMERGENCY 489 4. Rotate the bottle up beyond vertical to release. 5. Pull the bottle away from the Compressor. Rotate The Bottle Up Remove The Bottle NOTE: • For sealant bottle installation, follow these steps reverse order. •...
Page 492: Jump-Starting
490 IN CASE OF EMERGENCY JUMP-STARTING Preparations For Jump-Start If your vehicle has a discharged battery it can be jump- The battery in your vehicle is located on the left side of the started using a set of jumper cables and a battery in another engine compartment.
Page 493 IN CASE OF EMERGENCY 491 WARNING! (Continued) • Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive. Keep open flames or sparks away from the battery. 1. Set the parking brake, shift the automatic transmission into PARK and place the ignition to OFF.
Page 494: Jump-Starting Procedure
492 IN CASE OF EMERGENCY Jump-Starting Procedure 4. Connect the opposite end of the negative (-) jumper cable to the negative post near the windshield cowl WARNING! (exposed metal part of the discharged vehicle’s engine). Failure to follow this jump starting procedure could WARNING! result in personal injury or property damage due to battery explosion.
Page 495: Refueling In Emergency
IN CASE OF EMERGENCY 493 3. Disconnect the positive (+) end of the jumper cable from For more information on the Cap-Less Fuel System refer to the positive (+) post of the booster battery. “Refueling The Vehicle” in “Starting And Operating ” in this manual.
Page 496: Manual Park Release
494 IN CASE OF EMERGENCY WARNING! WARNING! (Continued) the vehicle before activating the Manual Park Release. You or others can be badly burned by hot engine If possible, you should apply the parking brake. Acti- coolant (antifreeze) or steam from your radiator. If you vating the Manual Park Release will allow your ve- see or hear steam coming from under the hood, do not hicle to roll away if it is not secured or properly...
Page 497: Freeing A Stuck Vehicle
IN CASE OF EMERGENCY 495 Follow these steps to activate the Manual Park Release: 3. Allow the tether to retract with the lever back to its original position. 1. Apply firm pressure to the brake pedal while seated in the driver’s seat. 4.
Page 498 496 IN CASE OF EMERGENCY NOTE: Push the ESC Off switch to place the Electronic CAUTION! Stability Control (ESC) system in Partial Off mode, before • Racing the engine or spinning the wheels may lead rocking the vehicle. Refer to “Electronic Brake Control” in “Safety”...
Page 499: Towing A Disabled Vehicle
IN CASE OF EMERGENCY 497 TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service. Towing Condition Wheel OFF The Ground ALL MODELS Flat Tow NONE NOT ALLOWED Wheel Lift Or Dolly Tow Front Rear NOT ALLOWED...
Page 500 498 IN CASE OF EMERGENCY If flatbed equipment is not available, this vehicle must towed with the front wheels OFF the ground (using a towing dolly, or wheel lift equipment with the front wheels raised). NOTE: Ensure that the Electric Park Brake is released, and remains released, while being towed.
Page 501 IN CASE OF EMERGENCY 499 CAUTION! (Continued) CAUTION! • Do not use sling-type equipment when towing. Ve- • Be applied parallel to the center line of the length of hicle damage may occur. the vehicle. • When securing the vehicle to a flatbed truck, do not •...
Page 503 SERVICING AND MAINTENANCE CONTENTS ▫ Windshield Wiper Blades ....517 SCHEDULED SERVICING ....503 ▫...
Page 504 502 SERVICING AND MAINTENANCE ▫ Body And Underbody Maintenance ..556 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES ....554 ▫...
Page 505: Scheduled Servicing
SERVICING AND MAINTENANCE 503 SCHEDULED SERVICING NOTE: Under no circumstances should oil change inter- vals exceed 10,000 miles (16,000 km), twelve months or 350 Your vehicle is equipped with an automatic oil change hours of engine run time, whichever comes first. The 350 indicator system.
Page 506: Maintenance Plan
504 SERVICING AND MAINTENANCE Maintenance Plan Required Maintenance Intervals Refer to the maintenance schedules on the following page for the required maintenance intervals. At Every Oil Change Interval As Indicated By Oil Change Indicator System: • Change oil and filter •...
Page 507 SERVICING AND MAINTENANCE 505 Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Additional Inspections Inspect the CV joints. Inspect front suspension, boot seals, tie rod ends, and replace if necessary. Inspect the brake linings, parking brake function. Inspect front accessory drive belt, tensioner, idler pul- ley, and replace if necessary Additional Maintenance...
Page 508: Heavy Duty Use Of The Vehicle
506 SERVICING AND MAINTENANCE Heavy Duty Use Of The Vehicle WARNING! Change Engine Oil at 4,000 miles (6,500 km) if the vehicle • You can be badly injured working on or around a is operated in a dusty and off road environment or is motor vehicle.
Page 509: Engine Compartment
SERVICING AND MAINTENANCE 507 ENGINE COMPARTMENT 3.6L Engine 1 — Engine Coolant Pressure Cap 5 — Power Distribution Center (Fuses) 2 — Engine Oil Fill 6 — Battery 3 — Brake Fluid Reservoir 7 — Engine Oil Dipstick 4 — Engine Air Cleaner 8 —...
Page 510: Checking Oil Level
508 SERVICING AND MAINTENANCE Checking Oil Level Adding Washer Fluid To assure proper engine lubrication, the engine oil must be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop. The best time to check the engine oil level is about five minutes after a fully warmed engine is shut OFF.
Page 511: Maintenance-Free Battery
SERVICING AND MAINTENANCE 509 To prevent freeze-up of your windshield washer system in WARNING! (Continued) cold weather, select a solution or mixture that meets or large amounts of water. Refer to “Jump-Starting exceeds the temperature range of your climate. This rating Procedure”...
Page 512: Dealer Service
510 SERVICING AND MAINTENANCE Engine Oil CAUTION! (Continued) • If a “fast charger” is used while the battery is in the Change Engine Oil — Gasoline Engine vehicle, disconnect both vehicle battery cables before Refer to “Scheduled Servicing” in this section for the connecting the charger to the battery.
Page 513 SERVICING AND MAINTENANCE 511 American Petroleum Institute (API) Engine Oil The engine oil filler cap also shows the recommended Identification Symbol engine oil viscosity for your engine. For information on engine oil filler cap location, refer to the “Engine Compart- ment”...
Page 514: Engine Oil Filter
512 SERVICING AND MAINTENANCE Disposing Of Used Engine Oil And Oil Filters WARNING! Care should be taken in disposing of used engine oil and The air induction system (air cleaner, hoses, etc.) can oil filters from your vehicle. Used oil and oil filters, provide a measure of protection in the case of engine indiscriminately discarded, can present a problem to the backfire.
Page 515 SERVICING AND MAINTENANCE 513 Refrigerant Recovery And Recycling — R–1234yf WARNING! R–1234yf Air Conditioning Refrigerant is a hydrofluo- • Use only refrigerants and compressor lubricants ap- roolefin (HFO) that is endorsed by the Environmental proved by the manufacturer for your air conditioning Protection Agency and is an ozone-friendly substance with system.
Page 516 514 SERVICING AND MAINTENANCE The cabin air filter is located in the fresh air inlet behind the 2. Open the glove compartment door partially, leaving glove compartment. Perform the following procedure to extra slack on the glove compartment tension tether. replace the filter: Detach the glove compartment tension tether by sliding the black tension tether clip down, and popping it out of...
Page 517 SERVICING AND MAINTENANCE 515 Cabin Air Filter Compartment Cover Fresh Air Inlet 1 — Compartment Cover 1 — Filter Cover 2 — Compartment Snap 2 — Retaining Tab 5. Pry up the lid of each individual compartment snap, 7. Remove the filter cover by prying back each of the and detach it from the rest of the snap.
Page 518: Body Lubrication
516 SERVICING AND MAINTENANCE Body Lubrication CAUTION! Locks and all body pivot points, including such items as The cabin air filter is identified with an arrow to seat tracks, door hinge pivot points and rollers, liftgate, indicate airflow direction through the filter. Failure to tailgate, decklid, sliding doors and hood hinges, should be properly install the filter will result in the need to lubricated periodically with a lithium based grease, such as...
Page 519: Windshield Wiper Blades
SERVICING AND MAINTENANCE 517 Windshield Wiper Blades The wiper blades and wiper arms should be inspected periodically, not just when wiper performance problems Clean the rubber edges of the wiper blades and the are experienced. This inspection should include the follow- windshield periodically with a sponge or soft cloth and a ing points: mild nonabrasive cleaner.
Page 520 518 SERVICING AND MAINTENANCE Front Wiper Blade Removal/Installation CAUTION! Do not allow the wiper arm to spring back against the glass without the wiper blade in place or the glass may be damaged. 1. Lift the wiper arm to raise the wiper blade off of the glass, until the wiper arm is in the full up position.
Page 521 SERVICING AND MAINTENANCE 519 2. To disengage the wiper blade from the wiper arm, flip 3. With the wiper blade disengaged, remove the wiper up the release tab on the wiper blade and while holding blade from the wiper arm by holding the wiper arm the wiper arm with one hand, slide the wiper blade with one hand and separating the wiper blade from the down towards the base of the wiper arm.
Page 522 520 SERVICING AND MAINTENANCE Installing The Front Wipers NOTE: The rear wiper arm cannot be fully raised off the glass unless the wiper arm pivot cap is unsnapped first. 1. Lift the wiper arm off of the glass, until the wiper arm is Attempting to fully raise the rear wiper arm without in the full up position.
Page 523 SERVICING AND MAINTENANCE 521 NOTE: Resistance will be accompanied by an audible snap. 4. Still grasping the bottom end of the wiper blade, move the wiper blade upward and away from the wiper arm to disengage. Wiper Blade In Folded Out Position 1 —...
Page 524: Exhaust System
522 SERVICING AND MAINTENANCE Installing The Rear Wiper have an authorized technician inspect the complete ex- haust system and adjacent body areas for broken, dam- 1. Lift the rear wiper arm pivot cap away from the glass to aged, deteriorated, or mispositioned parts. Open seams or allow the rear wiper blade to be raised off of the glass.
Page 525 SERVICING AND MAINTENANCE 523 NOTE: Intentional tampering with emissions control sys- CAUTION! tems can result in civil penalties being assessed against • The catalytic converter requires the use of unleaded you. fuel only. Leaded gasoline will destroy the effective- In unusual situations involving grossly malfunctioning ness of the catalyst as an emissions control device engine operation, a scorching odor may suggest severe and and may seriously reduce engine performance and...
Page 526: Cooling System
524 SERVICING AND MAINTENANCE Cooling System WARNING! (Continued) • You or others can be badly burned by hot engine WARNING! coolant (antifreeze) or steam from your radiator. If • Turn vehicle off and disconnect the fan motor lead you see or hear steam coming from under the hood, before working near the radiator cooling fan.
Page 527 SERVICING AND MAINTENANCE 525 Cooling System — Drain, Flush And Refill CAUTION! (Continued) NOTE: Some vehicles require special tools to add coolant Additive Technology (OAT) engine coolant is differ- properly. Failure to fill these systems properly could lead to ent and should not be mixed with Hybrid Organic severe internal engine damage.
Page 528 526 SERVICING AND MAINTENANCE • Use only high purity water such as distilled or deionized Adding Coolant water when mixing the water/engine coolant (anti- Your vehicle has been built with an improved engine freeze) solution. The use of lower quality water will coolant (OAT coolant conforming to MS.90032) that allows reduce the amount of corrosion protection in the engine extended maintenance intervals.
Page 529 SERVICING AND MAINTENANCE 527 Cooling System Pressure Cap Disposal Of Used Coolant The cap must be fully tightened to prevent loss of engine Used ethylene glycol-based coolant (antifreeze) is a regu- coolant (antifreeze), and to ensure that engine coolant lated substance requiring proper disposal. Check with your (antifreeze) will return to the radiator from the coolant local authorities to determine the disposal rules for your recovery tank.
Page 530 528 SERVICING AND MAINTENANCE • Maintain engine coolant (antifreeze) concentration at a Points To Remember minimum of 50% OAT coolant (conforming to NOTE: When the vehicle is stopped after a few miles/ MS.90032) and distilled water for proper corrosion pro- kilometers of operation, you may observe vapor coming tection of your engine which contains aluminum com- from the front of the engine compartment.
Page 531: Brake System
SERVICING AND MAINTENANCE 529 Brake System checked when pads are replaced. However, low fluid level may be caused by a leak and a checkup may be needed. In order to assure brake system performance, all brake system components should be inspected periodically. Refer Use only manufacturer’s recommended brake fluid.
Page 532: Automatic Transmission
530 SERVICING AND MAINTENANCE WARNING! (Continued) CAUTION! • Overfilling the brake fluid reservoir can result in Using a transmission fluid other than the manufactur- spilling brake fluid on hot engine parts, causing the er’s recommended fluid may cause deterioration in brake fluid to catch fire.
Page 533: Raising The Vehicle
SERVICING AND MAINTENANCE 531 Fluid Level Check Fluid And Filter Changes The fluid level is preset at the factory and does not require Under normal operating conditions, the fluid installed at adjustment under normal operating conditions. Routine the factory will provide satisfactory lubrication for the life fluid level checks are not required;...
Page 534 532 SERVICING AND MAINTENANCE Tire Markings NOTE: • P (Passenger) — Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European — Metric tire sizing is based on European design standards.
Page 535 SERVICING AND MAINTENANCE 533 Tire Sizing Chart EXAMPLE: Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 LT P = Passenger car tire size based on U.S. design standards, or ..blank..= Passenger car tire based on European design standards, or LT = Light truck tire based on U.S.
Page 536 534 SERVICING AND MAINTENANCE EXAMPLE: H = Speed Symbol – A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under cer- tain operating conditions – The maximum speed corresponding to the speed symbol should only be achieved under specified operating condi- tions (i.e., tire pressure, vehicle loading, road conditions, and posted speed limits) Load Identification: Absence of the following load identification symbols on the sidewall of the tire indicates a Standard Load (SL) tire:...
Page 537 SERVICING AND MAINTENANCE 535 Tire Identification Number (TIN) the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the The TIN may be found on one or both sides of the tire; outboard side, then you will find it on the inboard side of however, the date code may only be on one side.
Page 538 536 SERVICING AND MAINTENANCE Tire Terminology And Definitions Term Definition B-Pillar The vehicle B-Pillar is the structural member of the body located be- hind the front door. Cold Tire Inflation Pressure Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting for a minimum of three hours.
Page 539 SERVICING AND MAINTENANCE 537 Tire Loading And Tire Pressure NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door. Example Tire Placard Location (B-Pillar) Example Tire Placard Location (Door)
Page 540 538 SERVICING AND MAINTENANCE Tire And Loading Information Placard Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire and Loading Information placard in “Vehicle Loading”...
Page 541 SERVICING AND MAINTENANCE 539 Steps For Determining Correct Load Limit— Metric Example For Load Limit (1) Locate the statement “The combined weight of For example, if “XXX” amount equals 635 kg and there will occupants and cargo should never exceed XXX kg or be five 68 kg passengers in your vehicle, the amount of XXX lbs.”...
Page 542 540 SERVICING AND MAINTENANCE WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the rec- ommended load capacity for your vehicle. Never over- load them.
Page 543: Tires - General Information
SERVICING AND MAINTENANCE 541 Tires — General Information WARNING! (Continued) Tire Pressure • Overinflated or underinflated tires can affect vehicle handling and can fail suddenly, resulting in loss of Proper tire inflation pressure is essential to the safe and vehicle control. satisfactory operation of your vehicle.
Page 544 542 SERVICING AND MAINTENANCE Fuel Economy CAUTION! Underinflated tires will increase tire rolling resistance After inspecting or adjusting the tire pressure, always resulting in higher fuel consumption. reinstall the valve stem cap. This will prevent moisture Tread Wear and dirt from entering the valve stem, which could damage the valve stem.
Page 545 SERVICING AND MAINTENANCE 543 pressure should be increased by 3 psi (21 kPa), which Radial Ply Tires equals 1 psi (7 kPa) for every 12°F (7°C) for this outside temperature condition. WARNING! Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) Combining radial ply tires with other types of tires on during operation.
Page 546 544 SERVICING AND MAINTENANCE Run Flat Tires — If Equipped Refer to “Freeing A Stuck Vehicle” in “In Case Of Emer- gency” for further information. Run Flat tires allow you the capability to drive 50 miles (80 km) at 50 mph (80 km/h) after a rapid loss of inflation WARNING! pressure.
Page 547 SERVICING AND MAINTENANCE 545 Life Of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style. • Tire pressure - Improper cold tire inflation pressures can cause uneven wear patterns to develop across the tire tread.
Page 548 546 SERVICING AND MAINTENANCE Keep dismounted tires in a cool, dry place with as little It is recommended you contact your authorized tire dealer exposure to light as possible. Protect tires from contact with or original equipment dealer with any questions you may oil, grease, and gasoline.
Page 549: Tire Types
SERVICING AND MAINTENANCE 547 Summer Or Three Season Tires — If Equipped WARNING! (Continued) Summer tires provide traction in both wet and dry condi- • Failure to equip your vehicle with tires having ad- tions, and are not intended to be driven in snow or on ice. equate speed capability can result in sudden tire If your vehicle is equipped with Summer tires, be aware failure and loss of vehicle control.
Page 550: Spare Tires - If Equipped
548 SERVICING AND MAINTENANCE Snow Tires Spare Tires — If Equipped Some areas of the country require the use of snow tires NOTE: For vehicles equipped with Tire Service Kit instead during the Winter. Snow tires can be identified by a of a spare tire, please refer to “Tire Service Kit”...
Page 551 SERVICING AND MAINTENANCE 549 spare by looking at the spare tire description on the Tire WARNING! (Continued) and Loading Information Placard located on the driver’s needs to be replaced. Be sure to follow the warnings, side door opening or on the sidewall of the tire. Compact which apply to your spare.
Page 552: Wheel And Wheel Trim Care
550 SERVICING AND MAINTENANCE use spare wheel. This label contains the driving limitations WARNING! for this spare. This tire may look like the original equipped tire on the front or rear axle of your vehicle, but it is not. Compact and Collapsible spares are for temporary Installation of this limited use spare tire affects vehicle emergency use only.
Page 553 SERVICING AND MAINTENANCE 551 and to prevent corrosion. Wash wheels with the same soap wheel cleaning chemicals and equipment to prevent dam- solution recommended for the body of the vehicle. age to the wheels. Mopar Wheel Treatment or Mopar Chrome Cleaner or their equivalent is recommended or Your wheels are susceptible to deterioration caused by salt, select a non-abrasive, non-acidic cleaner for aluminum or sodium chloride, magnesium chloride, calcium chloride,...
Page 554: Tire Chains (Traction Devices)
552 SERVICING AND MAINTENANCE Dark Vapor Or Black Satin Chrome Wheels WARNING! CAUTION! Using tires of different size and type (M+S, Snow) between front and rear axles can cause unpredictable If your vehicle is equipped with Dark Vapor or Black handling.
Page 555: Tire Rotation Recommendations
SERVICING AND MAINTENANCE 553 Refer to the “Scheduled Servicing” for the proper mainte- CAUTION! (Continued) nance intervals. The reasons for any rapid or unusual wear • Observe the traction device manufacturer’s instruc- should be corrected prior to rotation being performed. tions on the method of installation, operating speed, The suggested rotation method is the “forward cross”...
Page 556: Department Of Transportation Uniform Tire Quality Grades
554 SERVICING AND MAINTENANCE DEPARTMENT OF TRANSPORTATION UNIFORM on wet pavement, as measured under controlled condi- TIRE QUALITY GRADES tions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction The following tire grading categories were established performance.
Page 557: Storing The Vehicle
SERVICING AND MAINTENANCE 555 • Clean and protect the painted parts by applying protec- Vehicle Safety Standard No. 109. Grades B and A repre- sent higher levels of performance on the laboratory test tive waxes. wheel, than the minimum required by law. •...
Page 558: Bodywork
556 SERVICING AND MAINTENANCE NOTE: When the vehicle has not been started or driven for The following maintenance recommendations will enable at least 30 days, an Extended Park Start Procedure is you to obtain maximum benefit from the corrosion resis- required to start the vehicle.
Page 559: Preserving The Bodywork
SERVICING AND MAINTENANCE 557 To minimize the possibility of scratching the lenses and CAUTION! reducing light output, avoid wiping with a dry cloth. To • Do not use abrasive or strong cleaning materials such remove road dirt, wash with a mild soap solution followed by rinsing.
Page 560: Interiors
558 SERVICING AND MAINTENANCE • If you carry special cargo such as chemicals, fertilizers, Seat Belt Maintenance de-icer salt, etc., be sure that such materials are well Do not bleach, dye or clean the belts with chemical solvents packaged and sealed. or abrasive cleaners.
Page 561: Plastic And Coated Parts
SERVICING AND MAINTENANCE 559 Plastic And Coated Parts Leather Parts Use Mopar Total Clean to clean vinyl upholstery. Mopar Total Clean is specifically recommended for leather upholstery. CAUTION! Your leather upholstery can be best preserved by regular • Direct contact of air fresheners, insect repellents, cleaning with a damp soft cloth.
Page 562: Glass Surfaces
560 SERVICING AND MAINTENANCE CAUTION! Do not use Alcohol and Alcohol-based and/or Ketone based cleaning products to clean leather seats, as damage to the seat may result. Glass Surfaces All glass surfaces should be cleaned on a regular basis with Mopar Glass Cleaner, or any commercial household-type glass cleaner.
Page 563 TECHNICAL SPECIFICATIONS CONTENTS IDENTIFICATION DATA....562 FLEXIBLE FUEL — IF EQUIPPED ... .567 ▫...
Page 564: Identification Data
562 TECHNICAL SPECIFICATIONS IDENTIFICATION DATA BRAKE SYSTEM Your vehicle is equipped with dual hydraulic brake sys- Vehicle Identification Number tems. If either of the two hydraulic systems loses normal The Vehicle Identification Number (VIN) is on the left front capability, the remaining system will still function. How- corner of the instrument panel and is visible from outside ever, there will be some loss of overall braking effective- of the vehicle through the windshield.
Page 565: Torque Specifications
TECHNICAL SPECIFICATIONS 563 Torque Specifications Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice. Lug Nut/Bolt Torque **Lug Nut/ Lug Nut/ Bolt Size Bolt Socket Size 100 Ft-Lbs (135 N·m) M12 x 1.5 19 mm **Use only your authorized dealer recommended lug nuts/ bolts and clean or remove any dirt or oil before tightening.
Page 566: Fuel Requirements
564 TECHNICAL SPECIFICATIONS FUEL REQUIREMENTS Reformulated Gasoline Many areas of the country require the use of cleaner burning These engines are designed to meet all gasoline referred to as “Reformulated Gasoline”. Reformu- emissions regulations and provide opti- lated gasoline contains oxygenates and are specifically mum fuel economy and performance blended to reduce vehicle emissions and improve air quality.
Page 567: Gasoline/Oxygenate Blends
TECHNICAL SPECIFICATIONS 565 Indiscriminate use of fuel system cleaning agents should be CNG And LP Fuel System Modifications avoided. Many of these materials intended for gum and Modifications that allow the engine to run on compressed varnish removal may contain active solvents or similar natural gas (CNG) or liquid propane (LP) may result in ingredients.
Page 568: Fuel System Cautions
566 TECHNICAL SPECIFICATIONS Fuel System Cautions NOTE: Intentional tampering with the emissions control system can result in civil penalties being assessed against CAUTION! you. Carbon Monoxide Warnings Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gasoline is prohibited by Federal WARNING! law.
Page 569: Flexible Fuel - If Equipped
TECHNICAL SPECIFICATIONS 567 FLEXIBLE FUEL — IF EQUIPPED WARNING! (Continued) E-85 General Information materials lit or products that can cause spark in or near the vehicle when removing the fuel filler tube cap (gas The information in this section is unique for Flexible Fuel cap) or filling the tank.
Page 570: Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles
568 TECHNICAL SPECIFICATIONS NOTE: Starting • Use seasonally adjusted E-85 fuel (ASTM D5798). With The characteristics of E-85 fuel make it unsuitable for use non-seasonally adjusted E-85 fuel, hard starting and when ambient temperatures fall below 0°F (-18°C). In the rough idle following start up may be experienced even if range of 0°F (-18°C) to 32°F (0°C), an increase in the time it the above recommendations are followed, especially...
Page 571: Maintenance
TECHNICAL SPECIFICATIONS 569 Maintenance CAUTION! CAUTION! Replacing fuel system components with non-ethanol compatible components can damage your vehicle. Do not use ethanol mixture greater than 85% in your vehicle. It will cause difficulty in cold starting and may affect drivability. FLUID CAPACITIES U.S.
Page 572: Fluids And Lubricants
570 TECHNICAL SPECIFICATIONS FLUIDS AND LUBRICANTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend you use Mopar Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Tech- nology) or equivalent meeting the requirements of FCA Material Standard MS.90032. Engine Oil –...
Page 573 TECHNICAL SPECIFICATIONS 571 CAUTION! • Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) en- gine coolant (antifreeze), may result in engine dam- age and may decrease corrosion protection. Organic Additive Technology (OAT) engine coolant is differ- ent and should not be mixed with Hybrid Organic Additive Technology (HOAT) engine coolant (anti- freeze) or any “globally compatible”...
Page 574: Chassis
572 TECHNICAL SPECIFICATIONS Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission Use only Mopar ZF 8&9 Speed ATF Automatic Transmis- sion Fluid, or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. Brake Master Cylinder We recommend you use Mopar DOT 3 Brake Fluid, SAE J1703 should be used.
Page 575 MULTIMEDIA CONTENTS ▫ Accessing The System From The Uconnect UCONNECT RADIOS ....576 Radio .......628 PERSONALIZED MENU BAR .
Page 576 574 MULTIMEDIA ▫ Play Video Games ..... .643 ▫ Get Started ......660 ▫...
Page 577: Multimedia
MULTIMEDIA ▫ Additional Information ....673 CD/DVD DISC MAINTENANCE ... .674...
Page 578: Uconnect Radios
576 MULTIMEDIA UCONNECT RADIOS The new shortcut will now be an active App/shortcut on the main menu bar. For detailed information about your Uconnect radio, refer to your Uconnect Owner’s Manual Supplement. CYBERSECURITY PERSONALIZED MENU BAR Your vehicle may be a connected vehicle and may be equipped with both wired and wireless networks.
Page 579 MULTIMEDIA NOTE: WARNING! • FCA US LLC or your dealer may contact you directly • It is not possible to know or to predict all of the regarding software updates. possible outcomes if your vehicle’s systems are • To help further improve vehicle security and minimize breached.
Page 580: Uconnect Settings
578 MULTIMEDIA UCONNECT SETTINGS Customer Programmable Features — Uconnect 5.0 Settings The Uconnect system uses a combination of buttons on the touchscreen and/or buttons on the faceplate located on the center of the instrument panel that allow you to access and change the customer programmable features.
Page 581 MULTIMEDIA NOTE: Only one touchscreen area may be selected at a NOTE: All settings should be changed with the ignition in time. the “ON/RUN” position. When making a selection, press the button on the touch- KeySense screen to enter the desired mode. Once in the desired The vehicle’s KeySense settings are protected by a unique mode, press and release the preferred setting and make 4-digit PIN, which the vehicle owner creates when access-...
Page 582 580 MULTIMEDIA Setting Name Selectable Options ParkSense — If Equipped Sound Only Sound and Display Front ParkSense Volume Medium High Medium High Rear ParkSense Volume Rear ParkSense Braking Assist Blind Spot Alert — If Lights Lights & Chime Equipped NOTE: When the “Blind Spot Alert”...
Page 583 MULTIMEDIA Setting Name Selectable Options SiriusXM Setup Channel Skip Subscription Information NOTE: SiriusXM can be programmed to skip channels. To make your selection, press the “Channel Skip” button on the touchscreen, select the channels you would like to skip. New vehicle purchasers or lessees will receive a free limited time subscription to SiriusXM Satellite Radio with your radio.
Page 584 582 MULTIMEDIA Setting Name Selectable Options Brightness NOTE: The “Brightness” setting can also be adjusted by selecting any point on the scale between the “+” and “-” buttons on the touchscreen. Language English Español Français NOTE: Selecting any option within the “Language” setting will change the language for all displayed nomenclature, includ- ing the trip functions and the navigation system (if equipped).
Page 585 MULTIMEDIA Clock & Date After pressing the “Clock & Date” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Set Time and Format 12 hour 24 hour NOTE: Within the “Set Time and Format” setting, press the corresponding arrow buttons on the touchscreen to adjust to the correct time.
Page 586 584 MULTIMEDIA Safety/Assistance After pressing the “Safety/Assistance” button on the touchscreen, the following settings will be available: Setting Name Selectable Options ParkView Backup Camera Delay — If Equipped NOTE: The “ParkView Backup Camera Delay” setting determines whether or not the screen will display the rear view image with dynamic grid lines for up to ten seconds after the vehicle is shifted out of REVERSE.
Page 587 MULTIMEDIA Setting Name Selectable Options Forward Collision Warn- ing On/Off — If Equipped NOTE: Changing the FCW status to “Off” prevents the system from warning you of a possible collision with the vehicle in front of you. Near Forward Collision Warning-Plus (FCW+) —...
Page 588 586 MULTIMEDIA Setting Name Selectable Options Forward Collision Sound Only Sound and Brake Warning-Plus (FCW+) Ac- tive Braking — If Equipped NOTE: The “Forward Collision Warning Plus (FCW+)” setting includes Advanced Brake Assist (ABA). The ABA applies ad- ditional brake pressure when the driver requests insufficient brake pressure to avoid a potential frontal collision. When the “Sound Only”...
Page 589 MULTIMEDIA Setting Name Selectable Options Rear ParkSense Volume Medium High Front ParkSense Volume Medium High Rear ParkSense Braking Assist — If Equipped NOTE: When the “Rear ParkSense Braking Assist” feature is selected, the park assist system will detect objects located be- hind the vehicle and utilize autonomous braking to stop the vehicle.
Page 590 588 MULTIMEDIA Setting Name Selectable Options Blind Spot Alert — If Lights Lights and Chime Equipped NOTE: When the “Blind Spot Alert” feature is selected, the Blind Spot Monitor (BSM) system is activated and will show a visual alert in the outside mirrors, or it will show a visual alert in the outside mirrors as well as play an audible alert when the turn signal is on.
Page 591 MULTIMEDIA Lights After pressing the “Lights” button on the touchscreen, the following settings will be available. Setting Name Selectable Options Headlight Off Delay 0 sec 30 sec 60 sec 90 sec NOTE: When the “Headlight Off Delay” feature is selected, it allows the adjustment of the amount of time the headlights remain on after the engine is shut off.
Page 592 590 MULTIMEDIA Setting Name Selectable Options Automatic High Beam Headlamps — If Equipped NOTE: When the “Automatic High Beam Headlamps” is selected, the high beam headlights will activate/deactivate auto- matically under certain conditions. Daytime Running Lights Flash Lights With Lock Doors &...
Page 593 MULTIMEDIA Setting Name Selectable Options Personal Settings Linked to Key Fob — If Equipped NOTE: The “Personal Seetings Linked to Key Fob” feature provides automatic recall of all settings stored to a memory loca- tion (driver’s seat, exterior mirrors, steering column position and radio station pre-sets) to enhance driver mobility when entering and exiting the vehicle.
Page 594: Door Handle
592 MULTIMEDIA Setting Name Selectable Options Auto Unlock On Exit NOTE: When the “Auto Unlock On Exit” feature is selected, all doors will unlock when the vehicle is stopped and the trans- mission is in the PARK or NEUTRAL position and the driver’s door is opened. Flash Lights With Lock Sound Horn With Lock 1st Press...
Page 595 MULTIMEDIA Auto Comfort Systems — If Equipped After pressing the “Auto-On Comfort & Remote Start” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Auto-On Driver Heated/ Remote Start All Starts Ventilated Seat & Steering Wheel With Vehicle Start —...
Page 596 594 MULTIMEDIA Engine Off Options After pressing the “Engine Off Options” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Engine Off Power 0 sec 45 sec 5 min 10 min Delay — If Equipped NOTE: When the “Engine Off Power Delay”...
Page 597 MULTIMEDIA Compass Settings — If Equipped NOTE: Before compass calibration is performed, the com- pass variance zone should be set for best results. After pressing the “Compass Settings” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Compass Variance NOTE:...
Page 598 596 MULTIMEDIA Setting Name Selectable Options Compass Calibra- tion NOTE: Press “Compass Calibration” on the touchscreen to enter calibration. To start calibration of the compass, press the “Yes” button on the touchscreen and complete one or more 360-degree turns (in an area free from large metal or me- tallic objects).
Page 599 MULTIMEDIA Audio After pressing the “Audio” button on the touchscreen, the following settings will be available: Setting Name Adjustable Options Equalizer Bass Treble NOTE: When in this display you may adjust the “Bass”, “Mid” and “Treble” settings. Adjust the settings with the “+” and “–”...
Page 600 598 MULTIMEDIA Setting Name Adjustable Options Loudness NOTE: This feature improves sound quality at lower volumes when enabled. AUX Volume Offset — If Equipped NOTE: This feature provides the ability to tune the audio level for portable devices connected through the AUX input. Phone/Bluetooth After pressing the “Phone/Bluetooth”...
Page 601 MULTIMEDIA SiriusXM Setup — If Equipped After pressing the “SiriusXM Setup” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Channel Skip List of Channels NOTE: SiriusXM can be programmed to designate a group of channels that are the most desirable to listen to or to exclude undesirable channels while scanning.
Page 602 600 MULTIMEDIA Restore Settings After pressing the “Restore Settings” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Restore Settings Cancel NOTE: When the “Restore Settings” feature is selected it will reset all settings to their default settings. Clear Personal Data After pressing the “Clear Personal Data”...
Page 603: Customer Programmable Features
MULTIMEDIA Customer Programmable Features — Uconnect 8.4 NOTE: Settings • Only one touchscreen area may be selected at a time. • Depending on the vehicles options, feature settings may vary. When making a selection, press the button on the touch- screen to enter the desired mode.
Page 604 602 MULTIMEDIA After pressing the “KeySense” button on the touchscreen, and entering the KeySense PIN, the following settings will be available: Setting Name Selectable Options Forward Collision Warn- Near Medium Forward Collision Sensi- Near Medium tivity Forward Collision Warn- ing Active Braking NOTE: When the “Forward Collision Warning Active Braking”...
Page 605 MULTIMEDIA Setting Name Selectable Options Blind Spot Alert — If Lights Lights & Chime Equipped NOTE: When the “Blind Spot Alert” feature is selected, it will alert, visibly and/or audibly, to indicate objects are in your blind spot. The “Blind Spot Alert” feature can be activated in “Lights” mode. When this mode is selected, the Blind Spot Monitor (BSM) system is activated and will only show a visual alert in the exterior mirrors.
Page 606 604 MULTIMEDIA Setting Name Selectable Options SiriusXM Setup Channel Skip Subscription Information NOTE: SiriusXM can be programmed to skip channels. To make your selection, press the “Channel Skip” button on the touchscreen, select the channels you would like to skip. New vehicle purchasers or lessees will receive a free limited time subscription to SiriusXM Satellite Radio with your radio.
Page 607 MULTIMEDIA Setting Name Selectable Options Display Brightness With Headlights ON NOTE: To make changes to the Display Brightness with Headlights ON setting, the headlights must be on and the interior dimmer switch must not be in the party or parade positions. Display Brightness With Headlights OFF NOTE:...
Page 608 606 MULTIMEDIA Setting Name Selectable Options Set Language NOTE: When the “Set Language” feature is selected, you may select one of multiple languages (English / Français / Espa- ñol) for all display nomenclature, including the trip functions and the navigation system (if equipped). Press the “Set Language”...
Page 609 MULTIMEDIA Units After pressing the “Units” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Units Custom NOTE: The “Custom” option allows you to set the “Speed” (MPH, or km/h), “Distance” (mi, or km), “Fuel Consumption” [MPG (US), MPG (UK), L/100 km, or km/L], “Pressure”...
Page 610 608 MULTIMEDIA Clock After pressing the “Clock” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Sync Time With GPS — If Equipped Set Time Hours NOTE: The “Set Time Hours” feature will allow you to adjust the hours. The “Sync time with GPS” button on the touch- screen must be unchecked.
Page 611 MULTIMEDIA Safety & Driving Assistance After pressing the “Safety & Driving Assistance” button on the touchscreen, the following settings will be available: Setting Name Selectable Options ParkView Backup Camera Delay — If Equipped NOTE: The “ParkView Backup Camera Delay” setting determines whether or not the screen will display the rear view image with dynamic grid lines for up to ten seconds after the vehicle is shifted out of REVERSE.
Page 612 610 MULTIMEDIA Setting Name Selectable Options Surround View Camera NOTE: The “Surround View Camera” feature displays a complete 360 degree view of the vehicle’s exterior environment while backing up. Surround View Camera Delay NOTE: The “Surround View Camera Delay” setting determines whether or not the screen will display the 360 degree view image with guidelines for up to ten seconds after the vehicle is shifted out of REVERSE.
Page 613 MULTIMEDIA Setting Name Selectable Options Sliding Door Alert NOTE: When the “Sliding Door Alert” feature is selected, a chime plays when the sliding door reverses or an obstacle is sensed. Forward Collision Warn- Only Warning Warning + Active Braking ing — If Equipped NOTE: Changing the FCW status to “Off”...
Page 614 612 MULTIMEDIA Setting Name Selectable Options ParkSense — If Equipped Sound Only Sound and Display NOTE: The “ParkSense” system setting will scan for objects behind the vehicle when the transmission gear selector is in RE- VERSE and the vehicle speed is less than 7 mph (11 km/h), when enabled. It will provide an alert (audible and/or visual) to indicate the proximity to other objects.
Page 615 MULTIMEDIA Setting Name Selectable Options LaneSense Strength — If Medium High Equipped Blind Spot Alert — If Lights Lights and Chime Equipped NOTE: When the “Blind Spot Alert” feature is selected, the Blind Spot Monitor (BSM) system is activated and will show a visual alert in the outside mirrors, or it will show a visual alert in the outside mirrors as well as play an audible alert when the turn signal is on.
Page 616 614 MULTIMEDIA Lights After pressing the “Lights” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Headlight Off Delay 0 sec 30 sec 60 sec 90 sec NOTE: When the “Headlight Off Delay” feature is selected, it allows the adjustment of the amount of time the headlights remain on after the vehicle is shut off.
Page 617 MULTIMEDIA Setting Name Selectable Options Auto Dim High Beams— If Equipped NOTE: When the “Auto Dim High Beams” feature is selected, the high beam headlights will activate/deactivate automati- cally under certain conditions. Daytime Running Lights Flash Lights With Lock Doors & Locks NOTE: The auto door lock feature default condition is enabled.
Page 618 616 MULTIMEDIA Setting Name Selectable Options Personal Settings Linked to Key Fob — If Equipped NOTE: The “Personal Seetings Linked to Key Fob” feature provides automatic recall of all settings stored to a memory loca- tion (driver’s seat, exterior mirrors, steering column position and radio station pre-sets) to enhance driver mobility when entering and exiting the vehicle.
Page 619 MULTIMEDIA Setting Name Selectable Options Auto Unlock On Exit NOTE: When the “Auto Unlock On Exit” feature is selected, all doors will unlock when the vehicle is stopped and the trans- mission is in the PARK or NEUTRAL position and the driver’s door is opened. Flash Lights With Lock Sound Horn With Lock 1st Press...
Page 620 618 MULTIMEDIA Auto Comfort Systems — If Equipped After pressing the “Auto-On Comfort” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Auto-On Driver Heated/ Remote Start All Starts Ventilated Seat & Steering Wheel With Vehicle Start —...
Page 621 MULTIMEDIA Engine Off Options After pressing the “Engine Off Options” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Engine Off Power 0 sec 45 sec 5 min 10 min Delay — If Equipped NOTE: When the “Engine Off Power Delay”...
Page 622 620 MULTIMEDIA Audio After pressing the “Audio” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Balance/Fade Speaker Icon NOTE: When in this display you may adjust the “Balance/Fade” of the audio by pressing and dragging the “Speaker Icon” toward any location in the box.
Page 623 MULTIMEDIA Phone/Bluetooth After pressing the “Phone/Bluetooth” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Paired Phones List Of Paired Phones NOTE: This feature shows which phones are paired to the Phone/Bluetooth system. For further information, refer to the Uconnect Owner’s Manual Supplement.
Page 624 622 MULTIMEDIA SiriusXM Setup — If Equipped After pressing the “SiriusXM Setup” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Channel Skip List of Channels NOTE: SiriusXM can be programmed to designate a group of channels that are the most desirable to listen to or to exclude undesirable channels while scanning.
Page 625 MULTIMEDIA Accessibility — If Equipped After pressing the “Accessibility” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Accessibility NOTE: The “Accessibility” feature announces a function prior to performing the action selected when using DVD/Blu-ray and USB Video functions, when it is activated.
Page 626 624 MULTIMEDIA Clear Personal Data After pressing the “Clear Personal Data” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Clear Personal Data Cancel NOTE: When the “Clear Personal Data” feature is selected it will remove all personal data including Bluetooth devices and presets.
Page 627: Steering Wheel Audio Controls
MULTIMEDIA STEERING WHEEL AUDIO CONTROLS Pushing the center button will make the radio switch between the various modes available (AM/FM/SXM/ The remote sound system controls are located on the rear AUX, etc.). surface of the steering wheel at the three and nine o’clock positions.
Page 628: Aux/Usb/Mp3 Control
626 MULTIMEDIA AUX/USB/MP3 CONTROL There are multiple USB “charge only” ports in this vehicle. • In the center console There are numerous USB ports located throughout the vehicle. This feature allows an external USB device to be • On the back of the front row seats in the Uconnect plugged into the USB port.
Page 629: Uconnect Theater - If Equipped
MULTIMEDIA UCONNECT THEATER — IF EQUIPPED Uconnect Theater Overview Your Uconnect Theater is designed to give your family years of enjoyment. There are multiple ways to interact with your Uconnect Theater system. • Play your favorite CDs, DVDs or Blu-ray Discs •...
Page 630: Getting Started
628 MULTIMEDIA Getting Started Accessing The System From The Uconnect Radio Uconnect Theater Screen Uconnect Theater Button You can access your Uconnect Theater system from the 1 — Uconnect Theater Touchscreen radio touchscreen following the steps below: 2 — Uconnect Radio 3 —...
Page 631: Uconnect Theater Controls
MULTIMEDIA Option 2 Uconnect Theater Controls 1. Press the “Apps” button on the touchscreen. 2. Press the Uconnect Theater button on the touchscreen. NOTE: The Uconnect Theater icon may be dragged and dropped down to the personalized menu bar to create an App/shortcut.
Page 632: Accessing The System From The Uconnect Theater Rear Screens
630 MULTIMEDIA Parents can control certain features of the system with the Press this button and use the “Listen In” feature to listen to “Uconnect Theater Controls” screens, right from the audio through cabin speakers. Uconnect touchscreen radio. Options are: Accessing The System From The Uconnect •...
Page 633: Pairing The Remote
MULTIMEDIA NOTE: Pairing The Remote • There will be a touchscreen notification message when pairing is successful. Refer to “Pairing The Remote” on the full procedure of how to pair the remotes. • Test to make sure the remote is successfully paired by dragging your finger across the gesture pad.
Page 634: Unpairing The Remote
632 MULTIMEDIA 4. Press the “Remote” button on the Uconnect Theater Unpairing The Remote touchscreen found in the settings menu. In events such as updating the Uconnect Theater software, or taking a remote to another vehicle, the remote will need 5.
Page 635: Media Sources
MULTIMEDIA Media Sources NOTE: Use the “View Screen” function to pull content from one screen to the other in a single press of a button. Doing this however will disable and gray out certain player controls on the screen viewing the other screen’s content.
Page 636 634 MULTIMEDIA 3. Home Button — Push to access “Sources”. 11. Power Button — Turns the screen and wireless head- phone transmitter for the selected Channel on or off. 4. Arrow Buttons — Push the arrow buttons to highlight an item or scroll through menus. 12.
Page 637: Uconnect Theater Home Screen And Controls
MULTIMEDIA Uconnect Theater Home Screen And Controls Source Card Selection You can choose sources such as HDMI, USB, Apps, or Blu-ray. You may also view content of the opposite screen Uconnect Theater Home Screen in one step by choosing the “View Screen” source card. 1 —...
Page 638: Play A Dvd/Blu-Ray Or Usb Media File From Uconnect System
636 MULTIMEDIA General Settings Play A DVD/Blu-ray Or USB Media File From Uconnect System To change source card order, select “Source Card Reorder”, then press and hold source card on the touchscreen, and 1. Insert a Blu-ray disc or DVD disc into the disc player drag and drop in desired order.
Page 639 MULTIMEDIA 4. For DVD/Blu-ray disc – press Movie Snapshot on radio touchscreen, then press “OK” on following screen. For USB Media Files - Press Music, Movie, or Folders, then select media title from list(s). Source Controls — Uconnect Radio DVD Blu-ray Disc Player 1 —...
Page 640 638 MULTIMEDIA 2. Mute Mute rear headphones for selected source for the current ignition cycle. Pressing mute again will unmute rear head- phones. 3. Lock Press to enable/disable Remote Control functions and Touchscreen Controls for the selected source. 4. View Select this button to view full screen video if vehicle is not moving.
Page 641: Blu-Ray Controls - Disc Specific Functions
MULTIMEDIA Blu-ray Controls – Disc Specific Functions The four colored buttons (red, green, blue, yellow) are designed for use with certain Blu-ray disc movie titles to access particular features or software on the disc. See the documentation provided with your Blu-ray disc movie to see if these buttons can be used.
Page 642: Uconnect Theater Apps
640 MULTIMEDIA Uconnect Theater Apps Sudoku App Home Screen Select the Apps source card to play pre-loaded games. Pressing the “Help” button teaches users how to play each Apps Home Screen game. Pick from games: • Back Seat Bingo • Checkers •...
Page 643 MULTIMEDIA • Math Flash Cards Are We There Yet? — Uconnect 8.4 NAV • Solitaire • Sudoku • Tic Tac Toe NOTE: To exit a game, push “Exit Button” then “Back Arrow,” or “Home Button” on the touchscreen. Are We There Yet? App 1 —...
Page 644: Using The Rear Video Usb Port
642 MULTIMEDIA When a navigation route has been set from the Uconnect Using The Rear Video USB Port radio, the second row passengers can use “Are We There Yet?” for an animated screen showing distance and time remaining on navigation routes, as well as the estimated time of arrival with pop-up notifications.
Page 645: Play Video Games
MULTIMEDIA Search Screen AUX/HDMI/USB On the rear screen you can browse the content of the USB 1 — AUX Jack (Headphone Output Only) device by going to the USB source. Use the search feature 2 — HDMI Port to find your music faster. 3 —...
Page 646: Headphones Operation
644 MULTIMEDIA Headphones Operation The headphones receive two separate channels of audio using an infrared transmitter from the video screens. If no audio is heard after increasing the volume control, verify that the screen is turned on, the channel is not muted, the headphones are on, and that the headphone channel selector button is on the desired channel.
Page 647 MULTIMEDIA Changing The Audio Mode For Headphones Replacing The Headphone Batteries Each set of headphones requires two AAA batteries for 1. Ensure the remote control and the headphones are on operation. the same channel. To replace the batteries: 2. Push the Home button on the remote control. 1.
Page 648: Disc Menu
646 MULTIMEDIA What Does This Warranty Cover? Except as specified Delphi Automotive reserves the right to replace any dis- below, this warranty covers any Product that in normal use continued Product with a comparable model. THIS WAR- is defective in workmanship or materials. RANTY IS THE SOLE WARRANTY FOR THIS PRODUCT, SETS FORTH YOUR EXCLUSIVE REMEDY REGARDING What Does This Warranty Not Cover? This warranty does...
Page 649: Display Settings
MULTIMEDIA used to select specific chapters in a movie, navigate special Listening To Audio With The Screen Closed features, or to play the movie from the menu. To listen to only audio portion of the channel with the screen closed: NOTE: Inserting a disc into the player will “auto play”...
Page 650: Rear Climate Controls
648 MULTIMEDIA Rear Climate Controls The rear climate controls can also be controlled using the Uconnect Theater system. Refer to “Climate Controls” in “Getting To Know Your Vehicle” for further information. Rear Climate Controls Icon Description ON Button Press and release this button to turn the Rear Climate Controls on. Climate Control OFF Button Press and release this button to turn the Climate Controls off.
Page 651 MULTIMEDIA Icon Description Rear Passenger Temperature Up and Down Buttons Provides the rear passengers with independent temperature control. Push the button on the touchscreen to increase the temperature, as it moves towards the red arrow button on the touchscreen for warmer temperature settings.
Page 652: Accessibility - If Equipped
650 MULTIMEDIA Icon Description Blower Control Blower Control is used to regulate the amount of air forced through the climate system. There are seven blower speeds available. Adjusting the blower will cause automatic mode to switch to manual operation. The speeds can be selected using the buttons on the touchscreen. Accessibility —...
Page 653: Bd And Dvd Region Codes
MULTIMEDIA 5. Press the Select Input menu or the Wireless Streaming/ Settings Mirroring Source Card to select your device Below is a list of the settings available for the Wireless Streaming/Mirroring feature of your Uconnect Theater NOTE: The Authentication Screen will appear on both system: touchscreens.
Page 654 652 MULTIMEDIA • The player recognizes a maximum of 2000 files and 255 Recorded Discs folders (includes the ROOT folder) per CD-R and The Blu-ray Disc player will play CD-R and CD-RW discs CD-RW disc. recorded in CD-Audio or Video-CD format, or as a CD- •...
Page 655 MULTIMEDIA • AAC (MPEG-4 AAC, Low Complexity Profile) support. files must always end with the extension “.wma” or “.WMA” and AAC files must always end with the • AAC HE v1 (AAC High Efficiency v1 aka. AAC/ extension and “.aac” or “.AAC” or “m4a”. To prevent MPEG4v2 AAC+) support.
Page 656: Product Agreement
654 MULTIMEDIA Product Agreement Please refer the contract details which are disclosed in following website, for example, concerning these above Open Source Software software. http://www.gnu.org/licenses/old-licenses/gpl- The software built into this product, are composed of 2.0-standalone.html, http://www.gnu.org/licenses/lgpl- multiple software components, and there are the copy- 2.1-standalone.html, http://www.freetype.org/FTL.TXT.
Page 657 MULTIMEDIA boot_loader sh-ipl +g kernel 2.6.16.29 FreeType 2 2.2.1 gcc sh4eb 3.4.5 glibc 2.3.5 1.00 libgcc_s-3.4.5 bash-3.0-31 busybox 1.00 MAKE DEV 1.1.0 module-init-tools 3.1.0 libtermcap 2.0.8 mtd-utils 20050619 initscripts 8.11.1-1 libstdc+ +3.4.5-10 libiconv 1.11 binutils-sh4eb coreutils 6.9 dosfstools 2.10-3 directfb 1.0.0-rc1 kxml 1.21 2.16.91.0.2 v2lin 0.1...
Page 658: General Information
656 MULTIMEDIA NON-COMMERCIAL USE OF A CONSUMER TO (i) EN- message will be displayed and playback or copying will be CODE VIDEO IN COMPLIANCE WITH THE AVC STAN- interrupted. More information about Cinavia technology is DARD ( AVC VIDEO ) AND/OR (ii) DECODE AVC provided at the Cinavia Online Consumer Information VIDEO THAT WAS ENCODED BY A CONSUMER EN- Center at http://www.cinavia.com.
Page 659: Fcc/Ic Regulatory Notices
MULTIMEDIA 2. This device must accept any interference that may be FCC Class B digital device notice received including interference that may cause unde- This equipment has been tested and found to comply with sired operation. the limits for a Class B digital device, pursuant to part 15 of FCC/IC Regulatory Notices the FCC Rules.
Page 660: Radio Operation And Mobile Phones
658 MULTIMEDIA CAN ICES-3 (B) / NMB-3 (B) The internal wireless radio operates within guidelines found in radio frequency safety standards and recommen- This Class B digital apparatus complies with Canadian dations, which reflect the consensus of the scientific com- ICES-003.
Page 661: Uconnect Voice Recognition Quick
MULTIMEDIA NOTE: UCONNECT VOICE RECOGNITION QUICK TIPS • This equipment has been tested and found to comply Introducing Uconnect with the limits for a Class B digital device, pursuant to Start using Uconnect Voice Recognition with these helpful Part 15 of the FCC Rules. These limits are designed to quick tips.
Page 662: Get Started
660 MULTIMEDIA Get Started All you need to control your Uconnect system with your voice are the buttons on your steering wheel. 1. Visit UconnectPhone.com to check mobile device and feature compatibility and to find phone pairing instruc- tions. 2. Reduce background noise. Wind and passenger conver- sations are examples of noise that may impact recogni- tion.
Page 663: Basic Voice Commands
MULTIMEDIA 5. You can interrupt the help message or system prompts Basic Voice Commands by pushing the VR or Phone button and saying a Voice The basic Voice Commands below can be given at any Command from current category. point while using your Uconnect system. Push the VR button .
Page 664: Radio
662 MULTIMEDIA Radio Use your voice to quickly get to the AM, FM or SiriusXM Satellite Radio stations you would like to hear. (Subscrip- tion or included SiriusXM Satellite Radio trial required.) Push the VR button . After the beep, say •...
Page 665: Media
MULTIMEDIA • Change source to USB • Play artist Beethoven; Play album Greatest Hits; Play song Moonlight Sonata; Play genre Classical TIP: Press the “Browse” button on the touchscreen to see all of the music on your Bluetooth or USB device. Your Voice Command must match exactly how the artist, album, song and genre information is displayed.
Page 666: Phone
664 MULTIMEDIA • Redial (call previous outgoing phone number) • Call back (call previous incoming phone number) TIP: When providing a Voice Command, push the Phone button and say “Call,” then pronounce the name exactly as it appears in your phone book. When a contact has multiple phone numbers, you can say “Call John Smith work.”...
Page 667: Voice Text Reply
MULTIMEDIA 2. Listen to the Uconnect prompts. After the beep, repeat one of the pre-defined messages and follow the system prompts. PRE-DEFINED VOICE TEXT REPLY RESPONSES Yes. Stuck in traffic. See you later. Start without I’ll be late. Okay. Where are you? I will be <num- ber>...
Page 668: Climate
666 MULTIMEDIA Apple iPhone iOS 6 or later supports reading incoming TIP: Voice Text Reply is not compatible with iPhone, but if text messages only. To enable this feature on your Apple your vehicle is equipped with Siri Eyes Free, you can use iPhone, follow these four simple steps: your voice to send a text message.
Page 669: Navigation
• For the 8.4 Uconnect System, say: “Enter state.” steering wheel if equipped. • For the 8.4 NAV Uconnect System, say: “Find address 800 Chrysler Drive Auburn Hills, Michigan.” 2. Then follow the system prompts. TIP: To start a POI search, push the VR button .
Page 670: Uconnect Access
668 MULTIMEDIA Uconnect Access Vehicle Finder Send ‘N Go WARNING! Stolen Vehicle Assistance ALWAYS obey traffic laws and pay attention to the Remote Vehicle Start** road. Some Uconnect Access services, including 9-1-1 and Assist, will NOT work without an operable Remote Horn and Lights 1X(voice/data) or 3G(data) network connection.
Page 671: Mobile App
MULTIMEDIA • Once on the “Remote” screen, you can begin using Mobile App Remote Door Lock/Unlock, Remote Vehicle Start, and You’re only a few steps away from using remote com- activate your horn and lights remotely, if equipped. mands and sending a destination from your phone to your •...
Page 672: Yelp
670 MULTIMEDIA You must be registered with Uconnect Access and have a TIP: compatible MAP – enabled smartphone to use your voice • Voice Texting is not compatible with iPhone, but if your to send a personalized text message. For details about vehicle is equipped with Siri Eyes Free, you can use your MAP, visit UconnectPhone.com.
Page 673: Siriusxm Travel Link
MULTIMEDIA TIP: Once you perform a search, you can reorganize the Push the VR button . After the beep, say one of the results by selecting either the Best Match, Rating or Dis- following commands: tance tab on the top of the touchscreen display. •...
Page 674: Siri Eyes Free - If Equipped
672 MULTIMEDIA Siri Eyes Free — If Equipped Siri lets you use your voice to send text messages, select media, place phone calls and much more. Siri uses your natural language to understand what you mean and will respond back to confirm your requests. The system is designed to keep your eyes on the road and your hands on the wheel by letting Siri help you perform useful tasks.
Page 675: General Information
MULTIMEDIA Do Not Disturb can automatically reply with a text mes- 2. This device must accept any interference that may be sage, a call or both, when declining an incoming call and received including interference that may cause unde- send it to voicemail. sired operation.
Page 676 674 MULTIMEDIA CD/DVD DISC MAINTENANCE To keep a CD/DVD in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge.
Page 677 CUSTOMER ASSISTANCE CONTENTS ▫ Customer Assistance For The Hearing Or Speech SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE ......676 Impaired (TDD/TTY) .
Page 678: Suggestions For Obtaining Service For Your Vehicle
676 CUSTOMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR IF YOU NEED ASSISTANCE YOUR VEHICLE The manufacturer and its authorized dealer are vitally interested in your satisfaction. We want you to be happy Prepare For The Appointment with our products and services. If you are having warranty work done, be sure to have the right papers with you.
Page 679: Fca Us Llc Customer Center
Outside Mexico City: 1-800-505-1300 • Vehicle delivery date and mileage Puerto Rico And U.S. Virgin Islands FCA US LLC Customer Center Customer Service Chrysler International Services LLC P.O. Box 21–8004 P.O. Box 191857 Auburn Hills, MI 48321–8004 San Juan 00919-1857 Phone: (800) 247-9753 Tel.: (787) 782-5757...
Page 680: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
678 CUSTOMER ASSISTANCE Customer Assistance For The Hearing Or Speech questions about the service contract, call the manufactur- Impaired (TDD/TTY) er’s Service Contract National Customer Hotline at 1-800- 521-9922 (Canadian residents, call (800) 465-2001 English / To assist customers who have hearing difficulties, the (800) 387-9983 French).
Page 681: Warranty Information
CUSTOMER ASSISTANCE 679 REPORTING SAFETY DEFECTS WARNING! In The 50 United States And Washington, D.C. Engine exhaust (internal combustion engines only), If you believe that your vehicle has a defect that could some of its constituents, and certain vehicle compo- cause a crash or cause injury or death, you should nents contain, or emit, chemicals known to the State of immediately inform the National Highway Traffic...
Page 682: In Canada
680 CUSTOMER ASSISTANCE In Canada Diagnostic Procedure Manuals If you believe that your vehicle has a safety defect, you Diagnostic Procedure Manuals are filled with diagrams, should contact the Customer Service Department imme- charts and detailed illustrations. These practical manuals diately.
Page 683 INDEX...
Page 684 682 INDEX About Your Brakes ......562 Air Conditioning, Operating Tips ....128 Adaptive Cruise Control (ACC) (Cruise Control) .
Page 685 INDEX 683 Fluid Change ......531 Master Cylinder ......529 Fluid Level Check .
Page 686 684 INDEX Check Engine Light (Malfunction Indicator Light)..223 Connector Checking Your Vehicle For Safety ....312 UCI ........626 Checks, Safety .
Page 687 INDEX 685 Defroster, Windshield......313 Traction Control System ....227 Delay (Intermittent) Wipers .
Page 688 686 INDEX Oil Filler Cap ......507 Flexible Fuel Vehicles Oil Filter .......512 Cruising Range .
Page 689 INDEX 687 Gasoline .......564 Headlights Light ....... . .210 Bulb Replacement .
Page 690 688 INDEX Instrument Panel Lens Cleaning ....559 Lap/Shoulder Belts ......256 Interior And Instrument Lights.
Page 691 INDEX 689 Intensity Control ......97 Locks Interior ....... .95 Steering Wheel .
Page 692 690 INDEX Rearview ......86, 439 Oil Filter, Selection......512 Vanity .
Page 693 INDEX 691 Rearward .......69 Remote Keyless Entry Pregnant Women And Seat Belts ....266 Arm The Alarm .
Page 694 692 INDEX Safety Tips .......312 Rear Seat ......256 Schedule, Maintenance.
Page 695 INDEX 693 Snow Chains (Tire Chains) ....552 Steering Wheel Mounted Sound System Controls ..625 Snow Tires .......548 Storage, Vehicle .
Page 696 694 INDEX Jacking ......461, 463, 531 Traction Control ......227 Life Of Tires .
Page 697 INDEX 695 Uconnect Settings ....31, 593, 618 Voice Recognition System (VR) ....659 Uconnect Access Vehicle Health Alert .
Page 698 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this The antenna cable should be as short as practical and vehicle’s electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use frequency signals. Mobile two-way radios and telephone only fully shielded coaxial cable.

Chrysler PACIFICA 2017 Owner's Manual

Introduction

Getting to Know Your Vehicle

Getting to Know Your Instrument Panel

Safety

Starting and Operating

Starting and Operating 341

410 Starting and Operating

In Case of Emergency

Servicing and Maintenance

Quick Links

Chapters

Related Manuals for Chrysler PACIFICA 2017

Summary of Contents for Chrysler PACIFICA 2017