Craftsman 315.268192 Repair Sheet page 5

The model number will be found on a label attached to the motor housing. Always mention the model number in all correspondence regarding your
BELT SANDER or when ordering repair parts.
KEY PART
NO. NUMBER DESCRIPTION
1 660327002 Screw (8-32 X 1/2 in. Pan Hd.) **STD510805 ......11
2 200273004 Gear Box Cover Assembly ....................................1
3 900729001 Seal ........................................................................1
4 300897001 Rear Roller Shaft Assembly ...................................1
5 660299005 Screw (M5 x 11 mm) ..............................................4
6 6620803 Screw (M4 x 22 mm Pan Hd.) ................................9
7 300764004 Main Housing Assembly ........................................1
8 690715002 Wear Strip ..............................................................1
9 660366001 Screw (M4 x 12.5 mm Flat Hd.) .............................2
10 6939601 Retaining Ring .......................................................1
11 632450004 Yoke w/Shaft (S45C) ..............................................1
12 630438002 Spring Plate ...........................................................1
13 620233001 Front Roller Shaft ...................................................1
14 300432006 Front Roller Assembly ............................................1
15 590547007 Rotor Sit Cover ......................................................1
16 590539001 Fan Box Cover .......................................................1
17 200042012 Housing Assembly .................................................1
18 6620805 Screw (M4 x16 mm Pan Hd.) .................................7
19 660013005 Shoulder Screw .....................................................1
20 590541001 Release Lever ........................................................1
21 512010001 Brush Holder Cap ..................................................2
22 301036001 Brush Assembly .....................................................2
23 690761001 Torsion Spring ........................................................1
24 300998003 Armature Assembly ................................................1
SECTION "A" REPRESENTS AN IMPORTANT PART OF THE DOUBLE INSULATED SYSTEM OF THIS TOOL. ANY REPAIR TO THIS TOOL REQUIRES
DIELECTRIC TESTING TO INSURE CUSTOMER SAFETY AND TO COMPLY WITH COMPANY REQUIREMENTS.
CRAFTSMAN BELT SANDER – MODEL NUMBERS 315.268192
PARTS LIST
QTY.
** AvAILABLE FROM DIv. 98 – SOURCE 980.0
FOR SECTION A
KEY PART
NO. NUMBER
25 640755004
26 300777003
27 660299006
28 6611303
29 550339001
30 660568001
31 660106004
32 660299004
33 640585001
34 730356007
35 610326001
36 280013041
37 590274004
38 400873003
39 760314005
40 6627201
41 5950101
42 511184001
43 660008003
44 690715003
45 660279003
46 301035001
47 740524001
5
DESCRIPTION
Glamor Plate ..........................................................1
Rear Roller Assembly ............................................1
Screw (M5 x 44 mm Pan Hd.) ................................2
Screw (M2.5 x 8 mm Pan Hd.) ...............................1
Rubber Plug ...........................................................1
T-8 Socket Set (M3.5 x 1.27) .................................2
Lock Nut (M10) ......................................................1
Screw (M5 x 18 mm) ..............................................1
Driven Pulley ..........................................................1
Power Cord ............................................................1
Drive Pulley ............................................................1
Circuit Board Assembly .........................................1
Bend Relief ............................................................1
Dial .........................................................................1
Switch ....................................................................1
Screw (M4 x 14 mm Pan Hd.) ................................2
Cord Clamp ...........................................................1
Dust Guide Plate ....................................................1
Screw (M3 x 14 mm) ..............................................2
Wear Strip Plate .....................................................1
Screw (M4 x 11 mm) ..............................................2
Brush Holder ..........................................................2
Field .......................................................................1
QTY.