Table of Contents
Advertisement
Connecting to an active subwoofer
1
Connect the active subwoofer to the SUBWOOFER OUT
audio out jack (C). The subwoofer reproduces just the low
bass sound effect (e.g. explosions, the rumble of spaceships,
etc.). Be sure to follow the instructions supplied with the
subwoofer.
AMPLIFIER
ACTIVE
SUBWOOFER
F
G
C
DIGITAL AUDIO OUT
PCM-MPEG2-Dolby Digital-DTS
COAXIAL
OPT OUT
SUBW.
Note:
– If the audio format of the digital output does not match the
capabilities of your receiver, the receiver will produce a strong,
distorted sound or no sound at all.
– Six Channel Digital Surround Sound via digital connection
can only be obtained if your receiver is equipped with a Digital
Multi-channel decoder.
– To see the selected audio format of the current DVD in the
Status Window, press SYSTEM MENU.
NTSC/PAL Settings
You can switch the NTSC/PAL setting of the DVD player to
match the video signal of your TV. This setting only affects
the television's on-screen display that shows the stop and
setup modes. You may select either NTSC or PAL. To
change the DVD player setting to PAL or NTSC, follow the
steps below.
1
Unplug the DVD player from the mains.
2
Press and hold 9 and T, on the front of the DVD player.
While holding 9 and T, plug in the mains.
3
After PAL or NTSC appears on the display of the DVD
player, release 9 and T at the same time. The PAL or
NTSC indicator that appears on the display indicates the
current setting.
4
To change the setting, press T within three seconds. The
new setting (PAL or NTSC) will appear on the display.
TV
A
X
Z
Y
TV OUT
R
L
(CVBS)
(Y/C)
S-VIDEO OUT
AUDIO OUT
VIDEO OUT
NTSC/PAL Conversion
This player is equipped with a NTSC/PAL conversion
feature to convert the video output of the disc to match
your TV system. The conversions supported are as below:
Disc
Type
Format
DVD
NTSC
PAL
VCD
NTSC
PAL
1
In the Preference Menu, select TV System.
2
Press 3 or 4 to select PAL, NTSC or AUTO.
Notes:
– AUTO can only be selected when using a TV that has both
the NTSC and PAL systems.
– This is applicable for CVBS output on cinch and SCART only
– Slight picture distortions may occur due to this conversion.
This is normal. Thus, the AUTO format is most suitable for the
best picture quality.
General Explanation
About this manual
This manual gives the basic instructions for operating the
DVD player. Some DVDs require specific operation or
allow only limited operation during playback which may not
respond to all operating commands. When this occurs, the
symbol Ä appears on the TV screen, indicating that the
operation is not permitted by the player or the disc.
Remote control operation
¶ Unless stated, all operations can be carried out with the
remote control. Always point the remote control directly at
the player, making sure there are no obstructions in the
path of the infrared beam.
Corresponding keys on the front panel of the player can
also be used.
Menu bar operation
¶ A number of operations can be carried out via the menu
bar on the screen. The menu bar can be accessed by
pressing the cursor keys on the remote control.
¶ Pressing SYSTEM MENU while the menu bar is displayed
will clear the menu bar from the screen.
¶ The selected item will be highlighted and the appropriate
cursor keys to operate will be displayed below the icon.
¶ The symbols < or > indicate more items are available at
the left/right of the menu bar. Press 1 or 2 to select these
items.
Output format
Selected mode
NTSC
PAL
AUTO
NTSC
PAL
NTSC
Not
PAL
PAL
Supported
NTSC
PAL
NTSC
NTSC
PAL
PAL
P
REPARATION
9
Advertisement
Table of Contents
