Related Manuals for PAR EverServ ES500
Summary of Contents for PAR EverServ ES500
- Page 1 EverServ ® ® ES500 Installation and Configuration Guide Revision History 06/13/2013 - Revision 2 - MSR Configuration Functionality Added 04/10/2013 - Revision 1 - Pixel32 INI line fixed 12/03/2012 - Revision 0 - Initial Release...
- Page 2 Disclaimer PAR has thoroughly reviewed this document and believes it to be reliable. However, this document is provided for informational purposes only and PAR makes no warranties, either expressed or implied, in this document. Information in this document is subject to change without notice.
-
Page 3: Table Of Contents
Table of Contents ES500 Installation and Configuration Guide Overview ........................... 4 System Files ........................... 5 PixelPoint OPOS Files ........................... 6 PAR OPOS Drivers ........................... 7 Modifying Pixel32.ini ........................... 8 Cash Drawer Registry Configuration ........................... 9 Magnetic Swipe (MSR) Configuration ........................... 10... -
Page 4: Overview
Cash Drawer, Customer Display and MSR peripherals. In most cases, terminals ordered and shipped through PAR will arrive ready to go, in which case this document can be used as a reference guide. This document also contains information that can be referenced in cases where the Operating system has been replaced or configuration changes have been made in error. -
Page 5: System Files
System Files Begin the setup operation by obtaining the necessary system files. Open the "EverServ500" ZIP file containing these files. Extract the four ZIP files within: CCO.zip VFD.zip Cash Drawer.zip PixelPoint OPOS.zip Perform the following steps. For each step, make sure to run the executable as *Administrator*. -
Page 6: Pixelpoint Opos Files
PixelPoint OPOS Files If the Windows path on your system differs from the one shown in these instructions, modify the paths in these instructions accordingly. Extract the files from PixelPoint OPOS.zip, and then perform the following steps: 1. Copy to the \PixelPOS\DLLS directory. DrawerOPOSes500.dll PoleShowOPOS.dll Create this folder if it does not already exist. -
Page 7: Par Opos Drivers
PAR OPOS Drivers OPOS drivers should already be installed on the terminal when it ships from PAR. Look for them in the Windows Start Menu under "OPOS Utility". Run the utilities to ensure the OPOS devices are operating. If the OPOS Utility drivers are not installed, look for the installation file in the Setup.exe... -
Page 8: Modifying Pixel32.Ini
Modifying Pixel32.ini Edit \PixelPOS\ and add a section for each terminal. For example, if you have six pixel32.ini stations, you would need to have six station sections in the INI file. Make sure that each station section for an EverServ 500 terminal has the following lines under its heading. -
Page 9: Cash Drawer Registry Configuration
Cash Drawer Registry Configuration In order for the cash drawer to be properly configured, a particular key in the Windows Registry must have a particular value. It is set as follows: 1. Open the Windows Registry Editor. 2. Navigate through the keys (folders) on the left to the following path: \HKEY_LOCAL_MACHINE\SOFTWARE|OLEforRetail\ServiceOPOS\CashDrawer\FTCD1 3. -
Page 10: Magnetic Swipe (Msr) Configuration
Magnetic Swipe (MSR) Configuration Run the MagSwipe Configuration Utility and configure it as follows: 1. Press [Select Reader Interface] on the left 2. Select the image of the USB cable. 3. Select [Continue]. 4. Press [Change Basic Reader Settings] on the left 5. - Page 11 When you are finished, the following message will appear. At this point, your MSR has been configured and you can exit out of the MSR Configuration Utility. Page 11 Copyright © ParTech, Inc. 2013. All Rights Reserved. 6/13/2013...