Related Manuals for Yamaha VXS3SB
Summary of Contents for Yamaha VXS3SB
- Page 1 SPEAKER SYSTEM VXS3SB VXS3SW SPEAKER ACCESSORY CMA3SB Owner’s Manual Bedienungsanleitung CMA3SW Mode d’emploi Manual de instrucciones Manual do Proprietário Manuale di istruzioni 取扱説明書...
-
Page 2: Precautions
Location Hearing loss • Do not operate the device if the sound is • Do not place the device in an unstable distorting. Prolonged use in this condition • When turning on the AC power in your audio position where it might accidentally fall over could cause overheating and result in fire. system, always turn on the power amplifier and cause injuries. LAST, to avoid hearing loss and speaker • Do not place the device in a location where it damage. When turning the power off, the PA-8 1/2 VXS3SB / VXS3SW / CMA3SB / CMA3SW Owner's Manual... -
Page 3: Notice
Information capacity, malfunction or fire may occur. Do not place vinyl, plastic or rubber objects on the device, since this might discolor the device. About this manual The illustrations as shown in this manual are for Yamaha cannot be held responsible for When cleaning the device, use a dry and soft instructional purposes only. damage caused by improper use or cloth. Do not use paint thinners, solvents, modifications to the device. cleaning fluids, or chemical-impregnated The company names and product names in wiping cloths. this manual are the trademarks or registered PA-8 2/2 trademarks of their respective companies. Be sure to observe the amplifier’s rated load impedance (see Owner’s Manual), particularly when connecting speakers in parallel. Connecting an impedance load outside the amplifier’s rated range can damage the amplifier. VXS3SB / VXS3SW / CMA3SB / CMA3SW Owner's Manual... -
Page 4: Table Of Contents
Pre-installation (cable preparation) .......10 * SR-Bass™ represents the evolution of passive-type diaphragm technology. It is Yamaha's unique bass reproduction technology that efficiently converts the Installing.in.a.ceiling.(using.the.CMA3S)......13 energy inside the speaker cabinet into low-frequency sound. Painting..................16 * The contents of this manual apply to the latest specifications as of the publishing Painting the grille ..............16 date. To obtain the latest manual, access the Yamaha website then download the Painting the speaker enclosure ........16 manual file. Painting the ceiling mount adaptor ......17 Specifications................151 Dimensions................152 VXS3SB / VXS3SW / CMA3SB / CMA3SW Owner's Manual... -
Page 5: Included Accessories
Introduction Included accessories Optional accessories VXS3S Ceiling mount adaptor CMA3S Ceiling mount adaptor ×1 Square ring ×1 Speaker ×1 Grille ×1 Safety wire ×1 Terminal cover ×1 Tapping screw (4×12) ×8 Safety wire ×1 Mounting bracket ×1 Spacer ×3 Tapping screw (4×8) ×2 Hole cover sheet ×4 Cutout template ×1 Machine screw (M4×16) ×2 Masking sheet ×2 Owner's Manual (this document) Tile rails ×2 Masking sheet ×1 VXS3SB / VXS3SW / CMA3SB / CMA3SW Owner's Manual... -
Page 6: Connections
Power amplifier INPUT ＋ － Satellite speakers (×2) NOTICE • When connecting speakers with high impedence, select settings according to the above selector switch inscriptions according to the number of satelite speaker connections (NONE/×2/×4) and output (W). Make sure that the input total of each speaker does not exceed the rated output of the power amplifier. • Do not set the tap selector switch to the "X" position. • When using a low impedance connection, set the tap selector switch to the "8Ω" position. If the setting is incorrect, it may cause malfunction of the speaker and amplifier. • Make sure the amplifier is switched off before operating the tap selector switch. VXS3SB / VXS3SW / CMA3SB / CMA3SW Owner's Manual... -
Page 7: Connecting Satellites
„ VXS3S+VXS1ML (×4) low impedance connection This is a basic system. INPUT Power amplifier INPUT ＋ － INPUT ＋ Power amplifier － INPUT ＋ ＋ － － ＋ － ＋ － NOTICE ＋ When connecting satellites, the combined impedance is 4Ω (when connecting － 4 satellites) or 3.5Ω (when connecting 2 satellites). ＋ Make sure than the power amplifier is compatible with these impedances. If the power － amplifier is not compatible, the power amplifier may malfunction. VXS3SB / VXS3SW / CMA3SB / CMA3SW Owner's Manual... - Page 8 Hi-z Hi-z Hi-z additional systems INPUT THRU INPUT THRU Power amplifier INPUT THRU INPUT THRU ＋ ＋ ＋ ＋ － － － － NOTICE • When connecting speakers with high impedance, be sure that the rated output of the power amplifier exceeds the input total of each speaker. For details, refer to the explanation of high-impedance connection at the following URL. Yamaha Pro Audio site, "Better Sound for Commercial Installation" http://www.yamahaproaudio.com/global/en/training_support/better_sound/ • When installing speakers, make sure the power amplifier is turned off. VXS3SB / VXS3SW / CMA3SB / CMA3SW Owner's Manual...
-
Page 9: Installing.on.a.wall.or.ceiling
Horizontal installation Vertical installation r mark r mark CAUTION When installing the speaker in a vertical orientation, if the r mark on the mounting bracket is pointing down, the speaker cannot be se- cured to the mounting bracket and it may fall. Do not install the speak- er so that the r mark points down. VXS3SB / VXS3SW / CMA3SB / CMA3SW Owner's Manual... -
Page 10: Pre-Installation (Cable Preparation)
• Attach safety wire high enough so that there is not too much slack in the wire. • If the included safety wire is not long enough, consider the weight of the speaker and the installation conditions, and pro- cure an appropriate safety wire. Recommended area for pulling out cables Unit:mm VXS3SB / VXS3SW / CMA3SB / CMA3SW Owner's Manual... - Page 11 Secure the speaker to the mounting bracket Attach the safety wire to the speaker. Attach the safety wire so that its clasp fits inside the groove on Remove the grille. the speaker. Attach the speaker so that the r mark on the mounting bracket is facing the r mark on the speaker. r mark Connecting the cables Use a Phillips screwdriver to loosen the screws on the barrier strip, insert the cables, and then tighten the screws. For information about connecting the cables, refer to "Connections" on page 6. Make sure the cables are secure and cannot be pulled out. VXS3SB / VXS3SW / CMA3SB / CMA3SW Owner's Manual...
- Page 12 Installing on a wall or ceiling Slide the speaker about 10mm in the direction shown to tempo- CAUTION rarily secure the speaker. Make sure you tighten the screws. About 10mm NOTICE When installing the speaker, make sure you do not touch the flaps or subject the speaker to strong shocks. If the flaps become indented, the sound may become distorted. Flaps Use the supplied two screws to secure the speaker. Setting the line voltage/impedance and power Select the line voltage/impedance (100V/70V/8Ω) and power tap for 100V/70V line distributed system. For details, refer to page Attach the grille Align the grille to the front of the cabinet and attach the grille. CAUTION If the grille is not attached properly, it may fall off after the speaker is installed. VXS3SB / VXS3SW / CMA3SB / CMA3SW Owner's Manual...
-
Page 13: Installing.in.a.ceiling.(Using.the.cma3S)
Use the included cutout template (350mm×210mm) to mark the outline of the hole on the ceiling. NOTE Make sure to use the included cutout template; if the hole size is not correct, you will not be able to install the speaker. Cut along the outline and cut the hole. When cutting the hole, be careful to prevent debris or dust from entering your eyes. Attach the square ring and rails to the inside surface of the ceiling. Insert the two tile rails through the cut hole and place them on the ceiling surface within your reach. Be sure that each tile rails are oriented as shown in the illustration. Insert the square-ring through the cut hole. VXS3SB / VXS3SW / CMA3SB / CMA3SW Owner's Manual... - Page 14 Installing in a ceiling (using the CMA3S) Attach the ceiling mount adaptor to the speaker. Run the cables through the terminal cover. Remove the grille. Insert the speaker into the ceiling mount adaptor, and secure the speaker using the supplied four screws. Use a Phillips screwdriver to loosen the screws on the barrier strip, insert the cables, and then tighten the screws. For information about connecting the cables, refer to "Connections" (page 6). Make sure the cables are secure and cannot be pulled out. Tighten the screws and attach the terminal cover. Attach the safety wire Refer to Step 2 on page 10. Use the safety wire included with the CMA3S. Connecting the cables Feed the cables through the hole in the ceiling. VXS3SB / VXS3SW / CMA3SB / CMA3SW Owner's Manual...
- Page 15 Setting the line voltage/impedance and power Flaps Refer to page 6. Attach the hole cover sheets Attach the included hole cover sheets to the screw holes. While lifting the speaker up slightly, use a Phillips screwdriver to turn the screws clockwise and tighten the attachments screws. The clamp opens when you begin turning the screw. As you continue to turn the screw, the clamp slides down and pulls the speaker into the ceiling. NOTE If the clamp is difficult to open, turn the screw counter-clockwise one-half revolu- tion; this will make it easier to open. Attach the grille Attachment screw Align the grille to the front of the cabinet and attach the grille. CAUTION Clamp If the grille is not attached properly, it may fall off after the speaker is installed. VXS3SB / VXS3SW / CMA3SB / CMA3SW Owner's Manual...
-
Page 16: Painting
If the holes become clogged with paint, sound quality may be affected. Painting the grille When the paint is completely dry, remove the masking sheet and Remove the grille from the speaker, taking care not to scratch it. attach the emblem to the grille. Make sure the emblem is attached in the correct position. Remove the emblem on the front of the grille. The emblem is attached by adhesive tape. Attach the grille to the speaker. Tuck the included masking sheet under the crosspiece on the back Painting the speaker enclosure of the grille and insert the masking sheet. Remove any dust or dirt with a lint-free cloth. Do not sand the enclosure. Use spray paint to paint the enclosure. Cover the baffle and connectors using masking materials to avoid paint contact. NOTE Make sure the areas shown below are covered. Allow the paint to dry completely. VXS3SB / VXS3SW / CMA3SB / CMA3SW Owner's Manual... -
Page 17: Painting The Ceiling Mount Adaptor
Painting Spray the paint onto the ceiling mount adaptor and the hole cover Painting the ceiling mount adaptor sheets. Wipe off any dirt from the ceiling mount adapter before painting it. Do not file it down. Align the included masking sheet with the posts of the ceiling mount adaptor and insert the masking sheet. When the paint is completely dry, remove the masking sheet. Use masking tape to cover the posts and the screw heads (8 loca- tions total). NOTE Use masking tape as necessary to mask other areas. VXS3SB / VXS3SW / CMA3SB / CMA3SW Owner's Manual... -
Page 18: Specifications
Frequency range (-10dB) 65Hz - 180Hz Model CMA3SB CMA3SW TERMINAL BLOCKS(4pin) Input: ABS (V-0) 3.0mm ABS (V-0) 3.0mm +/-, Loop-thru: +/- Enclosure Black White Connector TERMINAL BLOCKS(8pin) Satellite output: +/- (ST1~ST4) Dimensions W386 × D233 × H90mm Max. wire size AWG 12(3.5sq) (Adapter only) (15 1/4" × 9 1/4" × 3 1/2") 15W, 7.5W, 3.8W, 1.9W Transformer Net Weght 0.44 kg (0.97 lbs) Taps 100V 15W, 7.5W, 3.8W Cutout size 350mm × 210mm (13 3/4" × 8 1/4") Full-range power limiting to protecting Overload protection network and transducers VXS3SB / VXS3SW / CMA3SB / CMA3SW Owner's Manual... -
Page 19: Dimensions
Dimensions VXS3SB/VXS3SW CMA3SB/CMA3SW (OPTION) ■ ANCHOR BRACKET AND SQUARE RING ■ WALL BRACKET ■ SQUARE RING ■ TILE RAIL φ11 Unit: mm VXS3SB / VXS3SW / CMA3SB / CMA3SW Owner's Manual... - Page 20 Dieses Symbol gilt nur innerhalb der Europäischen Union. Wenn Sie solche Artikel ausrangieren möchten, kontaktieren Sie bitte Ihre örtlichen Behörden oder Ihren Händler und fragen Sie nach der sachgerechten Entsorgungsmethode. (weee_eu_de_02) VXS3SB / VXS3SW / CMA3SB / CMA3SW Owner's Manual...
- Page 21 Este símbolo solo es válido en la Unión Europea. Si desea desechar estos artículos, póngase en contacto con las autoridades locales o con el vendedor y pregúnteles el método correcto. (weee_eu_es_02) VXS3SB / VXS3SW / CMA3SB / CMA3SW Owner's Manual...
- Page 22 * EMP: Euroopa Majanduspiirkond Para una información detallada sobre este producto Yamaha y sobre el soporte de garantía en la zona EEE* y Suiza, visite la dirección web que se incluye más abajo (la version del archivo para imprimir esta disponible en nuestro sitio web) o póngase en Latviešu...
- Page 23 Delegación Benito Juárez, México, D.F., C.P. 03900, México PT. Yamaha Musik Indonesia (Distributor) Tel: +39-039-9065-1 Tel: +52-55-5804-0600 Yamaha Music Center Bldg. Jalan Jend. Gatot Subroto Kav. 4, Jakarta 12930, SPAIN/PORTUGAL BRAZIL Indonesia Yamaha Music Europe GmbH Ibérica, Sucursal en España Yamaha Musical do Brasil Ltda.
- Page 24 雅马哈乐器音响 （中国） 投资有限公司 Yamaha Pro Audio global website 上海市静安区新闸路1818号云和大厦2楼 http://www.yamahaproaudio.com/ 客户服务热线 ： 4000517700 Yamaha Downloads 公司网址 ： http://www.yamaha.com.cn http://download.yamaha.com/ 制造商 ： 雅马哈株式会社 Manual Development Group 制造商地址 ： 日本静冈县滨松市中区中泽町10-1 © 2017 Yamaha Corporation 进口商 ： 雅马哈乐器音响 （中国）投资有限公司 进口商地址 ： 上海市静安区新闸路1818号云和大厦2楼 Published 04/2017 改版 CRZC-B0 原产地...