Note For Parts List - Denon dcd-485 Service Manual

NOTE FOR PARTS LIST

Part indicated with the mark " " are not always in stock and possibly to take a long period of time for supplying, or in
some case supplying of part may be refused.
When ordering of part, clearly indicate "1" and "I" (i) to avoid mis-supplying.
Ordering part without stating its part number can not be supplied.
Part indicated with the mark "
Not including Carbon Film ±5%, 1/4W Type in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.)
WARNING:
Parts marked with this symbol
Use ONLY replacement parts recommended by the manufacturer.
Resistors
Ex.: RN 14K 2E 182
Type Shape Power Resist- Allowable Others
and per- ance
formance
RD : Carbon 2B : 1/8W F
RC : Composition 2E : 1/4W G
RS : Metal oxide film 2H : 1/2W J
RW : W inding 3A : 1W K
RN : Metal film 3D : 2W M
RK : Metal mixture 3F : 3W
3H : 5W
Resistance
⇒
1 8 2 1800 ohm = 1.8 kohm
Indicates number of zeros after effective number.
2-digit effective number.
• Units: ohm
⇒
1 R 2 1.2 ohm
1-digit effective number.
2-digit effective number, decimal point indicated by R.
• Units: ohm
22
" is not illustrated in the exploded view.
have critical characteristics.
G FR
error
: ±1%
P : Pulse-resistant type
: ±2%
NL : Low noise type
: ±5%
NB : Non-burning type
: ±10%
FR : Fuse-resistor
: ±20%
F : Lead wire forming
Capacitors
Ex.: CE 04W 1H 2R2
Type Shape Dielectric Capacity Allowable Others
and per- strength
formance
F : ±1%
CE : Aluminum foil 0J : 6.3V
electrolytic
G : ±2%
CA : Aluminum solid 1A : 10V
electrolytic
J : ±5%
CS : Tantalum electrolytic 1C : 16V
K : ±10%
CQ : Film 1E : 25V
M : ±20%
CK : Ceramic 1V : 35V
CC : Ceramic 1H : 50V Z : +80%
CP : Oil 2A : 100V
CM : Mica 2B : 125V P : +100%
CF : Metallized 2C : 160V
CH : Metallized 2D : 200V C : ±0.25pF
2E : 250V D : ±0.5pF
2H : 500V = : Others
2J : 630V
Capacity (electrolyte only)
⇒
2 2 2 2200µF
Indicates number of zeros after effective number.
2-digit effective number.
• Units: µF.
⇒
2 R 2 2.2µF
1-digit effective number.
2-digit effective number, decimal point indicated by R.
• Units: µF.
Capacity (except electrolyte)
⇒
2 2 2 2200pF=0.0022µF
(More than 2) Indicates number of zeros after effective number.
2-digit effective number.
• Units: µF.
⇒
2 2 1 220pF
(0 or 1) Indicates number of zeros after effective number.
2-digit effective number.
• Units: pF.
• When the dielectric strength is indicated in AC, "AC" is included after the dieelectric
strength value.
M BP
error
HS : High stability type
BP : Non-polar type
HR : Ripple-resistant type
DL : For change and discharge
HF : For assuring high
frequency
U : UL part
–20% C : CSA part
W : UL-CSA type
–0% F : Lead wire forming