Grundig 22 VLE 521 BG Service Manual page 47

CONVENIENCE FUNCTIONS
Updating software
(for digital channels only)
1
In the »SETTINGS« menu, select the line
»Check For Updates updates« with » « or
V
» « and press »OK« to confirm.
Λ
– A search for new software will be made
and – if available – it will be installed.
Note:
If a search for software updates should be
7
made automatically, select the line »Auto-
<
matic OAD« with » « or » « and use » «
V Λ
>
or » « to select the option »On«.
– The software will be updated automati-
cally as far as possible.
2 Press »EXIT« to end the setting.
Restoring the television to the
default settings
This function allows you to delete the channel
lists and all custom settings.
1 In the »SETTINGS« menu, select the line
»Restore Factory Defaults« with » « or » «
V Λ
and press »OK« to confirm.
2 Press » « (green) to confirm the warning
message.
– The »Source Setup« menu appears.
3
Continue the settings with the chapter "Initial
set-up and tuning television channels" on
page 14.
46
ENGLISH
------------------------------------------------------------------------
Displaying signal information
(for digital channels only)
1 Open the menu with »MENU«.
2
Select the menu item »SOURCE SETUP« with
» « or » « and press »OK« to confirm.
V Λ
3
Select the line »Signal Information« with
» « or » « and press »OK« to confirm.
V Λ
– Information on the channel, network,
modulation, symbol rate, quality and
signal strength is displayed.
Notes:
The signal information changes in ac cord-
7
ance with the current input source.
The signal properties are displayed in the
7
lower section of the menu. The further the
bars for »Quality« and »Signal Strenght«
extend to the right, the better the reception
signal.
The signal level not only depends on your
7
receiver system, but also on the channel
which is currently active. Remember this
when aligning your antenna based upon
the signal level display.
4
Press »EXIT« to close the menu.
OPERATION USING EXTERNAL DEVICES
DIGI LINK
Your television is equipped with
the DIGI LINK function.
This function uses the CEC
(Consumer Electronics Control)
protocol.
CEC allows external devices which are connect-
ed to the »HDMI« sockets by an HDMI cable
(e.g. DVD player) to be operated with a remote
control.
Prerequisite is that the devices connected support
CEC. Read the operating manual for the external
device to find out how to activate the correspond-
ing function.
The DIGI LINK functions on your
television
Switching on the television
automatically from standby
If the external device (e.g. Blu-ray player) is
switched on, the television also switches on and
the appropriate HDMI preset is selected auto-
matically.
Depending on the features of the external de-
vice, the external device (e.g. AV receiver) can
be switched on alone, the television stays in
standby.
Automatic selection of the HDMI
preset on the television
If your television is switched on and you then
switch on the external device (e.g. DVD player),
the appropriate HDMI preset on the television
will be selected.
Selecting the menu language
The television menu language is automatically
selected on the external device (e.g. DVD player).
The external device must support this function.
Switching off the external device
automatically
If you switch your television to standby, the ex-
ternal device (if it is switched on) will also be
switched to standby.
DIGI LINK is always active on your television set.
-----------------------------
Searching for and activating
external devices
You can connect up to 11 devices with DIGI LINK
functions to your television.
1 Open the Tools menu with »TOOLS«.
2 Select the menu item »CEC« with » « or
V
» « and press »OK« to confirm.
Λ
– The »HDMI CEC Device List« appears.
3
Start the device search with » « (red).
– The devices found are displayed in the
menu.
4 Select the device for operation with » «,
V
< >
» «, » « or » « and press »OK« to mark it.
Λ
– If the selected device is connected to a
different input to the current one, a switch
to the respective input will occur auto-
matically.
5 Press »EXIT« to end the setting.
47
ENGLISH