Dtv Setup; Channel Edit; Digital Audio - Philips 27HT4000D User Manual

TV SETUP MENU & SUB-MENUS (CONTINUED)
USE CHANNEL TABLE ( ( NO / YES)
·
If USE CHANNEL TABLE is set to NO. The digital tuner will ignore the Virtual Channel Table (VCT) information that is contained
in the Program and System Information Protocol (PSIP) during channel installation or Direct Channel Command which is sent by
the TV set.
When VCT is ignored, the digital tuner will tune to the physical channel, Radio Frequency (RF) Channel. Program Map Table
(PMT), which is stored as channel number Major dot Minor (eg. 2.1) in the TV set. The virtual channels will not be used in this
case.
If USE CHANNEL TABLE is set to YES. Program and System Information Protocol (PSIP) is used during channel installation, and
Direct Channel Command.
The digital tuner will use the virtual channel information that is contained in the PSIP, to map the virtual channels to the physical
channels, which is also called Major dot Minor channel in this case.
For more information on the PSIP, you can refer to ATSC Standard, Program and System information Protocol for Terrestrial
Broadcast and Cable (Revision B), which can be found at the website http://www.atsc.org/standards/a_65b.pdf.
DIGITAL TV LABEL ( ( NO / YES)
·
If DIGITAL TV LABEL is set to NO. The Digital TV channel number will not be displayed on the screen.
If DIGITAL TV LABEL is set to YES. The Digital TV channel number will be displayed on the top right hand corner of the TV
screen for about 5 seconds whenever there is a change in digital TV channel.
For the changes in the Digital TV label to take effect, please conduct a cold / warm start when the setting is changed from Yes to
No, vice versa.

DTV SETUP

Entering the DTV SETUP menu allows you to edit features while you are in Digital TV mode.

CHANNEL EDIT

Channel edit allows you to add or skip channels from your favorite list.
1
Press CURSOR > or < to toggle between Added or Skipped. If Skipped is selected, the channels will
be skipped when scrolling channels with the CH+ or CH- . If
scrolling channels with the CH+ or CH- .
Note : When you are in Digital Mode you can only add or skip programs in Digital Channels.
Weak Dig Sig Weak Dig Sig
Digital broadcasting is still new. Therefore it is not uncommon for a broadcaster to only send out a digital signal for part
.
of a day The reception could also come and go. If you program your channels when the signal is not being sent or is
weak it will not be saved in your channel setup. Using the Weak Digital Signal feature here, you can add those channels
with weak or no signals to your channel list. Adding or skipping Weak Digital Signal can
Digital Mode.
AutoLock AutoLock (not supp AutoLock (not supp (not supp
Fact Ch Reset
Factory Channel Reset Factory Channel Reset feature lets you erase the contents of the master, user and favorite channel lists. This restores the TV to the Factory Channel Reset feature lets you erase the contents of the master, user and favorite channel lists. This restores the TV to the
initial state before the first Auto Program operation. For instructions on how to Auto Install the TV again, refer to page 12.

Digital Audio

Digital Aud
Digital Audio allows you to switch to another audio language when it is available.
Timer (not (not supported) supported)
Closed Caption Closed Caption
Closed Caption lets you select the default option or options that you have assigned to your Close captioning service. This
feature is ONLY available in Digital Mode. ONLY ONLY available in Digital Mode.
Emergency Alert ergency Alert
Emergency Alert lets you display or discard emergency alerts for Low or Medium priority. mergency Alert lets you display or discard emergency alerts for Low or Medium priority. mergency Alert
Note : Emergency Alert will not be visible if no broadcast is received or when the TV is in Standby mode.
/ YES)
/ YES)
orted) orted)
CH- CH- . If Added is selected, the channels will not be skipped when
Weak Digital Signal Weak Digital Signal feature here, you can add those channels
Weak Digital Signal Weak Digital Signal can
13
ONLY be done in ONLY ONLY be done in