Hitachi C 12RSH2 Handing Instructions
  1. Manuals
  2. Brands
  3. Hitachi Manuals
  4. Saw
  5. C 12RSH2
  6. Handing instructions
Hitachi C 12RSH2 Handing Instructions

Hitachi C 12RSH2 Handing Instructions

Hide thumbs Also See for C 12RSH2:
Table of Contents

Advertisement

Quick Links

See also: Instruction Manual
C 12RSH2
Handling instructions

Advertisement

Table of Contents
loading

Related Manuals for Hitachi C 12RSH2

Summary of Contents for Hitachi C 12RSH2

  • Page 1 C 12RSH2 Handling instructions...
  • Page 2 ™ Ó & 4 – ø9 mm 327 mm 282 mm (12-7/8") (11-1/8") ˛ ◊ ¸ Ç...
  • Page 3 Â ˜ ı Ï ˝ Ï ˝ ⁄ ¢ ∞ § º ˇ ™...
  • Page 4 ¯ ¯ ¯ & ˘ ¿ & ™ ª ª ¤ ¤ ‹...
  • Page 5 ⓐ ⓑ ⓐ ⓑ ⓐ ⓑ Î Î Î ¤ £ • Ô...
  • Page 6 & fi › · fl ° ¡ ‡ fl ∞ ⁄ ‚ ° ·...
  • Page 7 ‹ ⓐ ⓑ Ô  ¶ ⓑ Ò Á & Ü î Ø Å ∏ Í ¶...
  • Page 8 Ú „ „ ´ Œ ‹ ‰ 6 mm 17 mm 230V...
  • Page 9 Dust collection adapter 1 Handle z Mounting hole (4 places) Å (Optional accessory) 2 Lever (A) x 8 mm Depth Adjustment Bolt Í Hose band (Optional accessory) 3 Motor Head c Auxiliary Board Î Marking (pre-marked) 6 mm Knob Bolt 4 Gear Case Ï...

  • Page 10: General Operational Precautions

    9. Use only original HITACHI replacement parts. 13. Do not overreach. Keep proper footing and balance at all 10. This tool should only be disassembled for replacement times.
  • Page 11 Always wear eye protection. 22. Do not use saw blades manufactured from high speed steel. 23. Use only saw blades recommended by HITACHI. Always wear hearing protection. 24. The saw blades should be from 290 mm to 305 mm external diameter ranges.

  • Page 12: Specifications

    SPECIFICATIONS Max. Head Turntable Max. sawing dimension sawing Miter Max. Height 105 mm dimension Max. Width 312 mm Left 45° Max. Height 105 mm Max. Width 220 mm Right 45° Right 57° Max. Height 105 mm Max. Width 170 mm Bevel Left 45°...

  • Page 13: Prior To Cutting

    8. Base holder adjustment (Fig. 5) PRACTICAL APPLICATIONS Loosen the 6 mm bolt with the supplied 10 mm box wrench. Adjust the base holder until its bottom surface WARNING contacts the bench or the fl oor surface. ○ To avoid personal injury, never remove or place a After adjustment, fi...
  • Page 14 To adjust the lower limit position of the saw blade, follow (2) Then, turn the adjuster and shift the laser line. (If you turn the procedure (1) shown in Fig. 13. the adjuster clockwise, the laser line will shift to the right (1) Lower the motor head, and turn the 8 mm depth and if you turn it counterclockwise, the laser line will shift adjustment bolt and make adjustments so that there can...
  • Page 15 (2) After turning on the switch and checking that the saw Accordingly, press the handle down gently and carefully. blade is rotating at maximum speed, slowly push down ○ In slide cutting, gently push the handle back (rearwards) the handle while holding down the lever (A) and bring the in a single, smooth operation.
  • Page 16 CAUTION WARNING Always secure the workpiece with the right or left Always fi rmly clamp or vise to secure the crown molding hand and cut it by sliding the round portion of the saw to the fence; otherwise the crown molding might be backwards with the left hand.

  • Page 17: Maintenance And Inspection

    A damaged saw blade can cause personal injury and Repair, modifi cation and inspection of Hitachi Power a worn saw blade can cause ineff ective operation and Tools must be carried out by a Hitachi Authorized possible overload to the motor. Service Center.
  • Page 18 328326 324452 339652 328520 333732 322955 988101 998834 322283 230V: 999065 960017 960017 301806 321390 321390 301806 339730 339731 339625 321549 339661 339662 307956 949313 307956 949556 996722 322677 322047 965841 974561 339626 322047 949404 304043 324412 996722 996247 339624 339660 324464...
  • Page 20 Shinagawa Intercity Tower A, 15-1, Konan 2-chome, Minato-ku, Tokyo, Japan Code No. C99715112 F Printed in China...

Table of Contents