Table of Contents
Advertisement
EN 46
8.
LC4.1E AB
8.4.4
Installing a TV with the Wireless Smart-Loader
Use a Wireless Smart-Loader programmed with the settings
from a master TV of the same type.
•
Be sure to use the same method of programming the
Wireless Smart-Loader. It means that if you program the
Wireless Smart-Loader using the wireless method, you
have to use the same method to install the TV.
1. Wireless method (for LCD and CRT TVs):
–
Turn on the TV, press the "MENU" Key on the Wireless
Smart-Loader.
2. Wired method (for CRT TVs only):
–
Turn on the TV set, connect the Wireless Smart-
Loader to the TV set using the accessory cable.
Press the Volume "-" and "+" buttons on the TV set
simultaneously for 3 seconds.
Highlight "SMARTLOADER TO TV".
•
For wireless method:
press the right arrow key on the Wireless Smart-Loader.
•
For wired method:
press the TV Remote Control.
–
A number from 1-100 is displayed, indicating the data
transfer completed percentage, from the Wireless
Smart-Loader to the TV (100 = fully loaded).
SMARTLOADER TO TV ||| -------##
–
When data transfer is completed, ## = "100",
the following menu appears for 3 seconds:
TV READY >
–
After which the following message appears:
GOODBYE >
–
The TV set goes to stand-by now and will start up
automatically.
The TV set is now installed and ready for use.
8.4.5
Problems and Solutions:
•
The message "WRONG VERSION" appears on the
screen.
–
The Wireless Smart-Loader contains a master TV
installation set-up not compatible to the TV set to be
set-up. Reprogram the Wireless Smart-Loader from a
master TV set whose software version is compatible
with the software version of the TV set to be set-up.
•
The message "I2C ERROR" is displayed on the screen.
–
Bad connection of RJ11 cable or wrong data
transmission occurred, please try again.
•
TV does not respond to the Wireless Smart-Loader.
–
Check if the green LED lights up on the Wireless
Smart-Loader when any button is pressed, and check
if the batteries are in a good condition. When the red
LED lights up, the batteries must be replaced.
–
Try to bring the Wireless Smart-Loader closer to the
infra red receiver of the TV set and try again.
Tips:
•
Do not forget to write the software version and the type of
the relevant master TV set on the sticker, attached to the
backside of the Wireless Smart-Loader.
•
In case of empty- or missing batteries, it is still possible to
install TVs using the "wired method" of the Wireless Smart-
Loader (for CRT TVs only).
•
Without batteries, the Wireless Smart-Loader retains the
stored information for ten years.
Note:
•
Before the Wireless Smart-Loader is stored for a long
period of time, take out the batteries to prevent the contacts
from corrosion.
•
Wired Smart-Loading works with CRT TVs only. Wireless
Smart-Loading works with both, Flat TVs and CRT TVs.
Alignments
8.4.6
8.5
8.5.1
8.5.2
Required Software Versions
Be aware that the software used in these TV sets is NOT
similar to software used in the Mainstream LCD-TVs.
Used software versions in this chassis are:
•
LC4CHE1-1.xx (Hercules)
•
S4CHEX1-1.xx (for Scaler 15" XGA resolution)
•
S4CHEV1-1.xx (for Scaler 20" VGA resolution)
Ensure that this software is used in these sets (available on the
P4C service web site).
Hotel Mode Instructions
For Installation Menu access, Remote Control (RC1683803)
will be necessary.
The Benefits of the Hotel Mode
This TV set is especially designed to operate in Hotel Mode.
Hotel Mode offers the following benefits:
•
Access to the User Menu can be blocked.
This prevents users (e.g. guests) from changing or deleting
channel settings and/or modifying picture and sound
settings. Picture and sound settings can only be controlled
via pre-programmed Smart Settings and buttons on the
remote control. This ensures that TVs always start up
correctly.
•
A switch-on volume level and channel can be selected.
After switching on, the TV always starts-up on the specified
channel and volume level.
•
The maximum volume level can be limited in order to
prevent disturbance.
•
Channels can be blanked.
•
The keys VOLUME +/- , PROGRAM +/- and MENU, of the
TV set can be blocked.
•
Screen information can be suppressed.
Activating the Hotel Mode Setup menu
1. Switch "on" the TV set and select a TV channel.
2. On the remote control, enter the following key combination:
"319753", directly followed by the "MUTE" key.
3. The HOTEL MODE SETUP MENU appears on the screen.
4. Use the cursor keys to select and change the following
settings:
Table 8-1 Hotel Mode Setup Menu
Function
Possible selections
HOTEL MODE
ON /OFF
ON CHANNEL
0..99, EXTERNALS
CHANNEL BLANKED
ON/OFF
KEYBOARD LOCK
ON/OFF
MAX VOLUME
0..99
ON VOLUME
0..99
AUX VOLUME
0..99
OSD DISPLAY
ON/OFF
MONITOR OUT
OFF
ICONN MODE
OFF
5. Select "STORE" and press the "CURSOR RIGHT" key to
save the settings and exit the Hotel Mode setup.
To exit without saving, press the "MENU" key.
Hide quick links:
Advertisement
Table of Contents
