Adjusting The Clock; Before Operation - Sanyo Dc-MS5 Instruction Manual

ADJUSTING THE CLOCK
.
:.
Example: To set "PM 7:30",
1. Press the CLOCK button. The clock display appears.
After connecting the mains lead for the first time, when you press
the CLOCK button, the clock display blinks.
2. Press the AD.fUST button.
\l/
AM 12:00
The hours display blinks.
3. ~Press the >/ Fl or ~< /<< button to set the 'hours."
\l/
PM 7:00
\
\
4. Press the ADJUST button.
\l/
PM 7:00
The minutes display blinks.
5. Press the F/ M or
t44/44
button to set the "minutes."
\l/
PM 7:30
6. Press the ADJUST button. The clock stains.
PM 7:30
The time can be set accurately by pressing the ADJUST button
when a time signal is heard.
These operations can be done, even if the power is off.
To display the clock during operation, press the CLOCK button. Press
it again to return to the original display.
The clock operation and memory are backed up even with a power
failure lasting 30 seconds or less.
When a power failure lasts for more than 30 seconds, the memory
contents will be retained for several days, but the clock display will
- blink. Reset the time when the display blinks because of a power
failure.
\
BEFORE OPERATION
Turning the power on and off
Press the POWER button. The indicators and displays light and the
STANDBY indicator goes out. (Afferconnecting the mains lead, when you
press the POWER button for the first time, the volume reset feature
automatically sets the initial volume level "VOL 4".)
To turn off the power, press the POWER button again. The STANDBY
indicator lights. The clock display remains lit.
When the mains lead is connected to the AC outiet,
ihf?
STANDBY
indicator lights and the unit will respond to commands from the remo!e
control.
Smart start function
If the following buttons are pressed when the power is turned off, lhe
unit turns on automatically and the selected funcrion IS se!.
.
CD player section CD */11, DISC 1, DISC 2, DISC 3, +
OPEN/CLOSE
Tuner section TUNER/BAND
Casse!te section TAPE E ,4
Graphic display
Below indication appears on the display for a
fe.v
seconos t,r, en
corresponding operation button is pressed.
E,4, >>,4<, II, m,O,O, AL, l, 2,.....99
Selecting the function
Press the FUNCTION button to select the desired fi-:ction. Each time the
button is pressed, the display changes as follow's:
~ y)::{vDoA~(Ta&?~ -d
The function is automatically selected when CD p!ay or tape playback is
started, or when the TUNER/BAND button has been pressed (except
during recording).
When the function selection is changed, CD play or tape playback is
automatically stopped.
Adjusting the volume
Press the "+" or "-" VOLUME button,
The volume level appears by the digital reading (VOL O - VOL 10) and
spectrum bars in the LEVEL par7 on the display, then the digital display
disappears.
Bass expander system
Press the BASSXPANDER button to enhance the bass sound. "BASS"
appears on the display.
The initial setting of this function is ON.
Selecting the sound mode
Press the SOUND PRESET button to select the sound mode which
matches the frequency response of the music heard.
VIVID : For emphasizing the bass and treble ranges
MILD: For a little emphasizing the bass and treble ranges
VOCAL For de-emphasizing the treble range, and emphasizing the
bass range
NORMAL For listening to sound extending from the bass to treble
range with a flat response
Spectrum analyzer
Indicates the input level and peak value of each sound range.
To turn the changer mechanism lights off
1.
Press the FUNCTION button 10 select "CD".
2. While pressing the MEMORY button, press the OPEN/CLOSE button.
To turn the lights on, repeat steps above.
WHAT TO DO IF ...
If the operation of the unit or display is not normal or when all the memory
contents are to be cleared, disconnect the mains lead from the AC outlet,
then press the RESET button (rear of the unit) for 30 seconds or more.
5