Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for Bright Technology cb958b
-
Page 2: Table Of Contents
TABLE OF CONTENTS Preface----------------------------------------------------------------------------------------------------------------------------------------1 --------------------------------------------------------------------------------------------------------------------------------------1 NAMEPLATE -----------------------------------------------------------------------------------------------------------------------------------------1 WARNING ---------------------------------------------------------------------------------------------------------------------------------1 INTRODUCTION -----------------------------------------------------------------------------------------------------------------------------------2 INSTALLATION SAFETY REGULATION---------------------------------------------------------------------------------------------------------------------------------------2 2.CB958 BALANCE INSTALLATION & OPERATION MANUAL -----------------------------------------------------------------3 -------------------------------------------------------------------------------------------------------3 2.1PROTECTIVE COVER ASSEMBLY -------------------------------------------------------------------------------------------------------------4 2.2BALANCE SHAFT ASSEMBLY -----------------------------------------------------------------------------------------------------------4 2.3 EQUIPPING POWER SOURCE -----------------------------------------------------------------4 3 .CB958SERIES WHEEL BALANCER TECHNICAL PERFORMANCE ----------------------------------------------------------------------------------------------------4 3.1PERORMANCE &... - Page 3 --------------------------------------------------------------------------------------16 PRESS SENSOR INSTALLATION AND WIRING 7.4 GENERAL TROUBLESHOOTING & SOLUTION -------------------------------------------------------------------------------18 -----------------------------------------------------------------------------------------------------------19 STANDARD ACCESSORIES MAINTENANCE----------------------------------------------------------------------------------------------------------------------------20 9. OPERATION DETAILED DESCRIPTION-------------------------------------------------------------------------------------------23 HOW TO BALANCE A WHEEL------------------------------------------------------------------------------------------------------------23 APPENDIX 1 LAYOUT OFTHE POWER SUPPLY CARD--------------------------------------------------------------------------24 APPENDIX 2 WIRING DIAGRAM---------------------------------------------------------------------------------------------------------25...
-
Page 4: Preface
consult the documentation at any time. 1. PREFACE WARNING The manual is only to be considered valid for the During this period, the manufacturer will repair or machine serial number and model stated on the replace the parts returned or the machine itself, attached nameplate. -
Page 5: Safety Regulation
position. In particular, the machine must only be procedures and regulations. Operators are forbidden to installed and operated in protected environments use the machine under the influence of alcohol or drugs where there is no risk of exposure to water or liquids. that could affect his/her physical and mental capacity. - Page 6 - Any unauthorized changes or modifications made to ATTENTION： the machine automatically release the manufacturer from any liability in the case of damage or accidents WEAR PROTECTIVE GLOVE resulting from such changes or modifications. READ OPERATION MANUAL Meaning of the decals (including the one indicating caution) Lightning symbol This decal, positioned WEAR PROTECTIVE GLASSES...
-
Page 7: Balance Shaft Assembly
WARNING As shown of the above figure, slip the protective cover Any electrical connect in the workshop is only done by into the protective cover support tubeand insert the the qualified technical staffs and it should meet the socket head screw M10X50. -
Page 8: Transportation
－noise ≤69dB － Store environment: RH20%-95% －rim diameter 10″～30″ temperature-10℃-+60℃ －maximum wheel weight75kg －When transport and use the machine, do not pull the －rim width 1.5～20″ rotation shaft, or it will cause the permanent damage. －net weight 155 kg 4.1.1 After being sure that the package of your machine －max wheel diameter 47inch is perfect, you can carry the wheel balancer to the －working environment：temperature 0℃-50℃，RH：... -
Page 9: Safety Precautions
Position the wheel balancer in the desired position for use. It must be ensured the floor is leveled and of solid construction. The wheel balancer is designed for operation indoors and should not be exposed to moisture or direct sunlight. The wheel balancers described in this manual must be used exclusively to measure the extent and position of car wheel unbalances, within the limits... -
Page 10: Configuration & Use
B. CE mark indicates that this model of machine has CE certification. Learn the function and location of all the controls. C. SERIES NUMBER: The first 3 digital is the abbreviation of the model of the machine and the middle 4 is the production date and the last 4 is the product series number. -
Page 11: Display Panel
In the state of parameter input, it is input key for the distance from wheel to the wheel balancer. You can change the distance set value of the window by press the up/down key. The default unit is mm. When use the automatic scale, it is no need for you to use this key and the machine will automatically access the distance from the machine to the tire. -
Page 12: Basic Operation
are any foreign bodies in the tyre. Take off the original behind between the two spokes. weight. OPT: When you choose this function, you can realize the optimum of the rim, wheel and tire. The installation methods of the wheel：Positive MOT\CAR\BUS tire mode selection: positioning, negative positioning &... - Page 13 center hole When use the automatic scale, the distance from the and pay attention to its direction. Or it will cause the machine frame to the tire can be accessed inaccurate by the automatic scale. To reach the measurement measurement. accuracy, you must execute a self-calibration 6.3.2.3LARGE FLANGE DISK POSITION （OPTIONAL）...
- Page 14 key to realize the unit conversion from inch to mm. to help it start rotation, especially to the relative bigger ②The unit conversion of the D of the rim from inch to tyre, to prolong the working life of the motor. Normally, the display of D should be in inch.
- Page 15 weight ALU1 Dis1=Dis + ” DYNAMIC—clip the weight on both sides of rim（dynamic balance test once start） Br*=Br－1 ” Dia1=Dia2=Dia－1” STATIC— Stick weight in centre ALU2－to balance light aluminum alloy rim by hiding the weight inside. STATIC—optional balancing motorcycle When balancing motorcycle wheels, you require the (optional) motorcycle adaptor accessory MJ-II.
- Page 16 WEIGHT SPLIT FUNCTION ALU* Dis1=Dis When the customer select the self definition ALU Dis2= Dis from O point to the outside of the flange modes , first use the scale to measure the inside disk－ ‖ position of the self-definition weight and then hen press Dia1=Dia key to confirm.
-
Page 17: Supplementary Explanation
above. to confirm. 7.1.4 [SET]-[APP]-[ light tire minimum 6.7SUPPLEMENTARY EXPLAINATION: unbalance setup) You can setup 1Gr and 5Gr. The Once switching on, you will see standard dynamic setup is similar to the above. balance mode setup by the computer. When selecting 7.1.5 ALU mode and the configuration of the aluminum alloy 7.1.6 [SET]-[BIP]-[ ] (beeper setup) You can setup... - Page 18 Enter the scale calibration program ：[CAL]- [RL1]- You can execute the following step by step: [TES] [ DYN]( dynamic sensor test) [TES] [ Dis] (test for the distance to the machine ） [ ](distance to the machine) Press key to [TES] [Dia] (test for the rim diameter）...
-
Page 19: Error
The above operation step vector diagram is as follows： 7.2 ERROR INDICATION: Attention ： When change the computer board, the phase sensor or the press sensor, you must execute the self-calibration. When change the computer board, you should setup the parameter according to the parameter marked in the machine or on the original computer board. -
Page 20: General Troubleshooting & Solution
Sometimes, inaccurate balance or incorrect position is caused by the breakage of the press sensor. The changing method of the sensor is as following: (1)Remove the upper cover and the right side panel of the balancer. (2)Detach the nut1 and 2, elastic washer, plain washer and large flat washer. (3)Loose the back nut3.4.5 to detach every parts. -
Page 21: Standard Accessories
computer board fault Change the power board Change the computer board Balance sensor lead connect or contact no good 1.Connect again accurate & difficult memory value lost Correct the memory value to reach ―00‖ according to the manual. Each spin, There are foreign body on the rim or the Change the wheel change of the value... -
Page 22: Maintenance
Spring Plastic Protective Cover Plastic Gauge Extension OPTIONAL ACCESSORIES ACCESSORIES NAME ACCESSORIES NAME Guard Four Holes Adapter(40) Special Cone Flag (40) WEIGHT CENTERLESS POSITION CALIPER SCALE DK-W-1(40) DK-W-2(40) MJ-I(40) MJ-I I(40) The manufacturer will not bear any responsibility in the event of claims resulting from the use of 8. - Page 23 and not suitable to change or remove the grease. In addition, the speed of it is not too fast WARNING compared to the machine so no need to change Unplug the machine from the socket and make the grease. If you note the run of the bearing sure that all moving parts have been locked abnormal or there is noise, change the bearing.
- Page 24 away with distilled water on the collection procedures at the end of the life Corrosion on copper, ASTM D 4048 of your product. Resistance to water spray, ASTM D 4049, % spray When purchasing this product, your distributor will Wash away with water, ASMT D also inform you of the possibility to return another 1264, loss (weight%), @ 79°...
- Page 25 Water of the rim, marked on the tire. Press the key Foam NO Powder YES to realize the conversion of the Br unit . CO2 YES 4. Lower down the protective cover（you can also Warning This table contains general instructions to be press the start key）.
-
Page 26: Appendix 1 Layout Ofthe Power Supply Card
APPENDIX Ⅰ LAYOUT OF THE POWER SUPPLY CARD... -
Page 27: Appendix 2 Wiring Diagram
APPENDIX Ⅱ Wiring Diagram... - Page 28 Sequence No: Model: Production Date: WARRANTY Machine involves the warranty period of 90 days and the parts and components are 6 months. The manufacturer is only responsible for the normal wear, improper transportation or use and the maintenance without care. Manufacturer will not notify the customers when improve the products and production line for this warranty terms do not involve the change result.