Panasonic NV-FJ604 Series Operating Instructions Manual page 9

If you are connecting your VCR to a TV using Method 2,
follow the operations explained below.
To be able to watch the VCR picture on the TV, RF connection
requires the video playback channel to be set on the TV.
1 Switch the TV on.
2 Select an unoccupied programme position (which is
not tuned to a TV station).
If you are using a Panasonic TV, select programme
position "0".
3 Set the VCR/TV switch
4 Press the VCR-ON/OFF button
on.
5 Press the MENU button
for more than 5 seconds.
The number of the RF
output channel appears
on the VCR display.
The initial setting is
channel 36.
6 Tune your TV until the test pattern shown on the right
appears on the TV screen.
Now, the setting of the RF output channel is
complete.
≥ As the tuning method
differs depending on the
TV you are using, refer
to your TV's operating
instructions for details
about tuning.
7 Press the OK button .
The Country setting menu
appears on the TV screen.
8 Press the Cursor buttons
(3421) to select the
country where you are
using the VCR.
9 Press the OK button
and the VCR's Auto Setup
automatically starts and
tunes all available TV
stations and also sets the
clock. This takes about 5
minutes.
≥ If you select "Schweiz",
"Suisse" or "Svizzera" on
the Country setting menu,
see page 8.
10 When the indication
shown on the right
appears on the VCR
display, the Auto Setup is
complete.
To Cancel the Auto Setup Before It Has Finished
√
Press the EXIT button
to "VCR".
to switch the VCR
VCR display
Indication when the RF output
channel is 36 (example)
On Screen Display
VCR
Ch:36
Indication of the test pattern
Country
België Deutschland
Belgique Österreich
Belgien Portugal
Danmark Suomi
España Sverige
France Schweiz
Italia Suisse
Svizzera
Nederland
others
Norge
Menu for Country setting
Auto-Setup
Country : others
Tuning : Ch 21
Indication during Auto Setup
SP
CVC
Indication when Auto Setup
is complete
.
When the clock setting menu appears after Auto Setup
has finished:
See page 8.
To Confirm that the TV Stations Have Been
Tuned Correctly by the Auto Setup
Function
See page 8.
If the Picture on the TV's Video Playback
Channel Is Distorted
If, after setup, you select the video playback channel
on the TV and view a TV programme on a programme
position selected on the VCR, some interference may
occur in certain cases. If this happens, you can minimise
the distortion by changing the RF output channel on the
VCR to another number. Follow the operations below.
1 Set the VCR/TV switch
2 Press the MENU button
The number of the RF output channel appears on the
VCR display.
The initial setting is
channel 36.
3 Press the numeric buttons
VCR
output channel.
Enter a channel number which differs by 2 or 3 from
the one initially set number. For example, as the
original number is 36, enter 39.
VCR
4 Press the OK button
Note When You Have Changed the RF Output Channel:
After changing the RF output channel to a different number,
be sure to retune your TV to the VCR's new RF output
channel. (For details about tuning, refer to your TV's
operating instructions.)
1 Press the MENU button
2 When the test pattern
shown on the right appears
sharp and clear on the TV
screen, the tuning is
complete.
3 Press the EXIT button
to "VCR".
for more than 5 seconds.
Indication when the RF output
channel is 36 (example)
to change the RF
Indication after changing the RF
output channel to 39 (example)
to conclude the setting.
for more than 5 seconds.
VCR
Ch:39
Test pattern indication
to exit the On Screen Display.
9