Panasonic AK-HC3500ES Operating Instruction page 9

Controls and their functions
 Lens mount (Bayonet type)
This is where the lens is mounted.
 Lens clamp lever
The lens is inserted into the lens mount , and this lever
is then turned to clamp the lens in place.
 Lens cable, mic cable clamps
These are used to clamp the lens cable and mic cable in
place.
D Camera hangers (supplied)
When the buildup unit (AK-HBU500) is used, install
these hangers to the camera with supplied screws
(M  8 mm).
For details, refer to the Operating Instructions for
AK-HBU500.
E Tripod mount
Before securing the Multi-Format Camera to a tripod,
attach the tripod adapter (SHAN-TM700) which is
available as an optional accessory.
F Shoulder pad
This is used when the Multi-Format Camera is to be
carried on the shoulder.
It can be adjusted to position it more toward the front or
more toward the back.
G Slide lock release lever
This is held down while it is used to adjust the front/back
position of the shoulder pad F.
Use it to adjust the position of the shoulder pad so that
the camera can be operated more easily while it is being
carried on the shoulder.
H Shoulder strap fitting
This enables the shoulder belt to be attached.
I Optical cable clamp
This enables the optical cable to be clamped.
J Camera No. plate holder
This enables the accessory camera No. plate to be
attached.
K Optical fibre connector
(AK-HC3500E: OPS2402-R made by Tajimi)
(AK-HC3500ES: EDW.3K.93C.TLC made by LEMO)
This is used to connect with the CCU (camera control
unit) using the optical fibre cable. When it is not in use,
cover it with its protective cap.
 Camera power switch [POWER]
This is used to select the camera power input (power
supplied from the CCU or from an external connector)
and turn the power ON and OFF.
 Power LED
This lights up green when power is supplied to the
camera.
When the camera's power switch is set to OFF, this lights
up red if the CCU is connected, and it goes off if the CCU
is not connected (if the power was turned ON by the
CCU).
 Power circuit breaker [BREAKER]
This shuts off the power in the event of an overcurrent
while the DC 1 V power supply is used.
To reset the circuit breaker, eliminate what caused it to
trip, and then press the circuit breaker button.
 INCOM connectors 1, 2 [INCOM1, INCOM2]
The INCOM or headset plugs are connected here.
 INCOM1 MIC ON/OFF switch [MIC1 TALK]
This is the INCOM1 MIC ON/OFF selector switch.
 INCOM1 level control [INCOM1 LEVEL]
This is used to adjust the INCOM1 receiving volume level.
 INCOM2 MIC ON/OFF switch [MIC2 TALK]
This is the INCOM MIC ON/OFF selector switch.
 INCOM2 level control [INCOM2 LEVEL]
This is used to adjust the INCOM receiving volume level.
9 INCOM1 PGM1 level control [INCOM1 PGM1]
This is used to adjust the INCOM1 and PGM1 mixing
level.
 INCOM1 PGM2 level control [INCOM1 PGM2]
This is used to adjust the INCOM1 and PGM mixing
level.
 INCOM2 PGM1 level control [INCOM2 PGM1]
This is used to adjust the INCOM and PGM1 mixing
level.
 INCOM2 PGM2 level control [INCOM2 PGM2]
This is used to adjust the INCOM and PGM mixing
level.
9