Page 1 This Owner’s Manual explains the features of your new Toyota. Please read it and follow the instructions carefully so that you can enjoy many years of safe motoring.
Page 2 New vehicle warranty Accessories, spare parts and modification of your Toyota Your new vehicle is covered by the following Toyota limited warranties: A wide variety of non genuine spare parts and acces- S New vehicle warranty sories for Toyota vehicles are currently available in S Emission control systems warranty the market.
Page 3 The SRS airbag devices in your Toyota contains ex- plosive chemicals. If the vehicle is scrapped with the The spark ignition system of your Toyota meets all re- airbags left asthey are, it may cause an accident such quirements of the Canadian Interference−Causing as a fire.
Page 4 U−11 Quick index D If a service reminder indicator or warning buzzer comes on ..D If your vehicle will not start ........D If your engine stalls while driving .
Page 5 Part 1 OPERATION OF INSTRUMENTS AND CONTROLS— Chapter 1−1 Overview of instruments and controls S Instrument panel overview S Instrument cluster overview S Indicator symbols on the instrument panel...
Page 6 Instrument panel overview...
Page 8 Instrument cluster overview "Without tachometer...
Page 9 "With tachometer...
Page 10 Indicator Symbols on the Instrument Panel Open door warning light* Brake system warning light * SRS airbag warning light* Seat belt reminder light* Turn signal indicator lights Discharge warning light* Headlight high beam indicator light Low oil pressure warning light* Over−drive indicator light Cruise control indicator light* Malfunction indicator lamp*...
Page 11: Keys And Doors
S Back door subkey with the attendant. additional keys, duplicates can be made S Hood by a Toyota dealer using the key number. Since the doors and trunk lid can be S Theft deterrent system locked without a key, you should always...
Page 12 Side doors Side doors LOCKING WITH KEY LOCKING WITH INSIDE LOCK BUT- LOCKING WITH POWER DOOR LOCK SWITCH Turn the key towards the front of the vehicle to lock and towards the back to Push in the lock button to lock and pull To lock all the side doors simulta- unlock.
Page 13 Back door CAUTION Before driving, be sure that the doors are closed and locked, espe- cially when small children are in the vehicle. Along with the proper use of seat belts, locking the doors helps prevent the driver and passengers from being thrown out from the ve- hicle during an accident.
Page 14: Power Windows
Power windows The windows can be operated with the Automatic operation (to open only): switch on each door. Push the switch completely down and then release it. The window will fully open. The ignition key must be in the “ON” posi- To stop the window partway, lightly pull the tion.
Page 15: Trunk Lid
Trunk lid— OPERATING THE PASSENGERS’ WIN- CAUTION DOWS Use the switch on each passengers’ To avoid serious personal injury, you door or the switches on the driver’s must do the following. door that control each passengers’ S Always make sure the head, hands window.
Page 16 —Luggage security system —Lock release lever (with fold−down rear seat) CAUTION Keep the trunk lid closed while driv- ing. This not only keeps the luggage from being thrown out but also pre- vents exhaust gases from entering the vehicle. To open the trunk lid from the driver’s This system deactivates the lock re- seat, pull up on the lock release lever.
Page 17 —Luggage security system Hood (without fold−down rear seat) 2. After closing the trunk lid, insert This system deactivates the lock re- To open the hood, do the following. the master key and turn it counter- lease lever so that things locked in the 1.
Page 18: Theft Deterrent System
Theft deterrent system 3. Hold the hood open by inserting To deter the vehicle theft, the system is 2. In front of the vehicle, pull up on the the support rod into the slot. designed to give an alarm and keep the auxiliary catch lever and lift the engine from being started if any of the Before closing the hood, check to see that...
Page 19 Be careful not to use the key when open- Reactiviating the alarm ing either front door. This will cancel the Once set, the system automatically resets system. the alarm each time alll the side doors, 4. After making sure the indicator light trunk lid and hood are closed after the starts flashing, you may leave the ve- alarm stops.
Page 20 If the system does not work properly, have lid and hood.. 1. To open the fuel filler door, pull the it checked by your Toyota dealer. ON—The system will automatically be set lever up. when the time comes. The side doors,...
Page 21 S Make sure the cap is tightened se- curely to prevent fuel spillage in case of an accident. S Use only a genuine Toyota fuel tank cap for replacement. It has a built in check valve to reduce fuel tank vac- uum.
Page 22 To open the sun roof, push the switch S Never sit on top of the vehicle CAUTION on the “SLIDE” side. Pushing on the around the roof opening. opposite side will close it. To tilt up the To avoid serious personal injury, you rear end of the sun roof, push the must do the following.
Page 23 Front seats— Part 1 Seats —Seat adjustment precautions OPERATION OF While the vehicle is being driven, all ve- Adjust the driver’s seat so that the foot hicle occupants should have the seatback pedals, steering wheel and instrument INSTRUMENTS upright, sit well back in the seat and prop- panel controls are within easy reach of the erly wear the seat belts provided.
Page 24: Adjusting Front Seats
−Adjusting front seats ADJUSTING SEAT POSITION S Do not put objects under the seats as they may interfere with the seat- Pull the lock release lever up. Then lock mechanism or unexpectedly slide the seat to the desired position push up the seat position adjust- with slight body pressure and release ing lever;...
Page 25: Head Restraints
Fold−down rear seat Head restraints CAUTION When returning the seatback to the upright position: S Make sure the seat belts are not twisted or caught in the seatback and are arranged in their proper position for ready use. S Make sure the seatback is securely locked by pushing forward and rearward on the top of the seat- back.
Page 26 Seat belts− −Seat belt precautions Toyota recommends that the driver and Do not allow the child to stand up or kneel S Do not drive with the head re- passengers in the vehicle be properly re- on either rear or front seats. An unre- straints removed.
Page 27 S Inspect the belt system periodical- CAUTION ly. Check for cuts, fraying and loose parts. Damaged parts Persons should ride in their seats should be replaced. Do not disas- properly wearing in their seat belts semble or modify the system. whenever the vehicle is moving.
Page 28 The retractor will lock the belt during a your Toyota dealer. Do not use the sudden stop or on impact. It also may lock seat until the seat belt is fixed. It if you lean forward too quickly. A slow,...
Page 29 CAUTION CAUTION S High−positioned lap belts and Always make sure the shoulder belt loose−fitting belts both could is positioned across the center of cause severe injuries due to slid- your shoulder. The belt should be ing under the lap belt during a col- kept away from the neck, but not lision.
Page 30: Rear Center Seat Belt
S If the seat belt does not function normally, immediately contact your Toyota dealer. Do not use the seat until the seat belt is fixed. It cannot protect an adult occupant or your child from injury. To release the belt, press the buckle−...
Page 31 If your seat belt cannot be fastened se- curely because it is not long enough, a personalized seat belt extender is avail- able from your Toyota dealer free of charge. Please contact your local Toyota dealer so that the dealer can order the proper re- quired length for the extender.
Page 32 S Remember that the extender pro- CAUTION vided for you may not be safe when used on a different vehicle, or for S After inserting the tabs, make sure another person or at a different the tabs and buckle are locked and seating position than the one origi- that the belt is not twisted.
Page 33 SRS airbags (for driver and front passenger) The SRS airbag system is designed to The SRS (Supplemental Restraint Sys- This indicator comes on when the activate in response to a severe frontal tem) airbags are designed to provide ignition key is turned to the “ACC” or impact within the shaded area be- further protection to the driver and “ON”...
Page 34 However, this threshold velocity will be considerably higher if the vehicle strikes an object, such as a parked vehicle or sign pole, which can move or deform on impact, or if it is involved in an underride collision (e.g. a collision in which the noise of the vehicle “underrides”, or goes under, the bed of a truck.
Page 35 When the airbags inflate, they produce a CAUTION fairly loud noise and release some smoke along with the nitrogen gas. This is not S The SRS airbag system is de- harmful and does not indicate a fire. Be signed only as a supplement to sure to wash off any residue as soon as the primary protection of the driv- possible to prevent minor skin irritation.
Page 36 S Do not allow a child to stand up, or S A forward−facing child restraint S Do not sit on the edge of the seat to kneel on the front passenger system should be put on the front or lean over the dashboard when seat.
Page 37 Do not perform any of the following or open any components, such as changes without consulting your the steering wheel column cover, Toyota dealer. Such changes can front passenger airbag cover, interfere with proper operation of front passenger airbag, airbag sensor assembly.
Page 38 This SRS airbag system has a service re- In the following cases, contact your Toyo- The SRS (Supplemental Restraint Sys- minder indicator to inform the driver of op- ta dealer as soon as possible: tem) airbag is designed to provide fur- erating problems.
Page 39 However, this threshold velocity will be considerably higher if the vehicle strikes an object, such as a parked vehicle or sign pole, which can move or deform on im- pact, or if it is involved in an underride col- lision (e.g. a collision in which the noise of the vehicle “underrides”, or goes under, the bed of a truck.
Page 40 Deployment of the airbags happen in a fraction of a second, so the airbags must inflate with considerable force. While the system is designed to reduce serious inju- ries, it may also cause minor burns or abrasions and swellings. The steering wheel hub may be hot for several minutes, but the airbag itself will not be hot.
Page 41 Do not perform any of the following ries. changes without consulting your Toyota dealer. Such changes can interfere with proper operation of the SRS airbag system in some cases. zInstallation of electronic items such as a mobile two−way radio,...
Page 42 Child restraint— —Child restraint precautions Toyota strongly urges the use of child restraint systems for children small enough to use them. The laws of all fifty states in the U.S.A. and Canada now require the use of a child restraint system.
Page 43 Child restraint— —Child restraint precautions Toyota strongly urges the use of child restraint systems for children small enough to use them. The laws of all fifty states in the U.S.A. and Canada now require the use of a child restraint system.
Page 44: Child Restraint System
—Child restraint system A child restraint system for a small S Toyota strongly urges use of a child or baby must itself be properly proper child restraint system CAUTION which conforms to the size of the restrained on the seat with either the child and is put on the rear seat.
Page 45 If your child restraint system does not pro- vide any of the necessary parts, you can purchase the following items from your Toyota dealer. S CRS installation kit (Part No. 04731−22012) −contains 1 bolt, 3 types of spacers and 1 locking...
Page 46 —Built−in child restraint...
Page 47 The built−in child restraint system If your child’s shoulders are above the S Be careful not to damage the belt upper shoulder belt position, do not mainly consists of a child seat inte- webbing or hardware. Take care use the built−in child restraint. Your grated in the rear seat and 5−point seat that they do not get caught or child should use the vehicle’s seat...
Page 48 1. Separate the fastener tapes behind 2. While pulling the seat belt release 3. Compress the shoulder belt clip to the head restraint to separate the strap (black), pull both shoulder separate the right and left shoulder head pad from the seatback. Lower belts together.
Page 49 CAUTION If you have removed the child seat pad for cleaning etc., do not use the built−in child restraint without the pad. To move the shoulder belts from the lower 1. Add slack to the shoulder belts by slot to the upper slot: pulling both of them together while pulling the black seat belt release 1.
Page 50 S When the built−in child restraint is in use, do not use the adult lap and shoulder belt instead of the built− in child restraint seat belt as it can cause severe injury to the child in a sudden stop or crash. S After moving the shoulder belts, make sure the belts are properly routed and that they are not twisted...
Page 51 S If the seat belt does not function normally, it cannot protect your child from injury. Contact your Toy- ota dealer immediately. Do not use the built−in child restraint until the seat belt is fixed. 6. Fasten the shoulder belt clip. 7.
Page 52 —Types of child restraint system Child restraint systems are classified into the following 3 types depending on the child’s age and size. (A) Infant seat (B) Convertible seat (C)Booster seat Install the child restraint system following the instructions provided by its manufac- turer.
Page 53 —Installation with 2−point type seat belt (A)INFANT SEAT INSTALLATION An infant seat is used in rear−facing position only.
Page 54 CAUTION S After inserting the tab, make sure the tab and buckle are locked and that the lap belt is not twisted. S Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.
Page 55 2. While pressing the infant seat firmly 3. To remove the infant seat, press the CAUTION against the seat cushion and seat- buckle−release button. back, tighten the lap belt by pulling its Push and pull the child restraint free end to hold the infant seat secure- system in different directions to be sure it is secure.
Page 56 (B)CONVERTIBLE SEAT INSTALLA- 1. Run the center lap belt through or CAUTION around the convertible seat following the TION instructions provided by its manufacturer A convertible seat is used in forward Do not put a rear−facing child re- and insert the tab into the buckle taking facing and rear−facing position de- straint system in the rear seat if it in- care not to twist the lap belt.
Page 57 CAUTION S After inserting the tab, make sure the tab and buckle are locked and that the lap belt is not twisted. S Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.
Page 58 —Installation with 3−point type seat belt 3. To remove the convertible seat, press (A) INFANT SEAT INSTALLATION the buckle−release button. CAUTION An infant seat is used in rear−facing position only. S Vehicles with a passenger airbag: Never put a rear−facing child re- straint system in the front seat be- cause the force of the rapid infla- tion of the passenger airbag can...
Page 59 CAUTION S After inserting the tab, make sure the tab and buckle are locked and that the lap belt is not twisted. S Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.
Page 60 2. Fully extend the shoulder belt to put it 3. While pressing the infant seat firmly CAUTION in the lock mode. When the belt is then against the seat cushion and seat- retracted even slightly, it cannot be ex- back, let the shoulder belt retract as far Make sure the seat belt is securely tended.
Page 61 4. To remove the infant seat, press the (B)CONVERTIBLE SEAT INSTALLA- CAUTION buckle−release button and allow the TION belt to retract completely. The belt will A convertible seat is used in forward- S Vehicles with a passenger airbag: move freely again and be ready to facing and rear−facing position de- work for an adult or older child passen- Never put a rear−facing child re-...
Page 62 1. Run the lap and shoulder belt through S A forward−facing child restraining S Do not put a rear−facing child re- or around the convertible seat follow- system should be put on the front straint system in the rear seat if it ing the instructions provided by its seat only when it is unavoidable.
Page 63 CAUTION S After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted. S Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.
Page 64 4. To remove the convertible seat, press (C)BOOSTER SEAT INSTALLATION the buckle−release button and allow CAUTION A booster seat is used in forward−fac- the belt to retract completely. The belt ing position only. will move freely again and be ready to S Make sure the seat belt is securely work for an adult or older child passen- locked.
Page 65 CAUTION S Always make sure the shoulder belt is positioned across the cen- ter of child’s shoulder. The belt should be kept away from child’s neck, but not falling off child’s shoulder. Failure to do so could re- duce the amount of protection in an accident and cause serious in- juries in a collision.
Page 66 —Top strap anchors and locations S If the seat belt does not function normally, it cannot protect your child from injury. Contact your To- yota dealer immediately. Do not use the seat until the seat belt is fixed. 2. To remove the child restraint system, If your child restraint system requires press the buckle−release button and the use of a top strap, latch the hook...
Page 67 Using the illustration as a guide, run Toyota dealer. (See “—Child restraint sys- and release the lever. your fingers across trim of the filler pan- tem”.)
Page 68 Using the illustration as a guide, run Toyota dealer. (See “—Child restraint sys- and release the lever. your fingers across trim of the filler pan- tem”.)
Page 69 —Rear view mirror remote Outside rear view mirrors— control CAUTION Do not adjust the mirror while the vehicle is moving. It may cause the driver to mishandle the vehicle and an accident may occur resulting in personal injuries. Adjust the mirror so you can just see To adjust the rear view mirror, simply the side of your vehicle in the mirror.
Page 70 —Power rear view mirror Anti−glare inside rear view —Folding rear view mirrors control mirror To adjust a power rear view mirror, first To fold the rear view mirror, push back- Pull the lever toward you to reduce push the master switch in “L’ (left) or ward.
Page 71 Part 1 Headlights and turn signals OPERATION OF FIRST CLICKSTOP: Only the parking, tail, license plate, side marker and instru- INSTRUMENTS AND ment panel lights turn on. SECOND CLICKSTOP: The headlights CONTROLS— also turn on. If you remove the key with the headlights left on, a buzzer reminds you to turn the Chapter 1−4 lights off when you open the driver’s door.
Page 72: Emergency Flashers
Emergency flashers To turn on the emergency flashers, For high beam, push the lever away For signaling turns, move the lever up push the switch. from you. Pull it toward you for low or down in the conventional manner. All the turn signal lights will flash. To turn beam.
Page 73 Instrument panel light control Interior light NOTICE To prevent the battery from being discharged, do not leave the lights on for a long period when the engine is not running. To adjust the brightness of the instru- To turn on the interior light, slide the ment panel lights, turn the dial.
Page 74: Personal Light
Windshield wipers and washer (intermittent type without interval adjuster) Personal light NOTICE Do not operate the wipers if the windshield is dry. It may scratch the glass. To turn on the personal light, push the To turn the wipers on, move the lever. switch.
Page 75 Windshield wipers and washer (intermittent type Windshield wipers and with interval adjuster) washer (mist type) If the washer does not work, check to see whether the washer tank is empty. For in- formation on adding washer fluid, see “Adding washer fluid” in Chapter 7−3. In cold weather, warm the windshield with the defroster before using the washer.
Page 76 Rear window defogger NOTICE Do not operate the wipers if the windshield is dry. It may scratch the glass. Make sure you turn the defogger off when To defog or defrost the rear window, the window is clear. Leaving the defogger push the switch.
Page 77: Engine Coolant Temperature
If the indicator lamp does It is a good idea to keep the tank over 1/4 S Tachometer not go off, contact your Toyota dealer as full. soon as possible. S Odometer and trip meter This fuel gauge has a non−return type...
Page 78 Engine coolant temperature Tachometer gauge The gauge indicates the engine cool- S Idling for a long period with the air con- tachometer indicates engine ant temperature when the ignition speed in thousands of rpm (revolu- ditioning on in stop−and−go traffic. switch is on.
Page 79 Service reminder indicators Odometer and trip meter and warning buzzers The odometer records the total dis- tance the vehicle has been driven. The trip meter may be set to zero to record the distance on each trip. To reset the trip meter, press the trip meter reset knob.
Page 80 Turn off the air conditioning, vehicle towed in for repairs. (For tow- block. It may ruin the engine. blower, radio, ect., and drive directly to the ing information, see Part 4.) nearest Toyota dealer or repair shop.
Page 81 This light comes on when the fuel level in This light will come on when the igni- your Toyota dealer as soon as possible. the tank becomes nearly empty. Fill up tion key is turned to the “ACC” or “ON”...
Page 82 If any service reminder indicator or warn- ing buzzer does not function as described above, either the bulb is burned out or the circuit is in need of repair. Have it checked by your Toyota dealer as soon as pos- sible.
Page 83: Ignition Switch
Ignition switch with steering Part 1 lock OPERATION OF “LOCK” − Engine is off and the steer- ing wheel is locked. The key can be re- INSTRUMENTS AND moved only at this position. You must push in the key to turn the key CONTROLS—...
Page 84 Automatic transmission (3−speed type) Vehicles with cruise control − When the cruise control is being used, even if you downshift the transmission, engine braking will not be applied because the cruise control is not cancelled. For ways to decrease the vehicle speed, see “Cruise control” in this chapter.
Page 85 Your automatic transmission has a shift S Shift into the “2” position when the ve- With the selector lever in “2” or “L”, you lock system to minimize the possibility of can start the vehicle in motion as with the hicle speed is lower than the 90 km/h incorrect operation.
Page 86 (d) Backing up (f) Good driving practice NOTICE 1. Bring the vehicle to a complete stop. CAUTION If you rock your vehicle, observe the 2. With the brake pedal held down with following precautions to prevent your foot, shift the selector lever to the Always keep your foot on the brake damage to the transmission and “R”...
Page 87 Automatic transmission (4−speed type) Vehicles with cruise control − When the cruise control is being used, even if you downshift the transmission, engine braking will not be applied because the cruise control is not cancelled. For ways to decrease the vehicle speed, see “Cruise control” in this chapter.
Page 88 Your automatic transmission has a shift 3. Release the parking brake and brake lock system to minimize the possibility of CAUTION pedal. Depress the accelerator pedal incorrect operation. This means you can slowly for smooth starting. only shift out of “P” position when the (b) Using engine braking Be careful when downshifting on a brake pedal is depressed (with the ignition...
Page 89 (e) Parking NOTICE CAUTION 1. Bring the vehicle to a complete stop. zBe careful not to overrev the en- 2. Pull the parking brake lever up fully to Always keep your foot on the brake gine. Watch the tachometer to securely apply the parking brake.
Page 90 Manual transmission Low altitude NOTICE —1219 m (4000 ft) or lower If you rock your vehicle, observe the gear km/h (mph) following precautions to prevent 1 to 2 or 2 to 1 24 (15) damage to the transmission and 2 to 3 or 3 to 2 37/40* (23/25* other parts.
Page 91 Parking brake Upshift too soon or downshifting too late NOTICE will cause lugging, and possibly pinging. Regularly revving the engine to maximum Do not downshift if you are going speed in each gear will cause excessive faster than the maximum allowable engine wear and high fuel comsumption.
Page 92 Cruise control CAUTION CAUTION S To help maintain maximum con- To avoid accidental cruise control trol of your vehicle, do not use the engagement, keep the “CRUISE cruise control when driving in ON−OFF” switch off when not using heavy or varying traffic, or on slip- the cruise control.
Page 93 If the preset speed automatically cancels restore the speed set prior to cancellation. out other than for the above cases, have your vehicle checked by your Toyota deal- However, once the vehicle speed falls be- er at the earliest opportunity.
Page 95 Car audio system— Part 1 —Reference OPERATION OF INSTRUMENTS AND CONTROLS— Chapter 1−7 Car audio system and Air conditioning system Car audio system Type 2: AM·FM ETR radio/cassette Type 1−1: AM⋅FM player S Reference S Using your audio system: some basics S Using your audio system: controls and features...
Page 96 This section describes some of the basic TONE AND BALANCE YOUR RADIO ANTENNA features on Toyota audio systems. Some For details about your system’s tone and To lower a manual antenna, carefully push information may not pertain to your sys- balance controls, see the description of it down.
Page 97 —Using your audio system: controls and features " Type 1−1 Details of specific buttons, controls, and features are described in the alphabetical listing that follows.
Page 98 " Type 1−2 Details of specific buttons, controls, and features are described in the alphabetical listing that follows.
Page 99 1 2 3 4 5 6 (Preset buttons) BAL (Balance) PWR ⋅ VOL (Power ⋅ Volume) These buttons are useed to preset and This knob lets you adjust the balance be- Push “PWR ⋅ VOL” to turn the audio sys- tune in radio stations.
Page 100 Turn the knob to adjust the treble. Push the knob back into its retracted position. TUNE Tuning Your Toyota has an electronic tuning radio (ETR). Push and release the “∧” (up) or “∨” (down) side of “TUNE” to step up or down the station band.
Page 101 " Type 2 Details of specific buttons, controls and features are described in the alphabetical listing that follows.
Page 102 1 2 3 4 5 6 (Press buttons) AM ⋅ FM The Dolby NR mode reduces tape noise by about 10 dB. For best sound reproduc- These buttons are used to preset and Push “AM ⋅ FM” to switch between the AM tion, play your tapes with this button on or tune in radio stations.
Page 103 Tuning the next station up the station band, stay ward a cassette tape. Push the “REW” Your Toyota has an electronic tuning radio there for a few seconds, and then scan side to rewind a tape. “REW” will appear (ETR).
Page 104 —Car audio system operating hints Here are some common reception prob- NOTICE lems that probably do not indicate a prob- Fading—AM broadcasts are reflected by To ensure the correct audio system lem with your radio: the upper atmosphere−especially at operation: night.
Page 105 Use high−quality cassettes. S Low−quality cassette tapes can cause many problems, including poor sound, inconsistent playing speed, constant auto−reversing. They can also get stuck or tangled in the cas- sette player. S Do not use a cassette if it has been damaged or tangled or if its label is peeling off.
Page 106 Air conditioning system— —Controls 1. Air Intake Selector 2. Air Flow Selector 3. Temperature Selector 4. Fan Speed Selector 5. “A/C” Button (on some models)
Page 107 Fan speed selector For details about air flow selector settings, see the illustration after “A/C” button. Move the lever to adjust the fan speed—to the right to increase, to the left to de- crease. Temperature selector Move the lever to adjust the tempera- ture—to the right to warm, to the left to cool.
Page 108 If this happens, take your ve- hicle to a Toyota dealer for service. Air Intake selector Move the lever to select the air source. 1. Recirculate—Recirculates the air in- side the vehicle.
Page 109 —Air flow selector settings —Operating tips S To cool off your Toyota after it has been parked in the hot sun, drive with the windows open for a few minutes. This vents the hot air, allowing the air condi- tioning to cool the interior more quickly.
Page 110 Heating Air conditioning Defogging For best results, set controls to: For best results, set controls to: The inside of the windshield For best results, set controls to: Fan speed—Any setting except “OFF” Fan speed—Any setting except “OFF” Temperature— Towards COLD Fan speed—Any setting except “OFF”...
Page 111: Side Vents
—Side vents If air flow control is not satisfactory, check the side vents. The side vents may be opened or closed as shown.
Page 113: Other Equipment
Part 1 Clock OPERATION OF Once the electrical power source has been disconnected from the clock, the INSTRUMENTS AND time is automatically set to 1:00 (one o’clock). CONTROLS— Chapter 1−8 Other equipment S Clock S Cigarette lighter and ashtray The digital clock indicates the time S Glovebox with the ignition key at the “ACC”...
Page 114 Cigarette lighter and ashtray Glove box Use a Toyota genuine cigarette lighter or equivalent for replacement. CAUTION To reduce the chance of injury in case of an accident or sudden stop while driving, always push the ash- tray back in completely after using.
Page 115 Cup holder Floor mat Use a floor mat of the correct size. To use the cup holder, push it and pull CAUTION If the floor mat has a hole, then it is de- it out completely. signed for use with a locking clip. Fix the The cup holder is designed for holding Make sure the floor mat is properly floor mat and locking clip into the hole in...
Page 117 1600 km (1000 miles) can add YOUR TOYOTA To help prevent gas station mixups, your to the future economy and long life of your Toyota has a new smaller fuel tank open- vehicle: S Break−in period ing. The special nozzle on pumps with un- S Do not drive over 88 km/h (55 mph).
Page 118 FUEL TANK CAPACITY If you detect heavy knocking even when 50 L (13.2 gal., 11.0 imp. gal.) If you use gasohol in your Toyota, be using the recommended fuel, or if you sure that it is unleaded, has an octane...
Page 119 Operation in foreign countries Three−way catalytic converter If you plan to drive your Toyota in CAUTION another country... First, comply with the vehicle registration S Keep people and combustible ma- laws. terials away from the exhaust pipe Second, confirm the availability of the while the engine is running.
Page 120 S Do not remain for a long time in a quired by the Toyota Maintenance your vehicle. parked vehicle with the engine run- Schedule. For scheduled mainte- zDo not turn off the ignition while ning.
Page 121 Facts about engine oil consumption FUNCTIONS OF ENGINE OIL S Oil is also used to lubricate the stems S Keep the trunk lid closed while of the intake valves. Some of this oil is Engine oil has the primary functions of lu- driving.
Page 122 And your braking distance will CAUTION be longer. tial that the oil level be checked regularly. Toyota recommends that the oil level be Do not drive your vehicle with only ANTI−LOCK BRAKE SYSTEM checked every time you refuel the vehicle.
Page 123 Contact your Toyota dealer as lock brake system cannot overcome the soon as possible to service the vehicle. laws of physics that act on your vehicle:...
Page 124 Have your vehicle checked by your ance. Toyota dealer as soon as possible. S For better fuel economy, do not carry unneeded weight. CAUTION The brake pad wear limit indicators on...
Page 125 In an accident they manufacturuer’s plate. may injure the vehicle occupants. This is the primary identification number for your Toyota. It is used in registering the ownership of your vehicle. NOTICE Do not load the vehicle beyond the vehicle capacity weight specified in Part 8.
Page 126 Theft prevention labels Suspension and chassis (except for Canada) Your new vehicle carries theft preven- CAUTION tion labels which are approximately 56 mm (2.20 inches) by 16 mm 0.63 inch). Do not modify the suspension/ The purpose of these labels is to reduce chassis with lift kits, spacers, etc.
Page 127 Types of tires Determine what kind of tires your ve- CAUTION hicle is originally equipped with. 1. Summer tires S Do not mix summer and all season Summer tires are high−speed capability tires on your vehicle as this can tires best suited to highway driving under cause dangerous handling charac- dry conditions.
Page 129 How to start the engine— Part 3 (a) Before cranking Before starting the engine STARTING AND 1. Check the area around the vehicle be- 1. Apply the parking brake firmly. fore entering it. 2. Turn off unnecessary lights and acces- DRIVING 2.
Page 130 See “If your vehicle will not start” in Part 4. while lightly pressing the brake pedal with the parking brake pulled. If they still do not work safely, pull to the side of the road and call a Toyota dealer for assistance.
Page 131 If you are not sure about could cause the vehicle to spin or which oil to use, call your Toyota dealer− skid. he will be pleased to help. Keep the door locks from freezing. Squirt lock de−icer or glycerine into the locks to keep them from freezing.
Page 132: Trailer Towing
This product is available at your Toyota handling, performance, braking, durabili- dealer and most auto parts stores. Follow Some of the things you might put in the ve- ty and driving economy (fuel consump- the manufacturer’s directions for how...
Page 133 S The load on either the front or rear axle resulting from distribution of the gross vehicle weight on both axles must not exceed the Gross Axle Weight Rating (GAWR) listed on the Certification Label. S The trailer cargo load should be CAUTION distributed so that the tongue load S The total trailer weight...
Page 134 The chain should S Ensure that your vehicle’s tires are S Toyota recommends that the trailer cross under the trailer tongue to properly inflated. See Chapter 7−2 for...
Page 135 S Backing with a trailer is difficult and re- quires practice. Grip the bottom of the loaded so that it cannot shift. S Toyota recommends that you do not steering wheel and move your hand to tow a trailer with a new vehicle or a ve- S Check that your rear view mirrors con- the left to move the trailer to the left.
Page 136 S Avoid jerky steering and sharp turns. S In order to maintain engine braking ef- 5. Shift into first or reverse (manual) or The trailer could hit your vehicle in a ficiency, do not use fifth gear (manual “P” (automatic) and turn off the engine. tight turn.
Page 137 How to save fuel and make your vehicle last longer, too Getting more kilometers/mileage from a li- S Avoid continuous speeding up and ter/gallon of fuel is easy−just take it easy. slowing down. Stop−and−go driving S Slow down and downshift before descending steep or long downhill It will help make your vehicle last longer, wastes fuel.
Page 138 S Keep the bottom of your vehicle free from mud, etc. This not only lessens weight but also helps prevent corrosion. S Keep your vehicle tuned−up and in top shape. A dirty air cleaner, carbu- retor out of adjustment, improper valve clearance, dirty plugs, dirty oil and grease, brakes not adjusted, etc.
Page 139 If the light is O.K., but the engine still will S If you lose your keys not start, it needs adjustment or repair. Call a Toyota dealer or qualified repair shop. NOTICE Do not pull− or push−start the vehicle.
Page 140 CAUTION is correct. If the engine still will not start, it needs ad- justment or repair. Call a Toyota dealer or S Batteries contain sulfuric acid qualified repair shop for assistance. which is poisonous and corrosive.
Page 141 JUMP STARTING PROCEDURE 1. If the booster battery is installed in another vehicle, make sure the ve- hicles are not touching. Turn off all un- necessary lights and accessories. 2. If required, remove all the vent plugs from the booster and discharged bat- teries.
Page 142 If your engine stalls while driving 5. Start your engine in the normal way. If your engine stalls while driving… After starting, run it at about 2000 rpm 1. Reduce your speed gradually, keeping for several minutes with the accelera- a straight line.
Page 143 You should have it checked as Wait until the steam subsides before coolant is leaking, stop the engine im- soon as possible at your Toyota deal- opening the hood. If there is no coolant mediately. Call a Toyota dealer for as- boiling over or steam, leave the engine sistance.
Page 144 If you have a flat tire— 1. Reduce your speed gradually, keeping S Stop the vehicle on a level place a straight line. Move cautiously off the and chock the wheel diagonally road to a safe place well away from the opposite being traffic.
Page 145 CAUTION resulting in damage. S The compact spare tire was de- signed especially for your Toyota. 1. Get the tool bag, jack, jack handle Do not use it on any other vehicle. and spare tire. S Do not exceed 80 km/h (50 mph)
Page 146 —Blocking the wheel When removing the jack, turn the joint by To remove the spare tire: 2. Block the wheel diagonally oppo- hand towards the CONTRACT direction 1. Loosen the nut and remove it. site the flat tire to keep the vehicle until the jack is free.
Page 147 —Removing wheel ornament —Loosening wheel nuts 3. Remove the wheel ornament. 4. Loosen all the wheel nuts. Skip this step if your vehicle is equipped Always loosen the wheel nuts before rais- with aluminum wheels. ing the vehicle. Pry off the wheel ornament, using the bev- The nuts turn counterclockwise to loosen.
Page 148: Positioning The Jack
—Positioning the jack —Raising your vehicle CAUTION Never get under the vehicle when the vehicle is supported by the jack alone. 5. Position the jack at the correct jack 6. After making sure that no one is in point as shown. the vehicle, raise it high enough so that the spare tire can be installed.
Page 149: Changing Wheels
—Changing wheels —Reinstalling wheel nuts Before putting on wheels, remove any 7. Remove the wheel nuts and change 8. Reinstall all the wheel nuts finger corrosion on the mounting surfaces with a tires. tight. wire brush or such. Installation of wheels Lift the flat tire straight off and put it aside.
Page 150 —Lowering your vehicle —Reinstalling wheel ornament CAUTION When lowering the vehicle, make sure all portions of your body and all other persons around will not be injured as the vehicle is lowered to the ground. 9. Lower the vehicle completely and 10.
Page 151 11. Check the air pressure of the If towing is necessary, we recommend you to have it done by your Toyota replaced tire. dealer or a commercial tow truck ser- Adjust the air pressure to the specification vice.
Page 152 (a) Towing with wheel lift type truck S Automatic transmission: Use a towing dolly under the front From front—Release the parking brake. wheels. NOTICE NOTICE When lifting wheels, take care to ensure adequate ground clearance Never tow vehicle with for towing at the opposite end of the automatic transmission from the raised vehicle.
Page 153: Emergency Towing
NOTICE If towing is necessary, we recommend only cable chain you to have it done by your Toyota specifically intended for use in dealer or a commercial tow truck ser- vice. towing vehicles. Securely fasten the If towing service is not available in an...
Page 154 If you cannot shift automatic If you lose your keys transmission selector lever Many Toyota dealers can make a new key if you can give them the key num- ber. See the suggestion given in “Keys” in Chapter 1−2. If your keys are locked in the vehicle and...
Page 155: Appearance Care
Now, it is up to you. Proper CARE S High temperatures will cause corro- care of your Toyota can help ensure long− sion to those components of the ve- term corrosion prevention. hicle which are prevented from quick−...
Page 156 See “Washing and waxing your Toyota” instructions. Use a soft cotton mit and to resist corrosion. Your Toyota dealer will for more tips. keep it wet by dipping it frequently into be happy to assist in supplying and instal- Check the condition of your vehicle’s...
Page 157 Toyota through an placed in a high heat paint waxing automatic car wash. booth. High temperatures could 3. Rinse thoroughly — dried soap can damage the bumpers.
Page 158 Cleaning the interior NOTICE NOTICE CAUTION solvent, thinner, Do not use dye or bleach on the Do not wash the vehicle floor with gasoline or window cleaner on the belts−it may weaken them. water, or allow water to get into the interior.
Page 159 Air conditioning control panel, car au- dio, instrument panel, console panel, If you have any questions about the and switches cleaning of your Toyota, your local Toyota dealer will be pleased to Use a soft damp cloth for cleaning. answer them.
Page 161: Vehicle Maintenance
These checks or inspections can be done er’s Guide, Owner’s Manual Supple- either by yourself or a qualified technician, ment or Warranty Booklet for complete or if you prefer, your Toyota dealer will be warranty information. pleased to do them at a nominal cost.
Page 162 They learn to work on Booklet for the details. to your Toyota dealer or a qualified service Toyotas before they work on your vehicle, shop immediately. It is recommended rather than while they are working on it.
Page 163 Tire surface and wheel nuts Lights Accelerator pedal Check the tires carefully for cuts, damage Make sure the headlights, stop lights, tail Check the pedal for smooth operation and or excessive wear. See Chapter 7−2 for lights, turn signal lights, and other lights uneven pedal effort or catching.
Page 164 Does your vehicle need repairing? IN THE ENGINE COMPARTMENT Power steering fluid level Be on the alert for changes in perfor- mance, sounds, and visual tip−offs that in- Items listed below should be checked Check the level through the reservoir. The from time to time , e.g.
Page 165 If you notice any of these clues, take your vehicle to your Toyota dealer as soon as possible. It probably needs adjustment or repair. CAUTION Do not continue driving with the vehicle unchecked. It could result in serious vehicle damage and...
Page 167 Part 7 DO−IT−YOURSELF MAINTENANCE— Chapter 7−1 Introduction S Engine compartment overview S Fuse locations S Do−it−yourself service precautions S Parts and tools...
Page 168 Engine compartment overview (type A)
Page 169 Engine compartment overview (type B)
Page 170 Fuse locations...
Page 171 Read the sepa- compartment—the engine, radia- if the engine coolant temperature rate Toyota Warranty statement for details tor, exhaust manifold, power is high and/or the air conditioning and suggestions. steering fluid reservoir and spark is on.
Page 172 Remember all Toyota parts are Do not dispose of used oil and fil- the transmission and transfer ter in household trash, in sewers designed in metric sizes, so your tools could be damaged.
Page 173 Tools: Tools: Tools: S Rag or paper towel S Warm water S Screwdriver S Baking soda S Funnel (only for adding fluid) S Wrench S Grease Checking power steering fluid S Conventional wrench (for terminal Parts (if level is low): clamp bolts) S Automatic transmission fluid S Coin (for vent plugs)
Page 175: Engine And Chassis
Part 7 Checking the engine oil level DO−IT−YOURSELF If the oil level is below or only slightly above the low level line, add engine oil MAINTENANCE— of the same type as already in the en- gine. Remove the oil filter cap and add engine Chapter 7−2 oil in small quantities at a time, checking the dipstick.
Page 176 ENGINE OIL SELECTION Use API SH, “Energy−Conserving II” mul- tigrade engine oil or ILSAC multigrade en- gine oil. Recommended viscosity (SAE): Oil identification marks The ILSAC (International Lubricant Stan- Either or both API registered marks are dardization and Approval Committee) added to some oil containers to help Certification Mark is displayed on the front you select the oil you should use.
Page 177 So Do not use alcohol type antifreeze If you can find no leak, have your Toyota be sure to keep the reservoir filled. or plain water alone. dealer test the cap pressure and check for...
Page 178: Checking Power Steering Fluid
Checking power steering fluid If the level is low, add SAE J1703 or c. Reinstall the filler cap. FMVSS No. 116 DOT 3 brake fluid to the d. Remove the filler cap again and look at brake reservoir. the fluid level. If the fluid is cold, the level Remove and replace the reservoir covers should be in the “COLD”...
Page 179: Checking Tire Pressure
The passenger and luggage If a tire frequently needs refilling, have it weight should be located so that the checked by your Toyota dealer. vehicle is balanced. Keep your tire pressures at the proper The following instructions for check- S Be sure to reinstall the tire inflation level.
Page 180 Any tires which are over six years old must be checked by a qualified techni- Toyota recommends all four tires, or at cian even if damage is not obvious. least both of the front or rear tires be...
Page 181 Do not use tires other than those men- tioned above. Do not install studded tires To equalize tire wear and help extend without first checking local regulations for tire life, Toyota recommends that you possbile restrictions. rotate your tires every 12000 km (7500 SNOW TIRE INSTALLATION miles).
Page 182 NOTICE Correct replacement wheels are available fore installing chains. at your Toyota dealer. Do not attempt to use a tire chain on CHAIN INSTALLATION A wheel of a different size or type may ad-...
Page 183 S When using tire chains, be careful not signed for a tubeless tire. to damage the aluminum wheels. S Use only the Toyota wheel nuts and wrench designed for your aluminum wheels. S When balancing your wheels, use only Toyota balance weights or equivalent and a plastic or rubber hammer.
Page 185: Electrical Components
Checking battery condition— Part 7 —Precautions DO−IT−YOURSELF S If electrolyte gets on your skin, CAUTION thoroughly wash the contact area. MAINTENANCE— If you feel pain or burning, get BATTERY PRECAUTIONS medical attention immediately. S If electrolyte gets on your clothes, The battery produces flammable Chapter 7−3 there is a possibility of its soaking...
Page 186 —Checking battery exterior —Checking battery fluid There are two types of batteries: Main- NOTICE tenance type and non−maintenance zBe sure the engine and all acces- type. sories are off before performing A non−maintenance battery has “MAIN- maintenance. TENANCE FREE BATTERY” on its top. A zWhen checking the battery, re- maintenance type battery does not have move the ground cable from the...
Page 187 Type A Type B GREEN BLUE Good Charging necessary. DARK WHITE Have battery checked by your Toyota dealer. CLEAR or LIGHT Have battery checked YELLOW by your Toyota dealer. NOTICE CHECKING BY THE FLUID LEVEL CHECKING BY THE HYDROMETER Do not refill the battery with water.
Page 188 Battery recharging precautions During recharging, the battery is pro- NOTICE ducing hydrogen gas. Do not overfill the cells. Excess Therefore, before recharging: electrolyte could squirt out of the 1. Maintenance type batteries—Remove battery during heavy charging, the vent plugs. causing corrosion or damage. 2.
Page 189: Checking And Replacing Fuses
Checking and replacing fuses NOTICE Never recharge the battery while the engine is running. Also, be sure all accessories are turned off. If the headlights or other electrical components do not work, check the fuses. If any of the fuses are blown, they must be replaced.
Page 190: Adding Washer Fluid
It is a good idea to purchase a set of spare fuses and keep them in your vehicle for emergencies. If the new fuse immediately blows out, there is a problem with the electrical sys- tem. Have your Toyota dealer correct it as soon as possible.
Page 191 The following illustrations show how to Headlights 9006 Light bulbs Bulb Type gain access to the bulbs. When replacing (outer bulb) a bulb, make sure the ignition switch and Parking and front Front turn signal 1156 light switch are off. Use bulbs with the side marker lights lights wattage ratings given in the table.
Page 192 Replacing light bulbs— —Headlights 1. Open the hood. LEFT SIDE HEADLIGHT: Remove the clip and take out the air cleaner duct.
Page 193 If the connector is tight, wiggle it. To install a bulb, align the tabs of the bulb socket with the cutouts of the mounting hole. Aiming is not necessary after replacing the bulb. When aiming adjustment is nec- essary, contact your Toyota dealer.
Page 194 —Parking and front side —Front turn signal lights marker lights Use a Philips−head screwdriver. Use a Philips−head screwdriver.
Page 195 —Rear turn signal, stop and tail, rear side marker, and back−up lights Use a wrench. Remove and install the cover clips as shown in the following illustrations.
Page 196 —High mounted stoplight Use a Philips−head screwdriver. a: Rear turn signal light Remove and install the cover clips as b: Stop and tail light shown in the following illustrations. c: Rear side marker, stop and tail light d: Back−up light...
Page 197 Remove the bolts.
Page 198 —License plate lights —License plate lights (type A) (type B)
Page 200: Specifications
Part 8 Dimensions and weight Engine SPECIFICATIONS Overall length mm (in.) 4370 (172.0) Model: Overall width mm (in.) 1685 ( 66.3) 4A−FE and 7A−FE S Dimensions and weight Overall height mm (in.) 1380 ( 54.3)* Type: S Engine Wheelbase mm (in.) 2465 ( 97.0) 4 cylinder in line, 4 cycle, gasoline Front tread mm (in.) 1460 ( 57.5)
Page 201 Fuel Service specifications Fuel type: ENGINE Oil grade: Unleaded gasoline, Research Oc- API SH, “Energy−Conserving II” multi- Valve clearance (engine cold), mm (in.) grade engine oil or ILSAC multigrade tane Number 91 (Octane rating 87) or Intake 0.15⎯0.25 (0.006⎯0.010) higher engine oil is recommended.
Page 202 7A−FE engine Charging rates: AUTOMATIC TRANSAXLE Non−maintenance battery (3−speed type) HARRISON RADIATOR 5 A max Fluid capacity (drain and refill), Manual transmission Maintenance type battery L (qt., Imp. qt.): 6.2 (6.6, 5.5) Quick charge 15 A max Up to 2.5 (2.6, 2.2) Automatic transmission Slow charge 5 A max...
Page 203 Tires Fuses Parking brake adjustment when pulled Tire size: with the force of 196 N (20kgf, 44lbf): Spare tire 4—7 clicks T115/70D14 Fluid type: T135/70D15 SAE J1703 or FMVSS No. 116 DOT 3 Except spare tire STEERING P175/65R14 Wheel freeplay: P185/65R14 Less than 30 mm (1.2 in.) Tire pressure, kPa (kgf/cm...
Page 204 9. GAUGE 10 A: Gauges and meters, 14.FAN−I/UP 7.5 A: Multiport fuel injec- 5. DEFOG−I/UP 7.5 A: Multiport fuel in- service reminder indicators (except dis- tion system/sequential multiport fuel in- jection system/sequential multiport fuel charge and open door warning lights), injection system jection system back−up light, air conditioning system,...
Page 205 Fuses (type C) 35. AM1 40 A: “CIG & RADIO”, “GAUGE”, “TURN”, “ECU−IG”, “WIP”, “DEF” and “OBD” fuses 36. ALT 100 A: Tail lights, “DEF”, “STOP”, “ECU−B” and “AM 1” fuses 37. ABS 50 A: Anti−lock brake system 22. DRL 7.5 A: Daytime running light Fuses (type B) system 29.
Page 206 However, NHTSA can− not become involved in individual problems between you, your deal− er, or Toyota Motor Sales, U.S.A., Inc.
Page 207 A tire marked C may have poor trac- failure. quality grading. tion performance. Your Toyota dealer will help answer any Warning: The traction grade assigned to questions you may have as you read this this tire is based on braking (straight information.

Toyota 1997 Corolla Owner's Manual

Quick Links

Related Manuals for Toyota 1997 Corolla

Summary of Contents for Toyota 1997 Corolla

Table of Contents