Gazelle Bosch Active Line User Manual page 23

OBJ_BUCH-2074-002.book Page 6 Thursday, August 22, 2013 12:50 PM
Code Cause
602 Internal battery pack error
603 Internal battery pack error
605 Battery pack temperature error
605 Battery pack temperature error while
charging
606 External battery pack error
610 Batter pack voltage error
620 Charging error
640 Internal battery pack error
655 Multiple battery pack errors
656 Software version error
No display Internal error of the HMI
Power Supply of External Devices via
USB Connection
With the USB connection, it is possible to operate and charge
most devices whose power supply is possible via USB (e.g.,
various mobile phones).
Prerequisite for the charging is that the HMI and a sufficiently
charged battery pack are inserted in the eBike.
Open the protective cap 8 of the USB port on the HMI. Con-
nect the USB port of the external device to the USB socket 7
on the HMI using a standard-compliant Micro A/Micro B USB
2.0 cable. Using a USB cable that is not standard-compliant or
a cable/adapter combination can lead to damage to the HMI.
Notes on Riding with the eBike System
When does the eBike Drive Operate?
The eBike drive supports you when riding, as long as you step
into the pedals. Without pedaling, there is no assistance. The
motor output always depends on the amount of your pedaling
power.
When applying less pedaling power, the assistance or support
will be lower than when applying a lot of pedaling power. This
applies independent of the assistance Level.
Bosch eBike Systems
Corrective Measure
Restart the system. If the problem persists, contact your Bosch eBike
dealer.
Restart the system. If the problem persists, contact your Bosch eBike
dealer.
The eBike is outside of the permissible temperature range. Switch off the
eBike system and allow the drive unit to either cool down or heat up to the
permissible temperature. Restart the system. If the problem persists,
contact your Bosch eBike dealer.
Unplug the charger from the battery pack. Allow the battery pack to cool.
If the problem persists, contact your Bosch eBike dealer.
Check the wiring. Restart the system. If the problem persists, contact
your Bosch eBike dealer.
Restart the system. If the problem persists, contact your Bosch eBike
dealer.
Replace the charger. Contact your Bosch eBike dealer.
Restart the system. If the problem persists, contact your Bosch eBike
dealer.
Switch off the eBike system. Remove the battery pack and reinsert it.
Restart the system. If the problem persists, contact your Bosch eBike
dealer.
Contact your Bosch eBike dealer so that he can perform a software
update.
Restart your eBike system by switching it off and back on.
The eBike drive automatically switches off at speeds in excess
of 25 km/h. When the speed falls below 25 km/h, the drive is
automatically available again.
An exception applies to the push-assistance function, in
which the eBike can be pushed at low speed without pedal-
ling. The pedals may also rotate when the push assistance is
used.
The eBike can also be ridden as a normal bicycle without as-
sistance at any time, by either switching off the eBike system
or setting the assistance level to "OFF". The same applies
when the battery pack is empty.
Interaction of the eBike System with the Bicycle Gears
The bicycle gears should be used as with a normal bicycle,
even with eBike drive (please observe the operating instruc-
tions of your eBike).
Independent of the type of gearing, it is recommended to
briefly interrupt the pedaling while changing gears. This
makes changing gears easier and reduces the wear of the
drive train.
By selecting the right gear, you can increase the speed and
range with the same pedaling effort.
BOSCH ACTIVE LINE
English–6
0 276 001 SAI | (22.8.13)
23