Download Print this page
Audiovox PRO 9445FT Installation Manual
Audiovox PRO 9445FT Installation Manual

Audiovox PRO 9445FT Installation Manual

Pursuit series remote keyless entry

Advertisement

Quick Links

PRE-INSTALLATION NOTES:
This unit incorporates three on - board dip switches for selection of optional features. They are;
Dip Switch #1
Dip Switch #2
Dip Switch #3
This system provides a transistorized output to control the starter cut feature.
When the starter cut relay is installed, any time the doors are remotely locked, the vehicle's starting circuit is disabled.
Additionally, when the passive starter cut feature is selected (dip switch #3 On), then 30 seconds after leaving the vehicle,
the vehicle's starting circuit will be automatically disabled.
This system provides an additional hardwire remote output to control an assortment of optional upgrades. This output
is an independent channel from the transmitter, and is controlled by the (Option) button of the transmitter. It is a delayed
ground pulse (300 mA maximum), and can be used to control;
Optional Trunk Release Relay
Optional Remote Starter
Optional Window Roll Up
Optional Garage Door
Additionally, if both transmitter buttons are designated, the remote transmitter has the capability of transmitting a third
RF signal that can be used to operate a second vehicle equipped with a similar Pursuit alarm. By simultaneously
pressing both the "Lock/Unlock" button along with the "Option" button, a third function can be operated.
This system provides both (+) and (-) pulsed door lock outputs for direct connection to most OEM factory installed door
lock control relays. These outputs have a maximum current capability of 300 mA, and external relays must be used for
switching circuits requiring more than 300 mA, and with 4 or 5 wire polarity reversal door lock control circuits. The optional
AS-9159 Door Lock Interface is available to simplify the wiring of these types of circuits.
INSTALLATION OF MAJOR COMPONENTS:
CONTROLMODULE:
Select a mounting location inside the passenger compartment ( up behind the dash ), and secure it using screws,
or cable ties.
DO NOT mount the control module in the engine compartment, as it is not waterproof.
DO NOT mount the unit or route the wiring near the steering shaft, as it might become entangled, preventing proper
operation of the vehicle.
REMOTE KEYLESS ENTRY
DIP SWITCHES :
ON
Auto Lock/Unlock
Passive Lock
Passive Starter Inhibit
STARTER DISABLE:
CHANNEL 2 OUTPUT:
AS-9256
AS-9151N / AS-9075
AS-9153
AS-9154
DOOR LOCK / UNLOCK OUTPUTS:
1
Model PRO 9445FT
Installation Manual
OFF
No Auto Lock/Unlock
Active Locks
Active Starter Inhibit

Advertisement

loading

Summary of Contents for Audiovox PRO 9445FT

  • Page 1 REMOTE KEYLESS ENTRY DIP SWITCHES : Auto Lock/Unlock No Auto Lock/Unlock Passive Lock Active Locks Passive Starter Inhibit Active Starter Inhibit STARTER DISABLE: CHANNEL 2 OUTPUT: AS-9256 AS-9151N / AS-9075 AS-9153 AS-9154 DOOR LOCK / UNLOCK OUTPUTS: Model PRO 9445FT Installation Manual...
  • Page 2 VALET SWITCH: Select a mounting location for the switch that is easily accessible to the driver of the vehicle. The switch does not have to be concealed, however concealing the switch is always recommended, as this provides an even higher level of security to the vehicle. The switch is mounted by drilling a 1/4"...
  • Page 3 4 WIRE POLARITY REVERSAL and 5 WIRE ALTERNATING DOOR LOCK CONTROL CIRCUITS In these applications, the AS-9159 Door Lock Interface (or equivalent 30 Amp. automotive type relays) must be used. Refer to the Audiovox Door Lock Wiring Supplement for proper connection to these types of door lock circuits. COMPLETING THE INSTALLATION: ANTENNA WIRE : Be sure to extend the thin Black antenna wire to it's full length, and cable tie in place where it cannot be damaged.
  • Page 4 © 1998 Audiovox Corporation, Hauppauge, N.Y. 11788 1-800-645-4994 128-5393...

This manual is also suitable for:

Pro pursuit 9445ft