Table of Contents
Advertisement
Quick Links
SE RVICE MANUAL
T T e e c c h h n n i i c c a a l l D D a a t t a a
M M e e c c h h a a n n i i c c a a l l R R e e p p a a i i r r
E E l l e e c c t t r r i i c c a a l l R R e e p p a a i i r r s s
C C a a l l i i b b r r a a t t i i o o n n
F F a a u u l l t t D D i i a a g g n n o o s s i i s s
T T o o o o l l s s a a n n d d T T e e s s t t E E q q u u i i p p m m e e n n t t
P P a a r r t t s s L L i i s s t t
Page 1 of 13
Advertisement
Table of Contents
Summary of Contents for Prestige 2100 Classic
- Page 1 SE RVICE MANUAL T T e e c c h h n n i i c c a a l l D D a a t t a a M M e e c c h h a a n n i i c c a a l l R R e e p p a a i i r r E E l l e e c c t t r r i i c c a a l l R R e e p p a a i i r r s s C C a a l l i i b b r r a a t t i i o o n n F F a a u u l l t t D D i i a a g g n n o o s s i i s s...
- Page 2 T T e e c c h h n n i i c c a a l l D D a a t t a a Continuous operation, with intermittent use. Electronic system is set to hold a minimum 121°C for 16 minutes (except 210006), 126°C for 11 minutes or 134°C for 3.5 minutes when loaded with instruments.
- Page 3 M M e e c c h h a a n n i i c c a a l l R R e e p p a a i i r r s s Depressurization Valve Kit (RPI Part #KVK043) (OEM Part #219711) Circlip in valve handle.
- Page 4 M M e e c c h h a a n n i i c c a a l l R R e e p p a a i i r r s s ( ( c c o o n n t t i i n n u u e e d d ) ) Fig 2.
- Page 5 LID GASKET: Simply extract the old gasket from the lid flanges and replace with a new one. Only genuine Prestige Medical parts to be fitted. Note: No lubrication is required for the gasket. However, if the lid is difficult to put on, Vaseline (petroleum jelly) can be lightly smeared around the edge and underside of the body flanges.
- Page 6 M M e e c c h h a a n n i i c c a a l l R R e e p p a a i i r r s s ( ( c c o o n n t t i i n n u u e e d d ) ) BASE MOULDING: Place body on a flat surface upside down.
- Page 7 E E l l e e c c t t r r i i c c a a l l R R e e p p a a i i r r s s THERMAL FUSES: The thermal fuse is in the base moulding, to gain access to this part, remove the base as previously described. The thermal fuse is in the brown wire and must be replaced as a complete assembly with wires and terminals (Fig 7).
- Page 8 E E l l e e c c t t r r i i c c a a l l R R e e p p a a i i r r s s ( ( c c o o n n t t i i n n u u e e d d ) ) Disconnect display ribbon cable.
- Page 9 E E l l e e c c t t r r i i c c a a l l R R e e p p a a i i r r s s ( ( c c o o n n t t i i n n u u e e d d ) ) PRESSURE GAUGE &...
- Page 10 C C a a l l i i b b r r a a t t i i o o n n Fig 9. Fill to water level with de-ionised/distilled water (0.75L). Put on the test lid with pressure gauge and digital ther- mometer connected.
- Page 11 C C a a l l i i b b r r a a t t i i o o n n ( ( c c o o n n t t i i n n u u e e d d ) ) If this temperature is too low, turn the pot trimmer clockwise one click at a time to increase the temperature by 0.5 to 1.0°C, allow 1 to 2 minutes for the temperature to stabilise on thermometer.
- Page 12 F F a a u u l l t t D D i i a a g g n n o o s s i i s s Worn or dirty gasket Wash gasket - replace in lid If fault persists, replace with new gasket Steam or water leaking from RPI Part #KVG001...
- Page 13 Various socket adaptors to mate up with torque wrenches Long nose pliers Sharp knife SPECIAL TOOLS: Available as a tool kit, reference OEM Part #219287 for Prestige Classic 210006. M5 nut runner Air bleed push fix Potentiometer trimmer (flat bladed jewellers screwdriver).