1 Safety Precautions 1.1. General guidelines 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
2 Warning 2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatic Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec- trostatic Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistor-sand semi- conductor "chip"...
2.3. Service caution based on legal restrictions 2.3.1. General description about Lead Free Solder (PbF) The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this equipment in considering the globally environmental conservation. The normal solder is the alloy of tin (Sn) and lead (Pb).
3 Service Navigation 3.1. How to format for HDD when replacement of HDD or Main P.C.B. 3.1.1. How to escape " HDD Error " indication on GUI display. 1. When exchange HDD or Main P.C.B., the " HDD Error " screen is displayed, but, according to a following procedure, please format HDD.
3.5. (HDD/BD Drive) Service Navigation 3.5.1. HDD/BD Drive Malfunction check (Simplified Method) Perform simple quality judgement process of HDD/BD Drive according to the following operations. 1. Execute Service Mode While the power is off, press [CH UP], [REC] and [OPEN/CLOSE] keys simultaneously for five seconds. 2.
3.6. Operation check when a USB device is connected You can check the operation status (normal or abnormal) of the USB connection part of this unit easily as shown below. Connect each device to the USB terminal on the front panel and check the operation status on the TV monitor. Normal operation: Automatically displayed when the USB connection is made to a digital camera, etc.
Page 13
Main functions 1. Execute Tuner Service Mode Turn the power on to receive digital broadcasting (HD broadcasting). Press and hold [POWER] (Unit Key) and press [OPEN/CLOSE] + [REC] for 5 seconds at the same time. 2. Finishing Service Mode Method 1: After turning the unit "OFF", pull out the AC cord. Method 2: Repeat turning ON and OFF twice: P-OFF →...
Page 14
Note: Hard test result does not guarantee that problems do not exist even if the result is OK. The result is used as reference when any trouble occurs. 3.7.2. Use times and number of times of Power ON/OFF Display accumulated time of Power ON and display number of times of Power ON/OFF. *1 : Display accumulated time of Power ON Display on a 15-minute basis 00123:15 →...
Page 15
Operation procedure Preparation: Prepare a SD card to export data stored in this unit. Create the following directory on the SD card. EEPBAKSD Boot: 1. On Tuner Service Mode display Using Remote Controller, move the cursor to user’s setting information backup display position (Refer to below) on Tuner Service Mode display.
6 Installation Instructions 6.1. Taking out the Disc from BD-Drive Unit when the Disc cannot be ejected by OPEN/CLOSE button 6.1.1. Forcible Disc Eject 6.1.1.1. When the power can be turned off. 1. Turn off the power and press [STOP] [CH UP] keys on the front panel simultaneously for 5 seconds. 6.1.1.2.
7 Service Mode 7.1. Self-Diagnosis and Special Mode Setting 7.1.1. Self-Diagnosis Functions Self-Diagnosis Function provides information for errors to service personnel by "Self-Diagnosis Display" when any error has occurred. U**, H** and F** are stored in memory and held. You can check latest error code by transmitting [0] [1] of Remote Controller in Service Mode. Automatic Display on LCD will be cancelled when the power is turned off or AC input is turned off during self-diagnosis display is Error Code Diagnosis contents...
Page 23
Error Code Diagnosis contents Description Monitor Display Automatic LCD display HDMI connection error When authentication error occurs while the No display (authentication error) equipments (TV, amplifier etc.) are con- nected by HDMI. (or when there is a prob- lem with the HDMI cable) U73 display disappears when error has been solved by Power OFF/ON of connecting equipment or by...
Page 24
Error Code Diagnosis contents Description Monitor Display Automatic LCD display NO READ Disc read error *A disc is flawed or dirty. "Cannot read. *A poor quality failed to start. Please check the *The track information could not be read. disc." HARD Drive error The drive detected a hard error.
Page 25
7.1.2. Special Modes Setting Item LCD display Key operation Mode name Description Front Key Rating password The audiovisual level setting password is Open the tray, set DRIVE SELECT initialized to "Level 8". to BD, and press [REC] and [PLAY] simultaneously for 5 seconds. Service Mode Setting every kind of modes for servicing.
Page 26
Aging Overview • Record several programs onto the mounted HDD with DR mode until the recording capacity becomes full. Then play back all the recorded programs (including special playback). • When the remaining capacity becomes almost zero due to multiple recordings, the disc is formatted, recording is made onto the same disc again and playback starts.
Page 27
Sequence 0: OPEN/CLOSE of BD drive tray Press [OPEN/CLOSE] to open the tray, then inserting discs. Press [OPEN/CLOSE] to close the tray. Sequence 1: Format of the HDD Sequence 2: Details of Record/ Playback HDD: Record/ HDD: Playback Sequence 3: Detail of copying. (HDD to BD) Recorded to the BD.
Page 28
Item LCD display Key operation Mode name Description Front Key Demonstration lock/ Ejection of the disc is prohibited. *When lock the tray. When the power is on, press unlock The lock setting is effective until unlocking [STOP] and [POWER] keys simulta- the tray and not released by "Main unit ini- neously for 5 seconds in the condi- tialization"...
Page 29
7.1.3. Service Modes at a glance Service mode setting: While the power is off, press REC, CH UP and OPEN / CLOSE simultaneously for five seconds. Item LCD display Key operation Mode name Description (Remote controller key) Release Items Item of Service Mode executing is can- Press [0] [0] in service mode.
Page 30
Item LCD display Key operation Mode name Description (Remote controller key) READ SEEK Inspecting seek time of HDD to inspect per- At start Press [3] [1] in service mode. Inspection formance. * When canceling the inspection mode while executing, do "forced power-off".
Page 31
Item LCD display Key operation Mode name Description (Remote controller key) READ VERIFY Measure of access time in READ VERIFY At start Press [3] [2] in service mode. Inspection MODE of HDD. * When canceling the inspection mode while executing, do "forced power-off".
Page 32
Item LCD display Key operation Mode name Description (Remote controller key) Standard Speed Standard speed AV scan check of HDD Press [3] [6] in service mode. Scan * When canceling the inspection mode while executing, do "forced power-off". Method: Press [POWER] key on the main unit more than 4 seconds.
Page 33
Item LCD display Key operation Mode name Description (Remote controller key) HDD/BD Drive Simple Check if HDD Self-Diagnosis test was per- HDD Self-Diagnosis test start. Press [3][8] in service mode. Check formed or Drive last error occurred within 4 weeks. * If the current date or the date when the error occurred is wrong, correct judgement may not be made.
Page 34
Item LCD display Key operation Mode name Description (Remote controller key) BD Drive Last Error BD Drive error code display. 1. Error Number is displayed for 5 Press [4] [2] in service mode. *For details about the drive error code, refer seconds.
Page 35
Item LCD display Key operation Mode name Description (Remote controller key) BD-R DVD-ROM RAM (2.6GB) RAM (4.7GB) DVDR Others * is displayed the responded value from RTSC. 6. Disc Maker ID is displayed for 5 seconds. 7. Factor of Drive Error (hexadecimal) In case that the maker cannot be occurring is left displayed identified, display is black out.
Page 36
Item LCD display Key operation Mode name Description (Remote controller key) : Error occurring disc situation Laser power confirmation Drive state is judged based on difference Measuring stars (Measuring in pro- into between laser power value at shipping and cess). BD Drive in service mode.
Page 37
Item LCD display Key operation Mode name Description (Remote controller key) CEC (H) output Check of the CEC terminal high output of When the check is OK. Press [5] [5] in service mode. HDMI. When the check is NG. CEC (L) output Check of the CEC terminal low output of When the check is OK.
Page 38
Item LCD display Key operation Mode name Description (Remote controller key) Tray OPEN/CLOSE Test The tray is opened and closed repeatedly. Press [9] [1] in service mode *When releasing this mode, press the [POWER] button. "*" is number of open/close cycle times.
8 Service Fixture & Tools Part Number Description Compatibility RFKZ0557 Extension FFC (Digital P.C.B. - AV IO P.C.B. / 11 Pin) RFKZ0216 Extension Cable (Digital P.C.B. - Main P.C.B. / 23 Pin) Same as BS750/BS850EG Series RFKZ0323 Extension Cable (Digital P.C.B. - Main P.C.B. / 9 Pin) Same as BS750/BS850EG Series RFKZ0215 Extension Cable (Front (R) P.C.B.
9 Disassembly and Assembly Instructions 9.1. Unit 9.1.1. Disassembly Flow Chart The following chart is the procedure for disassembling the casing and inside parts for internal inspection when carrying out the ser- vicing. To assemble the unit, reverse the steps shown in the chart below. 9.1.2.
9.1.3. Top Case 9.1.5. Front (L) P.C.B., Front (R) P.C.B. 1. Remove 2 Screws (A) and 3 Screws (B). 1. Remove 4 Screws (A) to remove the Front (L) and Front 2. Slide the Top Case rearward and open the both ends at (R) P.C.B.
Page 42
9.1.6. BD Drive 2. Attach the Tray Door Ass’y in order from • Insert the Long shaft in the hole. 1. Remove 4 Screws (A), BD Power Cable and Drive FFC to • Insert the shaft in the hole. remove BD Drive. CAUTION: 3.
Page 43
CI P.C.B. 9.1.8. 9.1.7. 1. Disconnect 2 FFCs. 2. Remove 3 Screws (A) to remove CI P.C.B. 1. Disconnect the Fan connector, remove 5 Screws (A), CI PCB Angle, SATA Signal Cable and SATA Power Cable to remove HDD.
Page 44
2. Put HDD up and down inversely so as not to give a shock Rear Panel, Fan Motor 9.1.9. to HDD. 9.1.9.1. Only Fan Motor 1. Remove CI PCB Angle. (Refer to 9.1.8. HDD section) 2. Remove 2 Screws (A). 3.
Page 45
9.1.10. AV IO P.C.B. S2 Tuner Pack P.C.B. 9.1.11. 1. Disconnect 2 FFCs. 1. Remove 2 Washers. 2. Remove 2 Screws (A) to remove AV IO P.C.B. 2. Pull up the S2 Tuner Pack P.C.B. in the direction of the arrow with pulling the Claw of PCB Holder.
Page 46
Main P.C.B. Digital P.C.B. 9.1.12. 9.1.13. 1. Disconnect 3 FFCs. 2. Disconnect 3 connectors. 3. Remove 2 Screws (A) to remove CI PCB Angle B and Digital P.C.B. 1. Disconnect BD Power Cable. 2. Disconnect 3 connectors. 3. Remove 3 Screws (A) and Front Angle to remove Main P.C.B.
9.2. BD Drive 3. Pull the Tray to the direction of arrow until it can be. 9.2.1. Upper Base Ass’y 1. Remove 4 Screws (A), and push the Hook in. 4. Insert the Paper Clip into the hole in about 45 degree. Press the dotted part in the arrow direction and tilt the Paper Clip in lower left direction to pry the rib at the back.
Page 48
5. Insert the Paper Clip into the Tray as below figure, lift up 9.2.3. Pulley Gear, Belt the lever using the Paper Clip while pushing the dotted 1. Perform the step "9.2.2. Tray". point of the Tray. 2. Push the post to the direction of arrow by using the slot- And remove the Tray.
Page 49
9.2.4. Slide Cam 7. Remove the Slide Cam. 1. Perform the step "9.2.3. Pulley Gear, Belt". 2. Remove the Sheet. 3. Open the connector lock, and disconnect the 4 FFCs. 4. Remove 2 Screws (B) and the Drive P.C.B. 9.2.5. Mid Gear, Drive Gear and Loading Motor 1.
Page 51
9.2.7. How to Clean the Lens of Optical Pick-UP Follow the "9.2.1. Upper Base Ass’y"...
Page 52
Service hint If a defective phenomenon is "NO READ", please try to clean TT (turn table) in the drive in according to the following procedure. 1. Blow off dust on TT by a blower. (Air must not blow to it strongly.) 2.
10 Measurements and Adjustments 10.1. Service Positions Note: For description of the disassembling procedure, see the section 9. 10.1.1. Checking and Repairing of Main P.C.B.
Page 54
10.1.2. Checking and Repairing of BD Drive...
Page 55
10.1.3. Checking and Repairing of AV IO P.C.B.
10.2. Caution for Replacing Parts 10.2.1. Items that should be done after replacing parts * Note1: 10.2.2. Notice after replacing Digital P.C.B. or BD Drive Formatting the HDD is unnecessary after replacing Digital P.C.B. or BD Drive. [TM AV1] is displayed, once power OFF, and power ON again.
No abnormality should be seen in the picture, sound or operation. the BD-RE (V2.0) and RAM discs. *Panasonic BD-RE (V2.0) and DVD-RAM discs should be used when copying and playback. If a problem is caused by a VCD, DVD-R, DVD-Video, Audio-CD, or No abnormality should be seen in the picture, sound or operation.
"Standard-Playback" mode when there is no specify mode is mentioned. Model No. DMR-BS785EG 4.Although the voltage and waveform available on here is measured with standard frame, it may be differ from actual measurement due to modification of circuit and so on.
S2. Voltage and Waveform Chart Note) Indicated voltage values are the standard values for the unit measured by the DC electronic circuit tester (high-impedance) with the chassis taken as standard. Therefore, there may exist some errors in the voltage values, depending on the internal impedance of the DC circuit tester. S2.1.
IC14301 Q14301 (DC-DC CONVERTER) (REG.X SW+5.9V) X SW +5.9V EXT UP SEL SYNC Q10102 OSC 9 (FEED BACK) EXT LO 11 Q14302 (REG.X SW+5.9V) QR10101 (S P SAVE :OFF) QR10103 COLD S P SAVE :OFF) DMR-BS785EG/BS885EG Power Supply Block Diagram(1/2)
FROM TIMER BLOCK SECTION P6701 P58004 V OUT 3 DIGITAL P.C.B. P STANDBY IC1611 (REG. FL + LCD+5V ) FROM TIMER BLOCK SECTION V IN LCD+5V P7501 P7202 V OUT 4 FRONT(R) FL BSB ON P.C.B. IC59501- DMR-BS785EG/BS885EG Power Supply Block Diagram(2/2)
< B > BIAS AV2 G P3002 P58003 GREEN < RGB CPSV > (EXT) AV2 B AV2 G AV2 G BLUE CLAMP AV2 V/Y VIDEO/Y AV2 B AV2 B CLAMP AV2 V/Y AV2 V/Y CLAMP DMR-BS785EG/BS885EG Analog Video Block Diagram...
AV2 LIN BUFF. Bias (EXT) AUDIO IN ch1(L) P3001 P58007 AV1 L OUT MUTE Mute JK4801 COAXIAL AUDIO OUTPUT JACK Q4801 COAXIAL JK4901 OPTICAL DIGITAL AUDIO OUT JACK FROM P58007 P3001 OPTIEC DIGITAL BLOCK SECTION DMR-BS785EG/BS885EG Analog Audio Block Diagram...
S3.4. Timer Block Diagram DIGITAL P.C.B. IC59501 (TIMER) P6701 P58004 HDD PFAIL HDD PFAIL L DR P ON P6703 P58006 DR P ON SP SAVE P6703 P58006 SP SAVE FROM/TO POWER SUPPLY FL BSB ON H P6703 P58006 BLOCK SECTION FL BSB ON H IC59505 AU ON H...
JK59001 HSOSYNC HSOSYNC CS1- CS1- (LAN) DASP_NC1 DASP_NC1 HSOCLK HSOCLK CI P.C.B. DIGITAL P.C.B. P1601 DR 12V DR 12V DR GND DR GND DR GND DR GND DMR-BS785EG/BS885EG BD DRIVE DR 5V DR 5V MAIN P.C.B. Interconnection Schematic Diagram S-11...
S4.2. Power (P) Schematic Diagram DMR-BS785EG/BS885EG Power Section (Main P.C.B. (1/2)) Schematic Diagram (P) CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE 2A 250V FUSE. ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQUES 2A 250V D' INCENDIE N' UTILISERQUE DES FUSIBLE DE MÉME TYPE 2A 250V.
S6. Abbreviation INITIAL/LOGO ABBREVIATIONS A0~UP ADDRESS ACLK AUDIO CLOCK AD0~UP ADDRESS BUS ADATA AUDIO PES PACKET DATA ADDRESS LATCH ENABLE AMUTE AUDIO MUTE AREQ AUDIO PES PACKET REQUEST AUDIO RF SERVO AMP INVERTED INPUT SERVO AMP OUTPUT ASYNC AUDIO WORD DISTINCTION SYNC BIT CLOCK (PCM) BCKIN BIT CLOCK INPUT...
Page 117
INITIAL/LOGO ABBREVIATIONS DREQ DATA REQUEST DRESP DATA RESPONSE DIGITAL SERVO CONTROLLER DSLF DATA SLICE LOOP FILTER DIGITAL VIDEO DISC ERROR TORQUE CONTROL ERROR TORQUE CONTROL REFERENCE ENCSEL ENCODER SELECT ETMCLK EXTERNAL M CLOCK (81MHz/40.5MHz) ETSCLK EXTERNAL S CLOCK (54MHz) FBAL FOCUS BALANCE FCLK FRAME CLOCK...
Page 118
INITIAL/LOGO ABBREVIATIONS PWMCTL PWM OUTPUT CONTROL PWMDA PULSE WAVE MOTOR DRIVE A PWMOA, B PULSE WAVE MOTOR OUT A, B READ ENABLE RFENV RF ENVELOPE RF PHASE DIFFERENCE OUTPUT (CD-ROM) REGISTER SELECT RSEL RF POLARITY SELECT RESET RESERVE SBI0, 1 SERIAL DATA INPUT SBO0 SERIAL DATA OUTPUT...
Page 119
INITIAL/LOGO ABBREVIATIONS TPSO OP AMP OUTPUT TPSP OP AMP INVERTED INPUT TRCRS TRACK CROSS SIGNAL TRON TRACKING ON TRSON TRAVERSE SERVO ON VBLANK V BLANKING COLLECTOR POWER SUPPLY VOLTAGE VCDCONT VIDEO CD CONTROL (TRACKING BALANCE) DRAIN POWER SUPPLY VOLTAGE VIDEO FEED BACK VREF VOLTAGE REFERENCE SOURCE POWER SUPPLY VOLTAGE...
S7. Replacement Parts List Definition of Parts supplier: 1. Parts marked with [SPC] in the remarks column are supplied from AVC-CSC-SPC. Others are supplied from PAVCSK. S-61...
Page 121
DMR-BS785EGK/S, DMR-BS885EGK vol.1 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks D14301 B0JCMD000014 DIODE 1 E.S.D. RFKB71181LT MAIN P.C.B. 1 (RTL) E.S.D. BS785EGK/S D14302 B0JCMD000014 DIODE 1 E.S.D. RFKB71181KT MAIN P.C.B. 1 (RTL) E.S.D. BS885EGK VEP73177B AV IO P.C.B.
Page 122
DMR-BS785EGK/S, DMR-BS885EGK vol.1 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks R7511 ERJ3GEY0R00V 1/10W 0 ZA15301 K9ZZ00001279 EARTH PLATE R7512 ERJ3GEY0R00V 1/10W 0 ZA15302 K9ZZ00001279 EARTH PLATE R7513 ERJ3GEY0R00V 1/10W 0 R7518 ERJ3GEY0R00V 1/10W 0 ZJ3801 K9ZZ00001279...
Page 123
DMR-BS785EGK/S, DMR-BS885EGK vol.1 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks C4064 F2A1C470B174 16V 47U 1 BS885EGK R3904 ERJ3GEYJ103V 1/10W 10K C4064 F2A1E470A205 25V 47U 1 BS785EGK/S R3905 ERJ3GEYJ473V 1/10W 47K C4072 F2A1E221A643 25V 220U 1 BS885EGK R3906...
Page 124
DMR-BS785EGK/S, DMR-BS885EGK vol.1 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks W215 ERJ3GEY0R00V 1/10W 0 IC96201 C0DBZHE00024 IC 1 E.S.D. W216 ERJ6GEY0R00V 1/8W 0 IC96202 C1AB00003158 IC 1 E.S.D. W217 ERJ3GEY0R00V 1/10W 0 IC96401 C0JBAH000138 IC 1 E.S.D.
Page 125
DMR-BS785EGK/S, DMR-BS885EGK vol.1 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks R96062 ERJ2GEJ560X 1/16W 56 R96265 ERJ2GEJ223X 1/16W 22K R96063 ERJ2GEJ103X 1/16W 10K R96266 ERJ2GEJ223X 1/16W 22K R96064 ERJ2GEJ103X 1/16W 10K R96267 ERJ2GEJ103X 1/16W 10K R96065...
Page 126
DMR-BS785EGK/S, DMR-BS885EGK vol.1 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks RX96420 D1H83304A024 RESISTOR-RESISTOR ERJ6GEY0R00V 1/8W 0 RX96421 D1H83304A024 RESISTOR-RESISTOR RX96422 D1H83304A024 RESISTOR-RESISTOR ZB7201 RMN0945 LCD HOLDER RX96423 D1H83304A024 RESISTOR-RESISTOR RX96424 D1H83304A024 RESISTOR-RESISTOR RX96425 D1H83304A024 RESISTOR-RESISTOR RX96426...
Page 127
DMR-BS785EGK/S, DMR-BS885EGK vol.1 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks C8218 F1H1C104A071 16V 0.1U IC8109 C0DBEHE00005 IC 1 E.S.D. C8220 F1H1E223A002 25V 0.022U IC8110 C0DBEYG00002 IC 1 E.S.D. C8221 F1H1A105A036 10V 1U C8222 F1H1A105A036 10V 1U L8101...
Page 128
DMR-BS785EGK/S, DMR-BS885EGK vol.1 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks R8170 ERJ3GEYJ220V 1/10W 22 R8171 ERJ3GEYJ220V 1/10W 22 R8172 ERJ3GEYJ220V 1/10W 22 R8173 ERJ3GEYJ220V 1/10W 22 R8174 ERJ3GEYJ220V 1/10W 22 R8175 ERJ3GEYJ220V 1/10W 22 R8176 ERJ3GEY0R00V 1/10W 0...
Page 129
DMR-BS785EGK/S, DMR-BS885EGK vol.1 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks RHD30111-31 SCREW VEP73177B AV IO P.C.B. 1 (RTL) E.S.D. BS785EGK/S RHD30111-31 SCREW VEP73177A AV IO P.C.B. 1 (RTL) E.S.D. BS885EGK RHD30111-31 SCREW RFKB71181LT MAIN P.C.B.
Page 130
DMR-BS785EGK/S, DMR-BS885EGK vol.1 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks VEP70352A FRONT (L) P.C.B. 1 (RTL) E.S.D. VEP70353AX FRONT (R) P.C.B. 1 (RTL) E.S.D. 202-1 RKW0899-Q LCD FILTER 202-2 VEE1H89 FRONT CABLE RYP1573D-K FRONT PANEL ASS'Y1 1 BS785EGK...
Page 131
DMR-BS785EGK/S, DMR-BS885EGK vol.1 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks VDG1713-J PULLEY GEAR VDG1714 MIDDLE GEAR VDG1715-J DRIVE GEAR VEM0881 LOADING MOTOR UNIT VHD1653-1 SCREW VMD6134 MECHA SHASSIS VMD5749 SLIDE CAM VMG1809 BELT VMT1982...
Page 132
DMR-BS785EGK/S, DMR-BS885EGK vol.1 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks RJA0043-1C POWER CORD 1 BS785EGK/S K2CR2DA00004 POWER CORD 1 BS885EGK XZB15X30A04Z ACCESSORY BAG 1 BS785EGK/S RPF0501 ACCESSORY BAG 1 BS885EGK N2QAYB000474 REMOTE CONTROLLER A4-1 100300037800 BATEERY COVER...