TABLE OF CONTENTS 1 Safety Precaution -------------------------------------------------3 1.1. General Guidelines ----------------------------------------3 1.2. Leakage Current Cold Check ---------------------------3 1.3. Leakage Current Hot Check (See Figure 1.)--------3 1.4. How to Discharge the Capacitor on Power/Top PCB------------------------------------------------------------4 2 Warning --------------------------------------------------------------5 2.1. Prevention of Electro Static Discharge (ESD) to ElectrostaticallySensitive (ES) Devices -----------5 2.2.
1 Safety Precaution 1.1. General Guidelines 1. IMPORTANT SAFETY NOTICE There are special components used in this equipment which are important for safety. These parts are marked by in the Schematic Diagrams, Circuit Board Layout, Exploded Views and Replacement Parts List. It is essen- tial that these critical parts should be replaced with manu- facturer’s specified parts to prevent X-RADIATION, shock, fire, or other hazards.
1.4. How to Discharge the Capacitor on Power/Top PCB CAUTION: 1. Be sure to discharge the capacitor on POWER/TOP PCB. 2. Be careful of the high voltage circuit on POWER/TOP PCB when servicing. [Discharging Procedure] 1. Refer to the disassemble procedure and Remove the necessary parts/unit. 2.
2 Warning 2.1. Prevention of Electro Static Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec- trostatically Sensitive (ES) Devices. The following techniques should be used to help reduce the incidence of component damage caused by electro static discharge (ESD).
A replacement fuse cover can be purchased from your local Panasonic Dealer. If the fitted moulded plug is unsuitable for the socket outlet in your home then the fuse should be removed and the plug cut off and disposed of safety.
2.4. How to Replace the Lithium Battery 2.4.1. Replacement Procedure 1. Remove the POWER/TOP PCB. (Refer to Disassembly Procedures.) 2. Remove the Lithium battery (Ref. No. “Z9901” at component side of POWER/TOP PCB) and then replace it into new one. NOTE: This Lithium battery is a critical component.
Page 8
NOTE: Above caution is applicable for a battery pack which is for DMC-TZ1 series, as well.
3 Service Navigation 3.1. Introduction This service manual contains technical information, which allow service personnel’s to understand and service this model. Please place orders using the parts list and not the drawing reference numbers. If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual. 3.2.
How to Define the Model Suffix (NTSC or PAL model) There are six kinds of DMC-TZ1, regardless of the colours. • a) DMC-TZ1S • b) DMC-TZ1PP • c) DMC-TZ1EB/EF/EG/EGM/GN • d) DMC-TZ1EE • e) DMC-TZ1GT • g) DMC-TZ1PL/GC/GK/SG (DMC-TZ1S is exclusively Japan domestic model.) What is the difference is that the “INITIAL SETTINGS”...
(When the “GT” or “GK” model suffix is selected, the display shows “PLEASE SET THE CLOCK” in Chinese.) 1) As for your reference Default setting condition is given in the following table. • Default setting (After “INITIAL SETTINGS”) MODEL a) DMC-TZ1S b) DMC-TZ1PP/PL c) DMC-TZ1EB/EE/EF/EG/EGM/GC/GN/SG d) DMC-TZ1GK e) DMC-TZ1GT VIDEO OUTPUT LANGUAGE NTSC...
6 Service Mode 6.1. Error Code Memory Function 1. General description This unit is equipped with history of error code memory function, and can be memorized 32 error codes in sequence from the latest. When the error is occurred more than 32, the oldest error is overwritten in sequence. The error code is not memorized when the power supply is shut down forcibly (when the unit is powered on by the battery, the battery is pulled out) because the error code is memorized to FLASH ROM when the unit is powered off.
Page 15
• 4. How to read the error code: One error code is displayed for 8 bit, the contents of error codes is indicated the table as shown below. Attribute Main item Sub item LENS Lens drive C.B./Zoom Zoom Focus Lens Error code High 4 bits Low 4 bits 1800...
Page 16
Attribute Main item Sub item LENS Adj.History HARD VENUS A/D Flash FLASH ROM FLASH ROM (EEPROM (EEPROM Area) Area) SYSTEM SOFT Reset Card Card CPU, Stop ASIC hard Operation Power on Zoom Zoom • 5. How to returned to Normal Display: Turn the power off and on, to exit from Error code display mode.
6.2. Confirmation of Firmware Version The Firmware version can be confirmed by ordering the following steps:. • Step 1. The temporary cancellation of factory setting: Set the mode dial to “[ Normal picture mode ] (Red camera mark)”. Insert the SD memory card which has a few photo data. While keep pressing [ Optical Image Stabilizer ] and “[ UP ] of Cross key”...
7.2. When Replacing the Main PCB After replacing the MAIN PCB, be sure to achieve adjustment. The adjustment instruction is available at “software download” on the “Support Information from NWBG/VDBG-PAVC” web-site in “TSN system”, together with Maintenance software. 7.3. Service Position This Service Position is used for checking and replacing parts.
8.3. Disassembly Procedure Item Rear Case Unit Fig. D1 Fig. D2 LCD Unit Fig. D3 Front Case Unit Fig. D4 Main P.C.B. Fig. D5 Fig. D6 Top Operation Unit Fig. D7 Jack P.C.B. Fig. D8 Power/Top P.C.B. Fig. D9 Fig. D10 Fig.
Page 22
8.3.2. Removal of the LCD Unit Fig. D2 Fig. D3...
Page 23
8.3.3. Removal of the Front Case Unit 8.3.4. Removal of the Main P.C.B. Fig. D5 Fig. D4 Fig. D6...
Page 24
8.3.5. Removal of the Top Operation Unit Fig. D7 8.3.6. Removal of the Jack P.C.B. Fig. D8 8.3.7. Removal of the Power/Top P.C.B. Fig. D9...
Page 25
Fig. D11 8.3.8. Removal of the Lens Unit Fig. D10 Fig. D12...
Page 26
8.3.10. Removal of the Battery Door Unit and Battery Case Unit Fig. D13 8.3.9. Removal of the SD/AFE P.C.B. Fig. D15 Fig. D14...
8.3.11. Removal of the Battery Case Fig. D16 NOTE: (When Assembling) Be sure to confirm the following points when assembling. • The Screw is tightened enough. • Assembling conditions are fine. (No distortion, no illegal- space.) • No dust and/or dirt on every Lens surfaces. •...
Page 28
8.4.1. Removal of the 1st Lens Frame/ Drive Frame/Fixed Frame Unit 1. Unscrew the 2 screws (A). 2. Depress the zoom motor unit to relese the locking tabs (2 pcs), and then remove to the indicated by arrow. 3. Unscrew the 2 screws (B). 4.
8.5. Assembly Procedure for the Lens 8.5.1. Phase alignment of the Drive Frame Unit and Fixed Frame Unit 8.5.2. Phase alignment of the 1st Lens Frame Unit and Drive Frame/Fixed Frame Unit 8.5.3. Phase alignment of the 1st Lens Frame/Drive Frame/Fixed Frame Unit and Lens Base Unit...
9 Measurements and Adjustments 9.1. Matrix Chart for Replaced Part and Necessary Adjustment The relation between Replaced part and Necessary Adjustment is shown in the following table. When concerned part is replaced, be sure to achieve the necessary adjustment(s). As for Adjustment condition/procedure, consult the “Adjustment Manual” which is available in Adjustment software. The Adjustment software is available at “TSN Website”, therefore, access to “TSN Website”...
10 Maintenace 10.1. Cleaning Lens and LCD Panel Do not touch the surface of lens and LCD Panel with your hand. When cleaning the lens, use air-Blower to blow off the dust. When cleaning the LCD Panel, dampen the lens cleaning paper with lens cleaner, and the gently wipe the their surface. Note: The Lens Cleaning KIT ;...
Page 33
Service Manual Diagrams and Replacement Parts List Digital Camera DMC-TZ1PP DMC-TZ1EG DMC-TZ1GT DMC-TZ1PL DMC-TZ1EGM DMC-TZ1SG DMC-TZ1EB DMC-TZ1GC DMC-TZ1EE DMC-TZ1GK DMC-TZ1EF DMC-TZ1GN Vol. 1 Colour (S)...Silver Type (K)...Black Type (A)...Blue Type (Except PL/GN/GT) Table of contents S1. About Indication of The Schematic Diagram ... S-1 S1.1.
Note) Indicated voltage values are the standard values for the unit measured by the DC electronic circuit tester (high-impedance) with the chassis taken as standard. Therefore, there may exist some errors in the voltage values, depending on the internal impedance of the DC circuit tester. S2.1.
S3.1. Overall Block Diagram (35mm ~ 350mm) IC3101 1/2.5" 6.37 MEGA PIX EFFECTIVE: 5M ZOOM IRIS SHUTTER OIS UNIT FOCUS IC7002 LINEAR AF DRIVE IC7001 MOTOR DRIVE, OIS DRIVE& PRE PROCESS IC7101 IC7003 GYRO SHUTTER SENSOR X/Y DRIVE FLASH REAR OPERATION UNIT IC9101 SYSTEM IC (32.768kHz)
S4.1. Interconnection Diagram PS9901 POWER / TOP P.C.B. (FOIL SIDE) JACK P.C.B. (COMPONENT SIDE) PP2001 USB(+) USB(-) VIDEO GND USB GND SELF LED A VIDEO OUT SELF LED K 5 USB CABLE IN UNREG GND CABLE DET UNREG GND LINE OUT UNREG GND UNREG+ UNREG GND...
S4.2. Power (P) Schematic Diagram CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE 1.5A 32V FUSE. ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQUES 1.5A 32V D' INCENDIE N' UTILISERQUE DES FUSIBLE DE MÉME TYPE 1.5A 32V. 1.5A 32V 1.5A 32V S-10...
Page 43
S-11 S-11 DMC-TZ1 Power Section (Power Top P.C.B. (1/4)) Schematic Diagram (P)
S4.4. Flash (ST) Schematic Diagram CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE 1.25A 32V FUSE. ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQUES 1.25A 32V D' INCENDIE N' UTILISERQUE DES FUSIBLE DE MÉME TYPE 1.25A 32V. S-15 1.25A 32V DMC-TZ1...
S4.6. Jack Schematic Diagram 1.5A 32V CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE 1.5A 32V FUSE. ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQUES 1.5A 32V D' INCENDIE N' UTILISERQUE DES FUSIBLE DE MÉME TYPE 1.5A 32V. S-17 DMC-TZ1 Jack...
S4.8. Lens Flex Schematic Diagram D GND MR VCC FM P FM N X VH+ X VO- X VH- Y VH- Y DR+ Y DR- X VO+ X DR- X DR+ Y VH+ Y VO- TO MAIN (MAIN CN) CIRCUIT Y VO+ (FP9004) SHUT2...
S6. Replacement Parts List Note: 1.* Be sure to make your orders of replacement parts according to this list. 2. IMPORTANT SAFETY NOTICE Components identified with the mark When replacing any of these components, use only the same type. 3. Unless otherwise specified, All resistors are in OHMS, K=1,000 OHMS.
Page 58
DMC-TZ1PP/PL/EG/EGM/EF/EB/EE/GC/SG/GT/GK/GN/GD vol.1 Ref.No. Part No. Part Name & Description ------ P.C.B. LIST ------ VEP56033A MAIN P.C.B. VEP51005A POWER/TOP P.C.B. VEP53030A SD/AFE P.C.B. VEP59026A JACK P.C.B. VXW0797 CAMERA LENS UNIT --- INDIVIDUAL PARTS --- C8003 F2A2F8500002 E.CAPACITOR ET8001 VSQ1235 EARTH SPRING JK9901 K4ZZ03000324 BATTERY CATCHER...
Page 60
DMC-TZ1PP/PL/EG/EGM/EF/EB/EE/GC/SG/GT/GK/GN/GD vol.1 Ref.No. Part No. Part Name & Description -- CASING/LENS SECTION -- VKM6892KIT REAR CASE UNIT VKM6894KIT REAR CASE UNIT VKM6920KIT REAR CASE UNIT VGK3216 STRAP ORNAMENT VGK3224 STRAP ORNAMENT VYK1V41 FRONT CASE UNIT VYK1V44 FRONT CASE UNIT VYK1V42 FRONT CASE UNIT VEP53030A SD/AFE P.C.B.
Page 61
DMC-TZ1PP/PL/EG/EGM/EF/EB/EE/GC/SG/GT/GK/GN/GD vol.1 Ref.No. Part No. Part Name & Description ---- PACKING SECTION ---- VYF3082 LENS CAP U 304 DE-A25BA BATTERY CHARGER 304 DE-A26AA BATTERY CHARGER 304 DE-A26BA BATTERY CHARGER 304 DE-A26CA BATTERY CHARGER K1HA08CD0007 USB CABLE K1HA08CD0008 AV CABLE VFC4090 HAND STRAP...