Related Manuals for Gree FLR09HP230V1AF
Summary of Contents for Gree FLR09HP230V1AF
- Page 1 UNIVERSAL FLOOR/CEILING OWNER’S MANUAL Models: FLR09HP230V1AF FLR12HP230V1AF FLR18HP230V1AF FLR24HP230V1AF...
-
Page 2: Table Of Contents
Air Conditioning & Heating System! You can feel confident in your selection because the same pride in craftsmanship and engineering knowledge that goes into millions of other Gree installed products worldwide has gone into your unit. Please read this owner’s manual carefully before operation and retain it for future reference. -
Page 3: Introduction
4-way air discharge, multi speed fan, swing louver and a cleanable air filter. Gree’s cutting edge fan technology is quiet and powerful. It efficiently circulates the conditioned air throughout the space while safely removing water via the internal condensate drain pump. -
Page 4: Safety Precautions
• Disconnect electrical power to the indoor and outdoor units before performing any maintenance or cleaning. • Do not attempt to repair the Gree system yourself. Incorrect repairs may cause electric shock or fire. Contact a qualified service technician for all service requirements. -
Page 5: System Parts
SYSTEM PARTS Air Outlet Indoor Unit Air inlet Power Supply Part Name 1. Front Cabinet 2. Air Inlet 3. XK-19 Wired Controller (Optional) 4. Remote Controller 5. Drain Pipe 6. Gas Pipe 7. Liquid Pipe 8. Service Cover 9. Front Panel Air inlet Outdoor Unit Air outlet... -
Page 6: System Functions
LCD display. TETHER CONTROLLER The Gree wired Tether Controller mounts to the wall up to 26 feet from the unit. It provides complete control over your unit’s operation mode, desired temperature,... - Page 7 SYSTEM FUNCTIONS INTELLIGENT DEFROST The Intelligent Defrost function increases room comfort and saves energy by eliminating unnecessary defrost cycles. In heating mode, the unit will monitor the outdoor coil for frost buildup. Once frost buildup has been detected, the system will switch into a defrost mode to remove the frost.
- Page 8 The remote controller can be set to display in either °F or °C. SELF-DIAGNOSIS With an on-board computer using real-time diagnostics, the Gree Multi21 system helps to prolong its own life. The automatic diagnosis feature continuously scans for unacceptable operating conditions or malfunctions. If such conditions occur, the system takes corrective action or stops.
- Page 9 OPERATION OF WIRELESS REMOTE CONTROLLER Remote Controller Part Name 1. ON/OFF Button 2. Down Button 3. Up Button 4. Fan Button 5. Mode Button 6. I Feel Button 7. Clock Button 8. Timer On Button 9. Swing Louver Button 10. X-Fan Button 11.
-
Page 10: Operation Of Wireless Remote Controller
OPERATION OF WIRELESS REMOTE CONTROLLER REMOTE CONTROLLER OPERATIONS The wireless remote controller is sleek, versatile and allows you to change room temperatures and functions on your Multi21 Floor/Ceiling system from the palm of your hand. The large LCD display and buttons make it easy-to-understand and easy-to-use. The remote controller is set from factory to display temperatures in °F. - Page 11 OPERATION OF WIRELESS REMOTE CONTROLLER MODE BUTTON : AUTO Use the “MODE” button to select one of the available modes. : COOL The selected mode will be displayed on the remote controller and : DRY the appropriate light will illuminate on the front display panel. : FAN ONLY AUTO –...
- Page 12 OPERATION OF WIRELESS REMOTE CONTROLLER TIMER SETTING Timer-ON / Timer-OFF BUTTON To set when you want the unit to turn On at the end of a selected time period, use the button labeled “Timer-ON /Timer-OFF”on the remote controller. Press this button to make the clock icon disappear, replaced with the word “ON”...
- Page 13 OPERATION OF WIRELESS REMOTE CONTROLLER FAN BUTTON Press the FAN button to adjust the indoor fan speed: Low ( ), Medium ( ), High ( ), Turbo and Auto. • Turbo function is not available in Dry and Auto mode. •...
- Page 14 OPERATION OF WIRELESS REMOTE CONTROLLER SLEEP MODE The Multi21 Floor/Ceiling system will automatically adjust room temperature during your sleep time. This slight change in temperature will not affect your comfort level due to the natural effects that sleeping has on the body, but it will save on energy consumption and will lower your electric bill.
-
Page 15: Wired Tether Controller
OPERATION OF WIRED TETHER CONTROLLER ON/OFF BUTTON Press On/Off to turn On the unit. Press again to turn it Off. “Off” State “On” State MODE SETTING When the unit is ON, press Mode button to select an operating mode. It will change sequentially as shown below: Auto–Cool–Dry–Fan–Heat Cool Heat... -
Page 16: Turbo Setting
OPERATION OF WIRED TETHER CONTROLLER FAN SETTING When the unit is ON, press Fan button to select the fan speed of the indoor unit. It will change sequentially as shown below. Medium High TURBO MODE Turbo mode will force the unit up to maximum capacity to heat or cool the room in the shortest amount of time. - Page 17 OPERATION OF WIRED TETHER CONTROLLER TIMER SETTING The Multi21 System has two timer modes. The Timer-On mode will turn the unit ON after the preset time period. The Timer-Off Mode will turn the unit OFF after the preset time period. The preset time period can be from 0.5 to 24 hours in 0.5 hour increments.
- Page 18 OPERATION OF WIRED TETHER CONTROLLER Timer-Off Setting Set the time period for the unit to remain ON before turning OFF by pressing the ▲ or ▼ Turn the unit On, press the Timer button. The ON icon will flash and the hours will be displayed. buttons.
- Page 19 OPERATION OF WIRED TETHER CONTROLLER SLEEP MODE The unit will automatically adjust room temperature during your sleep time. This slight change in temperature will not affect your comfort level due to the natural effects that sleeping has on the body, but it will save on energy consumption and will lower your electric bill. Press the SLEEP button to select Sleep Mode.
- Page 20 OPERATION OF WIRED TETHER CONTROLLER X-FAN MODE The X-Fan function may only be selected in Cool and Dry modes. After the unit is turned Off, the X-Fan function will keep the indoor fan running for 2 minutes to dry the indoor evaporator coil to help avoid mold and mildew growth.
- Page 21 OPERATION OF WIRED TETHER CONTROLLER I-FEEL MODE The indoor unit will sense room temperature at the wired Tether Controller instead of at the return air section of the indoor unit. Indoor Unit Room Sensor A Tether Controller Indoor Room Sensor B I-Feel Settings Press the Function button until the I-Feel icon is displayed, then press Enter/Cancel to activate the function.
- Page 22 OPERATION OF WIRED TETHER CONTROLLER CELSIUS OR FAHRENHEIT TEMPERATURE DISPLAY The wired Tether Controller is set from the factory to display ▼ temperature in Fahrenheit ( Fº). If Celsius (Cº) is desired, turn the unit OFF, press Mode and buttons at the same time for 5 seconds to alternate between temperature displays.
-
Page 23: Care And Cleaning
CARE AND CLEANING Routine maintenance consists of checking the condensate drain for clogs, hosing off the outdoor coil of outdoor unit and cleaning the air filter and the indoor cabinet. W RNING Turn off power and disconnect from indoor and outdoor units before cleaning. Failure to do so could cause electric shock. -
Page 24: Troubleshooting
TROUBLESHOOTING PROBLEM CAUSE/SOLUTION System does not restart. Cause: The system has a built-in three-minute delay to prevent short and/or rapid cycling of the compressor. Solution: Wait three minutes for the protection delay to expire. Indoor unit emits unpleasant odor Cause: Typically unpleasant odors are the result of mold or mildew forming on when started the coil surfaces or the air filter. -
Page 25: Troubleshooting
TROUBLESHOOTING PROBLEM CAUSE/SOLUTION Water leaking from the indoor Cause: While it is normal for the system to generate condensate water in unit into the room. cooling mode, it is designed to drain this water via a condensate drain system to a safe location. Solution: If water is leaking into the room, it may indicate one of the following. -
Page 26: Diagnostic Codes
DIAGNOSTIC CODES Troubleshooting The unit has onboard diagnostics. The outdoor unit will provide status indicators. The indoor wall unit and remote controller will display error codes. The following is a summary of the codes with explanation: Indoor Unit Outdoor Unit Indicators Malfunction Name Possible Causes &... - Page 27 DIAGNOSTIC CODES Outdoor Unit Indicators Indoor Unit Malfunction Name Possible Causes Display Yellow High Temperature 6 flashes 1) Incorrect refrigerant charge level Resistant Protection and 1 sec Off 2) Refrigerant metering device malfunction 3) Compressor malfunction Cold Air Protection 1) Indoor coil has not reach minimum heating temperature 2) Indoor ambient is abnormally cold 3) Indoor control board malfunction EEPROM Memory Malfunction...
- Page 28 DIAGNOSTIC CODES Outdoor Unit Indicators Indoor Unit Malfunction Name Possible Causes Display Yellow High Compressor Discharge 2 flashes and 4 flashes 1) Cooling load is too great Temperature - Frequency 1 sec Off and 1 sec Off 2) Outdoor ambient temperature too high Decrease/Limit Mode 3) Refrigerant charge too low 4) Metering device malfunction...
-
Page 29: Diagnostic Codes
DIAGNOSTIC CODES Outdoor Unit Indicators Indoor Unit Malfunction Name Possible Causes Display Yellow Incompatible Indoor and 16 flashes Indoor and outdoor units are not compatible Outdoor Units and 1 sec Off Compressor Phase Current 1) IPM module malfunction Protection 2) Outdoor control board malfunction 3) Compressor malfunction Module Temperature Sensor Outdoor control board malfunction... -
Page 30: Energy Saving Tips
ENERGY SAVING TIPS 1. Relaxing room temperature at night is OK: During the nighttime hours you don't require the same level of conscious cooling or heating. Try using Sleep Mode to gradually relax room temperature and allow the unit to run less and save energy. 2. -
Page 31: Limited Warranty
LIMITED WARRANTY GREE distributor (hereinafter “Company”) warrants this product against failure due to defect in materials or workmanship under normal use and maintenance as follows. All warranty periods begin on the date of original installation. If the date cannot be verified, the warranty period begins one hundred twenty (120) days from date of manufacture.