Advertisement
Safety Instructions
The TV set can be operated on AC AUTO 110-240V, 50/60Hz (TC-21FX20M,
TC-21FX20R, TC-29FX20M, TC-29FX20R, TC-29FX20U, TX-21FX50M, TX-29FX50M),
or AC SINGLE 230-240V, 50Hz (TX-21FX50A, TX-29FX50A), or AC SINGLE 220V, 50Hz
(TC-29FX50H), or AC SINGLE 220-240V, 50/60Hz (TX-21FX20R, TX-29FX20R).
The apparatus shall not be exposed to dripping or splashing and that no objects fi lled with
liquids, such as vases, shall be placed on the apparatus.
Do not remove the rear cover, as live parts are accessible when it is removed.
Remove the plug from the wall outlet (Power point) when the TV set is not used for a
prolonged period of time. The main plug is used as the disconnecting device.
Getting Started
L Connections
Connecting the aerial
VHF Aerial
UHF Aerial
Mixer
75 Ω Coaxial
Coaxial
Cable
Aerial Plug
Connecting to
the AV2 Input
Audio
Video
R
OUT
L
Terminals
Notes
• When a Monaural VCR is used, connect the Monaural Audio cable to the Audio Out "L" (left) terminal.
• The AV3 audio input terminals serves as the audio input terminal for both the video input and for the DVD input.
• The DVD signal input terminal takes priority over the AV3 video signal input terminals.
• Never connect the same video recorder with both the VIDEO IN and MONITOR OUT terminals on this TV set, as this could cause
incorrect operation.
• The DVD signal (Y·P
·P
) is not output at the MONITOR OUT terminals.
B
R
L Installing the remote control's batteries
Open
1
Insert the R6 (AA) size batteries.
2
Tuning menu
1
2
Access the Main menu.
Select Setup menu.
Tuning menu
OK
Sys select
(System
select)
Auto tuning
Manual tuning
Applicable for Teletext
models only.
TC_TX-21_29FX20_50_EN.indd 3
TC_TX-21_29FX20_50_EN.indd 3
AV1
MONITOR
A V 3 I N
IN
COMPONENT
OUT
Y
VIDEO
MONO
MONO
P
B
L
AUDIO
P
R
R
RF in Terminal
OUT
VHS VCR
V I D E O
L / M O N O
R
A V 2
I N
A U D I O
3
3
4
Access Setup menu.
Choose Tuning menu.
Description
Select the system.
China
HK/UK
Asia/M.East
NZ/INDONES
Japan
CATV
America
SPECL Ver
E.Europe
Note
You need to set the "Sys select" mode before carrying out
Auto and Manual tuning.
Allows you to automatically retune the TV. Useful if you
move house and wish to retune your TV to the local
stations.
1. Press the Volume "–" or "+" button to start Auto tuning.
2. Once this operation is completed, the TV will display the
programmes now stored on programme position 1.
Allows individual programme positions to be tuned manually.
1. Press the Volume "–" or "+" button to start Manual tuning.
2. Press the Programme Number "3" or "4", Direct key
0~9 or – – (2 digit key) button to select the programme
position to be tuned.
3. Press the Volume "–" or "+" button repeatedly until the
required station is found.
4. Repeat the above steps to tune other programme
positions.
The cabinet and picture tube can be kept in good condition by simply wiping with a clean,
soft cloth moistened with mild detergent and water. Do not use solutions containing benzol,
petroleum or a chemical cloth. For safety, remove the plug from the wall outlet.
Adequate ventilation is essential to prevent failure of electrical components, so we
recommend a gap of at least 10 cm (
cabinet or between shelves.
Avoid exposing the TV set to direct sunlight and other source of heat.
Do not use this set if abnormal operation occurs.
Ex: smoke, odd sounds or smells, turn the power switch off and disconnect the AC power if
you notice any unusual operation.
Do not put the AC cord underneath your TV set or any other object.
Connecting
to the AV1
or AV3 Input
Terminals
Connecting
to the
DVD Input
Terminals
(TV front panel)
Connecting
Other Equipment
Headphone
to the AV Monitor
Output Terminals
Close
Cautions
• Do not use rechargeable (Ni-Cd) batteries. They are different in shape and performance and may fail to ensure correct
operation.
• Incorrect use of batteries can cause electrolyte leakage which will corrode the remote control or cause the batteries to
burst.
5
6
Access Tuning option.
Choose menu option.
Australia
) is left all around the unit when it is placed inside a
VHS VCR
Audio
Video
Yellow
R
OUT
L
OUT
White
DVD player
R
L
P
P
Y
R
B
Recording equipment (VHS VCR)
Audio
Video
R
IN
L
IN
7
8
Adjust/access chosen
Exit the menu
menu.
(press twice).
Tuning menu
Description
Sound system
You can change the Sound system used for a programme
channel.
4.5 MHz
6.5 MHz
Colour system
Lets you select the correct transmission standard.
Auto
PAL
NTSC 3.58
Fine tuning
Use to make small adjustments to the tuning of an individual
station.
Skip
To skip the undesired Programme Numbers from appearing
on the screen.
This function is only effective when selecting Programme
Numbers by pressing the Programme Number "3" or "4"
button. Skip mode can be switched on or off.
Ch Colour set
Variation in colour density between broadcast channels can
be adjusted to three levels of each reception channel.
Note:
The set is pre-tuned for Australian Ch's 2, 7, 9, 10, 28, 31 and Auto tuning is NOT
required.
Red
White
Red
Yellow
White
Red
Return to normal TV
screen.
5.5 MHz
6.0 MHz
SECAM
NTSC 4.43
2/16/06 10:22:27 AM
2/16/06 10:22:27 AM
Advertisement
