Page 1
AUTOMATIC PARTS WASHER SC-2412A SC-2412D For technical assistance or the SHARK dealer nearest you, call 1-800-771-1881 or visit our website at www.shark-pw.com 97-6267...
Power Brush (Deluxe Edition only) Detail Brush and Flow Regulator (Deluxe Edition only) Dual Oil Separator (DOS) System Low Water Shut-off System Automatic Water Fill Detergents and Additives Detergent Rust Inhibitor Additive Preparing the Machine for Use SHARK SC-2412 • 97-6267 • REV. 3/04...
Page 4
The model and serial numbers will be found on a decal attached to the parts washer. You should record both serial number and date of purchase and keep in a safe place for future reference. SHARK SC-2412 • 97-6267 • REV. 3/04...
Before you begin to install and use the ma- trical power indicated on the electrical specifications chine, please familiarize yourself with the major com- tag. Operating the machine on any other power sup- ponents. ply will permanently damage the motors. SHARK SC-2412 • 97-6267 • REV. 3/04...
Lid Handle Optional Air Flow Lid Support Strut Valve w/Flow Regulator Optional Detail Brush Pump Low Water Shut-Off System Power Cord DOS System™ w/ Optional Automatic Optional Oil Water Fill Assembly Collection Container SHARK SC-2412 • 97-6267 • REV. 3/04...
Step 1: Hose Connection Remove the power brush from the box, install the wire brush in the chuck, and connect the air hose. SHARK SC-2412 • 97-6267 • REV. 3/04...
If your machine is not equipped with optional automatic water fill feature, add water through the wash chamber until the low water shut-off system indicates that the sump is full. The sump capacity is 25 gallons. SHARK SC-2412 • 97-6267 • REV. 3/04...
(120V only). After long wash cycles it may be necessary to let the machine sit idle for a period of time to allow the wash solution to reheat to operating tem- perature. SHARK SC-2412 • 97-6267 • REV. 3/04...
It is a three-way ball valve that controls the flow of compressed air to the power brush and the hand detail brush (See Figure Below). Detail Brush Air In Turntable Thrust Bearing Power Brush Detail Brush Pump Power Brush SHARK SC-2412 • 97-6267 • REV. 3/04...
Top switch CLOSED, Bottom Switch Water Fill Valve (if installed) CLOSED, CLOSED, Automatic Water Fill Valve (if OPEN, Automatic Water Fill Valve (if Heating Element ON. installed) OPEN, Heating Element OFF. installed) OPEN, Heating Element OFF. SHARK SC-2412 • 97-6267 • REV. 3/04...
Make sure none of the parts extend beyond the edge of the turntable and make sure large, light parts (valve covers, for example) are secured to the turntable. SHARK SC-2412 • 97-6267 • REV. 3/04...
Step 6: Allow the thermostat to cool to room temperature, then test for continuity. If there is not continuity the thermostat is no longer functional; replace the thermostat. Screws SHARK SC-2412 • 97-6267 • REV. 3/04...
Heat the wash water to operating temperature, then add the solution either use the sump drain or a small sub- appropriate amount of factory detergent. mersible pump. Step 8: Run the machine through a 15-minute wash cycle. SHARK SC-2412 • 97-6267 • REV. 3/04...
Required Tools and Equipment • 5/16" wrench or socket • 1/2" wrench or deep socket • small phillips-head screwdriver • small flat-head screwdriver Replacement Procedure Step 1: Disconnect power to the machine. Heating Element SHARK SC-2412 • 97-6267 • REV. 3/04...
To adjust the torque limiter, perform the following pro- panel beneath the lid cover. To replace the turntable cedure; motor, perform the following procedure: Step 1: Step 1: Raise the lid. Disconnect power to the machine. SHARK SC-2412 • 97-6267 • REV. 3/04...
Page 23
Loosen the retaining screw to remove the torque arm assembly from the drive shaft (use a 1/8" allen wrench – See Figure Below). Retaining Screw Adjusting Bolt Step 6: Remove the three turntable mounting screws (See Fig- ure Above). SHARK SC-2412 • 97-6267 • REV. 3/04...
Page 25
TICULAR PURPOSE. SHARK does not authorize any other party, including authorized Dealers, to make any representation or promise on behalf of SHARK, or to modify the terms, conditions, or limitations in any way. It is the buyer’s responsibility to ensure that the installation and use of SHARK products conforms to local codes.
Page 26
Form #97-6267 • Revised 3/04 • Printed in U.S.A.