Configuring The Ilmi Management Ip Address; Displaying Neighbors - Cisco BPX 8620 Installation And Configuration Manual

Chapter 19 Configuring Circuit Lines and Ports

Configuring the ILMI Management IP address

The Management IP address is used by the NMS application to access the BPX or the ATM device.
Depending on your network set up, you can configure the BPX to send either the LAN IP address or
Network IP address as part of the neighbor information exchange with the attached ATM device.
To configure the ILMI management IP address, use the following procedure.
Enter the cnfnodeparm command with option #56 Dnld LanIP or NwIP to select LAN IP or NETW IP
Step 1
as follows:
This Command: cnfnodeparm <
Select option 56 as the parameter index.
Step 2 Enter 0 for LAN IP address or 1 for Network IP address. The default is the network IP address for BPX.
The following is an example of the cnfnodeparm screen:
sw143
31 TFTP Write Retries
32 SNMP Event logging
33 Job Lock Timeout
34 Max Via LCONs
35 Max Blind Segment Size [ 3570] (D)
36 Max XmtMemBlks per NIB [ 3000] (D)
37 Max Mem on Stby Q (%)
38 Stat Config Proc Cnt
39 Stat Config Proc Delay [ 2000] (D)
40 Enable Degraded Mode
41 Trk Cell Rtng Restrict [
42 Enable Feeder Alert
43 Reroute on Comm Fail
44 Auto Switch on Degrade [
45 Max Degraded Aborts
This Command: cnfnodeparm 56
Enter 0 (LanIP) or 1 (NwIP):

Displaying Neighbors

To display the neighbors, use the following procedure.
Step 1 Enter the dspnebdisc command to display all the neighbor's information discovered by the BPX through
the procedure in the ILMI Neighbor Discovery section:
Last Command: dspnebdisc <
Enter the applicable slot number.
Step 2
The following is an example of the Port Neighbor Discovery screen:
sw143
Port Neighbor Discovery
Release 9.3.30, Part Number 78-12907-01 Rev. E0, May 2005
parameterIndex
TN Cisco BPX 8620
[ 3] (D)
[ Y] (Y/N) 47 Htls Counter Reset Time[1000] (D)
[ 60] (D)
[50000] (D)
[ 33] (D)
[ 1000] (D)
[ Y] (Y/N) 55 LCN reprgrm batch cnt
Y] (Y/N) 56 Dnld LanIP or NwIP
[ N] (Y/N)
[ N] (Y/N)
Y] (Y/N)
[ 100] (D)
slot number
>
TN Cisco BPX 8620
>
9.3.10 Aug. 9 2000
46 Max Htls Rebuild Count [ 100] (D)
48 Send Abit early
49 Abit Tmr Multiplier
50 Abit Tmr Granularity N [
51 FBTC with PPDPolicing
52 CommBrk Hop Weight
53 CB Fail Penalty Hops
54 Auto BXM upgrade
9.3.10 Aug. 9 2000 17:02 GMT
Cisco BPX 8600 Series Installation and Configuration
ILMI Neighbor Discovery
16:25 GMT
[ N] (Y/N)
M [ 0] (D)
3] (D)
[ N] (Y/N)
[ 25] (D)
[ 2] (D)
[ Y] (Y/N)
[ 100] (D)
[ 1](Lan/Nw)
19-11