Page 27
COM port Outlets Hot-Swap Redundant Power Supply Housing Fan Expansion Slots SCSI Expansion Slots (Optional) ...
Page 28
Hot-swap Redundant Power Supply Housing Fan Expansion Card 5.25-inch Drive Bays Slots 3.5-inch Drive Bay Back-plane Board Power Switch Power LED Hot-Swap Cage Hard Disk Drive LED (SCSI) System Status LED (reserved) Removable Hard Disk Drive Trays <...
Page 48
The power supply subsystem should supply a minimum of 337-Watts to the whole system. If you only have one power supply or if you have two power supplies and are planning to remove both of them, remember to turn off the power first and disconnect the power cord from the electrical outlet.
Page 63
& & &
"7 !)
$#
!
" 2
#Electrostatic discharge (ESD) can damage your processor, disk drives, expansion boards, and other components. Always observe the following precautions before you install a system component. 1.Do not remove a component from its protective packaging until you are ready to install it.
Page 64
#. ??+
?
?'
60 =
?+
'
'#34
?
# G
?+
&
?
'
?$
?'
# ?
2
#If you do not match the CPU socket Pin 1 and CPU cut edge well, it may damage the CPU. ?'
...
Page 65
#.<"!
# ?
?#"
,0'
#"
7%& '
@!! 3 ?,-0
2
#Some CPU fans do not have sense pin, so that cannot support fan monitoring. :$@!! ...
Page 67
=#.
>*$4
!'%#.*6 9
! ? $
-N,.-N,.? )
%9+ $
?
#!
6F 7
%9+
?$'
#2 (( 71# We strongly recommend you do not overclocking your CPU and system for get more system reliability. ...
Page 70
//( & !
"
+150-GG'
$
?+?+,, !!
A3+A$ %AP+,,GBE4& -N,.
%-
G"
DG
-
G *# The driving capability of new generation chipset is limited due to the lack of a memory buffer (to improve performance). This makes DRAM chip count an important factor to take into consideration when you install DIMMs.
Page 71
-GG" ")
1."
.'9
!! .0'%-
G#
"
*# To identify 2-clock and 4-clock DIMM, you may check if there are traces connected to the golden finger pins 79 and 163 of the SDRAM. If there are traces, the SDRAM is probably 4-clock; Otherwise, it is 2-clock. *# To identify single-side or double-side DIMM, check golden finger pin 114 and pin 129.
Page 75
->+'$
! ->
>
$->
!'
##
$'
)
$ !
"
##
)!>
"
'
-@G&
!
!
7 ! -> )#
'-@G! 71# The specification of the IDE cable is a maximum of 46cm (18 inches), make sure your cable does not exceed this length. *# For better signal quality, it is recommended to set the far end side device to master mode and follow the suggested sequence to install your new device.
Page 133
&$& $!
#
Be very careful when typing your password because the actual characters do not appear on the screen. ?
>*&>'0
$
# #
>*&>' B
H !.&(*I
>*&>' ?
>%'
%
!%
?
>%'
(
& >(
%
$ HII
(
%
F $$"
G@% # $
!
$)
H%6*I
"
#
9
.$& (* &
!
!
E *3-#
4 @
$)
$ ?
...
Page 146
& & !
%%%
O
#
A@% ?@%&
&
) Q
$
#$! $0
!
8 ?V
UV
U#%%Select
; Your screen may show the key sequence as + <Hot Key> instead of + A. The correct sequence is + A. ...
Page 147
& & 9
%%%
0566%%
!)
#$@
! 8
0566%%%
3&G4
+ F
0566 A 8-8 %%
! G
" 88 # 868
"# V>
U 868A VU0&! ! $'
! )V>
U
)V>U
(
3TP#
4 ;...
4.2.1 Configuring Channel A & #$#
8 If you choose to configure Channel B, a similar SCSI Utility Screen will appear. The only difference is the I/O Port Address: A000h for Channel A A400h for Channel B <...
Page 163
0566%%%
3&G4
+ %%-#
%%-- W W+ W W, W. W W1 W 000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 %&#
3GA%4+1 +1 +1 +1 +1 +1 +1 +1
9*
CCCF F F F F F F F...
See the section Disk Drives Over 1 GB” in this chapter, for more information on this option. This option should be left disabled for most operating systems except DOS. 4.4.4 Support Removable Disks Under BIOS as Fixed Disks &
$
$ !"0!
"
%%
A@%& $
%%
A@%"& #
/:& #$ "8 •...
!
If a removable-media SCSI device is controlled by the SCSI controller BIOS, do not remove the media while the drive is powered-on or you may lose data! 4.4.5 BIOS Support for Bootable CD-ROM 9 ")
$
"
"-0@G
!& #
6* 4.4.6 BIOS Support for Int13 Extensions &
$
%%
A@%
+,#
& #
6*...
!"
$
)
0 ! $
#
)
4.5.1 Format Disk & !
-'
#!$0#!
' G
%%'#!
"#!
&
!
-'
!
"$
!7
#%%'
' !"0!
$ $
0
%%
A low-level format destroys all data on the drive. Be sure to back up your data before performing this operation.
Page 177
If you have already partitioned a large hard disk drive with one translation method, conversion to another method erases the data on the drive. Be sure to back up your disk drive prior to any change in the translation method. ;;...