Related Manuals for Black Box 40418
Summary of Contents for Black Box 40418
- Page 1 © Copyright 2008. Black Box Corporation. All rights reserved. 1000 Park Drive • Lawrence, PA 15055-1018 • 724-746-5500 • Fax 724-746-0746...
- Page 2 Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500) SUPPORT FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746 INFORMATION Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018 Web site: www.blackbox.com • E-mail: info@blackbox.com...
- Page 4 FCC INFORMATION FEDERAL COMMUNICATIONS COMMISSION INDUSTRY CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS This equipment generates, uses, and can radiate radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio communication. It has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in Subpart B of Part 15 of FCC rules, which are designed to provide reasonable protection against such interference when the equipment is...
- Page 5 MODEM ROUTER SWITCH FCC REQUIREMENTS FOR TELEPHONE-LINE EQUIPMENT 1. The Federal Communications Commission (FCC) has established rules which permit this device to be directly connected to the telephone network with standardized jacks. This equipment should not be used on party lines or coin lines.
- Page 6 Repairs to certified equipment should be made by an authorized maintenance facility—in this case, Black Box. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.
- Page 7 MODEM ROUTER SWITCH NORMAS OFICIALES MEXICANAS (NOM) ELECTRICAL SAFETY STATEMENT INSTRUCCIONES DE SEGURIDAD 1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado. 2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura.
- Page 8 NOM STATEMENT 12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del equipo no sea eliminada. 13. Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados sobre o contra ellos, poniendo particular atención a los contactos y receptáculos donde salen del aparato.
- Page 9 MODEM ROUTER SWITCH TRADEMARKS USED IN THIS MANUAL BLACK BOX and the Double Diamond logo are registered trademarks of BB Technologies, Inc. Any other trademarks mentioned in this manual are acknowledged to be the property of the trademark owners.
-
Page 10: Table Of Contents
A.1 Calling Black Box ........ -
Page 11: Specifications
40419: (1) Verify Connection Power: 115 VAC, 60 Hz Size: 40418: 0.8"H x 7.5"W x 4.3"D (2 x 19.1 x 10.9 cm); 40419: 0.8"H x 1.5"W x 3"D (2 x 3.8 x 7.6 cm) Weight: 40418: 1 lb. (0.5 kg);... -
Page 12: Overview
CHAPTER 2: Overview 2. Overview 2.1 Introduction With the Modem Router Switch, you can switch inbound modem calls to any of eight receiving modems (PCs, servers, etc.) that the caller selects. Designed primarily for modem applications, you can also use it for voice, fax, or other analog switching applications. -
Page 13: Security Key (Part Number 40419)
MODEM ROUTER SWITCH 2.1.3 S 40419) ECURITY UMBER You can program the Security Key through the RJ-11 “Program Ports.” NOTE Each Security Key may be programmed differently, allowing only various units to access selected ports. Each Modem Router Switch transfers a unique factory system ID code and a user- selected ID to the Security Key during programming. -
Page 14: Components
2.2 Components 2.2.1 F RONT ANEL Figure 2-1 and Table 2-1 identify the Modem Router Switch’s front-panel components. The 40418 has 12 RJ-11 ports on its front panel. ❸ ❶ ❷ Figure 2-1. The 40418 switch’s front-panel components. Table 2-1. Front-panel components and their functions. -
Page 15: Rear Panel
Switch. The multicolored LEDs are red, green, and orange. ❻ ❼ ❽ ❶ ❷ ❹ ❺ ❸ Figure 2-2. The 40418 switch’s rear-panel components. Table 2-2. Rear-panel components and their functions. Component Function ❶ Power connector Attaches to a 9-VAC power source. - Page 16 CHAPTER 2: Overview Table 2-2 (continued). Rear-panel components and their functions. Component Function ❹ LEDs 1–8 These LEDs serve a dual function. When in the Run Mode, the LED corresponding to the connected port number flashes when the Modem Router Switch rings that port. When in the Program Mode, the interpretation depends on the function you select via the rotary switch.
- Page 17 MODEM ROUTER SWITCH Table 2-2 (continued). Rear-panel components and their functions. Component Function LED 11 Port 1 Unsecure Call Routing (SW 5) *On = Unauthorized calls are routed to Port 1. Off = Unauthorized calls are disconnected. (Default) Flash = Unsecure call is currently routed to Port *Use this for an unsecured fax connection or to monitor the number of unsecured modem call attempts.
- Page 18 CHAPTER 2: Overview Table 2-2 (continued). Rear-panel components and their functions. Component Function ❻ Rotary Program Mode Switch A rotary Program Mode Switch is located in the round opening. It is labeled 0–7 and programs the Router Switch as well as the Security Selection Keys, if used.
- Page 19 MODEM ROUTER SWITCH Table 2-2 (continued). Rear-panel components and their functions. Component Function ❼ ENTER switch Use this switch to enter the commands in the same way that you’d use the Enter key or a mouse click. ❽ 4-position DIP switch Use this switch to append your personal security code to the unique system code that’s factory programmed into your system.
-
Page 20: Operation
CHAPTER 3: Operation 3. Operation 3.1 Answering Inbound Calls The Modem Router Switch answers calls via the following two steps: 1) When a ring signal is received, the switch answers the call, verifies security, and determines which port is requested. 2) Next, the switch rings the selected port and sends a false ring back to the caller. -
Page 21: Programming The Security Selection Key
MODEM ROUTER SWITCH 3.3.2 P ROGRAMMING THE ECURITY ELECTION You can program the Security Selection Key to select various ports. The switch also transfers to the key the unique Modem Router Switch Factory Security Code and the User Code you select via the four-position DIP switches, along with the authorized port numbers. -
Page 22: Programming The Touch-Tone Password
CHAPTER 3: Operation process for each port that you want to enable for that Key. The appropriate LED (1–8) on the Modem Router Switch will light with each selection. 6. After you have completed programming all the Keys, disconnect them and select the Run Mode on the Modem Router Switch (#0, Green LED). -
Page 23: Security Key Selection Mode
MODEM ROUTER SWITCH The typical modem dial command would be ATDTxxx-yyy-nnnn,,#PASS7#ac. This would connect you to port 7. The “,” is a two-second pause command. You may have to experiment to determine how many you require, especially if going through a PBX. Start with two. The “PASS” is your password. The “ac” is an optional AC “power on”... -
Page 24: Optional Ac Power Control Switch
CHAPTER 3: Operation Note that the call-processing time can be decreased by about three seconds if the optional AC power command is used. In other words, add the #0 to all commands. It acts as a terminating statement even without the power unit. 3.4.4 O AC P PTIONAL... -
Page 25: Appendix. Troubleshooting
• Package it carefully. We recommend that you use the original container. • If you are returning the Modem Router Switch, make sure you include everything you received with it. Before you ship for return or repair, contact Black Box to get a Return Authorization (RA) number.