Page 1
SM017 P50XR01E P50XR01U P60XR01E P60XR01U SERVICE MANUAL MANUEL D'ENTRETIEN WARTUNGSHANDBUCH CAUTION: Before servicing this chassis, it is important that the service technician read the “Safety Precautions” and “Product Safety Notices” in this service manual. ATTENTION: Avant d’effectuer l’entretien du châassis, le technicien doit lire les «Précautions de sécurité»...
P50XR01U/E P60XR01U/E PRECAUTIONS Cleaning the plasma screen panel of the monitor Before cleaning the monitor, turn off the monitor and disconnect the power plug from the power outlet. To prevent scratching or damaging the plasma screen face, do not knock or rub the surface with sharp or hard objects.
Page 4
P50XR01U/E P60XR01U/E Digital Terrestrial Television Broadcasting Converting into digital signals enables more channels and various useful features, such as Electric Programme Guide, Digital Teletext, and so on. Further, digital signal can create high quality picture. This logo indicates that the product is compliant with European Digital Broadcasting. DVB is a registered trademark of the DVB Project.
Page 5
P50XR01U/E P60XR01U/E Performance of the FC8 (FRC) Circuit “FC8” is a term for Hitachi’s original LSI having FRC function. “FRC” stands for Frame Rate Converter. By using Frame Rate Converter technology for moving compensation, this circuit creates higher picture quality and has the following functions: 1) Telecine performance (as applying “Film mode”): Judder Reduction...
Page 6
P50XR01U/E P60XR01U/E Handling the HDD (Hard Disk Drive) HDD is a high precision device, and is very susceptible to vibrations or impact. Even if HDD operates normally immediately after it has been subjected to vibrations or impact, a problem may occur after it is used for a while: When servicing, take great care with the following.
Page 7
P50XR01U/E P60XR01U/E Performance of the X-code2U Circuit Part X-code2U makes digital broadcasting compression efficiency and has a function to realise recording for a long time (TS recording); in addition it possesses the MPEG encoding function to cope with analog broadcasting recording. Recording Mode and Recording Time There are 5 recording modes (Fig.1).
P50XR01U/E P60XR01U/E 3. Servicing Lead free solder This product uses lead free solder (unleaded) to help preserve the environment. Please read these instructions before attempting any soldering work. Caution: Always wear safety glasses to prevent fumes or molten solder from getting into the eyes. Lead free solder can splatter at high temperatures (600˚C).
P50XR01U/E P60XR01U/E 4. Component names [Main unit] Front Panel 50” model 60” model 1 Cabinet 2 Panel 3 Remote Control Receiver 4 HDD/Timer Indicating Lamp 5 Power Indicating Lamp 6 Main Power Switch (On the bottom surface) 7 Control Panel and Front Input 8 Desktop Stand 9 Speaker (Option for 60”...
Page 11
P50XR01U/E P60XR01U/E Control Panel (including front input) ” ” Push here to open the door. Push here to open the door. A Push the bottom centre of A Push the bottom centre of the front door to unlock. the front door to unlock. B Pull down the upside of the B Lift it up from the door.
Page 13
P50XR01U/E P60XR01U/E 1 Sub Power Input Select 2 Device Select (TV/DTT, DVD, SAT) You can use this to change the input mode. Press these buttons to select the device (TV/DTT, Multi Picture Press this button to change the picture to multi- DVD, or SAT) to be controlled by this remote picture mode.
P50XR01U/E P60XR01U/E [Terminal Positions] [ 50” model] Rear Power Cord Socket 2 Aerial Socket 3 AV1 4 AV2 5 AV3 6 AV4 7 Monitor Out WOOFER 8 Service use only 9 Service use only Power Swivel Terminal * Not available for 60” model. Optical Out (Digital Audio) HDMI 2 HDMI 3...
Page 15
P50XR01U/E P60XR01U/E [60V SPEAKER SYSTEMS SPECIFICATION] 132.5 117.2 Specifications Model ......SP01G60E Type ......2 way 3 speakers, Bass Reflex Woofer ......100mm cone type ×2 each Tweeter ......25mm dome type Impedance ....6 Max.input power .... 50W RMS input power .... 20W External Dimensions ..
P50XR01U/E P60XR01U/E 5. Adjustment How to get to Adjustment mode Using the remote controller with the set turned on can activate it. Press the Programme Select button "1","GREEN"and "YELLOW" colour button at the same time, and hold for more than 3 seconds The set is displayed adjustment mode.
Page 17
P50XR01U/E P60XR01U/E ADJUST MODE (***-**V-EU)ZZZZ FACT RESET MEMORY INIT WHITE BAL Cool (RGB_Amp ADJUSTING) WHITE BAL Normal WHITE BAL Warm WHITE BAL B/W WHITE BAL Cool,Normal,Warm,B/W(Black&White) Please refer to page 24&25 in detail. ADJUST MODE ADJUST MODE (***-**V-EU)ZZZZ (***-**V-EU)ZZZZ FACT RESET R DRV Cool MEMORY INIT G DRV Cool...
Page 18
P50XR01U/E P60XR01U/E DEVICE Engineer uses only ADJUST MODE ADJUST MODE ADJUST MODE ADJUST MODE (***-**V-EU)ZZZZ (***-**V-EU)ZZZZ (***-**V-EU)ZZZZ (***-**V-EU)ZZZZ DEVICE ITEM DATA DEVICE ITEM DATA DEVICE ITEM DATA DEVICE ITEM DATA ADJUST MODE (***-**V-EU)ZZZZ DEVICE ITEM DATA 3FFF...
Page 19
P50XR01U/E P60XR01U/E HDD Check 1. Select a maintenance mode. 2. Next, select HDD. 3. It becomes the HDD check screen and the following items are displayed. Total Size: It displays the total capacity of the HDD. Used Size: It displays the consumption of the HDD. Power-On Hours Count: The electricity time for HDD Old Rec.
Page 20
P50XR01U/E P60XR01U/E Upgrading the SD The procedure as follows. 1. In sert the MMC/SD card on which the firmware was written to the SD slot of the TV. When obtained from an email and/or a FTP server, a PC and a commercial SD reader/writer are necessary.
Page 21
P50XR01U/E P60XR01U/E 2-7 Fig.3 will be displayed. The upgrading process will continue until the bar is filled. While upgrading, do not turn off the power. Please do not turn off the pow er. Upgrade(SD) Cancel Fig.3 2-8 After upgrade completion, the TV turns off automatically. (Fig.4) The softw are w as upgraded.
Page 22
P50XR01U/E P60XR01U/E Reconfirming Vs and Va voltage values on the Power unit P50XR01U/E and P60XR01U/E do not need adjustment. (Because P50XR01U/E and P60XR01U/E are self-adjusting.) However, Vs and Va voltages require reconfirming on the Power Unit. This page explains the reconfirm procedure. (1) Turn on the TV set and apply pre-heat run more than 1 min on burn-in screen.
Page 23
P50XR01U/E P60XR01U/E RGB Amplitude Adjustment (AV Component Input) Composite video Adjustment Item Preparation Procedure Apply heat-run to the set for more than 20 mins Receive composite video adjustment signal at AV1 before the final adjustment. terminal input. Characters must not be inserted into both patterns Input composite video adjustment signal into of Black and White.
Page 24
P50XR01U/E P60XR01U/E PC input Adjustment PC input Adjustment Item Preparation Procedure Apply heat-run to the set for more than 20 mins Receive the PC adjustment signal at PC input before the final adjustment. terminal. Characters must not be inserted into both patterns Input PC VGA adjustment signal into PC input of Black and White.
Page 25
P50XR01U/E P60XR01U/E Video Colour Temperature Adjustment Item Video Colour Temperature Adjustment (Cool) Preparation Procedure Set the signal generator output to white raster. Perform the following adjustment with the remote (Window ratio: 100%) control. Component signal (576i or 480i) Set the CRT colour analyzer (CA-100) at the centre Video level: 0.700Vp-p of the panel.
Page 26
P50XR01U/E P60XR01U/E Item Video Colour Temperature Adjustment (Warm) Preparation Procedure Set the signal generator output to white raster. Perform the following adjustment with the remote (Window ratio: 100%) control. Component signal (576i or 480i) Set the CRT colour analyzer (CA-100) at the centre Video level: 0.700Vp-p of the panel.
P50XR01U/E P60XR01U/E 6. Troubleshooting Burn-in mode This mode displays test patterns of a single colour raster in turn. These signals are from the built-in generator of the panel. So it can be presumed that the panel has a problem when the screen of Burn-in mode is abnormal.
Page 28
P50XR01U/E P60XR01U/E LED lights blue. Change MAIN PCB or EPM1/2 (cable). Are the voltages of PPM1 and PPM2 If no improvement, go to connector of MAIN PCB normal? Power Supply Unit Troubleshooting [PPM1] Pin1/4/5/6(+5.0V) Pin7/8(+3.3V) [PPM2] Pin1/2/3(+5.6V) Pin7(+10V) Pin9(+16V) Pin13/14/15(+12V) Does PDP Burn-In mode PDP module breaks down operate normally?
Page 29
P50XR01U/E P60XR01U/E Caution: When taking off a PPU1 connector. At first take off the filter board and pull up PPU1 connector. FILTER PCB Check MAIN/TERMINAL PCB Caution: When taking off a PPU1 connector. At first take off the filter board and pull up PPU1 connector.
Page 30
P50XR01U/E P60XR01U/E [Picture troubleshooting] No picture, No colour or dark Are all input no reflected? Change MAIN PCB Digital format signals Analog format signals What is the input abnormal? HDMI Are all Analog format Which is Digital format signals abnormal? signal abnormal? Go to DTT Go to HDMI...
Page 31
P50XR01U/E P60XR01U/E [Picture: RF (analog) troubleshooting] RF (analog tuner) Main tuner Sub tuner Which is tuner abnormal? Sub tuner Main tuner Are the voltages of Are the voltages of pin2(+5V)/3(+30V)/12(+5V)/15(+5V) of pin2(+5V)/3(+30V)/12(+5V)/15(+5V) of UT01(tuner) of Terminal PCB normal? UT02(tuner) of Terminal PCB normal? Change UT01 of Terminal PCB Change UT02 of Terminal PCB Are waveforms at...
Page 32
P50XR01U/E P60XR01U/E [Picture: composite & S-video troubleshooting] Composite and s-video Does the fault appear Change RCA or Mini DIN cable if you change a RCA or Mini DIN cable? Change MAIN PCB Are waveforms at If no improvement, Pin2(CV output) of IM06 of MAIN PCB exchange Terminal PCB normal? Change MAIN PCB...
Page 33
P50XR01U/E P60XR01U/E [Picture: PC RGB troubleshooting] PC RGB Does the fault appear if you change a D-sub cable? Change D-sub cable Are waveforms at Pin4(B input), 10(G input), 16(R input),68(HSYNC),69(VSYNC) of I202 of FC8 PCB OK? Change FC8 PCB If no improvement, exchange Terminal PCB Change MAIN PCB...
Page 34
P50XR01U/E P60XR01U/E [Picture: DTT troubleshooting] DTT (MAIN Tuner) Check DW01 of SLOT PCB lighting? Change MAIN PCB or SLOT PCB Are the voltages of Change SLOT PCB IWP1/IWP2/IW02/IW03IW04 of SLOT [IWP1] Pin4 (+3.3V)/5(+5.6V) PCB normal? [IWP2] Pin2/3 (+5.6V)/7/8(+3.3V) [IW02] Pin2 (+5.6V)/4(+3.3V) [IW03] Pin1/3 (+2.5V)/5(+1.2V) [IW04] Pin1/5 (+3.3V)/4(+2.5V) Are the signals of...
Page 35
P50XR01U/E P60XR01U/E DTT (Sub Tuner) Are the voltages of pin2 (+5V)/3(+30V)/12(+5V)/15(+5 Change UT02 of Terminal PCB V) of UT02 (tuner) of Terminal PCB normal? Are the signals of pin10 (SDA)/9(SCL)/18(IFD_OUT1)/19(IFD Change UT02 of Terminal PCB _OUT2) of UT02 of Terminal PCB normal? Are the signals of R0C1(SUB_SYNC,SUB_EN,SUB...
Page 36
P50XR01U/E P60XR01U/E [Picture: HDMI troubleshooting] HDMI Does the fault appear Change HDMI cable if you change a HDMI cable? Are both inputs abnormal? Change MAIN PCB HDMI1 HDMI2/3 Which is input abnormal? HDMI1 HDMI2/3 Change MAIN PCB Are waveforms at pin13/14/16/17/20/21/23/24 of I405 of MAIN PCB normal? Change SD PCB or EMH (FFC cable)
Page 37
P50XR01U/E P60XR01U/E [Sub Picture troubleshooting] No picture, No colour or dark Change MAIN PCB If no improvement, exchange Terminal PCB [Teletext troubleshooting] No Teletext (analog) Are the signals of Change MAIN PCB QM14/15(CV input) of MAIN PCB normal? Change MAIN PCB If no improvement, exchange Terminal PCB...
Page 38
P50XR01U/E P60XR01U/E [Sound troubleshooting] Sound is abnormal Are all inputs no sound? What is the input abnormal? RF (analog)/ AV1/2/3/4/5 HDMI Same as DTT (Picture) Same as HDMI (Picture) troubleshooting troubleshooting Are all analog inputs no sound? Change MAIN PCB RF(analog tuner) AV1/2/3/4/5 What is the input abnormal?
Page 39
P50XR01U/E P60XR01U/E Are the signals of a PSPK connector of the MAIN PCB normal? Change Speaker or ESP1 (cable) Change MAIN PCB If no improvement, exchange Terminal PCB Main tuner Sub tuner Which is tuner abnormal? Sub tuner Main tuner Are the voltages of pin3 Are the voltages of pin3 (+5V)/15(+30V) of UT02 (tuner) of...
Page 40
P50XR01U/E P60XR01U/E [Optical Out (Digital Audio) troubleshooting] Optical Out (Digital Audio) is no sound Are the voltages of Change MAIN PCB pin1/2/3(+5.6V) of PPM2 If no improvement, connector of MAIN PCB Check Power Supply Unit normal? Is the voltage of pin2 (+5.0V) of Change Terminal PCB HV01 of Terminal PCB normal? Change Optical cable...
Page 41
P50XR01U/E P60XR01U/E [USB troubleshooting] No Picture Does the fault appear Change USB cable or EMH (FFC cable) if you change a USB cable & EMH (FFC cable)? Are the voltages of pin4(+5.6V)/5(+5.0V) of I4U1 Change MAIN PCB of MAIN PCB normal? Change SD PCB If no improvement, exchange MAIN PCB...
Page 42
P50XR01U/E P60XR01U/E [FAN troubleshooting] FAN does not work Are FAN cables Connect cables. connected? Are all the FANs' outward Change the abnormal FAN. appearances normal? Change all the FANs. Do all FANs work? Change Terminal PCB. Check all exchanged FANs using external power.
Page 43
P50XR01U/E P60XR01U/E [HDD troubleshooting] HDD cannot record and play. Do you hear an allophone sound from the HDD? Do you hear rotary sound from the HDD? Does LED (DU01) of MAIN Change the HDD. PCB light? Put back Does HDD work normally? Change MAIN PCB.
P50XR01U/E P60XR01U/E 7. Self-Diagnosis Function PDP panel self-diagnosis function This function is for a PDP panel failure with no picture. It is automatically self-diagnosed that the panel failure occurs. It is shown by power indicator light blinks (blue). The next table shows the PDP PCB in which failure most probably would be indicated according to the number of blinks.
9. Block diagram [For P50XR01U/E] P50XR01U/E P60XR01U/E FC8 BOARD SLOT BOARD SENSOR BOARD 50-INCH PDP PANEL MAIN BOARD MAIN BOARD MAIN BOARD SUB AREA STORAGE MAIN AREA PC PCB TERMINAL PCB INTERNAL iVDR EXTERNAL iVDR POWER UNIT SD BOARD FILTER SWIVEL BOARD STAND...
[For P60XR01U/E] P50XR01U/E P60XR01U/E FC8 BOARD SLOT BOARD SENSOR BOARD 60-INCH PDP FULL MAIN BOARD MAIN BOARD MAIN BOARD HD PANEL SUB AREA STORAGE MAIN AREA PC PCB TERMINAL PCB INTERNAL iVDR EXTERNAL iVDR POWER UNIT SD BOARD SP TRM FILTER BOARD BOARD...
10. Connection diagram [For P50XR01U/E] P50XR01U/E P60XR01U/E NOTE: PARTS MARKED WITH HATCHING ARE NOT MOUNTED IN THIS MODEL. SLOT BOARD FILTER SENSOR BOARD BOARD POWER UNIT FC8 BOARD TERMINAL BOARD MAIN BOARD 50-INCH PDP FULL HD PANEL SWIVEL BOARD FRONT FILTER CONTROL SD BOARD...
Page 51
[For P60XR01U/E] P50XR01U/E P60XR01U/E NOTE: PARTS MARKED WITH HATCHING ARE NOT MOUNTED IN THIS MODEL. SLOT BOARD FILTER SENSOR BOARD BOARD POWER UNIT FC8 BOARD TERMINAL BOARD MAIN BOARD 60-INCH PANEL FRONT FILTER CONTROL SD BOARD BOARD BOARD SP TRM iVDR INTERNAL iVDR SPEAKER...
11. Wiring diagram [For P50XR01U/E only] P50XR01U/E P60XR01U/E MAIN Board (1) The tape is pasted to the positions shown by Install NVS02, NVS03, NVS04, NVS05 & NVS11 beforehand at the positions shown. piling up two pieces. P403 #W021, #W022: NITTO Tape No. 5 To Power Unit U1 W25 (BLACK) L=40mm 2pce.
Page 53
[For P50XR01U/E] P50XR01U/E P60XR01U/E To Power To Power EFAN3 EFAN4 To FAN4 Unit To FAN3 Unit CN61 CN63 EPM2 EFAN2 EFAN1 EPM2 To Power Unit CNPPS To FAN1 To FAN2 EPM1 EPU1 To Power To Power EFAN3 EFAN4 Unit To FAN4 Unit To FAN3 CN61...
Page 68
P50XR01U/E P60XR01U/E Parts marked with hatching are not mounted in this model. I101 GND1 TC90411XBG CK53761U Seine2 PCi-Bus 3/13 PCiAD31 PCiAD31 R601 PCiAD30 PCiAD30 PCiAD29 PCiAD29 2010 PCiAD28 PCiAD28 PCiAD27 PCiAD27 R602 PCiAD26 PCiAD26 PCiAD25 PCiAD25 2010 PCiAD24 PCiAD24 PCiAD23 PCiAD23 R603 PCiAD22...
Page 69
P50XR01U/E P60XR01U/E +2.5V REG 53mA Max 53mA Max D+3.3V SHEET_14 +10V Power Parts marked with hatching are C881 PoWER_2_Td 1.0/6.3 1005 not mounted in this model. I802 I102 121mA Max +2.5V 121mA Max CK37212R YAT-050 CK53853U L812 C822 0.9mA 1.0/6.3 R862 C8C0 Seine2-A 2/9...
Page 70
P50XR01U/E P60XR01U/E I102 I102 YAT-050 YAT-050 Parts marked with hatching are SDA0_3V_400 SHEET_2 SCL0_3V_400 CK53853U CK53853U Seine2_D not mounted in this model. Seine2-A 8/9 LVD HiNT1 R908 Seine2-A 7/9 Logic Port A R920 T1CLKM T1CLKM To Seine2-A voltage for Xtal VDDXo(B2)+11mA max T1CLKP T1CLKP 1010...
Page 71
P50XR01U/E P60XR01U/E Parts marked with hatching are not mounted in this model. LVDS, LVTTL I/F T S I/F LVDS Input *I101 TS i/F from POD to Tenko4 C/I I/F TSPi_SYNC TC90411XBG TSPi_EN CK53761U TSPi_D0 *PA01 TSPi_CLK Seine2 501786-80V 6/13 LVDS RX input Tenko4 for recording EA03004R...
Page 72
P50XR01U/E P60XR01U/E Parts marked with hatching are Panel-IF LVDS µ IPS - (VSYNC_60Hz) VSYNC PNLoN (5)pin LCD_Go not mounted in this model. BL_oN (6)pin BL_oN LAMPCNT (7)pin I-PWM PNLRST (8)pin CPU_Go *EC02 502386-9H RA1- RA1+ RB1- P# EA04058R RB1+ *RC13 SHEET_5 RC1- PNLRST...
Page 73
P50XR01U/E P60XR01U/E PoWER_2_Td Parts marked with hatching are SHEET_14 LE01 116mA Power not mounted in this model. 30uH D+3.3V 2125 2.5V_Reg. IE09 25mA LE02 3.0V_Reg. CK37606R IE10 600uH 1608 XE01 CK37212R CE10 27.000MHz 0.1/16 CE11 1005 1.0/6.3 FCX-03 SHEET_11 1005 26 25 CE09 D+2.5V...
Page 74
P50XR01U/E P60XR01U/E CF10 4.7/6.3 Parts marked with hatching are IF01 AK4121A *RFR8 *RFR9 RF11 560 not mounted in this model. +3.3V FILT CF11 AVSS DVSS 0.001 1005 *IF09 SN74LVC244APW TVDD SMUTE MCKL *RFG0 Seine2 A-chip RF12 0 DEM0 OLRCK DEM1 OBICK RF16 *RFG1...
Page 84
P50XR01U/E P60XR01U/E PTXT 501331-15V Parts marked with hatching are IR13 TK11133CSC not mounted in this model. +5.6V Vcont +3.3V RR72 +3.3V CR01 Vout IR02 0.1/16 150mA 1010 1005 CK48871U CK37216R GND2 RR70 1010 LR06 VDD-1 VSS-54 +5.0V 0.5mm 47uH 1.1mA CR02 0.1/16 GND2...
Page 85
P50XR01U/E P60XR01U/E MAIN Board (STORAGE Section) Circuit Audio/Video Capture NOTE: PARTS MARKED WITH HATCHING ARE NOT MOUNTED IN THIS MODEL. PCI BUS TenkoIV PCI IU01 Slave Adrs. 0x34 RK01 EP2C35F484C8N JTAG Connector RK02 Tenko IV (EP2C35F484C8N) 1/6 PCI I/F PCiAD0 PCiAD0 PCi_AD[0] PCiAD0...
Page 92
P50XR01U/E P60XR01U/E FC8 Board Circuit NOTE: PARTS MARKED WITH HATCHING ARE NOT MOUNTED IN THIS MODEL. SM017 FC8 BOARD CIRCUIT - SHEET 1...
Page 93
P50XR01U/E P60XR01U/E NOTE: PARTS MARKED WITH HATCHING ARE NOT MOUNTED IN THIS MODEL. FC8 BOARD CIRCUIT - SHEET 2 SM017...
Page 94
P50XR01U/E P60XR01U/E NOTE: PARTS MARKED WITH HATCHING ARE NOT MOUNTED IN THIS MODEL. FC8 BOARD CIRCUIT - SHEET 3 SM017...
Page 95
P50XR01U/E P60XR01U/E NOTE: PARTS MARKED WITH HATCHING ARE NOT MOUNTED IN THIS MODEL. FC8 BOARD CIRCUIT - SHEET 4 SM017...
Page 96
P50XR01U/E P60XR01U/E NOTE: PARTS MARKED WITH HATCHING ARE NOT MOUNTED IN THIS MODEL. FC8 BOARD CIRCUIT - SHEET 5 SM017...
Page 97
P50XR01U/E P60XR01U/E NOTE: PARTS MARKED WITH HATCHING ARE NOT MOUNTED IN THIS MODEL. FC8 BOARD CIRCUIT - SHEET 6 SM017...
Page 98
P50XR01U/E P60XR01U/E CONTROL Board Circuit MENU/SELECT INPUT_SEL VOL_DOWN VOL_UP CH_DOWN CH_UP POWER_ON PLAY/STOP SNC9 SNC8 SNC7 SNC6 SNC5 SNC4 SNC3 SNC2 SNC1 Parts marked with hatching are SKHMPUE010 SKHMPUE010 SKHMPUE010 SKHMPUE010 SKHMPUE010 SKHMPUE010 SKHMPUE010 SKHMPUE010 SKHMPUE010 not mounted in this model. RNC4 RNC5 RNC6...
Page 99
P50XR01U/E P60XR01U/E SLOT Board Circuit Parts marked with hatching are not mounted in this model. SM017 SLOT BOARD CIRCUIT...
Page 100
SD Board Circuit [P50XR01U/E Only] P50XR01U/E P60XR01U/E +3.3V IQ03 Parts marked with hatching are RQ41 not mounted in this model. Molex (Normal type) JQ01 501331-12V CK55511R IQ01 TC7SG17FU SDCLK TC7MBL3245AFK XQ01 500998-0900 GND1 NFL21SP206X1C3 RQ01 SDCMD 2125 EY01772R RQ05 RQ06 RQ13 SDDAT0 DATA2...
Page 101
SD Board Circuit [P60XR01E/U Only] P50XR01U/E P60XR01U/E +3.3V Parts marked with hatching are IQ03 RQ41 not mounted in this model. Molex (Normal type) JQ01 CK55511R 501568-12H IQ01 TC7SG17FU SDCLK TC7MBL3245AFK 500998-0900 XQ01 GND1 RQ01 NFL21SP206X1C3 SDCMD 2125 EY01772R RQ05 RQ06 RQ13 SDDAT0 DATA2...
Page 102
PC, SPEAKER [P60XR01E/U Only], FILTER, LED and SWIVEL [P50XR01E/U Only] Board Circuits +5.0V LED BOARD COLOUR CONTROL DN01 PWERLED0 JF60 PF60 KFX2 0 YKD21-0284N PA-04V CFX1 DN02 BLUE ALARMLED0 ER00661 EA02803R 2200/16 LFX1 PWERLED1 Side:Lout-P Side:Lout-P DN03 MLED1R Side:Lout-N Side:Lout-N...
Page 103
P50XR01U/E P60XR01U/E TERMINAL Board Circuit NOTE: RT07 RT06 PARTS MARKED WITH HATCHING ARE NOT MOUNTED IN THIS MODEL. RT09 RT11 LT03 LT04 DT01 IT16 7E06NB 2125 RB160L-40 RT58 XT11 TK11150CSC RT51 RT52 NFM18PC105R0J3 BA02681R RT54 1608 16 15 Vcont RT12 IT15 CK37218R VT+30V REG...
Page 104
[For P50RX01E/U] P50XR01U/E P60XR01U/E RY74 RY79 NOTE: Temp.Sensor I/F PC BOARD XY20 SC200JT 2125 PARTS MARKED WITH HATCHING GND1 RY80 To FAN1 To FAN2 To FAN3 To FAN4 ARE NOT MOUNTED IN THIS MODEL. XY21 SC200JT 2125 RY81 PTMP1 *PFA1 *PFA2 *PFA3 *PFA4...
Page 105
[For P60XR01E/U] P50XR01U/E P60XR01U/E RY74 PC BOARD RY79 NOTE: XY20 SC200JT 2125 Temp.Sensor I/F PARTS MARKED WITH HATCHING GND1 RY80 To FAN1 To FAN2 To FAN3 To FAN4 ARE NOT MOUNTED IN THIS MODEL. XY21 SC200JT 2125 PTMP1 *PFA1 RY81 *PFA2 *PFA3 *PFA4...
Page 106
P50XR01U/E P60XR01U/E SHEET_2 SHEET_1 IR OUTPUT DVI_L/R NOTE: LX01 +5.0V 0.5mm XX01 PARTS MARKED WITH HATCHING CX02 RX01 2125 QX03 NFL21SP506X1C3 1.0/10 JX05 RX08 2125 2SA1774 ARE NOT MOUNTED IN THIS MODEL. LGT1509-0200F IX03 QX01 LX02 LGT1509-0200F 2SC4617 TC7SG17FU CX03 RX06 1.0/10 1608...