Oregon Scientific EMR801 User Manual

2. Wall mount hole
3. Battery compartment
4. RESET hole
5. CHANNEL switch
Wireless Indoor and Outdoor
Thermometer with Digital Clock
GETTING STARTED
Model: EMR801
SOLAR PANEL
The solar panel is an energy saving feature, which is an
environmentally friendly way to provide additional power to
USER MANUAL
the main unit and prolongs battery life. However, it cannot
replace battery power entirely.
EN
OVERVIEW
INSERT BATTERIES
FRONT VIEW 1. Remove the battery compartment.
2.
1
3. Press RESET after each battery change.
9
8
2
SET CLOCK
7
3 1. Press and hold MODE for 2 seconds.
2. Press
4 3. Press MODE to confirm.
4. The settings order is: 12/24 hour format, hour and
6
5
REMOTE SENSOR
To set up the sensor:
1. Solar panel
1. Open the battery compartment and insert the battery,
2. Outdoor temperature
3. Indoor temperature / Time
2. Press RESET.
4. Ice alert indicator
3. Close the battery door.
5. : Increase value ; auto-toggle of indoor temperature
4. Place the sensor within 30 m (98 ft) of the main
and time
6. MODE: Enter setting mode; toggle between indoor
temperature and time
7. Main unit low battery indicator
8. Remote sensor low battery indicator
location on the exterior of the home at a height of not more
than 1.5 m (5 ft) and which can shield it from direct sunlight
9. Remote sensor reception indicator
or wet conditions for an accurate reading.
BACK VIEW
1
2
6 3
5 4
consumer grade lithium batteries in temperatures below
1. Wall-mount hole freezing.
2. Mounting magnet
3. °C/°F: Select temperature unit
SENSOR DATA TRANSMISSION
4. Battery compartment
To search for a sensor:
5. Table stand
Press and hold MODE +
6. RESET: Reset unit to default settings
The sensor reception icon in the remote sensor area
shows the status:
REMOTE SENSOR
2
1
4
3
5
many factors. You may need to experiment with various
locations to get the best results.
1. LED status indicator
TIME AND INDOOR TEMPERATURE DISPLAY
To enable auto-toggle display of time and indoor
temperature:
Press and hold
To disable auto-toggle display of time and indoor
temperature:
Press MODE.
To manually toggle between time and indoor
temperature display:
Press MODE.
ICE WARNING
If the sensor falls between 3°C to -2 °C (37°F to 28°F), the
Insert the batteries, matching the polarities.
green LED indicator will flash, and will stop flashing once
the temperature is out of this range.
MEANING
LOCATION
NOTE
Indoor temperature / time Main unit batteries low
prevent flashing of LED, select channel 2 or 3 on outdoor
area
sensor.
Outdoor temperature area Sensor batteries low
RESET
Press RESET to return to the default settings.
to change values.
PRECAUTIONS
•
minute.
•
•
•
matching the polarity.
•
•
unit using the table stand , mounting magnet or wall
mount. •
•
TIP Ideal placements for the sensor would be in any
•
•
•
•
1.5 m (5 ft)
NOTE
the contents of the user manual are subject to change
without notice.
NOTE
in all countries. For more information, please contact your
local retailer.
NOTE
Use alkaline batteries for longer usage and
SPECIFICATIONS
for 2 seconds.
ICON DESCRIPTION
Main unit is searching
OUT OUT
for sensor(s).
A channel has been
OUT OUT OUT OUT
found.
The sensor cannot be
OUT
found.
TIP The transmission range may vary depending on
ABOUT OREGON SCIENTIFIC
Visit our website (www.oregonscientific.com) to learn
more about Oregon Scientific products. If you're in the US
and would like to contact our Customer Care department
for 2 seconds.
directly, please visit: www2.oregonscientific.com/service/
support
For international inquiries, please visit:
www2.oregonscientific.com/about/international
FCC STATEMENT
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) This
device must accept any interference received, including
interference that may cause undesired operation.
WARNING
approved by the party responsible for compliance could
void the user's authority to operate the equipment.
As ice alert is only applicable to channel 1, to
NOTE This equipment has been tested and found
to comply with the limits for a Class B digital
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
Do not subject the unit to excessive force, shock, dust,
is no guarantee that interference will not occur in a
temperature or humidity.
particular installation. If this equipment does cause harmful
Do not cover the ventilation holes with any items such
interference to radio or television reception, which can be
as newspapers, curtains etc.
determined by turning the equipment off and on, the user
Do not immerse the unit in water. If you spill liquid over is encouraged to try to correct the interference by one or
it, dry it immediately with a soft, lint-free cloth. more of the following measures:
Do not clean the unit with abrasive or corrosive •
materials.
•
Do not tamper with the unit's internal components.
This invalidates the warranty.
•
Only use fresh batteries. Do not mix new and old
batteries.
Images shown in this manual may differ from the
•
actual display.
When disposing of this product, ensure it is collected
separately for special treatment.
Placement of this product on certain types of wood
DECLARATION OF CONFORMITY
may result in damage to its finish for which Oregon
The following information is not to be used as contact
Scientific will not be responsible. Consult the furniture
for support or sales. Please visit our website at www2.
manufacturer's care instructions for information.
oregonscientific.com/service for all enquiries.
The contents of this manual may not be reproduced
without the permission of the manufacturer.
We
Name:
Do not dispose old batteries as unsorted municipal
Address:
waste. Collection of such waste separately for special
treatment is necessary.
Telephone No.:
Please note that some units are equipped with a
battery safety strip. Remove the strip from the battery
declare that the product
compartment before first use.
Product No.:
Product Name:
The technical specifications for this product and
Manufacturer:
Address:
Features and accessories will not be available
is in conformity with Part 15 of the FCC Rules.Operation is
subject to the following two conditions: 1) This device may
not cause harmful interference.2) This device must accept
any interference received, including interference that may
TYPE DESCRIPTION
cause undesired operation.
MAIN UNIT
L x W x H 68 x 24 x 96 mm
(2.68 x 0.94 x 3.78 in)
Weight 80 g (2.82 oz) without battery
Temperature range -5°C to 50°C (23°F to 122°F)
Signal frequency 433 MHz
Power 2 x UM-4 (AAA)
1.5 V batteries
REMOTE UNIT (THN132N)
L x W x H 96 x 50 x 22 mm
(3.78 x 1.97 x 0.87 in)
Weight 62 g (2.22 ounces)
Transmission range 30 m (98 ft) unobstructed
Temperature range -20°C to 60°C (-4°F to 140°F)
Power 1 x UM-3 (AA) 1.5 V batteries
Thermomètre extérieur et intérieur
FR
VUE D'ENSEMBLE
FACE AVANT
Changes or modifications not expressly
device,
1. Panneau solaire
2. Température extérieure
3. Température intérieure / heure
4. Indicateur d'alerte du niveau de gel
5.
l'heure et de la température intérieure
Reorient or relocate the receiving antenna.
6. MODE : Permet d'entrer dans le mode Réglages,
Increase the separation between the equipment and
d'alterner entre l'heure et la température intérieure
receiver.
7. Indicateur de faiblesse des piles de l'appareil
Connect the equipment into an outlet on a circuit
principal
different from that to which the receiver is
8. Indicateur de faiblesse de la pile de la sonde sans fil
connected.
9. Indicateur de réception de la sonde sans fil
Consult the dealer or an experienced radio / TV
technician for help.
FACE ARRIERE
Oregon Scientific, Inc.
19861 SW 95th Ave.,Tualatin,
Oregon 97062 USA
1-800-853-8883
EMR801
Wireless Indoor and Outdoor
Thermometer with Digital Clock
IDT Technology Limited
Block C, 9/F, Kaiser Estate,
Phase 1,41 Man Yue St.,
Hung Hom, Kowloon,
1. Trou de fixation murale
Hong Kong
2. Aimant de montage
3. °C / °F : Permet de sélectionner l'unité de mesure de
la température
4. Compartiment des piles
5. Support de table
6. RESET (REINITIALISER) : Réinitialise l'appareil aux
réglages par défaut
SONDE SANS FIL
1. Indicateur de statut LED
2. Trou de fixation murale
3. Compartiment des piles
4. Fente RESET (Réinitialiser)
5. Bouton CHANNEL (CANAL)
sans fil à horloge numérique
Modèle : EMR801
Manuel de l'utilisateur
1
9
8
2
7
3
4
6
5
: Augmente la valeur, alternance automatique de
1
2
6 3
5 4
2
1
4
3
5