Related Manuals for Oregon Scientific BPW128
Summary of Contents for Oregon Scientific BPW128
- Page 1 mmHg / min LOG BOOK Age: Weight: kg/lbs...
- Page 2 LEGEND : - FAST INCREMENT - FLASHING - PRESS BUTTON BOLD BOLD - PRESS AND HOLD BUTTON LEGENDE : - AUGMENTATON RAPIDE - CLIGNOTEMENT BOLD - APPUYER SUR LE BOUTON BOLD - APPUYER SANS LACHER SUR LE BOUTON LEYENDA : - INCREMENTO RÁPIDO - DESTELLANDO BOLD...
- Page 3 MODEL: BPW128 USER’S MANUAL INTRODUCTION Thank you for purchasing the Wrist Blood-Pressure Monitor (BPW128). This unit has been constructed using reliable circuitry and durable materials. Used properly, this unit will provide years of satisfactory use. Before use please note: This device is intended for non-invasive measuring and monitoring of arterial blood pressure.
- Page 4 DESCRIPTION AND FUNCTION OF PARTS A. Liquid Crystal Display (LCD) and protective cover - Large easy-reading display - 5 functional symbols - Systolic [SYS/mmHg], Diastolic [DIA/mmHg], Mean [MAP/mmHg], Pulse [pul/min.]and date & time display. B. Battery compartment Houses two (2) LR03 /AAA/ UM4 size 1.5V batteries Button - For time adjustment.
-
Page 5: Display-Symbol Description
DISPLAY-SYMBOL DESCRIPTION Symbol Description Appears when Memory Mark measurement value is recalled from memory Appears when batteries Weak Battery should be replaced Appears when inflating Inflating Mark until pressure is enough Appears when cuff air is Air releasing exhausting Pulse Mark Shows the pulse rate per minute INSTALLING BATTERIES... - Page 6 1. Remove all watches, jewelry, etc. prior to attaching the wrist monitor. Clothing sleeves should be rolled up and the cuff should be wrapped on bare skin for correct measurements. 2. Apply cuff to left wrist with palm facing up. 3.
-
Page 7: What Is Mean Arterial Pressure
BLOOD PRESURE DEFINITIONS Information obtained from the World Health Organization (WHO) Hypertension systolic over 160 (high pressure) diastolic over 95 Hypertonia systolic 140-159 (Border value) diastolic 90-94 Hypotension Normal (low pressure) range systolic under 90 systolic 139 diastolic 89 Systolic (mmHg) please note: -Hypotension value is for reference only. - Page 8 MEASUREMENT With the individual in a sitting position and with the cuff attached as previously mentioned, a blood pressure reading can be obtained. Note: For accurate pressure measurement, take blood-pressure readings in a seated position. Avoid the measurement is being taken. Ensure that the lower arm is raised so that the upper edge of the cuff is on the same level as the heart.
- Page 9 HOW TO TAKE MEASUREMENT Refer to Fig1 Fig1 2sec Fig1...
- Page 10 Note: 1. Remove all watches, jewelry, etc. prior to attaching the wrist monitor. Clothing sleeves should be rolled up and the cuff should be wrapped on bare skin for correct measurements. 2. Apply cuff to left wrist with palm facing up. 3.
-
Page 11: How To Set The Time
HOW TO SET THE TIME Refer to Fig3 mode Fig 3... -
Page 12: Error Messages
Note: 1. Press and hold the [ ]button for 2 seconds, the display will flash 12h or 24h. 2. Press the [ ] button to select either 12 hour or 24 hour display. 3. Press the [ ] button to accept 4. -
Page 13: Maintenance, Cleaning And Care
MAINTENANCE, CLEANING AND CARE When handled properly, this unit is engineered to give years of satisfactory service. Here are a few product care instructions: - When not in use, store the unit in the protective plastic container provided with your purchase. - Do not immerse the unit in water. -
Page 14: Symbol Descriptions
: IDT Technology Limited 9/F Kaiser Estate Phase 1 41 Man Yue Street Hunghom, Kowloon Hong Kong Customer Assistance Oregon Scientific, Inc. 19861 SW 95th Place Tualatin, OR 97062 U.S.A. website address: www.oregonscientific.com Should you require assistance regarding this product and its operation, please contact our Customer Care Department at 1-800-853-8883 or via email at helpme@oscientific.com. - Page 15 measurement again, ensure that the cuff is properly attached, the arm is in the proper position and that movement has been minimized during the measurement process. If the device does not function: Check that the unit is on. After about 3 minutes of inactivity, the unit will automatically turn off.