Potenza Alimentazione Esempio Gli LRx 2.4 e 2.9 sono amplificatori di potenza stereofonici per auto. La sezione di alimentazione e gli stadi finali, che possono lavorare anche in mono, erogano un’elevatissima corrente Configurazioni d’uscita con potenze comprese fra 135 e 900 W. Ogni dettaglio costruttivo, dai crossover...
Per l’Italia - supporto.tecnico@elettromedia.it Per l’estero - support@elettromedia.it • Viti di fissaggio con testa a croce autofilettanti 3,9x16 mm • Punta per avvitatori specifica con asta allungata. • Fusibile di ricambio da 40 A (LRx 2.4) o da 60 A (LRx 2.9)
LRx 2.4 LRx 2.9 The Universal Sound Manuale d’uso Precauzioni Generali • Per fissare il collegamento di massa (-) in modo corretto usate una vite già presente sulla parte metallica del veicolo, rimuovete ogni residuo di vernice o grasso se necessario, assicurandovi con un tester che vi sia continuità...
Pannello Ingressi ECI - Easy Common Interface Per entrambi i pannelli vale la stessa procedura: Audison introduce una novità assoluta nella gestione degli ingressi degli amplificatori LRx. ECI è un’interfaccia intercambiabile con una morsettiera comune estremamente facile da utilizzare. Gli LRx sono dotati di un duplice pannello ingressi reversibile che può essere utilizzato a seconda delle esigenze.
In dotazione con ogni amplificatore ci sono due mascherine, una sagomata per il Il pannello che contiene i terminali di alimentazione e di potenza è protetto da un guscio passaggio dei cavi e una chiusa con il logo Audison per la protezione totale dei cavi di asportabile e da una mascherina.
The Universal Sound Manuale d’uso Descrizione Come si montano i connettori portafaston 1_ Fusibile di protezione: 40 A (LRx 2.4) / 60 A (LRx 2.9); 2_ Flangia protettiva anticortocircuito; 3_ - Power (Ground): morsetto per il collegamento del polo negativo d’alimentazione dell’amplificatore.
LRx 2.4 LRx 2.9 The Universal Sound Manuale d’uso PRE Input Pannello Controlli Auto Turn-ON con SPK ON Il pannello che contiene i controlli dell’amplificatore è protetto da un guscio asportabile. L’amplificatore può essere Come togliere il guscio acceso con la funzione...
Filtered PRE OUT BYPASS, FILTER HI-PASS Mono L + R INPUT R LO-PASS OUT BYPASS FILTER Pannello Controlli LRx 2.4 e LRx 2.9 Out Mode Level 0.3÷5 V Stereo Mode 4 Ω PRE OUT: 5 V RMS PRE OUT BYPASS,...
LRx 2.4 LRx 2.9 The Universal Sound Manuale d’uso Filter AMP LO 12 dB Config. 7, 8, 9 PRE OUT LO 12 dB Config. 3, 6, 9 Gli LRx stereofonici hanno una sezione di filtro versatile e indipendente. Una volta scelta la configurazione dell’uscita di potenza del finale, è possibile regolare l’uscita PRE a proprio piacimento, a tutto vantaggio della facilità...
LRx 2.4 LRx 2.9 The Universal Sound Manuale d’uso LEDS AMP LO 24 dB Config. 7, 8, 9 PRE OUT LO 24 dB Config. 3, 6, 9 Logo MONO 24 dB/Oct. 50÷500 Logo Logo MONO 24 dB/Oct. 500÷5k INTERROMPERE L’ASCOLTO...
LRx 2.4 LRx 2.9 The Universal Sound Manuale d’uso Protection LEDS Installazione Fissaggio dell’amplificatore CONTROLLARE LA TEMPERATURA DELL’AMBIENTE Per un montaggio totalmente a scomparsa, la sede delle viti Lampeggio è all’interno del perimetro di installazione. Fissate le viti lento T: Protezione termica 70÷75°C...
Dima di foratura Come far passare i cavi di segnale sotto l’amplificatore Se si utilizzano i cavi di interconnessione CONNECTION Audison dopo aver collegato Perimetro per il montaggio a filo del pannello i connettori RCA fissare l’Y BLOCK su uno dei pioli predisposti.
I prodotti CONNECTION Audison sono sicuramente i più versatili e completi, studiati e realizzati per far rendere al massimo qualsiasi installazione in abbinamento con gli amplificatori Audison.
LRx 2.4 LRx 2.9 The Universal Sound Manuale d’uso Configurazioni LRx 2.4 e LRx 2.9 2 vie monoamplificato PRE OUT Config. Per l’impostazione degli switch sul pannello di controllo, fate riferimento agli schemi Full Full della sezione Filter di pagina 17 e seguenti.
Page 17
LRx 2.4 LRx 2.9 The Universal Sound Manuale d’uso 3 vie multiamplificato + Sub 2 vie + Sub biamplificato INPUT (ECI-L or ECI-H) FRONT FRONT LEFT PRE OUT FRONT RIGHT Optional use INPUT (ECI-L or ECI-H) FRONT MID-HIGH LEFT MID-HIGH RIGHT...
Page 18
LRx 2.4 LRx 2.9 The Universal Sound Manuale d’uso Multiamplificazione attiva: Front 3 vie + Rear 2 vie + Sub 3 vie Front multiamplificato attivo + Rear + Sub IN A Ch (ECI-L or ECI-H) MID-HIGH FRONT FRONT TWEETER LEFT...
LRx 2.4 LRx 2.9 The Universal Sound Manuale d’uso Caratteristiche tecniche Sezione d’alimentazione Tensione 11÷15 VDC 11÷15 VDC Assorbimento minimo 1.3 A 1.7 A Assorbimento da spento 0.02 mA 0.02 mA Assorbimento @ 14.4 VDC 36 A 65 A (Potenza musicale MAX) 7÷15 VDC (1 mA)
Page 20
- Potenza nominale misurata utilizzando una batteria da 12 VDC con un carico di 4 Ohm e tutti i canali in funzione. The Universal Sound Audison measurement standard Power measures taken according to Audison standard, 2005 edition - 12 VDC and 14.4 VDC; - 1 kHz or crossover cut-off frequency;...
Page 21
How to run the cables under the amplifier Audison logo in reverse LRx 2.4 and 2.9 are stereo car power amplifiers. Their power supply section and final stages, which can also work in a mono configuration, provide very high output current and can produce Connection cables between 135 and 900 W power.
If, after reading it, you still have questions regarding this product, go and see your AUDISON dealer. • Cable guide clip In case you need more information, you can contact Audison after sales service by email at the following addresses; • Fast-on taker connectors In Italy –...
• To prevent all problems, use very good quality cables, connectors and accessories, • Before installing the amplifier, make sure you carefully read and choosing them in CONNECTION Audison catalogue. understand all instructions. • When installation is over, and before plugging the main power supply fuse, check •...
ECI – Easy Common Interface Modules Instructions are the same for both panels: The LRx amplifier input section is totally new. Audison created ECI, an interchangeable interface module that is very easy to use. There are two different modules and you can choose what type of signal input to use to drive the amplifier.
Two plates are supplied with the amplifier. One is formed for exposed cable routing; The panel with the power supply and speaker terminals is protected by a removable cover the other, with the Audison logo, is closed for protecting and hiding the cables. and end plate.
Owner’s manual Power Supply and output terminal description How to mount fast-on taker connectors 1_ Protection fuse: 40 A (LRx 2.4) / 60 A (LRx 2.9); 2_ Anti-short circuit protective shield; 3_ - Power (Ground): terminal block for the amplifier power supply negative pole connection.
Place accurately SUB VOL connector into the proper socket of the amplifier. Push to click Push to click How to replace the fuse After taking off the cover, remove the fuse with the Audison multispanner supplied with the amplifier.
Filtered PRE OUT BYPASS, FILTER HI-PASS Mono L + R INPUT R LO-PASS FILTER OUT BYPASS LRx 2.4 and LRx 2.9 control panel Out Mode Level 0.3÷5 V Stereo Mode 4 Ω PRE OUT: 5 V RMS PRE OUT Right...
LRx 2.4 LRx 2.9 The Universal Sound Owner’s manual Filter AMP LO 12 dB Config. 7, 8, 9 PRE OUT LO 12 dB Config. 3, 6, 9 LRx stereo amplifiers have a flexible, independent filter section. After choosing the amplifier power output configuration, you can easily select the signal to the PRE output.
LRx 2.4 LRx 2.9 The Universal Sound Owner’s manual Diagnostic LED description AMP LO 24 dB Config. 7, 8, 9 PRE OUT LO 24 dB Config. 3, 6, 9 Logo MONO 24 dB/Oct. 50÷500 Logo Logo MONO 24 dB/Oct. 500÷5k...
LRx 2.4 LRx 2.9 The Universal Sound Owner’s manual Diagnostic LED description Installation Amplifier fixing CHECK ENVIRONMENTAL TEMPERATURE For hidden installation the mounting holes for the screws Slow are inside the amplifier outline. Secure the screws with T: Thermal protection...
Mounting template How to run the cables under the amplifier If you use CONNECTION Audison interconnects, attach Y BLOCK on one of the mounting Perimetro per il montaggio a filo del pannello pins of the amplifier after plugging in RCA connectors.
CONNECTION Audison products are the most flexible and complete; they are designed and built in order to get the best out of every installation, especially when used with Audison amplifiers.
LRx 2.4 LRx 2.9 The Universal Sound Owner’s manual Configuration LRx 2.4 and LRx 2.9 2 way mono-amplified PRE OUT Config. For setting the control panel switches properly, refer to the diagrams in the Filter section, starting on page 53.
Page 36
LRx 2.4 LRx 2.9 The Universal Sound Owner’s manual 2 way + Sub bi-amplified 3 way multi-amplified + Sub INPUT (ECI-L or ECI-H) FRONT FRONT LEFT PRE OUT FRONT RIGHT Optional use INPUT (ECI-L or ECI-H) FRONT MID-HIGH LEFT MID-HIGH RIGHT...
Page 37
LRx 2.4 LRx 2.9 The Universal Sound Owner’s manual Active multi-amplification: Front 3 way + Rear 2 way + Sub 3 way active Front multi-amplified + Rear + Sub IN A Ch (ECI-L or ECI-H) MID-HIGH FRONT FRONT TWEETER LEFT...
LRx 2.4 LRx 2.9 The Universal Sound Owner’s manual Technical specifications Power supply 11÷15 VDC Voltage 11÷15 VDC Minimum idling current 1.3 A 1.7 A Idling current when off 0.02 mA 0.02 mA 36 A Consumption @ 14.4 VDC 65 A...