Advertisement
POWER UP
To power up thermostat:
CHECKING GROUND FAULT CIRCUIT INTERRUPTER (GFCI)
OPERATION
The thermostat has 4 different buttons to control the floor temperature. The
and
buttons increase or decrease the setpoint temperature. The
buttons are used to store and recall two temperature settings.
• Default values
To erase the recorded setting temperatures (
lues by the default ones,
28 °C (82 °F) and
ton while pressing and releasing the RESET button. Then release the
• Setting a setpoint temperature
Press once the
or
button to see the setpoint temperature on display. Every
subsequent press will change the setpoint temperature by one degree.
• Recording setpoint temperature for
(VACATION) settings
By recording the setpoint temperatures you will be able to go from the
setting to the
or
setting by simply pressing the
) for
.
• Recording a setpoint temperature for the
Select chosen setpoint temperature by using
pressing on the
button (2 to 3 seconds) until icon appears on display.
When power is applied for the first time,
the display must show the time 00:00,
the floor temperature and the manual
mode icon (
). Other information
might show up on the display if installa-
tion is defective or does not comply with
the instructions. The warning light (GFI)
must be off.
The message L0 or HI will appear on
the display if the temperature sensor is
defective or the temperature is below 0
°C (32 °F) or higher than 60 °C (140
°F). Also, the heating indicator will be
present on display and the relay will be
closed (current going in the load).
Adjust the setpoint temperature until
heating indicator (
) appears on
display. Press TEST button. The test is
conclusive if the warning light (GFCI)
on the thermostat is ON and power to
the load is cut-off. If these events do not
occur, check the installation. Press on
RESET button to reset the GFCI.
If the GFCI test fails:
Check the load wires. The thermostat
must be in heating mode to carry out
the test (heating indicator ON).
The GFCI test should be carried out
monthly. If the test fails, cut off
the electric power to the heating
system and
call customer service or
return the thermostat to your supplier
for verification. If the warning light
comes on during normal operation, cut
off power to the heating system and
have an electrician verify the installa-
tion.
and
) and replace their va-
18 °C (64 °F) press the
button.
(COMFORT) ,
(ECONOMIC) and
or
button or (
(COMFORT) setting
and
buttons. Keep
• Recording a setpoint temperature for the
Select chosen setpoint temperature by using
pressing on the
button (2 to 3 seconds) until icon appears on display.
• Recording a setpoint temperature for the
To program the Vacation temperature, select the desired degree using the
buttons and press on the
icon is displayed (app. 3 seconds).
NOTE: When the temperature setting used is
the
or
buttons to change the setpoint temperature without changing the
recorded temperature.
• Recalling stored setpoint temperatures
Once stored, the setpoint temperatures can be recalled simply by selecting the
or
button or both
CHARACTERISTICS
Model:
Supply:
Load:
Power:
Ground fault circuit interrupter (GFCI):
Approvals:
Display range:
Setting range:
Default setting:
Default setting:
Storage:
Temperature regulation:
Precision:
AUBE TECHNOLOGIES INC. ONE (1) YEAR LIMITED WARRANTY
This product is warranted against material defects and workmanship in
normal use for a period of one year, from the date of the original purchase from
authorized dealers. During this period, AUBE technologies inc. will repair or
replace the product with a new or of equivalent quality at AUBE'S option,
without charge, any product proven defective in normal use.
Warranty does not cover transportation costs. Nor does it cover a product
subjected to misuse or accidental damage. This warranty does not cover the cost
and
of installation, removal or reinstallation.
This limited warranty is in lieu of all other warranties, obligations or liabilities
expressed or implied by the company. In no event shall AUBE technologies inc.
be liable for consequential or incidental damages resulting from
installation of this product. Some states or provinces do not allow limitations on
but-
how long an implied warranty lasts, or the exclusion or limitation of
incidental or consequential damages, so the above exclusions or limitations may
not apply to you.This warranty gives you specific legal rights and you may also
have other rights which vary from state to state.
The defective product and the original sale receipt must be returned to the
original dealer or shipped pre-paid, insured and addressed to:
•Aube technologies inc. • Customer Service • 705, Av. Montrichard
• Iberville (Quebec) • J2X 5K8
and
If you have any questions concerning the installation or programming of this
product, please call our technical assistance at (450) 358-4600 for the Montreal
1-800-831-AUBE
area or
8:30 AM and 5:00 PM Eastern time.
(ECONOMIC) setting
and
(VACATION) setting
and
buttons simultaneously until the
or
or
and
for
setpoint.
TH111GFCI-NP (120 VAC)
120 VAC, 50/60 Hz
16.7 A maximum (resistive only)
2000 watts @ 120 VAC
Class A (5 MA TRIP LEVEL)
CSA/C, US
0 to 60 ºC (32 °F to 140 ºF)
5 °C to 40 ºC (40 °F to 104 ºF)
28 °C (82 °F)
18 °C (64 °F)
-20 °C to 50 ºC (-4 °F to 120 ºF)
1 ºC (2 °F)
± 0.5 ºC (1 °F) (2000 W)
WARRANTY
for outside area, Monday to Friday between
09/03/01
buttons. Keep
, you can still use
720-111715-B 2/2
Advertisement
