Summary of Contents for Omega CCT-05 Series
- Page 1 User’ s Guide ® http://www.omega.com e-mail: info@omega.com CCT-05 Frequency Input Signal Conditioners M2216/1201...
- Page 2 OMEGAnet http://www.omega.com USA: One Omega Drive, Box 4047 ISO 9001 Certified Stamford, CT 06907-0047 Tel: (203) 359-1660 e-mail: info@omega.com Canada: 976 Bergar Laval (Quebec) H7L 5A1 Tel: (514) 856-6928 e-mail: canada@omega.com For immediate technical or application assistance: USA and Canada: Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA Customer Service: 1-800-622-2378 / 1-800-622-BEST Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN...
-
Page 3: Table Of Contents
TABLE OF CONTENTS Open the Housing ......3 Internal Overview ......3 Power Supply module MA . -
Page 4: Open The Housing
OPEN THE HOUSING PROCEDURE 1. Insert a screwdriver or similar tool in the points marked 2. Turn the screwdriver until the case walls begin to separate towards two side lugs , are free. 3. Grab the Signal Conditioner body, at the points marked ‚... -
Page 5: Power Supply Module Ma
POWER SUPPLY RECOMENDED WIRING The power supply must be connected to terminals 1 and 7. The characteristics of the power supply are shown on the side label. WARNING.- If the power supply is dc voltage, be careful with the polarity indicated for each terminal. -
Page 6: Signal Output Module Ms
SIGNAL OUTPUT module MS The signal conditioner provides two different analog output signals, both proportional to the signal input. Output in Current : 4 to 20 mA, terminals 9 - 10 Output in Voltage : 0 to 10 Vdc, terminals 11 - 12 Do not use both outputs simultaneously. -
Page 7: Signal Input, Module Me Overview
SIGNAL INPUT, module ME OVERVIEW This module together with the "MP" input board, performs the signal input conditioner (see Fig. 2). This module contains the trimmers and jumpers for the amplifier gain and the low level output (offset). The signal input connections are made at Terminals 3, 4, 5 and 6. Each signal type use some of these terminals. -
Page 8: Sensor Type Selection
SENSOR TYPE SELECTION This signal conditioner can connect to standard sensors such as PNP, NPN, Namur or ac signals. See the Connections Section. The signal conditioner provides two excitation voltages for the sensors, 24 Vdc for PNP or NPN sensors and 8.2 Vdc for NAMUR sensors. Table 4 indicates which jumpers must be selected for each type of sensor. -
Page 9: Signal Input Range Selection
SIGNAL INPUT RANGE SELECTION Set the jumpers to the position indicated in Table 5 for each range. The jumpers are located on the "MP" input board. If the signal input is modified, follow the adjustment and calibration procedure. TABLE 5 FREQUENCY RANGE (Selector B) 0 to... -
Page 10: Connections
Sensors PNP or NPN POWER SUPPLY INPUT / ENTRADA The side label, shows the type and value of the power supply. OUTPUTS / SALIDAS 9 10 11 12 SIGNAL OUTPUT Current SIGNAL OUTPUT Current CONNECTIONS FIG.9 Sensor NAMUR POWER SUPPLY The side label, shows the type and value of the... -
Page 11: Mechanical Specifications
MECHANICAL DIMENSIONS 36 mm (1.417") TECHNICAL DATA WEIGHT ....270 g. HOUSING BASE ... . Polycarbonate, RAL 7032, UL 94 V-1 light grey, IP-40 TERMINAL HOUSING, COVER AND BLIND PLUGS . -
Page 12: Notes
NOTES... - Page 13 MADE U U SA WARRANTY/DISCLAIMER OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 13 months from date of purchase. OMEGA Warranty adds an additional one (1) month grace period to the normal one (1) year product warranty to cover handling and shipping time.
- Page 14 Where Do I Find Everything I Need for Process Measurement and Control? OMEGA…Of Course! TEMPERATURE Thermocouple, RTD & Thermistor Probes, Connectors, Panels & Assemblies Wire: Thermocouple, RTD & Thermistor Calibrators & Ice Point References Recorders, Controllers & Process Monitors Infrared Pyrometers PRESSURE, STRAIN AND FORCE Transducers &...