Page 1 EOS 6D (WG) EOS 6D (N) ENGLISH The EOS 6D (N) does not have the Wi-Fi and GPS functions. INSTRUCTION MANUAL...
Page 2: Introduction
AF, approx. 4.5 fps continuous shooting, Live View shooting, Full High- Definition (Full HD) movie shooting, Wi-Fi*, and GPS*. * The EOS 6D (N) does not have the Wi-Fi and GPS functions. Before Starting to Shoot, Be Sure to Read the Following To avoid botched pictures and accidents, first read the “Safety...
Page 3: Compatible Cards
Compatible Cards The camera can use the following cards regardless of capacity: • SD memory cards • SDHC memory cards* • SDXC memory cards* * UHS-I cards compatible. Cards that Can Record Movies When shooting movies, use a large-capacity card with a fast reading/ writing speed as shown in the table.
Page 4: Item Check List
Item Check List Before starting, check that all the following items have been included with your camera. If anything is missing, contact your dealer. Battery Pack Battery Charger Camera LP-E6 LC-E6/LC-E6E* (with protective cover) (with body cap) Interface Cable IFC-200U Stereo AV Cable Wide Strap AVC-DC400ST...
Page 5: Instruction Manuals And Disks
Pocket Guide Explains the camera’s basic function settings and basic shooting/playback instructions. Wi-Fi/GPS Cautions* * Not provided with the EOS 6D (N). EOS Camera Instruction Manuals Disk (DVD-ROM) EOS Camera Instruction Manuals Disk XXX Contains the following PDF manuals: CEL-XXX XXX •...
Page 6: Conventions Used In This Manual
Conventions Used in this Manual Icons in this Manual < > : Indicates the Main Dial. < > : Indicates the Quick Control Dial. <9> <V> : Indicates the Multi-controller and the push direction. <0> : Indicates the Setting button. : Indicates that the corresponding function remains active for 4 sec., 6 sec., 10 sec., or 16 sec.
Page 7: Table Of Contents
Chapters For first-time DSLR users, Chapters 1 and 2 explain the camera’s basic operations and shooting procedures. Introduction Getting Started Basic Shooting Setting the AF and Drive Modes Image Settings Advanced Operations Flash Photography Shooting with the LCD Monitor (Live View Shooting) Shooting Movies Image Playback Post-Processing Images...
Page 8 Contents Introduction Compatible Cards................3 Item Check List................. 4 Instruction Manuals and Disks ............5 Conventions Used in this Manual............. 6 Chapters................... 7 Index to Features ................14 Handling Precautions ..............16 Quick Start Guide ................18 Nomenclature ................. 20 Getting Started Charging the Battery ..............
Page 9 Contents Basic Shooting A Fully Automatic Shooting (Scene Intelligent Auto) ....66 A Full Auto Techniques (Scene Intelligent Auto)......69 C Creative Auto Shooting.............71 8: Special Scene Mode .............74 2 Shooting Portraits ..............75 3 Shooting Landscapes ............... 76 4 Shooting Close-ups..............77 5 Shooting Moving Subjects ............
Page 10 Contents Setting the White Balance ............120 O Custom White Balance ............121 P Setting the Color Temperature ........... 122 White Balance Correction............. 123 Auto Correction of Brightness and Contrast......... 125 Noise Reduction Settings ............. 126 Highlight Tone Priority ..............130 Lens Peripheral Illumination / Chromatic Aberration Correction ..
Page 11 Contents Flash Photography D Flash Photography ..............170 Setting the Flash ................172 Shooting with the LCD Monitor (Live View Shooting) A Shooting with the LCD Monitor ..........180 Shooting Function Settings ............185 Menu Function Settings ..............187 Using AF to Focus (AF Method) ........... 192 Focusing Manually ................
Page 12 Contents X Editing a Movie’s First and Last Scenes ......... 255 Slide Show (Auto Playback) ............257 Viewing the Images on TV............261 K Protecting Images ..............265 L Erasing Images................ 267 Changing Image Playback Settings ..........269 Adjusting the LCD Monitor Brightness ........269 Auto Rotation of Vertical Images ..........
Page 13 Contents C.Fn I: Exposure ............... 304 C.Fn II: Autofocus ..............307 C.Fn III: Operation/Others ............311 8: AF Microadjustment ...............314 8: Custom Controls ..............320 Registering My Menu ..............327 w Register Custom Shooting Modes ..........328 Reference B Button Functions ..............332 Checking the Battery Information..........
Page 14: Index To Features
Index to Features Power Charging the battery p.28 AF operation p.92 Battery check p.35 AF point selection p.94 Battery information check p.334 AF Microadjustment p.314 Household power outlet p.338 Manual focusing p.97 Auto power off p.55 Metering Card Metering mode p.149 p.53 Format...
Page 15 Append Dust Delete Data p.281 Movie recording size p.216 Wi-Fi/GPS* Sound recording p.218 Separate booklet Wi-Fi Time code p.220 Separate booklet GPS Still photo shooting p.213 * The EOS 6D (N) does not have the Video snapshot p.225 Wi-Fi and GPS functions.
Page 16: Handling Precautions
If you have not used the camera for some time or if there is an important shoot such as a foreign trip coming up, have the camera checked by your Canon dealer or check the camera yourself and make sure it is working properly.
Page 17 Handling Precautions LCD Panel and LCD Monitor Although the LCD monitor is manufactured with very high precision  technology with over 99.99% effective pixels, there may be a few dead pixels displaying only black or red, etc. among the remaining 0.01% or less pixels. Dead pixels are not a malfunction.
Page 18: Quick Start Guide
Quick Start Guide Insert the battery (p.30) To charge the battery, see page 28.  Insert a card (p.31) With the card’s label facing  toward the back of the camera, insert it into the card slot. Attach the lens (p.39) Align it with the red dot.
Page 19 Quick Start Guide While holding down the center of the Mode Dial, set it to <A> (Scene Intelligent Auto) (p.66) All the necessary camera settings  will be set automatically. Focus the subject (p.44) Look through the viewfinder and  aim the viewfinder center over the subject.
Page 20: Nomenclature
Nomenclature LCD panel (p.22) <R> Drive mode selection button (p.98) <f> AF operation selection button (p.92) ISO speed setting button (p.106) <q> Metering mode Lens mount index (p.39) selection button (p.149) Flash-sync contacts LCD panel Hot shoe (p.170) illumination button (p.48) <6>...
Page 21 Nomenclature AF start button <V> Focal plane mark (p.44, 181, 211) <A/k> Live View shooting/ Movie shooting switch (p.179/203) <A> AE lock/ <0> Start/Stop button (p.180, 204) FE lock button (p.153/170) Dioptric adjustment knob (p.43) <S> AF point selection button (p.94) Eyecup (p.166) Viewfinder eyepiece...
Page 22: Lcd Panel
Nomenclature LCD Panel Drive mode (p.98) <A> Highlight tone priority (p.130) Single shooting Continuous shooting <g> ISO speed (p.106) Silent single shooting ISO speed (p.106) Silent continuous shooting Possible shots Self-timer: 10 sec./ Self-timer countdown Remote control Bulb exposure time Self-timer: 2 sec./ Error No.
Page 23: Viewfinder Information
Nomenclature Viewfinder Information AF points (p.94) (Superimposed display) Focusing screen (p.312) Spot metering circle (p.150) <g> ISO speed (p.106) <o> Focus confirmation light (p.67) <h> Warning symbol (p.313) Max. burst (p.105) <z> Battery check (p.35) Number of remaining multiple exposures (p.160) <A>...
Page 24: Shooting Mode
Nomenclature Mode Dial Turn the Mode Dial while holding down the Mode Dial center (Mode Dial lock release button). Creative Zone These modes give you more control for shooting various subjects. d : Program AE (p.142) s : Shutter-priority AE (p.144) f : Aperture-priority AE (p.146) a : Manual exposure (p.148) F : Bulb (p.154)
Page 25 Nomenclature Lens EF24-105mm f/4L IS USM Focus mode switch (p.39) Distance scale Infrared index Hood mount (p.41) Zoom ring (p.40) Zoom position index (p.40) φ77mm filter thread (front of lens) Focusing ring (p.97, 199) Contacts (p.17) Image Stabilizer switch (p.42) Lens mount index (p.39)
Page 26 Nomenclature Battery Charger LC-E6 Charger for Battery Pack LP-E6/LP-E6N (p.28). Power plug Battery pack slot Charge lamp IMPORTANT SAFETY INSTRUCTIONS-SAVE THESE INSTRUCTIONS. DANGER-TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS. For connection to a supply not in the U.S.A., use an attachment plug adapter of the proper configuration for the power outlet, if needed.
Page 27: Getting Started
Getting Started This chapter explains preparatory steps before you start shooting and basic camera operations. Attaching the Strap Pass the end of the strap through the camera’s strap mount eyelet from the bottom. Then pass it through the strap’s buckle as shown in the illustration.
Page 28: Charging The Battery
Charging the Battery Remove the protective cover. Detach the protective cover provided  with the battery. Attach the battery. As shown in the illustration, attach the  battery securely to the charger. To detach the battery, follow the  above procedure in reverse. Recharge the battery.
Page 29 Charging the Battery Tips for Using the Battery and Charger Upon purchase, the battery is not fully charged.  Recharge the battery before using. Recharge the battery on the day before or on the day it is to be used. ...
Page 30: Installing And Removing The Battery
Installing and Removing the Battery Load a fully charged Battery Pack LP-E6 (or LP-E6N) into the camera. Installing the Battery Open the cover. Slide the lever as shown by the  arrows and open the cover. Insert the battery. Insert the end with the battery ...
Page 31: Installing And Removing The Card
Installing and Removing the Card The camera can use an SD, SDHC, or SDXC memory card. UHS-I Speed Class SDHC and SDXC memory cards can also be used. The captured images are recorded onto the card. Make sure the card’s write-protect switch is set upward to enable writing/erasing.
Page 32: Release Shutter Without Card
Installing and Removing the Card The number of possible shots depends on the remaining capacity of the  card, image-recording quality, ISO speed, etc. Setting [z1: Release shutter without card] to [Disable] will prevent  you from forgetting to insert a card (p.346). Removing the Card Open the cover.
Page 33 Installing and Removing the Card When the access lamp is lit or blinking, it indicates that images are  being written to or read by the card, being erased, or data is being transferred. Do not open the card slot cover during this time. Also, never do any of the following while the access lamp is lit or blinking.
Page 34: Turning On The Power
Turning on the Power If you turn on the power switch and the Date/Time/Zone setting screen appears, see page 36 to set the Date/Time/Zone. <1> : The camera turns on. <2> : The camera is turned off and does not operate. Set to this position when not using the camera.
Page 35: Checking The Battery Level
Turning on the Power z Checking the Battery Level When the power switch is set to <1>, the battery level will be indicated in one of six levels. A blinking battery icon (b) indicates that the battery will be exhausted soon. Icon Level (%) 100 - 70 69 - 50 49 - 20 19 - 10 9 - 1...
Page 36: Setting The Date, Time, And Zone
Setting the Date, Time, and Zone When you turn on the power for the first time or if the date/time/zone have been reset, the Date/Time/Zone setting screens will appear. Follow the steps below to set the time zone first. If you set the camera to the correct time zone for where you currently live, when you travel to another time zone you can simply set the camera to the correct time zone for your destination to update the camera’s date/time...
Page 37 3 Setting the Date, Time, and Zone Set the date and time. Press the key to select the  number. Press <0> so <r> is displayed.  Press the <V> key to set the  number, then press <0>. (Returns to <s>.) Set the Daylight Saving Time.
Page 38: Selecting The Interface Language
Selecting the Interface Language Display the menu screen. Press the <M> button to display  the menu screen. Under the [52] tab, select [LanguageK]. Press the key to select the  [52] tab. Press the <V> key to select ...
Page 39: Attaching And Detaching A Lens
Attaching and Detaching a Lens The camera is compatible with all Canon EF lenses. The camera cannot be used with EF-S and EF-M lenses. Remove the caps. Remove the rear lens cap and the  body cap by turning them as shown by the arrows.
Page 40: Zoom
Attaching and Detaching a Lens About Zooming To zoom, turn the zoom ring on the lens with your fingers. If you want to zoom, do it before focusing. Turning the zoom ring after achieving focus may throw off the focus slightly. Detaching the Lens While pressing the lens release button, turn the lens as shown by...
Page 41 Attaching and Detaching a Lens Attaching a Lens Hood A lens hood can block unwanted light and protect the front of the lens from rain, snow, dust, etc. Before storing the lens in a bag, etc., you can attach the hood in reverse. If the Lens Hood and Lens Have a Mount Index Align the red dots on the hood and lens edges, and turn the...
Page 42: About The Lens Image Stabilizer
About the Lens Image Stabilizer When you use the IS lens’ built-in Image Stabilizer, camera shake is corrected to obtain a sharper shot. The procedure explained here is based on the EF24-105mm f/4L IS USM lens as an example. * IS stands for Image Stabilizer. Set the Image Stabilizer switch to <1>.
Page 43: Basic Operation
Basic Operation Adjusting the Viewfinder Clarity Turn the dioptric adjustment knob. Turn the knob left or right so that the  AF points in the viewfinder look sharp. If the knob is difficult to turn, remove  the eyecup (p.166). If the camera’s dioptric adjustment still cannot provide a sharp viewfinder image, using E-series Dioptric Adjustment Lenses (10 types, sold separately) is recommended.
Page 44: Shutter Button
Basic Operation Shutter Button The shutter button has two steps. You can press the shutter button halfway. Then you can further press the shutter button completely. Pressing halfway This activates autofocusing and the automatic exposure system that sets the shutter speed and aperture. The exposure setting (shutter speed and aperture) is displayed in the viewfinder and on the LCD panel (0).
Page 45: Mode Dial
Basic Operation Mode Dial Turn the dial while holding down the lock release button at the center of the dial. Main Dial After pressing a button, turn the <6> dial. When you press a button such as <f> <R> , the respective function remains selected for the duration of the timer (9).
Page 46 Basic Operation Quick Control Dial After pressing a button, turn the <5> dial. When you press a button such as <f> <R> , the respective function remains selected for the duration of the timer (9). During this time, you can turn the <5>...
Page 47 Basic Operation Multi-controller The Multi-controller <9> has eight keys which tilt in the directions shown by the arrows. Use the eight keys to select the AF  point, correct the white balance, move the AF point or magnifying frame during Live View shooting, scroll around magnified images during playback, etc.
Page 48: Lcd Panel Illumination
Basic Operation U LCD Panel Illumination Turn on (9)/off the LCD panel illumination by pressing the button. During a bulb exposure, pressing the shutter button completely will turn off the LCD panel illumination. Displaying Shooting Function Settings After you press the button a number of times, the shooting function settings will be displayed.
Page 49: Q Quick Control For Shooting Functions
Q Quick Control for Shooting Functions You can directly select and set the shooting functions displayed on the LCD monitor. This is called the Quick Control screen. Press the <Q> button. The Quick Control screen will appear (7). Set the desired function. Press the <V>...
Page 50 Q Quick Control for Shooting Functions Sample Quick Control Screen Aperture (p.146) Flash exposure compensation (p.170) Shutter speed (p.144) AE lock* (p.153) Shooting mode* (p.24) Highlight tone priority* (p.130) Exposure ISO speed (p.106) compensation/AEB setting (p.151, 152) Wi-Fi function* Picture Style (p.112) Custom Controls (p.320) AF operation (p.92)
Page 51: Menu Operations
Menu Operations You can set various settings with the menus such as the image- recording quality, date/time, etc. While looking at the LCD monitor, use the <M> button, <V> keys, and < > button on the camera back. <M> button <0>...
Page 52 3 Menu Operations Menu Setting Procedure Display the menu screen. Press the <M> button to display  the menu screen. Select a tab. Press the key to select a  menu tab. For example, the [z4] tab refers to ...
Page 53: Before You Start
Before You Start 3 Formatting the Card If the card is new or was previously formatted by another camera or computer, format the card with the camera. When the card is formatted, all images and data in the card will be erased.
Page 54 Before You Start Execute [Format card] in the following cases: The card is new.  The card was formatted by a different camera or a computer.  The card is full with images or data.  A card-related error is displayed (p.370). ...
Page 55: Setting The Power-Off Time/Auto Power Off
Before You Start 3 Setting the Power-off Time/Auto Power Off To save battery power, the camera turns off automatically after a set time of idle operation elapses. If you do not want the camera to turn off automatically, set this to [Disable]. After the power turns off, you can turn on the camera again by pressing the shutter button or other buttons.
Page 56: Turning The Lcd Monitor Off/On
Before You Start 3 Turning the LCD Monitor Off/On The shooting settings display (p.48) can be set to remain on even when you press the shutter button halfway. Under the [52] tab, select [LCD off/on btn], then press <0>. The available settings are described below.
Page 57: Shooting Settings
Before You Start Shooting Settings AF operation One-Shot AF u (Single Drive mode shooting) AF point Automatic selection selection Exposure Canceled compensation/AEB q (Evaluative Metering mode metering) Flash exposure 0 (Zero) compensation ISO speed Auto Multiple exposure Disable Minimum limit: 100 ISO speed range Maximum limit: 25600 HDR Mode...
Page 58 Before You Start Image-recording Settings Camera Settings Image quality Auto power off 1 min. Picture Style Auto Beep Enable Auto Lighting Release shutter Standard Enable Optimizer without card Image review 2 sec. Peripheral Enable/ illumination Correction Highlight alert Disable correction data retained AF point display Disable...
Page 59: Movie Shooting Settings
Before You Start Live View Shooting Settings Movie Shooting Settings AF method FlexiZone - Single Live View Enable shooting Silent LV Mode 1 shooting AF method FlexiZone - Single Grid display Metering timer 16 sec. Aspect ratio Grid display Exposure Movie recording Enable 1920x1080/IPB...
Page 60: Q Displaying The Electronic Level
Q Displaying the Electronic Level You can display the electronic level on the LCD monitor, and in the viewfinder or on the LCD panel to help correct camera tilt. Note that you can check only the horizontal tilt and not the forward/backward tilt. Displaying the Electronic Level on the LCD Monitor Press the ...
Page 61: Electronic Level
Q Displaying the Electronic Level Displaying the Electronic Level in the Viewfinder The electronic level display in the viewfinder and on the LCD panel uses the exposure level indicator. Note that the electronic level is only displayed when shooting in horizontal orientation. It is not displayed in vertical orientation.
Page 62 Q Displaying the Electronic Level Display the electronic level. Press the Depth-of-field preview  button. The horizontal tilt up to ±9° in 1° increments will be displayed in the viewfinder and on the LCD panel using the exposure level indicator. Pressing the shutter button halfway ...
Page 63: Feature Guide And Help
Feature Guide and Help While you set some function, the feature’s description can be displayed. Feature Guide The Feature guide displays a simple description of the respective shooting mode, function or option. It appears when you change the shooting mode or set a shooting function, Live View shooting, Movie shooting, or Quick Control for playback.
Page 64: Help
Feature Guide and Help Help When [zHelp] is displayed at the bottom of the menu screen, pressing the button displays the function’s description (Help). If the Help fills more than one screen, a scroll bar will appear on the right edge.
Page 65: Basic Shooting
Basic Shooting This chapter explains how to use the Basic Zone modes on the Mode Dial for best results. With Basic Zone modes, all you do is point and shoot while the camera sets everything automatically (p.83, 342). Also, to prevent botched pictures due to mistaken operations, the main shooting function settings cannot be changed.
Page 66: A Fully Automatic Shooting (Scene Intelligent Auto)
A Fully Automatic Shooting (Scene Intelligent Auto) <A> is a fully automatic mode. The camera analyzes the scene and sets the optimum settings automatically. It also adjusts focus automatically by detecting whether the subject is still or moving (p.69). Set the Mode Dial to <A>. Turn the Mode Dial while holding ...
Page 67: Lcd Monitor
A Fully Automatic Shooting (Scene Intelligent Auto) Take the picture. Press the shutter button completely to  take the picture. The captured image will be displayed for 2 sec. on the LCD monitor. The <A> mode makes the colors look more impressive in nature, outdoor, and sunset scenes.
Page 68  Since it is too dark, taking the picture may result in a blurred subject due to camera shake. Using a tripod or a Canon EX-series Speedlite (p.170) (sold separately) is recommended. When the external flash was used, the bottom part of the ...
Page 69: A Full Auto Techniques (Scene Intelligent Auto)
A Full Auto Techniques (Scene Intelligent Auto) Recomposing the Shot Depending on the scene, position the subject toward the left or right to create a balanced background and good perspective. In the <A> mode, while you press the shutter button halfway to focus a still subject, the focus will be locked.
Page 70: Lcd Monitor
A Full Auto Techniques (Scene Intelligent Auto) A Live View Shooting You can shoot while viewing the image on the LCD monitor. This is called “Live View shooting”. For details, see page 179. Set the Live View shooting/Movie shooting switch to <A>. Display the Live View image on the LCD monitor.
Page 71: C Creative Auto Shooting
C Creative Auto Shooting In the <C> mode, you can easily change the depth of field and drive mode. You can also choose the ambience you want to convey in your images. The default settings are the same as the <A> mode. * CA stands for Creative Auto.
Page 72 C Creative Auto Shooting Shutter speed Aperture ISO speed Battery check Possible shots Image-recording quality Pressing the <Q> button enables you to set the following: (1) Ambience-based shots You can choose the ambience you want to convey in your images. Turn the <6>...
Page 73 C Creative Auto Shooting (3) Drive mode: Press the key to select the desired drive mode. You can also select the drive mode by turning the <6> or <5> dial, or pressing <0> to select it from a list. ...
Page 74: 8: Special Scene Mode
8: Special Scene Mode When you set a shooting mode suiting the scene, the camera sets the optimum settings automatically. Set the Mode Dial to <8>. Press the <Q> button. The Quick Control screen will appear. Select the shooting mode. Press the <V>...
Page 75: Shooting Portraits
2 Shooting Portraits The <2> (Portrait) mode blurs the background to make the human subject stand out. It also makes skin tones and the hair look softer. Shooting Tips The further the distance between the subject and background,  the better. The further the distance between the subject and background, the more blurred the background will look.
Page 76: Shooting Landscapes
3 Shooting Landscapes Use the <3> (Landscape) mode for wide scenery or to have everything in focus from near to far. For vivid blues and greens, and very sharp and crisp images. Shooting Tips With a zoom lens, use the wide-angle end. ...
Page 77: Shooting Close-Ups
4 Shooting Close-ups When you want to photograph flowers or small things up close, use the <4> (Close-up) mode. To make small things appear much larger, use a macro lens (sold separately). Shooting Tips Use a simple background.  A simple background makes the flower, etc., stand out better. Move as close as possible to the subject.
Page 78: Shooting Moving Subjects
5 Shooting Moving Subjects To photograph a moving subject, whether it is a child running or a moving vehicle, use the <5> (Sports) mode. Shooting Tips Use a telephoto lens.  Using a telephoto lens is recommended so you can shoot from afar. Use the center AF point to focus.
Page 79: Shooting Night Portraits (With A Tripod)
6 Shooting Night Portraits (With a Tripod) To shoot people at night and obtain a natural-looking night scene in the background, use the <6> (Night Portrait) mode. Flash is required. Using a tripod is also recommended. Shooting Tips Use a wide-angle lens, Speedlite, and a tripod. ...
Page 80: F Shooting Night Scenes (Handheld)
F Shooting Night Scenes (Handheld) Normally, a tripod is necessary to steady your camera when shooting a night scene. However, with the <F> (Handheld Night Scene) mode, you can shoot night scenes while handholding the camera. In this mode, four shots are taken continuously for each picture, and a resulting bright image with reduced camera shake is recorded.
Page 81: G Shooting Backlit Scenes
G Shooting Backlit Scenes When shooting a scene having both bright and dark areas, use the <G> (HDR Backlight Control) mode. When you take a picture, three continuous shots are taken at different exposures, and the resulting image with the least loss of shadow detail due to backlighting and widest tonal range is recorded.
Page 82 Cautions for <F> (Handheld Night Scene) During Live View shooting, it may be difficult to focus dots of light such as  in a night scene. In such a case, you should set the AF method to [Quick mode] and shoot. If it is still difficult to focus, set the lens’ focus mode switch to [MF] and focus manually.
Page 83: Q Quick Control
Q Quick Control In Basic Zone modes when the shooting Example: Portrait mode function settings screen is displayed, you can press the <Q> button to display the Quick Control screen. The table below indicates the functions that can be set with the Quick Control screen in each Basic Zone mode.
Page 84: Shoot By Ambience Selection
Shoot by Ambience Selection Except in the <A> and <G> Basic Zone modes, you can select the ambience for shooting. Ambience Ambience Effect 2 3 4 5 6 F k k k k k k k Standard setting No setting k k k k k k k Vivid Low / Standard / Strong...
Page 85: Lcd Monitor
Shoot by Ambience Selection Press the key to select the  desired ambience. The LCD monitor will display how the image will look with the selected ambience. Set the ambience effect. Press the <V> key to select the  effect bar so that [Effect] appears at the bottom.
Page 86 Shoot by Ambience Selection Ambience Settings Standard setting Standard image characteristics for the respective shooting mode. Note that <2> has image characteristics geared for portraits and <3> is geared for landscapes. Each ambience is a modification of the respective shooting mode’s image characteristics. Vivid The subject will look sharp and vivid.
Page 87: Shoot By Lighting Or Scene Type
Shoot by Lighting or Scene Type In the <2>, <3>, <4>, and <5> Basic Zone modes, you can shoot while the settings match the lighting or scene type. Normally, [ Default setting] is adequate, but if the settings match the lighting condition or scene, the picture will look more accurate to your eye.
Page 88 Shoot by Lighting or Scene Type On the Quick Control screen, select the lighting or scene type. Press the <Q> button (7).  Press the <V> key to select [  Default setting]. [Light/scene- based shots] will appear on the screen.
Page 89 Shoot by Lighting or Scene Type Lighting or Scene Type Settings Default setting Default setting suited for most subjects. Daylight For subjects under sunlight. Gives more natural-looking blue skies and greenery and reproduces light-colored flowers better. Shade For subjects in the shade. Suitable for skin tones, which may look too bluish, and for light-colored flowers.
Page 91: Setting The Af And Drive Modes
Setting the AF and Drive Modes The viewfinder has 11 AF points. By selecting the optimum AF point, you can compose the picture as desired while autofocusing. You can also select the AF operation and drive mode that best match the shooting conditions and subject. The M icon at the upper right of the page title indicates that ...
Page 92: F: Selecting The Af Operation
f: Selecting the AF OperationN You can select the AF operation characteristics to suit the shooting conditions or subject. In Basic Zone modes, the optimum AF operation is set automatically for the respective shooting mode. Set the lens focus mode switch to <AF>.
Page 93: Ai Servo Af For Moving Subjects
f: Selecting the AF OperationN If focus cannot be achieved, the focus confirmation light <o> in the  viewfinder will blink. If this occurs, the picture cannot be taken even if the shutter button is pressed completely. Recompose the shot and try to focus again, or see “When Autofocus Fails”...
Page 94: S Selecting Af Points
S Selecting AF PointsN You can select an AF point for focusing from among eleven AF points. In Basic Zone modes, the AF point will be selected automatically and you cannot select the AF point. Press the <S> button. The selected AF point will be displayed in the viewfinder and on the LCD panel.
Page 95 S Selecting AF PointsN Selecting with the Dials Turn the <6> dial to select an AF  point on the left or right or turn the <5> dial to select an AF point above or below. If all the AF points light up, automatic ...
Page 96: When Autofocus Fails
When Autofocus Fails Autofocus can fail to achieve focus (viewfinder’s focus confirmation light <o> blinks) with certain subjects such as the following: Subjects difficult to focus Very low-contrast subjects  (Example: Blue sky, solid-color walls, etc.) Subjects in very low light ...
Page 97: Mf: Manual Focusing
When Autofocus Fails MF: Manual Focusing Set the lens focus mode switch to <MF>. <4 L> will be displayed on the LCD panel. Focus the subject. Focusing ring Focus by turning the lens focusing  ring until the subject looks sharp in the viewfinder.
Page 98: Selecting The Drive Mode
i Selecting the Drive Mode Single and continuous drive modes are provided. Press the <R> button. Select the drive mode. While looking at the LCD panel, turn  the <6> or <5> dial. u : Single shooting When you press the shutter button completely, only one shot will be taken.
Page 99 i Selecting the Drive Mode If or <M> is set, the time lag from when you press the shutter  button completely until the picture is shot will be longer than with normal single or continuous shooting. When the battery level is low, the continuous shooting speed may ...
Page 100: Using The Self-Timer
j Using the Self-timer Use the self-timer when you want to be in the picture. Press the <R> button. Select the self-timer. While looking at the LCD panel, turn  the <6> or <5> dial to select the self-timer delay. Q : 10-sec.
Page 101: Image Settings
Image Settings This chapter explains image-related function settings: Image-recording quality, ISO speed, Picture Style, white balance, Auto Lighting Optimizer, lens peripheral illumination correction, chromatic aberration correction, and other functions. In Basic Zone modes, only the following can be set as ...
Page 102: Setting The Image-Recording Quality
Setting the Image-Recording Quality You can select the pixel count and the image quality. There are eight JPEG image-recording quality settings: 73, 83, 74, 84, 7a, 8a, b, c. There are three RAW image quality settings: 1, 41, 61 (p.104). Select [Image quality].
Page 103 Standard Picture Style) using an 8 GB card. These figures will vary depending on the subject, card brand, aspect ratio, ISO speed, Picture Style, Custom Functions, and other settings. Figures in parentheses apply to an UHS-I class 8 GB card based on Canon’s  testing standards.
Page 104 3 Setting the Image-Recording Quality If you select both RAW and JPEG, the same image will be recorded  simultaneously to the card in both RAW and JPEG at the image- recording quality that was set. The two images will be recorded with the same file numbers (file extension .JPG for JPEG and .CR2 for RAW).
Page 105: Maximum Burst
3 Setting the Image-Recording Quality Maximum Burst During Continuous Shooting The approximate maximum burst is displayed on the bottom right in the viewfinder and on the shooting function settings screen. If the maximum burst for continuous shooting is 99 or higher, “99” will be displayed.
Page 106: I: Setting The Iso Speed
i: Setting the ISO SpeedN Set the ISO speed (image sensor’s sensitivity to light) to suit the ambient light level. In Basic Zone modes, the ISO speed is set automatically (p.108). Regarding the ISO speed during movie shooting, see pages 206 and 209. Press the ...
Page 107 i: Setting the ISO SpeedN If [z4: Highlight tone priority] is set to [Enable], you cannot select “L”  (equivalent to ISO 50), ISO 100/125/160, “H1” (equivalent to ISO 51200), and “H2” (equivalent to ISO 102400) (p.130). Shooting in high temperatures may result in images that look grainier. ...
Page 108: Iso Auto
i: Setting the ISO SpeedN ISO Auto If the ISO speed is set to “A” (Auto), the actual ISO speed to be set will be displayed when you press the shutter button halfway. As indicated below, the ISO speed will be set automatically to suit the shooting mode.
Page 109 i: Setting the ISO SpeedN 3 Setting the ISO Speed Range You can set the manually-settable ISO speed range (minimum and maximum limits). You can set the minimum limit within L (ISO 50) to H1 (ISO 51200), and the maximum limit within ISO 100 to H2 (ISO 102400).
Page 110 i: Setting the ISO SpeedN 3 Setting the ISO Speed Range for Auto ISO You can set the automatic ISO speed range for Auto ISO within ISO 100 - 25600. You can set the minimum limit within ISO 100 - 12800, and the maximum limit within ISO 200 - 25600 in whole-stop increments.
Page 111 i: Setting the ISO SpeedN 3 Setting the Minimum Shutter Speed for Auto ISO When Auto ISO is set, you can set the minimum shutter speed (1/250 sec. to 1 sec.) so that the automatically-set shutter speed is not too slow.
Page 112: A Selecting A Picture Style
A Selecting a Picture StyleN By selecting a Picture Style, you can obtain image characteristics matching your photographic expression or the subject. In Basic Zone modes, <D> (Auto) is set automatically. Select [Picture Style]. Under the [z4] tab, select [Picture ...
Page 113 A Selecting a Picture StyleN R Landscape For vivid blues and greens, and very sharp and crisp images. Effective for impressive landscapes. S Neutral This Picture Style is for users who prefer to process images with their computer. For natural colors and subdued images. U Faithful This Picture Style is for users who prefer to process images with their computer.
Page 114: About The Symbols
A Selecting a Picture StyleN About the Symbols The symbols of the Picture Style selection screen refer to parameters such as [Sharpness] and [Contrast]. The numerals indicate the parameter settings, such as for [Sharpness] and [Contrast], for each Picture Style. Symbols Sharpness Contrast...
Page 115: A Customizing A Picture Style
A Customizing a Picture StyleN You can customize a Picture Style by adjusting individual parameters such as [Sharpness] and [Contrast]. To see the resulting effects, take test shots. To customize [Monochrome], see page 117. Select [Picture Style]. Under the [z4] tab, select [Picture ...
Page 116 A Customizing a Picture StyleN Parameter Settings and Effects g Sharpness 0: Less sharp outline +7: Sharp outline h Contrast -4: Low contrast +4: High contrast i Saturation -4: Low saturation +4: High saturation j Color tone -4: Reddish skin tone +4: Yellowish skin tone By selecting [Default set.] in step 3, you can revert the respective ...
Page 117 A Customizing a Picture StyleN V Monochrome Adjustment For Monochrome, you can also set [Filter effect] and [Toning effect] in addition to [Sharpness] and [Contrast] explained on the preceding page. kFilter Effect With a filter effect applied to a monochrome image, you can make white clouds or green trees stand out more.
Page 118: A Registering A Picture Style
A Registering a Picture StyleN You can select a base Picture Style such as [Portrait] or [Landscape], adjust its parameters as desired and register it under [User Def. 1], [User Def. 2], or [User Def. 3]. You can create multiple Picture Styles whose parameter settings such as sharpness and contrast are different.
Page 119 A Registering a Picture StyleN Select a parameter. Select a parameter such as  [Sharpness], then press <0>. Set the parameter. Press the key to adjust the  parameter as desired, then press <0>. For details, see “Customizing a Picture Style”...
Page 120: Setting The White Balance
Setting the White BalanceN White balance (WB) is for making the white areas look white. Normally, the <Q> (Auto) setting will obtain the correct white balance. If natural- looking colors cannot be obtained with <Q>, you can select the white balance to match the light source or set it manually by shooting a white object.
Page 121: O Custom White Balance
3 Setting the White BalanceN O Custom White Balance Custom white balance enables you to manually set the white balance for a specific light source for better accuracy. Perform this procedure under the actual light source to be used. Photograph a white object. The plain, white object should fill the ...
Page 122: P Setting The Color Temperature
3 Setting the White BalanceN If the exposure obtained in step 1 differs greatly from the standard  exposure, a correct white balance may not be obtained. In step 3, the following images cannot be selected: images captured  while the Picture Style was set to [Monochrome], multiple-exposure images, and images shot with another camera.
Page 123: White Balance Correction
White Balance CorrectionN You can correct the white balance that has been set. This adjustment will have the same effect as using a commercially-available color temperature conversion filter or color compensating filter. Each color can be corrected to one of nine levels. This function is for advanced users who are familiar with using color temperature conversion or color compensating filters.
Page 124: White Balance Auto Bracketing
3 White Balance CorrectionN White Balance Auto Bracketing With just one shot, three images having a different color tone can be recorded simultaneously. Based on the color temperature of the current white balance setting, the image will be bracketed with a blue/amber bias or magenta/green bias.
Page 125: Auto Correction Of Brightness And Contrast
Auto Correction of Brightness and ContrastN If the image comes out dark or the contrast is low, the brightness and contrast can be corrected automatically. This function is called Auto Lighting Optimizer. The default setting is [Standard]. With JPEG images, the correction is applied when the image is captured. In Basic Zone modes, [Standard] is set automatically.
Page 126: Noise Reduction Settings
Noise Reduction SettingsN High ISO Speed Noise Reduction This function reduces the noise generated in the image. Although noise reduction is applied at all ISO speeds, it is particularly effective at high ISO speeds. At low ISO speeds, the noise in the darker parts of the image (shadow areas) is further reduced.
Page 127 3 Noise Reduction SettingsN About [Multi Shot Noise Reduction] The following functions cannot be set: AEB, WB bracketing, [z4: Long  exp. noise reduction], [z4: HDR Mode], [z4: Multiple exposure], and RAW image. If any of these has already been set, [Multi Shot Noise Reduction] cannot be set.
Page 128 3 Noise Reduction SettingsN Long Exposure Noise Reduction Noise reduction is possible with images exposed for 1 sec. or longer. Select [Long exp. noise reduction]. Under the [z4] tab, select [Long  exp. noise reduction], then press <0>. Set the desired setting. Select the desired setting, then press ...
Page 129 3 Noise Reduction SettingsN With [Auto] and [Enable], the noise reduction process after the picture is  taken may take the same amount of time as that for the exposure. During noise reduction, shooting is still possible as long as the maximum burst indicator in the viewfinder shows “1”...
Page 130: Highlight Tone Priority
Highlight Tone PriorityN You can minimize overexposed highlight areas. Select [Highlight tone priority]. Under the [z4] tab, select  [Highlight tone priority], then press <0>. Select [Enable]. Select [Enable], then press <0>.  Highlight details are improved. The  dynamic range is expanded from the standard 18% gray to bright highlights.
Page 131: Lens Peripheral Illumination / Chromatic Aberration Correction
Lens Peripheral Illumination / Chromatic Aberration Correction Peripheral light fall-off is a phenomenon that makes the image corners look darker due to the lens characteristics. Color fringing along subject outlines is called chromatic aberration. Both lens aberrations can be corrected. The default settings are [Enable] for both corrections. If [Cannot correct - no data] is displayed, see “About the Lens Correction Data”...
Page 132: Chromatic Aberration Correction
3 Lens Peripheral Illumination / Chromatic Aberration Correction Chromatic Aberration Correction Select the setting. Check that [Correction data  available] is displayed for the attached lens. Select [Chromatic aberration], then  press <0>. Select [Enable], then press <0>.  Take the picture. The image will be recorded with the ...
Page 133 Peripheral illumination correction and chromatic aberration correction  cannot be applied to JPEG images already taken. When using a non-Canon lens, setting the corrections to [Disable] is  recommended, even if [Correction data available] is displayed. If you use the magnified view during Live View shooting, the peripheral ...
Page 134: Creating And Selecting A Folder
Creating and Selecting a Folder You can freely create and select the folder where the captured images are to be saved. This operation is optional since a folder will be created automatically for saving captured images. Creating a Folder Select [Select folder]. Under the [51] tab, select [Select ...
Page 135: Selecting A Folder
3 Creating and Selecting a Folder Selecting a Folder With the folder selection screen  Lowest file number displayed, select a folder and press Number of images in folder <0>. The folder where the captured images will be saved is selected. Subsequent captured images will be ...
Page 136: File Numbering Methods
File Numbering Methods The image files will be numbered from 0001 to 9999 in the order the images are taken, then saved in a folder. You can change how the file number is assigned. The file number will appear on your computer in this format: IMG_0001.JPG.
Page 137: Lcd Monitor
3 File Numbering Methods Auto Reset The file numbering restarts from 0001 each time the card is replaced or a new folder is created. When you replace the card or create a folder, the file numbering restarts from 0001 for the new images saved. This is convenient if you want to organize images according to cards or folders.
Page 138: Setting Copyright Information
Setting Copyright InformationN When you set the copyright information, it will be recorded to the image as Exif information. Select [Copyright information]. Under the [54] tab, select [Copyright  information], then press <0>. Select the option to be set. Select [Enter author’s name] or ...
Page 139 3 Setting Copyright InformationN Checking the Copyright Information When you select [Display copyright info.] in step 2 on the preceding page, you can check the [Author] and [Copyright] information that you entered. Deleting the Copyright Information When you select [Delete copyright information] in step 2 on the preceding page, you can delete the [Author] and [Copyright] information.
Page 140: Setting The Color Space
Setting the Color SpaceN The range of reproducible colors is called the color space. With this camera, you can set the color space for captured images to sRGB or Adobe RGB. For normal shooting, sRGB is recommended. In Basic Zone modes, sRGB is set automatically. Select [Color space].
Page 141: Advanced Operations
Advanced Operations In Creative Zone modes, you can set the shutter speed and/or aperture to set the exposure as desired. By changing the camera settings, you can obtain various results. The M icon at the upper right of the page title indicates that ...
Page 142: D: Program Ae
d: Program AE The camera automatically sets the shutter speed and aperture to suit the subject’s brightness. This is called Program AE. * <d> stands for Program. * AE stands for Auto Exposure. Set the Mode Dial to <d>. Focus the subject. Look through the viewfinder and aim ...
Page 143 d: Program AE If the “30"” shutter speed and the lower f/number  blink, it indicates underexposure. Increase the ISO speed or use flash. If the “4000” shutter speed and the higher f/number  blink, it indicates overexposure. Lower the ISO speed or use an ND filter (sold separately) to reduce the amount of light entering the lens.
Page 144: S: Shutter-Priority Ae
s: Shutter-Priority AE In this mode, you set the shutter speed and the camera automatically sets the aperture to obtain the standard exposure suiting the brightness of the subject. This is called shutter-priority AE. A faster shutter speed can freeze the action or a moving subject. A slower shutter speed can create a blurred effect, giving the impression of motion.
Page 145 s: Shutter-Priority AE If the lower f/number blinks, it indicates underexposure.  Turn the <6> dial to set a slower shutter speed until the aperture stops blinking or set a higher ISO speed. If the higher f/number blinks, it indicates overexposure. ...
Page 146: F: Aperture-Priority Ae
f: Aperture-Priority AE In this mode, you set the desired aperture and the camera sets the shutter speed automatically to obtain the standard exposure suiting the subject brightness. This is called aperture-priority AE. A higher f/number (smaller aperture hole) will make more of the foreground and background fall within acceptable focus.
Page 147: Depth Of Field Preview
f: Aperture-Priority AE If the “30"” shutter speed blinks, it indicates  underexposure. Turn the <6> dial to set a larger aperture (lower f/ number) until the shutter speed blinking stops or set a higher ISO speed. If the “4000” shutter speed blinks, it indicates ...
Page 148: A: Manual Exposure
a: Manual Exposure In this mode, you set both the shutter speed and aperture as desired. To determine the exposure, refer to the exposure level indicator in the viewfinder or use a commercially-available exposure meter. This method is called manual exposure. * <a>...
Page 149: Selecting The Metering Mode
q Selecting the Metering ModeN In [z3: Auto Lighting Optimizer], if the checkmark <X> for [Disabled  in M or B modes] is removed, Auto Lighting Optimizer can be set in the <a> and <F> modes (p.125). When ISO Auto is set, you can press the <A> button to lock the ISO speed. ...
Page 150: Spot Metering
q Selecting the Metering ModeN Spot metering This is for metering a specific spot of the subject or scene. The metering is weighted at the center covering approx. 3.5% of the viewfinder area. Center-weighted average metering The metering is weighted at the center and then averaged for the entire scene.
Page 151: Setting Exposure Compensation
Setting Exposure Compensation N Exposure compensation can brighten (increased exposure) or darken (decreased exposure) the standard exposure set by the camera. Exposure compensation can be set in the d/s/f shooting modes. Although you can set the exposure compensation up to ±5 stops in 1/3- stop increments, the exposure compensation indicator in the viewfinder and on the LCD panel can only display the setting up to ±3 stops.
Page 152: Auto Exposure Bracketing (Aeb)
h Auto Exposure Bracketing (AEB)N By changing the shutter speed or aperture automatically, the camera brackets the exposure up to ±3 stops in 1/3-stop increments for three successive shots. This is called AEB. * AEB stands for Auto Exposure Bracketing. Select [Expo.comp./AEB].
Page 153: A Ae Lock
A AE LockN Use AE lock when the area of focus is to be different from the exposure metering area or when you want to take multiple shots at the same exposure setting. Press the <A> button to lock the exposure, then recompose and take the shot.
Page 154: F: Bulb Exposures
F: Bulb Exposures When bulb is set, the shutter stays open as long as you hold down the shutter button completely, and closes when you let go of the shutter button. This is called bulb exposure. Use bulb exposures for night scenes, fireworks, astronomical objects, and other subjects requiring long exposures.
Page 155: W: Hdr (High Dynamic Range) Shooting
w: HDR (High Dynamic Range) ShootingN You can shoot images preserving a wide tonal range where the highlight and shadow detail would otherwise be lost. HDR shooting is effective for landscape and still-life shots. With HDR shooting, three images of different exposures (standard exposure, underexposure, and overexposure) are captured for each shot and then merged together automatically.
Page 156 w: HDR (High Dynamic Range) ShootingN Set [Continuous HDR]. Select either [1 shot only] or [Every  shot], then press <0>. With [1 shot only], HDR shooting will  be canceled automatically after the shooting ends. With [Every shot], HDR shooting ...
Page 157 w: HDR (High Dynamic Range) ShootingN If you shoot a moving subject, the subject’s movement will leave  afterimages. To prevent camera shake, the ISO speed may be set higher than usual.  HDR shooting is not possible with ISO expansion. (HDR shooting is ...
Page 158: P Multiple Exposures
P Multiple ExposuresN You can shoot two to nine exposures to be merged into one image. If you shoot multiple-exposure images with Live View shooting (p.179), you can see how the single exposures merge while shooting. Select [Multiple exposure]. Under the [z4] tab, select [Multiple ...
Page 159 P Multiple ExposuresN Set [Multi-expos ctrl]. Select the desired multiple-exposure  control method, then press <0>. Additive  The exposure of each single exposure is added cumulatively. Based on the [No. of exposures], set a negative exposure compensation. Refer to the basic guide below to set a negative exposure compensation.
Page 160 P Multiple ExposuresN Set [Continue Mult-exp]. Select either [1 shot only] or  [Continuously], then press <0>. With [1 shot only], multiple-exposure  shooting will be canceled automatically after the shooting ends. With [Continuously], multiple-  exposure shooting continues until the setting in step 2 is set to [Disable].
Page 161 P Multiple ExposuresN Only the merged multiple-exposure image will be saved. The images  taken in steps 6 and 7 for the multiple-exposure image will not be saved. With multiple exposures, the more exposures there are, the more  noticeable the noise, irregular colors, and banding will be. Also, as noise increases with higher ISO speeds, shooting at low ISO speeds is recommended.
Page 162 P Multiple ExposuresN Merging Multiple Exposures with an Image Recorded in the Card You can select an image recorded in the card as the first single exposure. The original of the selected image will remain intact. You can only select 1 images. You cannot select 41/61 or JPEG images.
Page 163 P Multiple ExposuresN You can also select a 1 multiple-exposure image as the first single  exposure. If you select [Deselect img], the selected image will be canceled.  Checking and Deleting Multiple Exposures During Shooting Before you finish shooting the set number of exposures, you can press the <x>...
Page 164 P Multiple ExposuresN Are there any restrictions on the image-recording quality?  All JPEG image-recording quality settings can be selected. If 41 or 61 is set, the merged multiple-exposure will be a 1 image. Image-Recording Quality Setting Merged Multiple-Exposure JPEG JPEG 41/61 1+JPEG...
Page 165: Mirror Lockup
2 Mirror LockupN Although using the self-timer or Remote Switch can prevent camera shake, using mirror lockup to prevent camera vibrations (mirror shock) can also help when you use a super telephoto lens or shoot close ups (macro photography). Set [Mirror lockup] to [Enable]. Under the [z2] tab, select [Mirror lockup], then press <0>.
Page 166: Using The Eyepiece Cover
Using the Eyepiece Cover When you use the self-timer, bulb, or Remote Switch and do not look through the viewfinder, stray light entering the viewfinder can cause the image to look dark. To prevent this, use the eyepiece cover (p.27) attached to the camera strap.
Page 167: F Using A Remote Switch
F Using a Remote Switch You can connect the Remote Switch RS-80N3, Timer Remote Controller TC-80N3 (both sold separately), or any EOS accessory equipped with an N3-type terminal to the camera for shooting (p.354). To operate the accessory, refer to its instruction manual. Open the terminal cover.
Page 168 R Remote Control Shooting Press the <R> button. Select the self-timer. Look at the LCD panel and turn the  <6> dial to select <Q> or <k>. Press the remote controller’s transmit button. Point the remote controller toward the  camera’s remote control sensor and press the transmit button.
Page 169: Flash Photography
Flash Photography This chapter explains how to shoot with an EOS- dedicated, EX-series Speedlite (sold separately) or non- Canon flash unit and how to set flash functions on the camera’s menu screen.
Page 170: D Flash Photography
D Flash Photography EOS-dedicated, EX-series Speedlites An EX-series Speedlite (sold separately) makes flash photography as easy as normal shooting. For detailed instructions, refer to the EX-series Speedlite’s instruction manual. This camera is a Type-A camera that can use all the features of EX-series Speedlites. To set the flash functions and flash Custom Functions with the camera’s menu, see pages 172-177.
Page 171 Cautions for Live View shooting If you use a non-Canon flash unit with Live View shooting, set [A2: Silent LV shoot.] to [Disable] (p.190). The flash will not fire if it is set to [Mode 1] or [Mode 2].
Page 172: Setting The Flash
Setting the FlashN With an EX-series Speedlite having compatible flash function settings, you can use the camera’s menu screen to set the Speedlite’s functions and Custom Functions. Attach the Speedlite to the camera and turn on the Speedlite before starting these settings. For details on the Speedlite’s functions, refer to the Speedlite’s instruction manual.
Page 173 3 Setting the FlashN Flash Synchronization Speed in Av Mode You can set the flash-sync speed for flash photography in the aperture-priority AE (f) mode. : Auto  The flash sync speed is set automatically within a range of 1/180 sec.
Page 174: Flash Function Settings
3 Setting the FlashN Flash Function Settings On the screen, the settable functions and the display will differ depending on the Speedlite, current flash mode, flash Custom Function settings, etc. For details on your Speedlite’s flash functions, refer to the Speedlite’s instruction manual.
Page 175 3 Setting the FlashN Wireless functions  Wireless (multiple) flash shooting is possible with radio or optical transmission. For details on wireless flash, refer to the Speedlite’s instruction manual. Flash zoom (Flash coverage)  With Speedlites having a zooming flash head, you can set the flash coverage.
Page 176: Flash Exposure Compensation
3 Setting the FlashN Flash exposure compensation  The same setting as “Flash exposure compensation” on page 170 can be set. For details, refer to the Speedlite’s instruction manual. Flash exposure bracketing  While the flash output is changed automatically, three shots are taken. For details, refer to the instruction manual of a Speedlite compatible with flash exposure bracketing.
Page 177: Flash Custom Function Settings
3 Setting the FlashN Flash Custom Function Settings For details on the Speedlite’s Custom Functions, refer to the Speedlite’s instruction manual. Select [Flash C.Fn settings]. Select [Flash C.Fn settings], then  press <0>. Set the functions. Press the key to select the ...
Page 179: Shooting With The Lcd Monitor
Shooting with the LCD Monitor (Live View Shooting) You can shoot while viewing the picture on the camera’s LCD monitor. This is called “Live View shooting”. Live View shooting is enabled by setting the Live View shooting/ Movie shooting switch to <A>. Live View shooting is effective for photos of still subjects.
Page 180: A Shooting With The Lcd Monitor
A Shooting with the LCD Monitor Set the Live View shooting/Movie shooting switch to <A>. Display the Live View image. Press the <0> button.  The Live View image will appear on the LCD monitor. The Live View image will closely ...
Page 181: Lcd Monitor
A Shooting with the LCD Monitor Enabling Live View Shooting Set [A1: Live View shoot.] to [Enable]. Number of Possible Shots with Live View Shooting Room Temperature Low Temperature Temperature ( 23°C / 73°F) (0°C / 32°F) Possible shots 220 approx. shots 190 approx.
Page 182: Lcd Monitor
A Shooting with the LCD Monitor About the Information Display Each time you press the button, the information display will change.  AF method Possible shots • d : FlexiZone - Single Maximum burst/Multiple exposures remaining • c : Face detection Live Battery check mode AF point (FlexiZone - Single)
Page 183: Lcd Monitor
A Shooting with the LCD Monitor Scene Icons During Live View shooting in the <A> mode, an icon representing the scene detected by the camera will be displayed and the shooting will be adapted to that scene. For certain scenes or shooting conditions, the icon displayed may not match the actual scene.
Page 184: Lcd Monitor
A Shooting with the LCD Monitor *5: Displayed with any of the lenses below: • EF24mm f/2.8 IS USM • EF28mm f/2.8 IS USM • EF300mm f/2.8L IS II USM • EF400mm f/2.8L IS II USM • EF500mm f/4L IS II USM •...
Page 185: Shooting Function Settings
Shooting Function Settings Q Quick Control If you press the <Q> button while the Live View image is displayed in a Creative Zone mode, you can set any of the following: AF method, drive mode, metering mode, image-recording quality, white balance, Picture Style, and Auto Lighting Optimizer.
Page 186: Lcd Monitor
Shooting Function Settings f / R / i / q / S Settings While the Live View image is displayed, if you press the <f>, <R>, , or <q> button, the setting screen will appear on the LCD monitor and you can turn the <6> or <5> dial to set the respective shooting function.
Page 187: Menu Function Settings
Menu Function Settings [A1] Menu Function settings particular to Live View shooting are explained here. Details of menu items under the [A1] and [A2] tabs are on pages 187-191. In Basic Zone modes, certain items under the [A1] tab will not appear and the [A2] tab will not appear.
Page 188: Aspect Ratio
3 Menu Function Settings Aspect ratioM  The image’s aspect ratio can be set to [3:2], [4:3], [16:9], or [1:1]. The area surrounding the Live View image is masked in black when the following aspect ratios are set: [4:3] [16:9] [1:1]. JPEG images will be saved with the set aspect ratio.
Page 189 3 Menu Function Settings Exposure simulationN  Exposure simulation simulates and displays how the brightness of the actual image (exposure) will look. ･ Enable (g) The displayed image brightness will be close to the actual brightness (exposure) of the resulting image. If you set exposure compensation, the image brightness will change accordingly.
Page 190 If you use flash, silent shooting will not be possible regardless of the  [Silent LV shoot.] setting. When using a non-Canon flash unit, set it to [Disable]. The flash will not  fire if it is set to [Mode 1] or [Mode 2].
Page 191 3 Menu Function Settings Metering timerN  You can change how long the exposure setting is displayed (AE lock time). The Live View shooting will stop with any of the following operations. To resume Live View shooting, press the <0> button again. •...
Page 192: Using Af To Focus (Af Method)
Using AF to Focus (AF Method) Selecting the AF Method The AF methods available are [FlexiZoneAF (Single)], [u Live mode] (face detection, p.193), and [Quick mode] (p.197). If you want to achieve precise focus, set the lens focus mode switch to <MF>, magnify the image, and focus manually (p.199).
Page 193: Lcd Monitor
Using AF to Focus (AF Method) Focus the subject. Aim the AF point over the subject and  press the shutter button halfway. When focus is achieved, the AF point will turn green and the beeper will sound. If focus is not achieved, the AF point will turn orange.
Page 194 Using AF to Focus (AF Method) Focus the subject. Press the shutter button halfway and  the camera will focus the face covered by the frame. When focus is achieved, the AF point will turn green and the beeper will sound.
Page 195 Using AF to Focus (AF Method) FlexiZone - Single and u (Face Detection) Live Mode Notes AF Operation Focusing will take slightly longer.  Even when focus has been achieved, pressing the shutter button  halfway will focus again. The image brightness may change during and after the AF ...
Page 196 EF28mm f/2.8, EF35mm f/2, EF50mm f/1.4 USM, EF50mm f/1.8 II, EF50mm f/2.5 Compact Macro, EF135mm f/2.8 (Softfocus), EF75-300mm f/4-5.6 III, EF75-300mm f/4-5.6 III USM For information on discontinued lenses, refer to your local Canon website.
Page 197: Lcd Monitor
Using AF to Focus (AF Method) Quick Mode: f The dedicated AF sensor is used to focus in One-Shot AF mode (p.92), using the same AF method as with viewfinder shooting. Although you can focus the target area quickly, the Live View image will be interrupted momentarily during the AF operation.
Page 198 Using AF to Focus (AF Method) Focus the subject. Aim the AF point over the subject and  press the shutter button halfway. The Live View image will turn off, the reflex mirror will go back down, and AF will be executed. (No picture is taken.) When focus is achieved, the beeper will sound and the Live View image...
Page 199: Focusing Manually
Focusing Manually You can magnify the image and focus precisely with manual focus. Set the lens focus mode switch to <MF>. Turn the lens focusing ring to focus  roughly. Display the magnifying frame. Press the button.  Magnifying frame Move the magnifying frame.
Page 200 Focusing Manually Focus manually. While looking at the magnified image,  turn the lens focusing ring to focus. After achieving focus, press the  button to return to the normal view. Take the picture. Check the focus and exposure, then ...
Page 201 Live View Shooting Cautions Image Quality When you shoot at high ISO speeds, noise (such as dots of light and  banding) may become noticeable. Shooting in high temperatures may cause noise and irregular colors in  the image. If Live View shooting is used continuously for a long period, the camera’s ...
Page 202: Lcd Monitor
Live View Shooting Cautions Live View Image Under low- or bright-light conditions, the Live View image may not reflect  the brightness of the captured image. If the light source (illumination) within the image changes, the screen  may flicker. If this happens, exit Live View shooting and resume shooting under the actual light source.
Page 203: Shooting Movies
Shooting Movies Movie shooting is enabled by setting the Live View shooting/ Movie shooting switch to <k>. The movie recording format will be MOV. For cards which can record movies, see page 3.  Under the [53] tab, if you set [Wi-Fi] to [Enable], you cannot shoot movies.
Page 204 k Shooting Movies Autoexposure Shooting When the shooting mode is set to other than <a>, autoexposure control will take effect to suit the scene’s current brightness. Set the shooting mode. Set the Mode Dial to any shooting  mode except <a>. Set the Live View shooting/Movie shooting switch to <k>.
Page 205 k Shooting Movies Cautions for movie shooting are on pages 233 and 234.  If necessary, also read the Live View shooting cautions on pages  201 and 202. In Basic Zone modes, the shooting result will be the same as in the ...
Page 206 k Shooting Movies ISO speed in Basic Zone modes The ISO speed will be set automatically within ISO 100 - 12800.  ISO speed in Creative Zone modes The ISO speed will be set automatically within ISO 100 - 12800. ...
Page 207: Scene Icons
k Shooting Movies Scene Icons During movie shooting in a Basic Zone mode, an icon representing the scene detected by the camera will be displayed and the shooting will be adapted to that scene. For certain scenes or shooting conditions, the icon displayed may not match the actual scene.
Page 208: Lcd Monitor
k Shooting Movies Manual Exposure Shooting You can manually set the shutter speed, aperture, and ISO speed for movie shooting. Using manual exposure to shoot movies is for advanced users. Set the Mode Dial to <a>. Set the Live View shooting/Movie shooting switch to <k>.
Page 209 k Shooting Movies ISO speed during manual-exposure shooting With [Auto] (A), the ISO speed will be set automatically within ISO  100 - 12800. Under [z3: ISO speed settings], if you set [ISO speed range]’s [Maximum] setting to [25600/H], the maximum ISO speed will be expanded and the ISO speed will be set automatically within ISO 100 to H.
Page 210: Information Display
k Shooting Movies Information Display Each time you press the button, the information display will change.  AF method Possible shots •d : FlexiZone - Single Maximum burst •c : Face detection Movie shooting remaining time*/ Live mode Elapsed time •f: Quick mode Battery check Movie shooting mode...
Page 211 k Shooting Movies Notes on Movie Shooting The camera cannot autofocus continuously like a camcorder.  Autofocusing during movie shooting is not recommended since it may  momentarily throw the focus far off or change the exposure. Do not point the camera toward an intense light source, such as the sun ...
Page 212 k Shooting Movies Notes on Movie Shooting You can use Remote Controller RC-6 (sold separately, p.167) to start  and stop the movie shooting if the drive mode is <Q> or <k>. Set the shooting timing switch to <2> (2-sec. delay), then press the transmit button.
Page 213: Still Photo Shooting
k Shooting Movies Shooting Still Photos While shooting a movie, you can also take a still photo by pressing the shutter button completely. Taking Still Photos during Movie Shooting If you take a still photo during movie shooting, the movie will record ...
Page 214 k Shooting Movies AEB cannot be used.  Even if an external Speedlite is used, it will not fire.  Continuous still photo shooting is possible during movie shooting.  However, the captured images will not be displayed on the screen. Depending on the still photo’s image-recording quality, number of shots during continuous shooting, card performance, etc., movie shooting may stop automatically.
Page 215: Shooting Function Settings
Shooting Function Settings Q Quick Control In Creative Zone modes, you can set the following: AF method, drive mode, image-recording quality, movie-recording size, sound- recording level (with [Sound recording: Manual] set), white balance, Picture Style, Auto Lighting Optimizer, and video snapshot. In Basic Zone modes, only the functions in bold can be set.
Page 216: Setting The Movie-Recording Size
Setting the Movie-Recording Size With [Z2: Movie rec. size], you can set the movie’s image size, frame rate per second, and compression method. The frame rate switches automatically depending on the [53: Video system] setting. Image size  A [1920x1080] : Full High-Definition (Full HD) recording quality. The aspect ratio will be 16:9.
Page 217 3 Setting the Movie-Recording Size Total Movie Recording Time and File Size Per Minute Total Recording Time (approx.) Movie- File Size Recording Size (approx.) 4 GB Card 8 GB Card 16 GB Card 16 min. 32 min. 1 hr. 4 min. 235 MB/min.
Page 218: Setting The Sound Recording
Setting the Sound Recording You can shoot movies while recording sound with the built-in monaural microphone or a commercially-available stereo microphone. You can also freely adjust the sound-recording level. Set the sound recording with [Z2: Sound recording]. Sound Recording/Sound-Recording Level [Auto] : The sound-recording level is adjusted automatically.
Page 219 3 Setting the Sound Recording Using the microphone  The built-in microphone records monaural sound. Stereo sound recording is possible by connecting an external stereo microphone (commercially-available) equipped with a miniature stereo plug (φ3.5 mm) to the camera’s external microphone IN terminal (p.20). In Basic Zone modes, the settings available for [Sound recording] will ...
Page 220: Setting The Time Code
Setting the Time Code The time code is a time reference recorded automatically to synchronize the video and audio during movie shooting. It is recorded at all times in the following units: hours, minutes, seconds, and frames. It is mainly used during movie editing.
Page 221 3 Setting the Time Code Shooting still photos during movie shooting will cause a discrepancy  between the actual time and time code. If [Free run] is set and you change the time, zone, or daylight saving  time (p.36), the time code will be affected. The time code is not recorded for video snapshots.
Page 222 3 Setting the Time Code Drop Frame If the frame rate setting is 6 (29.97 fps) or 8 (59.94 fps), the time code’s frame count causes a discrepancy between the actual time and time code. This discrepancy can be corrected automatically. This correction function is called drop frame.
Page 223: Menu Function Settings
Menu Function Settings [Z1] Menu When the Live View shooting/Movie shooting switch is set to <k>, the [Z1] and [Z2] tabs dedicated to movie shooting will be displayed. The menu options are as follows. AF method  The AF methods are the same as described on pages 192-198. You can select [FlexiZoneAF (Single)], [u Live mode], or [Quick mode].
Page 224: Sound Recording
3 Menu Function Settings [Z2] Menu Grid display  With [3x3 l] or [6x4 m], you can display grid lines to help you level the camera vertically or horizontally. Also, with [3x3+diag n], the grid is displayed together with diagonal lines to help you align the intersections over the subject for better balance in the composition.
Page 225: Shooting Video Snapshots
Shooting Video Snapshots You can easily create a short movie with the video snapshot function. A video snapshot is a short movie clip lasting approx. 2 sec., 4 sec., or 8 sec. A collection of video snapshots is called a video snapshot album and can be saved to the card as a single movie file.
Page 226 3 Shooting Video Snapshots Select [Album settings]. Select [Album settings], then press  <0>. If you want to continue shooting for  an existing album, go to “Adding to Existing Album” (p.229). Select [Create a new album]. Select [Create a new album], then ...
Page 227: Lcd Monitor
3 Shooting Video Snapshots Creating a Video Snapshot Album Shoot the first video snapshot. Press the <0> button, then shoot.  The blue bar indicating the shooting duration will gradually decrease. After the set shooting duration elapses, the shooting stops automatically. After the LCD monitor turns off and the access lamp stops blinking, the confirmation screen will appear (p.228).
Page 228 3 Shooting Video Snapshots Options in Steps 8 and 9 Function Description The movie clip will be saved as the video J Save as album (Step 8) snapshot album’s first video snapshot. The video snapshot just recorded will be added J Add to album (Step 9) to the album recorded immediately before.
Page 229 3 Shooting Video Snapshots Adding to Existing Album Select [Add to existing album]. Follow step 4 on page 226 to select  [Add to existing album], then press <0>. Select an existing album. Turn the <5> dial to select an ...
Page 230 3 Shooting Video Snapshots Cautions for Shooting Video Snapshots You can add to an album only video snapshots with the same duration  (approx. 2 sec., 4 sec., or 8 sec. each). Note that if you do any of the following while shooting video snapshots, a ...
Page 231 3 Shooting Video Snapshots Background Music Music recorded on the memory card must be used only for private  enjoyment. Do not violate the rights of the copyright holder. You can play background music when you play back albums, normal ...
Page 232 3 Shooting Video Snapshots Save the edited album. Press the <M> button to return to  the Editing panel at the screen’s bottom. Press the key to select [W]  (Save), then press <0>. The save screen will appear. To save it as a new movie, select ...
Page 233: Lcd Monitor
Movie Shooting Cautions White <s> and Red <E> Internal Temperature Warning Icons If the camera’s internal temperature increases due to prolonged movie  shooting or under a high ambient temperature, a white <s> or red <E> icon will appear. The white <s> icon indicates that the image quality of still photos will ...
Page 234 Movie Shooting Cautions Recording and Image Quality If you use a card with a slow writing speed, a five-level  indicator may appear on the right of the screen during movie shooting. It indicates how much data has not yet been written to the card (remaining capacity of the internal buffer memory).
Page 235: Image Playback
Image Playback This chapter explains how to play back and erase photos and movies, how to display them on a TV screen, and other playback-related functions. About images shot and saved with another device The camera may not be able to properly display images captured with a different camera, edited with a computer, or had their file names changed.
Page 236 x Image Playback Single-Image Display Play back the image. Press the <x> button.  The last captured image or last image viewed will appear. Select an image. To play back images starting with the  last image, turn the <5> dial counterclockwise.
Page 237: Grid Display
x Image Playback Exit the image playback. Press the <x> button to exit the  image playback and return to shooting-ready state. 3 Grid Display On the single-image display, you can overlay a playback grid. With [33: Playback grid], you can select [3x3 l], [6x4 m], or [3x3+diag This function is convenient for checking the image’s vertical or horizontal tilt, as...
Page 238: B: Shooting Information Display
B: Shooting Information Display Sample Image Taken in a Creative Zone Mode AF Microadjustment Protect images Exposure compensation amount Rating Flash exposure Folder number - compensation amount File number Aperture Histogram Shutter speed (Brightness/RGB) Picture Style/ Metering mode Settings Shooting mode ISO speed Highlight tone priority White balance...
Page 239 B: Shooting Information Display Sample Image Taken in a Basic Zone Mode Ambience and Shooting mode ambience effects Lighting or scene * With images taken in a Basic Zone mode, the information displayed will differ depending on the shooting mode. * Photos taken in the <C>...
Page 240 B: Shooting Information Display About the Highlight Alert  When [33: Highlight alert] is set to [Enable], overexposed highlight areas will blink. To obtain more image detail in the overexposed areas, set the exposure compensation to a negative amount and shoot again. About the AF Point Display ...
Page 241 B: Shooting Information Display [RGB] Display This histogram is a graph showing the distribution of each primary color’s brightness level in the image (RGB or red, green, and blue). The horizontal axis indicates the color’s brightness level (darker on the left and brighter on the right), while the vertical axis indicates how many pixels exist for each color brightness level.
Page 242: He Searching For Images Quickly
x Searching for Images Quickly H Display Multiple Images on One Screen (Index Display) Search for images quickly with the index display showing four or nine images on one screen. Press the button. Press the button during image ...
Page 243 x Searching for Images Quickly Jump through Images (Jump Display) With the single-image display, you can turn the <6> dial to jump through the images forward or backward according to the jump method set. Select [Image jump w/6]. Under the [32] tab, select [Image ...
Page 244: Magnified View
u Magnified View You can magnify a captured image by approx. 1.5x to 10x on the LCD monitor. Magnify the image. The image can be magnified during  image playback (single-image display), during image review after image capture, and from shooting-ready state. Press the ...
Page 245 u Magnified View 3 Magnification Settings Under the [33] tab, when you select [Magnificatn (apx)], you can set the starting magnification and initial position for the magnified view. 1x (no magnification)  The image will not be magnified. The magnified view will start with the single-image display.
Page 246: Rotating The Image
b Rotating the Image You can rotate the displayed image to the desired orientation. Select [Rotate image]. Under the [31] tab, select [Rotate  image], then press <0>. Select an image. Turn the <5> dial to select the  image to be rotated. You can also select an image on the ...
Page 247: Setting Ratings
Setting Ratings You can rate images and movies with one of five rating marks: l/m/ n/o/p. This function is called rating. Select [Rating]. Under the [32] tab, select [Rating],  then press <0>. Select an image or movie. Turn the <5> dial to select the ...
Page 248 3 Setting Ratings The total number of images with a given rating that can be displayed is 999. If there are more than 999 images with a given rating, [###] will be displayed for that rating. Taking Advantage of Ratings With [32: Image jump w/6], you can display only images and ...
Page 249: Q Quick Control For Playback
Q Quick Control for Playback During playback, you can press the <Q> button to set any of the following: [J: Protect images, b: Rotate image, 9: Rating, R: RAW image processing (RAW images only), S: Resize (JPEG image only), : Highlight alert, : AF point display, e: Image jump w/ 6, k: Wi-Fi*].
Page 250 Q Quick Control for Playback To rotate an image, set [51: Auto rotate] to [OnzD]. If [51: Auto rotate] is set to [OnD] or [Off], the [b Rotate image] setting will be recorded to the image, but the camera will not rotate the image for display. Pressing the <Q>...
Page 251: Enjoying Movies
k Enjoying Movies You can play back movies in the following three ways: Playback on a TV set (p.261, 264) Use the provided AV cable or an HDMI Cable HTC-100 (sold separately) to connect the camera to a TV set. Then you can play back captured movies and still photos on the TV.
Page 252 k Enjoying Movies Playback and Editing with a Computer (p.394) The movie files recorded on the card can be transferred to a computer and played with ImageBrowser EX (provided software). To have the movie play back smoothly on a computer, use a high- ...
Page 253: Playing Movies
k Playing Movies Play back the image. Press the <x> button to display  images. Select a movie. Turn the <5> dial to select the  movie to be played. On the single-image display, the  <s1> icon displayed on the upper left indicates a movie.
Page 254 k Playing Movies Movie Playback Panel Operation Playback Description 7 Play Pressing <0> toggles between play and stop. Adjust the slow motion speed by pressing the key. 8 Slow motion The slow-motion speed is indicated at the upper right of the screen.
Page 255: Editing A Movie's First And Last Scenes
X Editing a Movie’s First and Last Scenes You can edit out the first and last scenes of a movie in 1-sec. increments. On the movie playback screen, select [X]. The movie editing panel will be displayed at the bottom of the screen. Specify the part to be edited out.
Page 256 X Editing a Movie’s First and Last Scenes Save the edited movie. Select [W], then press <0>.  The save screen will appear. To save it as a new movie, select  [New file]. To save it and overwrite the original movie file, select [Overwrite].
Page 257: Slide Show (Auto Playback)
Slide Show (Auto Playback) You can play back the images on the card as an automatic slide show. Select [Slide show]. Under the [32] tab, select [Slide  show], then press <0>. Select the images to be played. Number of images to be played Press the <V>...
Page 258 3 Slide Show (Auto Playback) Item Playback Description All the still photos and movies on the card will be played jAll images back. Still photos and movies taken on the selected shooting iDate date will be played back. Still photos and movies in the selected folder will be nFolder played back.
Page 259: Start The Slide Show
3 Slide Show (Auto Playback) [Background music] Transition effect Start the slide show. Press the <V> key to select [Start],  then press <0>. After [Loading image...] is displayed, the slide show will start. Exit the slide show. To exit the slide show and return to ...
Page 260 3 Slide Show (Auto Playback) Selecting the Background Music Select [Background music]. Set [Background music] to [On],  then press <0>. Select the background music. Press the <V> key to select the  desired background music, then press <0>. You can also select multiple background music tracks.
Page 261: Viewing The Images On Tv
Viewing the Images on TV You can view the still photos and movies on a TV set. Adjust the movie’s sound volume with the TV set. The sound volume  cannot be adjusted with the camera. Before connecting or disconnecting the cable between the camera and ...
Page 262: Lcd Monitor
Viewing the Images on TV Press the <x> button. The image will appear on the TV screen. (Nothing will be displayed on the camera’s LCD monitor.) The images will automatically be  displayed at the TV’s optimum resolution. By pressing the button, you ...
Page 263 Viewing the Images on TV Connect the camera to a TV set. Use an HDMI cable to connect the  camera to the TV. The TV’s input will switch automatically to the HDMI port connected to the camera. Press the camera’s <x> button. An image will appear on the TV screen and you can use the TV’s remote control to play back images.
Page 264: Lcd Monitor
Viewing the Images on TV Viewing on Non-HD TV Sets (Connected with AV Cable) Connect the provided AV cable to the camera. With the plug’s <Canon> logo facing  the back of the camera, insert it into the <q> terminal.
Page 265: K Protecting Images
K Protecting Images Protecting an image prevents it from being erased accidentally. 3 Protecting a Single Image Select [Protect images]. Under the [31] tab, select [Protect  images], then press <0>. Select [Select images]. Select [Select images], then press  <0>.
Page 266 K Protecting Images 3 Protecting All Images in a Folder or on a Card You can protect all the images in a folder or on a card at one time. When you select [All images in folder] or [All images on card] in [x1: Protect images], all the images in the folder or on the card will be protected.
Page 267: L Erasing Images
L Erasing Images You can either select and erase images one by one or erase them in one batch. Protected images (p.265) will not be erased. Once an image is erased, it cannot be recovered. Make sure you no longer need the image before erasing it. To prevent important images from being erased accidentally, protect them.
Page 268 L Erasing Images Select [Select and erase images]. Select [Select and erase images],  then press <0>. An image will be displayed. If you press the button and turn  the <6> dial counterclockwise, you can select an image from a three- image display.
Page 269: Changing Image Playback Settings
Changing Image Playback Settings 3 Adjusting the LCD Monitor Brightness You can adjust the brightness of the LCD monitor to make it easier to read. Select [LCD brightness]. Under the [52] tab, select [LCD  brightness], then press <0>. Adjust the brightness. While referring to the gray chart, ...
Page 270: Auto Rotation Of Vertical Images
Changing Image Playback Settings 3 Auto Rotation of Vertical Images Vertical images are rotated automatically so they are displayed vertically on the camera’s LCD monitor and on the computer instead of horizontally. You can change the setting for this feature. Select [Auto rotate].
Page 271: Post-Processing Images
Post-Processing Images You can process RAW images with the camera or resize (shrink) JPEG images. The M mark shown on the right of the page title indicates  that the function is available only in Creative Zone modes (d/s/f/a/F). The camera may not be able to process images taken with ...
Page 272: R Processing Raw Images With The Camera
R Processing RAW Images with the CameraN You can process 1 images with the camera and save them as JPEG images. While the RAW image itself does not change, you can process the RAW image according to different conditions to create any number of JPEG images from it.
Page 273 R Processing RAW Images with the CameraN Displaying the setting screen Press <0> to display the setting  screen. Turn the <5> dial to change the setting. To finalize the change and return to the screen in step 3, press <0>.
Page 274: Brightness Adjustment
R Processing RAW Images with the CameraN RAW Image-processing Options Brightness adjustment  You can adjust the image brightness up to ±1 stop in 1/3-stop increments. The displayed image will reflect the setting’s effect. White balance (p.120)  You can select the white balance. If you select [P], turn the <6> dial to set the color temperature on the setting screen.
Page 275: Distortion Correction
R Processing RAW Images with the CameraN Color space (p.140)  You can select either sRGB or Adobe RGB. Since the camera’s LCD monitor is not compatible with Adobe RGB, the image will not look very different when either color space is set. Peripheral illumination correction (p.131) ...
Page 276 R Processing RAW Images with the CameraN Chromatic aberration correction  When [Enable] is set, the lens’ chromatic aberrations (color fringing along the subject’s outline) can be corrected. If [Enable] is set, the corrected image will be displayed. If the effect is difficult to discern, press the ...
Page 277: S Resize
S Resize You can resize an image to make the pixel count lower and save it as a new image. Resizing an image is possible only with JPEG 3/4/a/b images. JPEG c and RAW images cannot be resized. Select [Resize]. Under the [32] tab, select [Resize], ...
Page 278 S Resize Resize Options According to Original Image Size Available Resize Settings Original Image Size About Image Sizes The image size displayed in step 3 on the preceding page, such as [***M ****x****], has a 3:2 aspect ratio. The image size according to aspect ratios is shown in the table below.
Page 279: Sensor Cleaning
If visible spots still remain after the automatic sensor cleaning, having the sensor cleaned by a Canon Service Center is recommended. Even while the Self Cleaning Sensor Unit is operating, you can press the shutter button halfway to interrupt the cleaning and start shooting immediately.
Page 280: Automatic Sensor Cleaning
f Automatic Sensor Cleaning Whenever you set the power switch to <1> or <2>, the Self Cleaning Sensor Unit operates to automatically shake off the dust on the front of the sensor. Normally, you need not pay attention to this operation.
Page 281: Appending Dust Delete Data
Appending Dust Delete DataN Normally, the Self Cleaning Sensor Unit will eliminate most of the dust that may be visible on captured images. However, in case visible dust still remains, you can append the Dust Delete Data to the image for erasing the dust spots later.
Page 282 3 Appending Dust Delete DataN Photograph a solid-white object. At a distance of 20 cm - 30 cm (0.7 ft.  - 1.0 ft.), fill the viewfinder with a patternless, solid-white object and take a picture. The picture will be taken in aperture- priority AE mode at an aperture of f/22.
Page 283: Manual Sensor Cleaning
Before cleaning the sensor, detach the lens from the camera. The surface of the image sensor is extremely delicate. If the sensor needs to be cleaned directly, having it done by a Canon Service Center is recommended. Select [Sensor cleaning].
Page 284 If the battery level becomes low while you clean the sensor, the beeper  will sound as a warning. Stop cleaning the sensor. If a smudge that cannot be removed with a blower remains, having the  sensor cleaned by a Canon Service Center is recommended.
Page 285: Printing Images
Printing Images Printing (p.288)  You can connect the camera directly to a printer and print out the images on the card. The camera is compatible with “wPictBridge” which is the standard for direct printing. You can also use a wireless LAN to send images to a PictBridge (Wireless LAN) printer and print them.
Page 286: Preparing To Print
Preparing to Print The direct printing procedure can be performed entirely with the camera while you look at the camera’s LCD monitor. Connecting the Camera to the Printer Set the camera’s power switch to <2>. Set up the printer. For details, refer to the printer’s ...
Page 287 Preparing to Print Play back the image. PictBridge Press the < > button.  The image will appear, and the <w> icon will appear on the upper left to indicate that the camera is connected to a printer. Movies cannot be printed. ...
Page 288: Printing
w Printing The screen display and setting options will differ depending on the printer. Some settings may not be available. For details, refer to the printer’s instruction manual. Printer-connected icon Select the image to be printed. Check that the <w> icon is ...
Page 289 w Printing Q Setting the Paper Size Select the size of the paper loaded in  the printer, then press <0>. The paper type screen will appear. Y Setting the Paper Type Select the type of the paper loaded in ...
Page 290 w Printing Set the printing effects. Set it if necessary. If you do not need  to set any printing effects, go to step 5. What is displayed on the screen  differs depending on the printer. Select the option, then press <0>. ...
Page 291 w Printing Set the date and file number imprinting. Set them if necessary.  Select < >, then press <0>.  Set as desired, then press <0>.  Set the number of copies. Set it if necessary.  Select < >, then press <0>.
Page 292 w Printing e Adjustment of Printing Effects In step 4 on page 290, select the printing effect. When the <e> icon is displayed brightly next to <z>, you can press the button. You can then adjust the printing effect. What can be adjusted or what is displayed will depend on the selection made in step 4.
Page 293: Trimming The Image
w Printing Trimming the Image You can crop the image and print only Tilt correction the trimmed portion as if the image was recomposed. Set the trimming right before printing. If you set the trimming and then set the print settings, you may have to set the trimming again before printing.
Page 294: Error Messages
w Printing Depending on the printer, the trimmed image area may not be printed as  you specified. The smaller you make the trimming frame, the grainier the picture will  look in the print. While trimming the image, look at the camera’s LCD monitor. If you look ...
Page 295: W Digital Print Order Format (Dpof)
W Digital Print Order Format (DPOF) You can set the print type, date imprinting, and file number imprinting. The print settings will be applied to all print-ordered images. (They cannot be set individually for each image.) Setting the Printing Options Select [Print order].
Page 296 W Digital Print Order Format (DPOF) Standard Prints one image on one sheet. Multiple thumbnail images are printed on Index one sheet. Print type Both Prints both the standard and index prints. Date [On] imprints the recorded date on the print. File number [On] imprints the file number on the print.
Page 297: Print Ordering
W Digital Print Order Format (DPOF) Print Ordering Sel.Image  Select and order images one by one. If you press the button and turn the <6> dial counterclockwise, you can select an image from a three-image display. To return to the single-image display, turn the <6>...
Page 298: W Direct Printing Of Print-Ordered Images
W Direct Printing of Print-Ordered Images With a PictBridge printer, you can easily print images with DPOF. Prepare to print. See page 286.  Follow the “Connecting the Camera to the Printer” procedure up to step 5. Under the [31] tab, select [Print order]. Select [Print].
Page 299: Specifying Images For A Photobook
p Specifying Images for a Photobook When you select images to use in photobooks (up to 998 images) and use EOS Utility (provided software) to transfer them to a computer, the selected images will be copied into a dedicated folder. This function is useful for ordering photobooks online and for printing photobooks on a printer.
Page 300 p Specifying Images for a Photobook Specifying All Images in a Folder or on a Card You can specify all the images in a folder or on a card at one time. When [x1: Photobook Set-up] is set to [All images in folder] or [All images on card], all the images in the folder or on the card will be specified.
Page 301: Customizing The Camera
Customizing the Camera You can customize various camera functions to suit your picture-taking preferences with Custom Functions. Also, the current camera settings can be saved under the Mode Dial’s <w> and <x> positions. The functions explained in this chapter work only in the Creative Zone modes.
Page 302: Setting Custom Functions
Setting Custom FunctionsN Select [8]. Select the group. Select one of the C.Fn I-III, then  press <0>. Select the Custom Function Custom Function number number. Press the key to select the  Custom Function number, then press <0>. Change the setting as desired.
Page 303: Custom Functions
Custom FunctionsN k Movie A LV C.Fn I: Exposure Shooting Shooting Exposure level increments ISO speed setting increments p.304 In a Bracketing auto cancel (Still photo, Bracketing sequence with WB p.305 bracketing) Number of bracketed shots Safety shift p.306 C.Fn II: Autofocus Tracking sensitivity p.307 Acceleration/deceleration tracking...
Page 304: Custom Function Settings
Custom Function SettingsN C.Fn I: Exposure C.Fn I -1 Exposure level increments 0: 1/3-stop 1: 1/2-stop Sets 1/2-stop increments for the shutter speed, aperture, exposure compensation, AEB, flash exposure compensation, etc. This is effective when you prefer to control the exposure in less fine increments than 1/3-stop increments.
Page 305 3 Custom Function SettingsN C.Fn I -4 Bracketing sequence The AEB shooting sequence and white balance bracketing sequence can be changed. 0: 0a-a+ 1: -a0a+ 2: +a0a- White Balance Bracketing B/A Direction M/G Direction 0 : Standard exposure 0 : Standard white balance 0 : Standard white balance - : Decreased exposure - : Biased toward blue - : Biased toward magenta...
Page 306: Safety Shift
3 Custom Function SettingsN C.Fn I -6 Safety shift 0: Disable 1: Shutter speed/Aperture This takes effect in the shutter-priority AE (s) and aperture-priority AE (f) modes. If the subject brightness changes and the standard exposure cannot be obtained within the autoexposure range, the camera will automatically change the manually-selected setting to obtain a standard exposure.
Page 307: C.fn Ii: Autofocus
3 Custom Function SettingsN C.Fn II: Autofocus C.Fn II -1 Tracking sensitivity Sets the subject-tracking sensitivity during AI Servo AF when an obstacle enters the AF points or when the AF points stray from the subject. Default setting suited for most subjects. Suited for normal, moving subjects. [Locked on: -2 / Locked on: -1] The camera will try to continue focusing the subject even if an obstacle enters the AF points or if the subject strays from the AF points.
Page 308 3 Custom Function SettingsN C.Fn II -2 Acceleration/deceleration tracking This sets the tracking sensitivity for moving subjects whose speed can suddenly change dramatically by starting or stopping suddenly, etc. Suited for subjects that move at a fixed speed. [+2/+1] Effective for subjects having sudden movements, sudden acceleration/ deceleration, or sudden stops.
Page 309 3 Custom Function SettingsN C.Fn II -4 AI Servo 2nd image priority You can set the AF operation characteristics and shutter-release timing during continuous shooting after the first shot with AI Servo AF. [Equal priority] Equal priority is given to focusing and continuous shooting speed. In low light or with low-contrast subjects, shooting speed may slow down.
Page 310 3 Custom Function SettingsN C.Fn II -6 Lens drive when AF impossible If focus cannot be achieved with autofocus, you can have the camera keep searching for the correct focus or have it stop searching. 0: Continue focus search 1: Stop focus search If autofocus starts and the focus is far off or if focus cannot be achieved, the lens drive stops.
Page 311: C.fn Iii: Operation/Others
3 Custom Function SettingsN C.Fn II -9 AF Microadjustment Fine adjustment of the AF’s point of focus is possible for viewfinder shooting or Live View shooting in the Quick mode. For details, see page 314. C.Fn III: Operation/Others C.Fn III -1 Dial direction during Tv/Av 0: Normal 1: Reverse direction The dial’s turning direction for setting the shutter speed and aperture can be...
Page 312 3 Custom Function SettingsN C.Fn III -2 Focusing screen If you change the focusing screen, change this setting to match the focusing screen so that correct exposures are obtained. 0: Eg-A II 1: Eg-D 2: Eg-S About focusing screen characteristics Eg-A II: Standard Precision Matte Standard focusing screen that comes with the camera.
Page 313 3 Custom Function SettingsN C.Fn III -3 Multi function lock When the <R> switch is set to the right, it will prevent the <6>, <5> dial, and <9> from accidentally changing a setting. Select the camera control you want to lock, then press <0> to append a checkmark <X>...
Page 314: 8: Af Microadjustment
8: AF Microadjustment Fine adjustment of the AF’s point of focus is possible for viewfinder shooting or Live View shooting in the Quick mode. This is called “AF Microadjustment”. Before making the adjustment, read “Notes for AF Microadjustment” on page 319. Normally, this adjustment is not required.
Page 315 8: AF Microadjustment Make the adjustment. Press the key to make the  adjustment. The adjustable range is ±20 steps. Setting it toward “-: ” will shift the  point of focus in front of the standard point of focus. Setting it toward “+: ”...
Page 316 8: AF Microadjustment 2: Adjust by Lens You can make the adjustment for each lens and register the adjustment in the camera. You can register the adjustment for up to 40 lenses. When you autofocus with a lens whose adjustment has been registered, the point of focus will always be shifted by the adjustment amount.
Page 317 8: AF Microadjustment Enter the serial number. Press the key to select the  digit to be entered, then press <0> to display <r>. Press the <V> key to enter the  number, then press <0>. After entering all the digits, select ...
Page 318 8: AF Microadjustment Make the adjustment. Single focal length lens For a zoom lens, press the <V> key  and select the wide-angle (W) or telephoto (T) end. Press <0> and the box will disappear, allowing you to make the adjustment. Press the ...
Page 319 8: AF Microadjustment Clearing All AF Microadjustments When [ Clear all] appears at the bottom of the screen, pressing the <L> button will clear all the adjustments made for [1: All by same amount] and [2: Adjust by lens]. Notes for AF Microadjustment The AF’s point of focus will vary slightly depending on the subject ...
Page 320: 8: Custom Controls
8: Custom Controls You can assign often-used functions to camera buttons or dials according to your preferences. Select [C.Fn III: Operation/ Others]. Under the [8] tab, select [C.Fn III:  Operation/Others], then press <0>. Select [5]:[Custom Controls]. Select [5]:[Custom Controls], then ...
Page 321 8: Custom Controls With the screen in step 3 displayed, you can press the <L> button to cancel the Custom Control settings. Note that the [8C.Fn III -5: Custom Controls] settings will not be canceled even if you select [8: Clear all Custom Func.
Page 322: External Flash
8: Custom Controls Assignable Functions to Camera Controls Function Page Metering and AF start AF stop ONE SHOT z AI SERVO AF point direct selection Metering start AE lock/FE lock AE lock AE lock (while button pressed) Exposure AE lock (hold) FE lock Set ISO speed (hold button, turn Shutter speed setting in M mode...
Page 323 8: Custom Controls * The AF stop button ( ) is provided only on super telephoto IS lenses.
Page 324 8: Custom Controls : Metering and AF start When you press the button assigned to this function, metering and AF are executed. : AF stop The AF will stop while you hold down the button assigned to this function. Convenient when you want to lock the focus during AI Servo AF. : ONE SHOT z AI SERVO You can switch the AF operation.
Page 325 8: Custom Controls : AE lock When you press the button assigned to this function, you can lock the exposure (AE lock) during the metering. Convenient when you want to focus and meter the shot at different areas or when you want to take multiple shots at the same exposure setting.
Page 326 8: Custom Controls : Flash exposure compensation Press <0> to display the flash exposure compensation setting screen (p.170) on the LCD monitor. : Image quality Press <0> to display the image-recording quality setting screen (p.102) on the LCD monitor. : Picture Style Press <0>...
Page 327: Registering My Menu
Registering My MenuN Under the My Menu tab, you can register up to six menu options and Custom Functions whose settings you change frequently. Select [My Menu settings]. Under the [9] tab, select [My Menu  settings], then press <0>. Select [Register to My Menu].
Page 328: Register Custom Shooting Modes
w Register Custom Shooting ModesN You can register current camera settings, such as the shooting mode, menu functions, and Custom Function settings, as Custom shooting modes under the Mode Dial’s <w> and <x> positions. Select [Custom shooting mode (C1, C2)]. Under the [54] tab, select [Custom ...
Page 329 w Register Custom Shooting ModesN Settings Registered Shooting Settings  Shooting mode + settings, ISO speed, exposure compensation, flash exposure compensation, AF operation, AF point, drive mode, and metering mode. Menu functions  [z1] Image quality, Beep, Release shutter without card, Image review [z2] Lens aberration correction (Peripheral illumination correction, Chromatic aberration correction), External Speedlite control,...
Page 330 w Register Custom Shooting ModesN [C.Fn I: Exposure] Exposure level increments, ISO speed setting increments, Bracketing auto cancel, Bracketing sequence, Number of bracketed shots, Safety shift [C.Fn II: Autofocus] Tracking sensitivity, Acceleration/deceleration tracking, AI Servo 1st image priority, AI Servo 2nd image priority, AF- assist beam firing, Lens drive when AF impossible, Orientation linked AF point, Superimposed display, AF Microadjustment...
Page 331: Reference
Reference This chapter provides reference information for camera features, system accessories, etc. Certification Logo Under the [54] tab, if you select [Certification Logo Display] and press <0>, some of the logos of the camera’s certifications will appear. Other certification logos can be found in this Instruction Manual, on the camera body, and on the camera’s package.
Page 332: B Button Functions
B Button Functions When you press the button while the camera is ready to shoot, you can display [Displays camera settings], [Electronic level] (p.60), and [Displays shooting functions] (p.333). Under the [53] tab, [z button display options] enables you to select the options displayed when the ...
Page 333 B Button Functions Shooting Function Settings White balance correction Aperture AE lock Shutter speed Flash exposure compensation Shooting mode ISO speed Highlight tone priority Exposure level Wi-Fi function indicator Picture Style Custom Controls AF operation Image-recording quality Quick Control icon Possible shots Battery check Max.
Page 334: Checking The Battery Information
Purchasing a new battery is recommended. The use of a genuine Canon Battery Pack LP-E6/LP-E6N is recommended. If you use any battery other than the Battery Pack LP-E6/LP-E6N, the camera’s full performance may not be attained or malfunction may result.
Page 335 3 Checking the Battery Information Registering the Battery to the Camera You can register up to six LP-E6/LP-E6N battery packs to the camera. To register multiple battery packs to the camera, do the procedure below for each battery pack. Press the button. With the battery info.
Page 336 3 Checking the Battery Information Labeling the Serial Number on the Battery It is convenient to label all registered Battery Pack LP-E6/LP-E6N with their serial numbers, using commercially available labels. Write the serial number on a Serial number label. Write the serial number displayed on ...
Page 337 3 Checking the Battery Information Checking the Remaining Capacity of a Registered Battery Pack You can check the remaining capacity of any battery pack (even when not installed) and also when it was last used. Look for the serial number. Serial number Date last used Refer to the battery’s serial number ...
Page 338: Using A Household Power Outlet
Using a Household Power Outlet With AC Adapter Kit ACK-E6 (sold separately), you can connect the camera to a household power outlet and not worry about the remaining battery level. Connect the DC Coupler’s plug. Connect the DC Coupler’s plug to the ...
Page 339: Using Eye-Fi Cards
Using Eye-Fi Cards With a commercially-available Eye-Fi card already set up, you can automatically transfer captured images to a computer or upload them to an online service via a wireless LAN. The image transfer is a function of the Eye-Fi card. For instructions on how to set up and use the Eye-Fi card or to troubleshoot any image transfer problems, refer to the Eye-Fi card’s instruction manual or contact the card manufacturer.
Page 340 Using Eye-Fi Cards Display the connection information. Select [Connection info.], then press  <0>. Check the [Access point SSID:]. Check that an access point is  displayed for [Access point SSID:]. You can also check the Eye-Fi card’s  MAC address and firmware version. Press the <M>...
Page 341 Using Eye-Fi Cards Cautions for Using Eye-Fi Cards If [53: Wi-Fi] is set to [Enable], image transfer with an Eye-Fi card is not  possible. If “ ” is displayed, an error occurred while retrieving the card  information. Turn the camera’s power switch off and on again. Even if [Eye-Fi trans.] is set to [Disable], it may still transmit a signal.
Page 342: Function Availability Table According To Shooting Mode
Function Availability Table According to Shooting Mode For Still Photo Shooting o: Set automatically k: User selectable : Not selectable/Disabled Basic Zone Creative Zone Function 2 3 4 5 6 d s f a F All image quality settings k k k k k k k k k k k k k selectable Automatically set/...
Page 343 Function Availability Table According to Shooting Mode Basic Zone Creative Zone Function 2 3 4 5 6 F G d s f a F o o o o o o o o o k k k k k Evaluative metering Metering Metering mode mode...
Page 344 Function Availability Table According to Shooting Mode For Movie Shooting o: Set automatically k: User selectable : Not selectable/Disabled Movie Still Photos Function A C 8 d s f F M y k M All image quality settings k k k k k k k k selection (movie) All image quality settings k k k...
Page 345 Function Availability Table According to Shooting Mode Movie Still Photos Function A C 8 d s f F M y k M FlexiZone - Singled k k k k k k k k k k k Live mode c k k k k k k k k k k k Quick mode* k k k k k k k k k k k Manual focusing (MF)
Page 346: Menu Settings
Menu Settings For Viewfinder Shooting and Live View Shooting z: Shooting 1 (Red) Page 1*/41*/61* Image quality 73/83/74/84/7a/8a/b/c Beep Enable / Disable Release shutter Enable / Disable without card Image review Off / 2 sec. / 4 sec. / 8 sec. / Hold * Not selectable in <F>...
Page 347 Menu Settings z: Shooting 3 (Red) Page Exposure 1/3-stop increments, ±5 stops (AEB ±3 stops) compensation/AEB ISO speed / ISO speed range / Auto ISO range ISO speed settings / Minimum shutter speed Disable / Low / Standard / High Auto Lighting Optimizer OFF with M or Bulb...
Page 348 Menu Settings A1: Live View shooting 1 (Red) Page Live View Shooting Enable / Disable AF method FlexiZone- Single / u Live mode / Quick mode 192 Grid display Off / 3x3 l / 6x4 m / 3x3+diag n Aspect ratio 3:2 / 4:3 / 16:9 / 1:1 Exposure simulation Enable / During e / Disable...
Page 349 Menu Settings 3: Playback 2 (Blue) Page Resize Downsize the image’s pixel count Rating [OFF] / l / m / n / o / p Playback description / Display time / Repeat / Slide show Transition effect / Background music 1 image / 10 images / 100 images / Date / Image jump w/6 Folder / Movies / Stills / Rating...
Page 350 Menu Settings 5: Set-up 1 (Yellow) Page Select folder Create and select a folder File number Continuous / Auto reset / Manual reset Auto rotate OnzD / OnD / Off Format card Initialize and erase data on the card Displayed when a commercially-available Eye- Eye-Fi settings Fi card is inserted 5: Set-up 2 (Yellow)
Page 351 Menu Settings 5: Set-up 3 (Yellow) Page Video system NTSC / PAL Feature guide Enable / Disable z button display Displays camera settings / Electronic level / options Displays shooting functions Wi-Fi Disable / Enable Transfer images between cameras / Connect to smartphone / Remote control (EOS Utility) / Wi-Fi function Print from Wi-Fi printer / Upload to Web service...
Page 352 Menu Settings 8: Custom Functions (Orange) Page C.Fn I: Exposure C.Fn II: Autofocus Customize camera functions as desired C.Fn III: Operation/ Others Clear all Custom Clear all Custom Function settings Functions (C.Fn) 9: My Menu (Green) Register frequently-used menu options and My Menu settings Custom Functions...
Page 353 Menu Settings For Movie Shooting Z1: Movie1 (Red) Page FlexiZone- Single / u Live mode / Quick AF method mode Silent LV shooting Mode 1 / Mode 2 / Disable Metering timer 4 sec. / 16 sec. / 30 sec. / 1 min. / 10 min. / 30 min. Z2: Movie2 (Red) Grid display Off / 3x3 l / 6x4 m / 3x3+diag n...
Page 354: System Map
System Map Macro Ring Lite Macro Twin Lite ST-E2 ST-E3-RT 270EX II 320EX 430EX II 600EX-RT/ MR-14EX II MT-24EX 600EX Bundled Accessories 90EX Focusing screen Eg-A II Eyepiece Extender EP-EX15 Rubber Frame Eb Wide Strap E-series Dioptric EW-EOS6D Adjustment Lenses Battery Pack Battery Charger LP-E6*...
Page 355 Card slot *1: Battery Pack LP-E6N can also be used. *2: GPS Receiver GP-E2 is not compatible with the EOS 6D (N). * All cable lengths given are approximate figures. * Wireless File Transmitter WFT-E7 is not compatible with the Leather Case EH20-L EOS 6D (WG, N).
Page 356: Troubleshooting Guide
Detach and reattach the battery pack to the charger. Wait a few minutes, then reconnect the power plug to the power outlet. If the problem persists, contact your dealer or nearest Canon Service Center. The charger’s lamp does not blink.
Page 357 Troubleshooting Guide The access lamp still blinks even when the power switch is set to <2>. If the power is turned off while an image is being recorded to the  card, the access lamp will remain on/continue to blink for a few seconds.
Page 358 Troubleshooting Guide Shooting-Related Problems The lens cannot be attached. The camera cannot be used with EF-S and EF-M lenses (p.39).  No images can be shot or recorded. Make sure the card is properly inserted (p.31).  Slide the card’s write-protect switch to the write/erase position ...
Page 359 Troubleshooting Guide The image is out of focus. Set the lens focus mode switch to <AF> (p.39).  To prevent camera shake, press the shutter button gently (p.43,  44). If the lens has an Image Stabilizer, set the IS switch to <1> ...
Page 360 Troubleshooting Guide ISO 100 cannot be set. ISO speed expansion cannot be selected. If [z4: Highlight tone priority] is set to [Enable], the settable  ISO speed range will be ISO 200-25600 (or up to ISO 12800 for movie shooting). Even if you expand the settable ISO speed range in [ISO speed range], you cannot set expanded ISO speeds (L, H, H1, H2).
Page 361 Troubleshooting Guide The flash does not fire. If you use a non-Canon flash unit with Live View shooting, set  [A2: Silent LV shoot.] to [Disable] (p.190). The flash always fires at full output. If you use a flash unit other than an EX-series Speedlite, the flash ...
Page 362 Troubleshooting Guide I cannot shoot a movie. Under the [53] tab, if you set [Wi-Fi] to [Enable], you cannot shoot  movies. Before shooting movies, set [Wi-Fi] to [Disable]. Movie shooting stops by itself. If the card’s writing speed is slow, movie shooting may stop ...
Page 363 Troubleshooting Guide The manually set ISO speed changes when switching to movie shooting. If you shoot a movie when [Maximum: 25600] is set with [ISO  speed range] and ISO speed is set to ISO 16000/20000/25600, the ISO speed will switch to ISO 12800 (during movie shooting with manual exposure).
Page 364 Troubleshooting Guide When I shoot still photos during movie shooting, the movie shooting stops. Setting a lower image quality for still photos and shooting fewer  continuous still photos may resolve the problem. Time code is off. Shooting still photos during movie shooting will cause a ...
Page 365 Troubleshooting Guide Display Problems The menu screen shows few tabs and options. In Basic Zone modes, certain tabs and menu options are not  displayed. Set a Creative Zone mode (p.51). The file name’s first character is an underscore (“_”). Set the color space to sRGB.
Page 366 Troubleshooting Guide The LCD monitor does not display a clear image. If the LCD monitor is dirty, use a soft cloth to clean it.  In low or high temperatures, the LCD monitor display may seem  slow or may look black. It will return to normal at room temperature.
Page 367 Troubleshooting Guide When the movie is played back, camera operation noise can be heard. If you operate the camera’s dials or lens during movie shooting,  the operation noise will also be recorded. Using an external microphone (commercially available) is recommended (p.219). The movie has still moments.
Page 368 Troubleshooting Guide I cannot resize the image. c JPEG images and 1/41/61 images cannot be resized  with the camera (p.277). Sensor Cleaning Problems The shutter makes a noise during sensor cleaning. If you selected [Clean nowf], the shutter will make a noise, but ...
Page 369 Troubleshooting Guide Image Transfer Problems I cannot transfer images to a computer. Install the EOS Utility software on the computer (p.393).  Under the [53] tab, if [Wi-Fi] is set to [Enable], the camera cannot  connect to a computer. Set [Wi-Fi] to [Disable], then connect the camera to the computer with an interface cable.
Page 370: Error Codes
Error Message and Solution Communications between the camera and lens is faulty. Clean the lens contacts. Clean the electrical contacts on the camera and lens or use a Canon lens (p.17, 20). Card cannot be accessed. Reinsert/change card or format card with camera.
Page 371: Specifications
* Compatible with UHS-I Image sensor size: Approx. 35.8 x 23.9 mm Compatible lenses: Canon EF lenses (except EF-S and EF-M lenses) (35 mm- equivalent lens focal length will be as indicated on the lens) Lens mount: Canon EF mount •...
Page 372 Specifications Noise reduction: Applicable to long exposures and high ISO speed shots Automatic image brightness correction: Auto Lighting Optimizer Highlight tone priority: Provided Lens aberration correction: Peripheral illumination correction, Chromatic aberration correction • Viewfinder Type: Eye-level pentaprism Coverage: Vertical/Horizontal approx. 97% (with Eye point approx. 21 mm) Magnification: Approx.
Page 373 Specifications • Exposure Control Metering modes: 63-zone TTL full-aperture metering • Evaluative metering (linked to all AF points) • Partial metering (approx. 8.0% of viewfinder at center) • Spot metering (approx. 3.5% of viewfinder at center) • Center-weighted average metering Metering range: EV 1 - 20 (at room temperature with EF50mm f/1.8 II lens, ISO 100)
Page 374 * Figures in parentheses apply to an UHS-I compatible 8 GB card based on Canon’s testing standards. * Figures are based on Canon’s testing standards (ISO 100 and Standard Picture Style) and an 8 GB card. • External Speedlite...
Page 375 Specifications Metering modes: Evaluative metering (315 zones), Partial metering (approx. 11% of Live View screen), Spot metering (approx. 3% of Live View screen), Center-weighted average metering Metering range: EV 0 - 20 (at room temperature with EF50mm f/1.4 USM lens, ISO 100) Silent shooting: Provided (Mode 1 and 2) Grid display:...
Page 376 Specifications ISO speed: With autoexposure: Auto ISO (automatically set within (Recommended ISO 100 - ISO 12800), Maximum and minimum ISO exposure index) speeds can be changed in Creative Zone modes With manual exposure: Auto ISO (automatically set within ISO 100 - ISO 12800), ISO 100 - ISO 12800 set manually (in 1/3- or whole-stop increments), expandable to H (equivalent to ISO 16000/20000/25600) Time code:...
Page 377 Specifications Slide show: All images, by date, by folder, by movies, by stills, or by rating Background music: Selectable for slide shows and movie playback Image protect: Possible • Post-Processing of Images In-camera RAW image processing: Brightness correction, White balance, Picture Style, Auto Lighting Optimizer, High ISO speed noise reduction, JPEG image-recording quality, Color space, Peripheral illumination correction, Distortion correction, and...
Page 378: Operation Environment
Dimensions (W x H x D): Approx. 144.5 x 110.5 x 71.2 mm / 5.7 x 4.4 x 2.8 in. Weight (EOS 6D (WG)): Approx. 755 g / 26.7 oz. (CIPA Guidelines), Approx. 680 g / 24.0 oz. (Body only) Weight (EOS 6D (N)): Approx.
Page 379 Specifications Working humidity: 85% or less Dimensions (W x H x D):Approx. 69.0 x 33.0 x 93.0 mm / 2.7 x 1.3 x 3.7 in. Weight: Approx. 130 g / 4.6 oz. • Battery Charger LC-E6E Compatible battery: Battery Pack LP-E6/LP-E6N Power cord length: Approx.
Page 380 Case: LP1219 (sold separately) * Applies to 1/3-stop increments. With 1/2-stop increments, it will be f/22-38. All the data above is based on Canon’s testing standards and CIPA (Camera &  Imaging Products Association) testing standards and guidelines. Dimensions, maximum diameter, length and weight listed above are based on ...
Page 381 This product is designed to achieve excellent performance when used with genuine Canon accessories. Canon shall not be liable for any damage to this product and/or accidents such as fire, etc., caused by the malfunction of non-genuine Canon accessories (e.g., a leakage and/or explosion of a battery pack). Please note that this...
Page 382: Safety Precautions
Make sure to thoroughly understand and follow these precautions before using the product. If you experience any malfunctions, problems, or damage to the product, contact the nearest Canon Service Center or the dealer from whom you purchased the product. Follow the warnings below. Otherwise, death or Warnings: serious injuries may result.
Page 383 Safety Precautions When the camera or accessories are not in use, make sure to remove the battery  and disconnect the power plug from the equipment before storing. This is to prevent electrical shock, excessive heat, fire, or corrosion. Do not use the equipment where there is flammable gas. This is to prevent an ...
Page 384 For more information about the recycling of this product, please contact your local city office, waste authority, approved scheme or your household waste disposal service or visit www.canon-europe.com/weee, or www.canon-europe.com/battery. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
Page 385: Handling Precautions: Ef24-105Mm F/3.5-5.6 Is Stm
Handling Precautions: EF24-105mm f/3.5-5.6 IS STM The EF24-105mm f/3.5-5.6 IS STM utilizes a stepping motor that drives the focus lens. The motor also controls the focus lens during zooming. 1. When the camera is OFF The motor does not operate while the camera is OFF or when the camera is OFF due to the use of the auto power off function.
Page 387: Viewing The Instruction Manuals Pdf Files On The
Viewing the Instruction Manuals PDF files on the DVD-ROM / Downloading Images to Your Computer This chapter explains how to install the Camera Instruction Manual (on the DVD-ROM provided) to your computer, download images from the camera to your computer, gives an overview of the software on the EOS Solution Disk (CD-ROM), and explains how to install the software on your computer.
Page 388: Viewing The Instruction Manuals Pdf Files On The Dvd-Rom
Viewing the Instruction Manuals PDF files on the DVD-ROM The EOS Camera Instruction Manuals Disk (DVD-ROM) contains the following instruction manuals (PDF files): EOS Camera Instruction Manuals Disk XXX CEL-XXX XXX XXXXX XXXXX XXXXX XXXXX XXXXX Windows XXX XXX Mac OS X XXX XXX Camera Instruction Manual ...
Page 389 Select your language and operating system. The index of the Instruction Manuals is displayed. EOS 6D (WG) EOS 6D (N) ENGLISH The EOS 6D (N) does not have the Wi-Fi and GPS functions. INSTRUCTION MANUAL Camera Instruction Manual Adobe Reader (latest version recommended) must be installed to view the Instruction Manual files (PDF format).
Page 390 Select your language and operating system. The index of the Instruction Manuals is displayed. EOS 6D (WG) EOS 6D (N) ENGLISH The EOS 6D (N) does not have the Wi-Fi and GPS functions. INSTRUCTION MANUAL Camera Instruction Manual Adobe Reader (latest version recommended) must be installed to view the Instruction Manual files (PDF format).
Page 391: Downloading Images To A Computer
Downloading Images to a Computer You can use the provided software to download the images in the camera to your computer. There are two ways to do this. Download by Connecting the Camera to the Computer Install the software (p.395) Use the provided interface cable to connect the camera to your computer.
Page 392: Downloading Images With A Card Reader
Use ImageBrowser EX. For details, refer to the Software  Instruction Manual PDF (p.388). When downloading images from the camera to your computer, with a card reader without using Canon software, copy the DCIM folder on the card to your computer.
Page 393: About The Software
About the Software EOS Solution Disk EOS Solution Disk XXX This disk contains various software applications for EOS cameras. CEL-XXX XXX XXXXX XXXXX XXXXX XXXXX XXXXX Windows XXX XXX Mac OS X XXX XXX Note that the software provided with previous cameras might not support still photos and movie files shot with this camera.
Page 394 Shooting locations can be displayed on a map on a computer screen by using the geotag information recorded using the GPS function. The ZoomBrowser EX/ImageBrowser programs that came with previous cameras does not support the EOS 6D’s still photos and MOV movie files. Use ImageBrowser EX.
Page 395: Installing The Software
Installing the Software Installing the Software on Windows Compatible OS Windows 8.1 Windows 8 Windows 7 Check that the camera is not connected to your computer Never connect the camera to your computer before you install the  software. The software will not be installed correctly. Insert the EOS Solution Disk (CD).
Page 396 Check that the camera is not connected to your computer. Insert the EOS Solution Disk (CD). On your computer’s desktop, double-click and open the CD-ROM icon, and then double-click [Canon EOS Digital Installer]. Select your geographic area, country and language. Click [Easy Installation] to start installation.
Page 398: Index
Index Numerics Audio/video output ....251, 261 Auto Lighting Optimizer....125 10-sec. or 2-sec. delay ....100 Auto playback....... 257 11-point AF auto selection ....94 Auto power off ......34, 55 1280x720 ........216 Auto reset........137 1920x1080 ........216 Auto rotate........270 4- or 9-image index display...242 Autofocus 9 AF 640x480 ........216...
Page 399 Index Center-weighted average Drive mode ....... 73, 98 metering ........150 Dust Delete Data ......281 Charger ........26, 28 Chromatic aberration correction..132 Electronic level ....... 60, 326 Cleaning........279 Erasing images......267 Clear camera settings .....56 Error codes........370 Close-ups........77 Evaluative metering...... 149 Color space........140 Exposure compensation....
Page 400 Index Flash-sync speed .....171, 173 Household power ......338 Manual flash ......174 Shutter synchronization ICC profile ........140 (1st/2nd curtain) .......175 Wireless........175 Illumination (LCD panel)....48 Flash exposure Image dust prevention....279 compensation .......170, 176 Image review........55 Flash mode ........174 Image-recording quality....
Page 401 Index Landscapes........76 M (manual exposure) ... 148, 208 Language ........38 Macro photography ......77 Large (image-recording quality) ..103 Magnification ........ 245 LCD monitor........17 Magnified view...... 199, 244 Brightness adjustment ....269 Main Dial ........45 Electronic level ......60 Malfunction ........356 Image playback ......235 Manual exposure....
Page 402 Noise reduction Print order (DPOF)....295 High ISO speed ......126 Printing effects ......290 Long exposures......128 Tilt correction ......293 Nomenclature .........20 Trimming ........293 Non-Canon flash units ....171 Program AE......142, 204 Normal (image-recording quality) ..102 Program shift ......143...
Page 403 Index Protect (image erase protection)...265 Shooting mode ....... 24 Av (Aperture-priority AE) ..146 B (Bulb) ........154 w (Custom shooting)....328 (Quick Control) ...49, 83, 185, 215, 249 M (Manual exposure) ....148 P (Program AE)......142 Quick Control Dial ......46 Tv (Shutter-priority AE) ....
Page 404 Index Spot metering........150 Wi-Fi..........351 Wind filter ........218 S-RAW (Small RAW) ....104 sRGB ..........140 Stopped-down aperture ....147 Strap ..........27 System map........354 Temperature warning ....201, 233 Time code ........220 Time zone ........36 Tone priority ........130 Toning effect (monochrome) ..117 Trimming (for printing)....293 Tripod socket ........21 Tv (shutter-priority AE)....144 USB (digital) terminal....286, 391...
Page 406 CANON EUROPA N.V. PO Box 2262, 1180 EG Amstelveen, The Netherlands For your local Canon office, please refer to your warranty card or to www.canon-europe.com/Support The product and associated warranty are provided in European countries by Canon Europa N.V. The descriptions in this Instruction Manual are current as of March 2015. For information on the compatibility with any products introduced after this date, contact any Canon Service Center.

This manual is also suitable for:

Eos 6d n Eos 6d wg

Canon EOS 6D Instruction Manual

Introduction

Getting Started

Basic Shooting

Basic Shooting

Setting the AF and Drive Modes

Setting the AF and Drive Modes

Image Settings

Image Settings

Advanced Operations

Flash Photography

Shooting with the LCD Monitor

(Live View Shooting)

Shooting with the LCD Monitor (Live View Shooting) 179

Shooting Movies

LCD Monitor

Image Playback

Post-Processing Images

Sensor Cleaning

Printing Images

Customizing the Camera

Reference

Viewing the Instruction Manuals PDF Files on the

DVD-ROM / Downloading Images to Your Computer

Quick Links

Related Manuals for Canon EOS 6D

Summary of Contents for Canon EOS 6D