Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Omega OS641C-MV-LS
- Page 1 OMEGA...
-
Page 3: Safety Information
This instrument is a portable easy use compact-sized digital infrared tempera- ture transducer with laser marker designed for simple one hand operation. SAFETY INFORMATION It is recommended that you read the safety and operation instructions before using the infrared thermometer. symbol on the instrument indicates that the operator must refer to an explanation in this manual. - Page 4 • Do not use the unit near any device which generates strong electromagnetic radiation or near a static electrical charge, as these may cause errors. • Do not use the unit where it may be exposed to corrosive or explosive gases. The unit may be damaged, or explosion may occur.
-
Page 5: Specifications
GENERAL Low battery indication: the "Red LED " is displayed when the battery voltage drops below the operating level. Operating Environment: 0°C to 50°C at < 70% relative humidity. Storage Temperature: -20°C to 60°C, 0 to 80% R.H. with battery removed from meter. - Page 6 ELECTRICAL Temperature Range: -20°C to 260°C. Analog Output: 1mV/°C. Accuracy: ±3% of reading or ±3°C, whichever is greater @ 18 to 28°C ambient operating temperature. Temperature Coefficent: ±0.2% of reading or ±0.2°C, whichever is greater, change in accuracy per °C change in ambient operating temperature above 28°C or below 18°C.
- Page 7 Spot size increases with distance from the probe tip as shown CAUTION: Use of controls or Adjustments Danger, Certification & ID Label: (Located on back of unit) or performance of Procedures other than those Specified herein may result in Hazardous radiation exposure. Aperture Label (on front):...
-
Page 8: Operating Instructions
OPERATING INSTRUCTIONS Push buttons Laser Marker Button Release MEAS button then press " " button to toggle between turn on and turn off the Laser Marker annunciator, If " " annunciator turn on, press MEAS button the laser marker beam is being emitted, releasing MEAS button turn off the laser marker beam. -
Page 9: Operation
1. Plug the infrared temperature transducer test leads into the Vdc input jack and common or ground input jack on the DMM. Observe polarity. 2. Set the DMM to the 2V range only, ignore the decimal point. 3. Use " " button to select turn on or turn off the Laser Marker. 4. -
Page 10: Measurement Considerations
MEASUREMENT CONSIDERATIONS 1. Theory of Measurement Every object emits infrared energy in accordance with its temperature. By mesuring the amount of this radiant energy, it is possible to determine the temperature of the emitting object. 2. About Infrared Infrared radiation is a form of light (electromagnectic radiation), and has the property that it, passes easily through air while it is easily absorbed by solid matter. - Page 11 4. Emissivity All objects emit invisible infrared energy. The amount of energy emitted is proportional to the object's temperature and its ability to emit IR energy. This ability, called emissivity, is based upon the material that the object is made of and its surface finish.
-
Page 12: Maintenance
MAINTENANCE Battery Replacement Power is supplied by four 1.5V (AAA size) batteries. The "LOW BATT" red LED lighted when replacement is needed.To replace the batteries, remove the screw from the back of the meter and lift off the battery cover case. Remove the batteries from battery contacts. - Page 13 Substance Thermal emissivity Asphalt 0.90 to 0.98 Concrete 0.94 Cement 0.96 Sand 0.90 Earth 0.92 to 0.96 Water 0.92 to 0.96 0.96 to 0.98 Snow 0.83 Glass 0.90 to 0.95 Ceramic 0.90 to 0.94 Marble 0.94 Plaster 0.80 to 0.90 Mortar 0.89 to 0.91 Brick (red)
- Page 14 OMEGA warrants this unit to be free of defects in materials and workmanship and to give satisfactory service for a period of 13 months from date of purchase. OMEGA Warranty adds an additional one (1) month grace period to the normal one (1) year product warranty to cover handling and shipping time.
- Page 15 constantly pursuing certification of its products to the European New Approach Directives. OMEGA will add the CE mark to every appropriate device upon certification. The information contained in this document is believed to be correct but OMEGA Engineering, Inc. accepts no liability for any errors it contains, and reserves the right to alter specifications without notice.
- Page 16 Where Do I Find Everything I Need for Process Measurement and Control? HEATERS PRESSURE/STRAIN AND FORCE FLOW/LEVEL M-2865/0799 OMEGA...Of Course! TEMPERATURE ENVIRONMENTAL MONITORING AND CONTROL pH/CONDUCTIVITY DATA ACQUISITION...