Connector - Sony MVC-CD300 Service Manual

MVC-CD200/CD300
For Schematic Diagram
• Refer to page 4-19 for printed wiring board.
2 3
1
SY-67 BOARD(9/10)
CONNECTOR(CN BLOCK) NO MARK:STILL/PB MODE
A
-REF.NO.:5000 SERIES-
XX MARK:NO MOUNT
CN703 5P
TO SELF_TIMER 5
TK-61 BOARD
REG_GND 4
CN501
THROUGH THE
LENS_CAP_OPEN 3
FP-369 FLEXIBLE
PRELAMP_AF_ON 2
(SEE PAGE
4-18) CAM_P_5V 1
B
8P
CN702
STB_CHARGE 1
STRB_PHOTO_ON 2
A_4.9V 3
FLASH
UNIT UNREG_GND 4
C
PHOTO_TR_OUT 5
UNREG 6
STROB_ON 7
XSTB_FULL 8
FLASH UNIT is replaced as a block.
So the PRINTED WIRING BOARD and
SCHEMATIC DIAGRAM are omitted.
D
CN711 2P
MIC_SIG 1
MIC901
MIC_GND 2
E
D701
XX
F
CN705 14P
DIAL_B 1
DIAL_A 2
GND 3
KEY_AD3 4
CAM_3.1V 5
TO
N.C 6
G CONTROL SWITCH
BLOCK(ZK-503) XPOWER_ON 7
N.C 8
(SEE PAGE
4-55)
GND 9
N.C 10
XPB_ON 11
12
XSET_UP
MODE_DIAL 13
CAM_3.1V 14
H
D707
XX
16

CONNECTOR

SY-67 (9/10)
4 5 6
Note: Resistor is mounted to the location
where FB701 is printed.
SELF_TIMER
XLENS_CAP_OPEN
PRELAMP_AF_ON
Q701
UN9113J-(K8).SO
SWITCH
D705 4.9
XX
S3.1/P0
CAM_DD_ON
Q702
UN9213J-(K8).SO
SWITCH
STRB_AIN
R723
0
STRB_ON
STRB_PHOTO_ON
R724
1k
XSTB_FULL
D702
XX
STB_CHG
A_4.9V
CAM_P_5V
ST_UNREG
CAM_3.1V
D_3.4V
REG_GND
MIC_SIG
LND702
FB701
0
LND701
Note
FLAME_GND
D703
XX
C701
D704
2200p
1SS352-TPH3
B
DIAL_B
DIAL_A
KEY_AD3
XPWR_ON
XPB_ON
XSETUP_ON
MODE_DIAL
D710
XX
D708 D709
XX
XX
4-39
7 8 9
36 21
TO(4/10) TO(2/10) EXT_STRB_ON
C703
0.1u B
45
TO(7/10) LANC_SIG
C704
7
TO(1/10)
0.1u
B
XLANC_JACK_IN
47
TO(7/10)
LANC_DC
USB_JACK_IN
AV_JACK_IN
C705
0.1u
B
28
TO(3/10) V_OUT
35
TO(4/10) C706
2200p
B
AU_OUT
55
TO(8/10)
AU_GND
42 TO(6/10(CN701),
VDD
7/10)
22
TO(2/10) USB_D+PULLUP
USB_D+OUT
USB_D-OUT
USB_TXENL
29
TO(4/10)
USB_XVDATA
49
TO(7/10) USB_D+IN
USB_D-IN
USB_SUSPND
R711
USB_VBUS
0
XEJECT
57 47
TO(10/10) TO(7/10) XLID_OPEN
VL_3V
53
TO(8/10)
NOT USE XSHTR_ON
48
TO(7/10)
XAE_LOCK_SW
D712
XX
BATT_SIG
46
TO(7/10)
BATT/XEXT
FAST_CHARGE
INIT_CHARGE
51
TO(7/10)
XPOWER_LED
KEY_AD0
KEY_AD1
10 11 12 13
CN709
27P
27 EXT_STROB_ON
Note :
26 REG_GND
The components identified by
25 LANC_SIG mark 0 or dotted line with mark
24 REG_GND 0 are critical for safety.
23 XLANC_JACK_IN
Replace only with part number
22 LANC_DC
specified.
21 USB_DET
20 AV_JACK_IN
19 REG_GND
18 V_OUT
17 REG_GND
16 A_OUT
TO
JK-208 BOARD
15 REG_GND
CN101
14 D_3.4V
THROUGH THE
FP-361 FLEXIBLE
13 VDD
(SEE PAGE 4-57)
12 USB_D+PULLUP
11 USB_D+OUT
10 USB_D-OUT
9 USB_TXENL
SIGNAL PATH
8 USB_XVDATA
7 USB_D+IN
6 USB_D-IN
5 USB_SUSPND CHROMA
4 REG_GND
REC
3 XEJECT
PB
2 XLID_OPEN
1 VL_3V
CONTROL SWITCH
BLOCK(RL-503)
CN710 6P
1 XSHTR_ON
2 XAE_LOCK_SW
3 NC
4 GND
5 NC
(SHUTTER)
6 NC
LOCK ON
CONTROL SWITCH BLOCK(RL-503) is replaced as a block.
So the PRINTED WIRING BOARD is omitted.
CN708 11P
11 REG_GND
10 BATT_SIG
9 REG_GND
8 BATT/XEXT
TO
7 FAST_CHARGE FS-83 BOARD
CN001
6 INIT_CHARGE
THROUGH THE
FP-362 FLEXIBLE
5 D_3.4V
(SEE PAGE 4-57)
4 REG_GND
3 POWER_LED
2
KEY_AD0
1 KEY_AD1
4-40
14 15
Note :
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
VIDEO SIGNAL
AUDIO
Y Y/CHROMA SIGNAL