Related Manuals for Omega DRN-PS-1000
Summary of Contents for Omega DRN-PS-1000
- Page 1 UserÕ s Guide MADE ® http://www.omega.com e-mail: info@omega.com DRN-PS-1000 UNIVERSAL SWITCHING POWER SUPPLY Compact DIN-Rail 24 Volt...
- Page 2 It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI regulations that apply. OMEGA is constantly pursuing certification of its products to the European New Approach Directives. OMEGA will add the CE mark to every appropriate device upon certification.
-
Page 3: Table Of Contents
General Information and Features Safety Considerations Installation and Removal 3.1 Installation Clearance 3.2 Mounting on DIN Rail 3.3 Removal of Unit Input and Output Connections 4.1 Block Diagram 4.2 Wiring for 115 Vac - Single Phase 4.3 Wiring for 230 Vac - Two Phase Specifications Input Power Output Power... -
Page 4: General Information And Features
ENERAL The compact DRN power supplies are designed to supply well-regulated 24 volt DC power to sensors, signal conditioners, data acquisition systems and high level logic equipment. Significant DRN features include: ¥ Features ¥ ¥ ¥ ¥ ¥ ¥ ¥ ¥... -
Page 5: Safety Considerations
This device is marked with the international Caution symbol. It is important to read this manual before installing or commissioning this device as it contains important information relating to Safety and EMC (Electromagnetic Compatibility). Unpacking & Inspection Unpack the instrument and inspect for obvious shipping damage. Do not attempt to operate the unit if damage is found. -
Page 6: Installation And Removal
EMOVAL If a rail assembly is to be transported, then disconnection, dismounting and separate Warning! packing of the power supply is recommended. For units that must be shipped installed on the rail, additional bracing to resist transportation shocks is recommended. -
Page 7: Installation Clearance
Ensure that there is enough room for mounting the power supply unit. There should be a minimum of 1" [25mm] spacing to allow sufficient air circulation for proper cooling. Signal Conditioner Modules NSTALLATION AND 1" 24V-Bus Figure 3.1 Ñ Mounting EMOVAL 1" Power Supply... -
Page 8: Mounting On Din Rail
NSTALLATION AND 3.2 Mounting on DIN Rail To install unit onto DIN Rail 1. Tilt unit position mounting guide onto DIN Rail, as shown. 2. Push unit towards DIN Rail and it will snap into place. 1. Tilt 35mm Rail 2. -
Page 9: Removal Of Unit
3.3 Removal of Unit The mounting guide can remain on DIN Rail and Power Supply can be removed. 1. While holding mounting guide, push unit upwards and unit will detach from mounting guide. 35mm Rail Figure 3.4 Figure 3.5 NSTALLATION AND Push Up Hold Guide Ñ... -
Page 10: Input And Output Connections
4.1 Block Diagram of Power Supply Figure 4.1 Ñ Block Diagram 4.2 Wiring Warning: Do not turn on the ac power to the power supply unit until you have completed all output connections. Failure to do so may result in injury! This device must only be installed electrically by a specially trained electrician with corresponding qualifications. -
Page 11: Wiring For 115 Vac - Single Phase
NPUT AND 4.2 Wiring (Continued) 115Vac - Single phase power wiring Input Power USE AWG 12-26 WIRE Figure 4.2Ñ Wiring for 115Vac - Single Phase UTPUT ONNECTIONS FUSE *• USE A SWITCH TO APPLY • +24V POWER TO THE LOAD, •... -
Page 12: Wiring For 230 Vac - Two Phase
NPUT AND 4.3 Wiring (Continued) 230Vac - Two phase power wiring Figure 4.3Ñ Wiring for 230Vac - Two Phase UTPUT ONNECTIONS FUSE 1 FUSE 2 * • USE A SWITCH TO APPLY • +24V POWER TO THE LOAD, • IF THE CAPACITANCE OF •... -
Page 13: Specifications
INPUT POWER Input Voltage: Frequency: Current: Overvoltage Protection: 275 Volt Varistor Overcurrent Protection: Fuse TR-5 800mA Time-lag / IEC 127-3 Input Wattage: OUTPUT POWER Output Voltage: Output Wattage: * For higher output wattage greater than 20 watts follow the chart on section 7, Figure 6.2. -
Page 14: General
PECIFICATIONS GENERAL Operating Temperature: Storage Temperature: Mounting: Size: Weight: Equipment Type: Overvoltage: Pollution Degree: Insulation input to ouput: WIRE CONNECTIONS Screw down wire clamps, AWG 12 to 26 (ferrules recommended for stranded wire). 23¡ to 122¡F(-5¡ to 50¡C) -40¡ to 176¡F(-40¡ to 80¡C) 32 and 35mm DIN Rail Height: 3.00"... -
Page 15: Dimensions
IMENSIONS 0.9" (23mm) 3.00" (76mm) 3.67" (93mm) -
Page 16: Temperature Derating Graph
NPUT AC VOLTAGE AC INPUT CURRENT @ 100VAC INPUT OUTPUT POWER 120V 265V 115V INPUT AC VOLTAGE 110V 105V 100V Example: If ambient is 50¼C, maximum wattage is 21W max. for 120-265Vac. If unit is operated at 21W at an input voltage of 100V, the maximum ambient temperature allowed is 40¼C. - Page 19 Service Department will issue an Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is found to be defective it will be repaired or replaced at no charge. OMEGAÕs WARRANTY does not apply to defects resulting from any action of the purchaser, including but not limited to mishandling, improper interfacing, operation outside of design limits, improper repair, or unauthorized modification.
- Page 20 Where Do I Find Everything I Need for Process Measurement and Control? OMEGAÉOf Course! TEMPERATURE Thermocouple, RTD & Thermistor Probes, Connectors, Panels & Assemblies Wire: Thermocouple, RTD & Thermistor Calibrators & Ice Point References Recorders, Controllers & Process Monitors Infrared Pyrometers PRESSURE, STRAIN AND FORCE Transducers &...