1 Safety Precautions 1.1. General Guidelines 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
2 Warning 2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensi- tive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec- trostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor [chip] components.
2.2. About lead free solder (PbF) Note: Lead is listed as (Pb) in the periodic table of elements. In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder. The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu). That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
3 Service Navigation 3.1. Important Notice 3.1.1. MANUFACTURING ID NO. This service manual is for MANUFACTURING ID NO. TC-L32X1N as indicated in the label at side and the model name plate of the unit. 3.2. Different P.C.B. Parts No. Parts name & Description...
3.3. Service Hint Board Name Function A-Board Rear Terminal, AV Switch, MCU, Audio & Video Processor, LVDS, Tuner V-Board Remote Receiver, LED P-Board Power (AC/DC), DC-DC Non-serviceable P-Board should be exchanged for service. Control Panel Assy Control Button, Power switch Non-serviceable Control Panel Assy should be exchanged for service.
4 Specifications Power Source AC 110-127 V, 60 Hz Power Consumption Maximum 120 W Standby Condition 0.7 W Display panel Aspect Ratio 16:9 Visible screen size 32 inch class (31.5 inches measured diagonally) (W × H × Diagonal) 27.5 inch × 15.4 inch × 31.5 inch (698 mm × 392 mm × 800 mm) 1,049,088 (1,366 (W) ×...
5 Service Mode 5.1. How to enter into Service Mode While pressing [VOLUME ( - )] button of the main unit, press [INFO] button of the remote control three times within 2 seconds. 5.1.1. Key command [1] button...Main items Selection in forward direction [2] button...Main items Selection in reverse direction [3] button...Sub items Selection in forward direction [4] button...Sub items Selection in reverse direction...
5.2. SRV-TOOL 5.2.1. How to access 1. Select [SRV-TOOL] in Service Mode. 2. Press [OK] button on the remote control. 5.2.2. Display of SOS History SOS History (Number of LED blinking) indication. From left side; Last SOS, before Last, three occurrence before, 2nd occurrence after shipment, 1st occurrence after shipment. This indication except 2nd and 1st occurrence after shipment will be cleared by [Self-check indication and forced to factory ship- ment setting].
5.3. Hotel mode 1. Purpose Restrict a function for hotels. item Function 2. Access command to the Hotel mode setup menu Mode Select hotel mode off/on In order to display the Hotel mode setup menu, please Input Select input signal modes. enter the following command (within 2 second).
6 Troubleshooting Guide Use the self-check function to test the unit. 1. Checking the IIC bus lines 2. Power LED Blinking timing 6.1. Check of the IIC bus lines 6.1.1. How to access Self-check indication only: Produce TV reception screen, and while pressing [VOLUME ( - )] button on the main unit, press [OK] button on the remote control for more than 3 seconds.
6.2. Power LED Blinking timing chart 1. Subject Information of LED Flashing timing chart. 2. Contents When an abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, the defective block can be identified by the number of blinks of the Power LED on the front panel of the unit.
6.3. No Power First check point There are following 2 states of No Power indication by power LED. 1. No lit 2. Red is lit then turns red blinking a few seconds later. (See 6.2.)
7 Disassembly and Assembly Instructions 7.3. AC cord Caution Exchange printed circuit board after confirm parts number. 1. Remove the screw and Remove the AC cord bracket. 2. Remove the bushing of the AC cord from the AC cord Parts name & Description Parts No.
7.5. Side AV bracket 7.7. Control panel 1. Remove the 1 screw (C). 1. Disconnect the connector (K1). 2. Remove the 1 screw (D). 2. Remove the 2 screws. 3. Remove the side AV bracket. 3. Remove the control panel. 7.6.
7.9. P-Board Plastic frame 7.11. VESA metal 1. Remove the 4 screws. 1. Remove the 2 screws (E). 2. Remove the P-Board Plastic frame. 2. Remove the 4 screws (F). 3. Remove the VESA metal. 7.10. A-P-MTG Metal 1. Remove the 5 screws. 2.
8 Measurements and Adjustments 8.1. Voltage chart of A-board VOLTAGE TEST POINT SPECIFICATION (Reception state) STB3.3V TP2843 3.3 ± 0.16 V STB1.8V TP7006 1.84 ± 0.09 V SUB1.2V TP5602 1.26 ± 0.06 V SUB1.8V TP5601 1.84 ± 0.09 V SUB3.3V TP5600 3.3 ±...
8.3. Picture level adjustment (VIDEO) Instrument Name Remarks 1. REMOTE TRANSMITTER 2. Video signal generator (100% Color bar) Adjustment or Inspection Procedure Remarks <procedure> 1. Receive 100% Color bar. (ASPECT: ZOOM or FULL, Picture mode: VIVID, AI Picture: OFF) * BACK LIGHT MAX VALUE <Inspection>...
9 Block Diagram 9.1. Main Block Diagram A-BOARD 27MHz IFD1/2 TS Serial FRONT END Digital/Analog CLOCK Tuner 74MHz EEPWP EEPROM DDR2 SDRAM 27MHz IIC3 TV-V TS Serial HDMI1 TV-L,R RESET HDMI2 SWITCH Digital Video signal FLASH HDMI3 MEMORY HUNSON2 RESET V,Y,C Video front-end, VIDEO2...
10 Wiring Connection Diagram 10.1. Caution statement. Caution: Please confirm that all flexible cables are assembled correctly. Also make sure that they are locked in the connectors. Verify by giving the flexible cables a very slight pull. 10.2. Wiring...
11.2. A-Board (1/11) Schematic Diagram A-BOARD TXN/A10PSRS (1/11) IC8001 Peaks-Lite2,DDR MN2WS0047 Peaks-Lite2 B PORT (Sub Video LOSD OUT (for HQ1) FOR HQ1L VIDEO FOR ADV7493 TO 7/11 Input or Address) CPU BUS I/F POD,CI I/F IC8001 VOP21 LOSDOUT11 IC8001 VOP20 LOSDOUT10 TO 6/11 MVCLK...
13.2. Electrical Replacement Parts List 13.2.1. Replacement Parts List Notes...
Page 52
13.2.2. Electrical Replacement Parts List Safety Ref. No. Part No. Part Name & Pcs Remarks Description Safety Ref. No. Part No. Part Name & Pcs Remarks C3218 F1G1H101A731 C 100PF, K, 50V Description C3219 F1G1H330A731 C 33UF, 50V C3701 F1H1A1050032 C 10UF, 50V K1FY124D0001 12P CONNECTOR PAVCA C4000...
Page 53
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description C4243 F1G1C104A116 C 0.10UF, K, 16V C4532 F1J1A106A043 C 0.010UF, K, C4256 F1G1H331A730 C 330UF, 50V PAVCA C4600 F1G1C104A116 C 0.10UF, K, 16V C4257 F1G1H332A730 C 3300UF, 50V...
Page 54
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description C5606 F1H1C105A145 C 0.01UF, K, 16V C8309 F1G1H102A730 C 1000UF, 50V C5607 F1G1H221A459 C 220UF, 50V C8310 F1G1C104A116 C 0.10UF, K, 16V C5611,12 F1K1C1060004 C 0.010UF, 16V C8311...
Page 55
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description D4430 MA2J1110GL DIODE IC7006 C0CBCYE00001 IC D4431 MAZ8047GML ZENER DIODE IC8001 MN2WS0047 D4432-35 MA2J1110GL DIODE IC8002 C3ABSY000036 IC D4436 B0BC4R700007 ZENER DIODE IC8004...
Page 56
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description Q2106 B1ABCF000231 TRANSISTOR R3115 ERJ2GEJ101 M 100 OHM, J,0.063W Q2350 B1ABCF000231 TRANSISTOR R3116,17 ERJ2GEJ220 M 22 OHM, Q2500 B1ABCF000231 TRANSISTOR J,0.063W Q2504...
Page 57
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description R3249 ERJ2GEJ221 M 220 OHM, R4081 ERJ2GEJ473 M 47KOHM, J,0.063W J,0.063W R3252 ERJ2GEJ103 M 10KOHM, R4082 ERJ2GEJ220 M 22 OHM, J,0.063W J,0.063W R3265...
Page 58
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description R4160 ERJ2GEJ103 M 10KOHM, R4399 ERJ2GEJ101 M 100 OHM, J,0.063W J,0.063W R4161 ERJ2RKF20R0X M 20 OHM, , PAVCA R4401-03 ERJ2GEJ101 M 100 OHM,...
Page 59
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description R4561 ERJ2GEJ473 M 47KOHM, R5484 ERJ2GEJ203X J,0.063W 20KOHM,J,0.063W R4564,65 ERJ2GEJ220 M 22 OHM, R5486,87 ERJ2GEJ473 M 47KOHM, J,0.063W J,0.063W R4567 D1BB4701A055 M 4.7KOHM, 1/10W...
Page 60
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description R8082 ERJ2RKF75R0 M 75 OHM, , R8532 ERJ2GEJ560X M 56 OHM, 0.063W J,0.063W R8083 ERJ2GEJ301 M 300 OHM, R8540-45 ERJ2GEJ220 M 22 OHM,...
Page 61
Any attempt to service or repair the product or products dealt with in this Service Bulletin by anyone else could result in serious injury or death. 2009 Panasonic Corporation of North America. All rights reserved. Unauthorized copying and distribution is a violation of law.