OPERATION MANUAL MODEL XG-P25X LCD PROJECTOR XG-P25X/CD/H(E) 02.3.19, 7:18 PM...
Page 2
• If the new fitted plug contains a fuse, its value is the same as that removed from the cut-off plug. • The cord grip is clamped over the sheath of the mains lead, and not simply over the lead wires. IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN. XG-P25X/CD/CE+UK (E) 02.3.19, 7:35 PM...
Page 3
O CD-ROM fornecido contém instruções de operação em lnglês, Alemão, Francês, Sueco, Espanhol, Italiano, Holandês, Português, Chinês (Chinês Tradicional e Chinês Simplificado), Coreano e Árabe. Leia cuidadosamente todas as instruções de operação antes de operar o projetor LCD. XG-P25X/CD/SUP 02.3.19, 7:20 PM...
2. CONSUMER PRODUCT SAFETY ACT To ensure that you will promptly receive any safety notification of inspection, modification, or recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.
BEFORE REMOVING THE SCREW, DISCONNECT POWER CORD. HOT SURFACE INSIDE ALLOW 1 HOUR TO COOL BEFORE REPLACING THE LAMP. REPLACE WITH SAME SHARP LAMP UNIT TYPE BQC-XGP25X//1 ONLY. UV RADIATION : CAN CAUSE EYE DAMAGE. TURN OFF LAMP BEFORE SERVICING.
This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instruc- tions have been adhered to. XG-P25X/CD (E)-a 02.3.19, 7:15 PM...
Page 7
• Macintosh is a registered trademark of Apple Computer, Inc. in the United States and/or other countries. • All other company or product names are trademarks or registered trademarks of their respective companies. • This software is based in part on the work of the Independent JPEG Group. XG-P25X/CD (E)-a 02.3.19, 7:15 PM...
Caution Concerning the Lamp Unit SEE OPERATION MANUAL. Potential hazard of glass particles if lamp ruptures. In case of lamp rupture, contact your nearest Sharp Authorized LCD Projector Dealer or Service Center for a replacement. See “Replacing the Lamp” on pages...
This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security System. Refer to the information that came with the system for instructions on how to use it to secure the projector. Kensington Security Standard connector XG-P25X/CD (E)-a 02.3.19, 7:15 PM...
And, with Digital Convergence, a slight distortion of convergence can be adjusted on the service menu screen without having to touch the LCD panel. XG-P25X/CD (E)-a 02.3.19, 7:16 PM...
Displaying a Still Image ......Magnifying a Specific Portion of an Image ........Display and Setting the Break Timer ..Computer Image Adjustments using AUTO SYNC ......Adjusting the Picture Aspect Ratio ..Gamma Correction Function ....XG-P25X/CD (E)-a 02.3.19, 7:16 PM...
Page 13
Features ........... Maintenance & Troubleshooting Lamp/Maintenance Indicators ..... Replacing the Lamp ......Replacing the Air Filter ......Troubleshooting ........For SHARP Assistance ......Appendix Connecting Pin Assignments ..... (RS-232C) Specifications and Command Settings......Wired Remote Control Terminal Specifications ........Compatibility Chart ......
• If the desired pdf file cannot be opened by double clicking the mouse, start Acrobat Reader first, then specify the desired file using the “File”, “Open” menu. • See the “readme.txt” file on the CD-ROM for important information on the CD-ROM not included in this operation manual. E-11 XG-P25X/CD (E)-a 02.3.19, 7:16 PM...
ø3.5 mm minijack cable (commercially available) from the wired RC jack on the bottom of the remote control to the WIRED REMOTE control input terminal on the rear of the projector. ø3.5 mm minijack cable (commercially available) E-14 XG-P25X/CD (E)-a 02.3.19, 7:17 PM...
RS-232C serial control cable (32 10 (10.0 m)) AN-C10RS DVI to 15-pin D-sub adaptor (7.9 (20 cm)) AN-A1DV • All cables may not be available in all regions. Please check with your nearest Sharp Authorized LCD Projector Dealer or Service Center. E-15 XG-P25X/CD (E)-a 02.3.19, 7:17 PM...
Make the necessary connections before proceeding. Connect the power cord to a wall outlet. The POWER indicator lights up red and the projector enters standby mode. POWER indicator • If the bottom filter cover is not securely installed, the POWER indicator flashes. E-16 XG-P25X/CD (E)-b 02.3.19, 7:03 PM...
When connecting this projector to a computer, select “RGB” for “Signal Type” on the GUI menu. (See page • A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Sharp Authorized LCD Projector Dealer or Service Center.
Page 21
• Before using the “Plug and Play” function, be sure to turn on the projector first and the connected computer last. • The DDC “Plug and Play” function of this projector operates only when used in conjunction with a VESA DDC compatible computer. E-18 XG-P25X/CD (E)-b 02.3.19, 7:04 PM...
Page 22
• The wireless mouse or RS-232C function may not operate if your computer port is not correctly set up. Please refer to the operation manual of the computer for details on setting up/installing the correct mouse driver. • A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Sharp Authorized LCD Projector Dealer or Service Center.
• If your video equipment does not have an S-video output terminal, use a composite video cable. CAUTION • Always turn off the projector before connecting to video equipment, in order to protect both the projector and the equipment being connected. E-20 XG-P25X/CD (E)-b 02.3.19, 7:04 PM...
• The AUDIO OUTPUT terminal allow you to output audio to audio components from the selected AUDIO INPUT 1 to 5 terminals connected to audiovisual equipment. • For details on Variable Audio Output (VAO) and Fixed Audio Output (FAO), see page • A ø3.5 mm stereo minijack to stereo RCA audio cable adaptor may be necessary. E-21 XG-P25X/CD (E)-b 02.3.19, 7:04 PM...
Ensure the cooling fan has stopped before disconnecting the power cord. DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE. E-22 XG-P25X/CD (E)-b 02.3.19, 7:04 PM...
• Do not forcefully turn the lens shift dial beyond the 10:0 and 5:5 orientating positions; doing so may result in damaging the equipment. • When the AN-P9MX of optional lens is attached, lens shift cannot be used. E-23 XG-P25X/CD (E)-b 02.3.19, 7:04 PM...
• Digital shift function only works with BORDER, STRETCH or SMART STRETCH of VIDEO and DTV inputs. (See page for details.) The DIGITAL SHIFT screen is not displayed when projecting images other than WIDE. Digital Shift Press ∂. Press ƒ. E-24 XG-P25X/CD (E)-b 02.3.19, 7:04 PM...
• A polarizing screen cannot be used with this projector. Two optional lenses from Sharp are also available for specialized application. Please see your local Sharp Authorized LCD Projector Dealer to details on all the lenses. (Refer to the lens operation manual when attaching a lens.) Also, be sure to have service personnel install the AN-P9MX and AN-P48EZ optional lenses.
Page 29
• Optimal image quality is produced with the projector positioned perpendicular to the screen with all feet flat and level. Tilting or angling the projector will reduce the effectiveness of the lens shift function. E-26 XG-P25X/CD (E)-b 02.3.19, 7:05 PM...
Page 30
(Lower) = 0.0817x • There is an error of 3% in the formula above. • Values with a minus ( ) sign indicate the distance of the lens center below the bottom of the screen. E-27 XG-P25X/CD (E)-b 02.3.19, 7:05 PM...
Page 31
Lens center to the lower edge of the screen (H) (inches) • There is an error of 3% in the formula above. • Values with a minus ( ) sign indicate the distance of the lens center below the bottom of the screen. E-28 XG-P25X/CD (E)-b 02.3.19, 7:05 PM...
Page 32
(Lower) = 0.0817x • There is an error of 3% in the formula above. • Values with a minus ( ) sign indicate the distance of the lens center below the bottom of the screen. E-29 XG-P25X/CD (E)-b 02.3.19, 7:05 PM...
Ceiling-mount Projection • It is recommended that you use the optional Sharp ceiling-mount bracket for this installation. • Before mounting the projector, contact your nearest...
Projector Remote control VOLUME On-screen Display Muting the Sound Projector Remote control Press MUTE to temporarily turn off the sound. Press MUTE again to turn the sound back on. MUTE On-screen Display E-31 XG-P25X/CD (E)-c 02.3.19, 7:06 PM...
You can also use this function to display a still image FREEZE from a computer while you make preparations for the next computer images to be presented. Press FREEZE to freeze the image. Press FREEZE again to return to the moving image. On-screen Display E-32 XG-P25X/CD (E)-c 02.3.19, 7:06 PM...
• See page “Auto Sync Adjustment” for setting the Auto SYNC Sync. • Auto Sync adjustment may take some time to complete, depending on the image of the computer connected to the projector. On-screen Display E-34 XG-P25X/CD (E)-c 02.3.19, 7:06 PM...
CINEMA Gives greater depth to darker portions of image for a more exciting theater experience. Allows you to adjust gamma value using Sharp CUSTOM Advanced Presentation Software. Press GAMMA. Each time GAMMA is pressed, the gamma level toggles as shown on the left.
Press UNDO to return to the previous screen. To exit from the GUI, press MENU. • For details on items on the menu screen, see the tree charts on pages INPUT 4, 5 (VIDEO) mode (Example) E-38 XG-P25X/CD (E)-d 02.3.19, 7:07 PM...
Sharp frequency figures displayed above are for example purposes only. Custom • “Color”, “Tint”, and “Sharp” appear only when None Component input is selected in INPUT 1 or 2 mode. For Economy Mode INPUT 3 (DVI), in “Picture” menu, only “CLR Temp” is Power Save [LOW POWER/STANDARD] active and the other menus are displayed in gray.
• The adjustments can be stored separately in the INPUT 1 to 5 modes. • Depending on the type of signal received, “Sharp” may not be adjustable for COMPONENT input in INPUT 1 or 2 mode. Adjusting the Color Temperature This function can be used to adjust the color temperature to suit the type of image input to the projector (video, computer image, TV broadcast, etc.).
• In PAL50Hz or SECAM, the two-two pull down enhancement will be enabled only in the Film Mode, when the film source has been entered. E-42 XG-P25X/CD (E)-d 02.3.19, 7:08 PM...
• If a memory position has not been set, a resolution and frequency setting will not be displayed. • When selecting the stored adjustment setting with “Select Setting”, the computer system should match the stored setting. E-43 XG-P25X/CD (E)-d 02.3.19, 7:08 PM...
Page 47
• Avoid displaying computer patterns which repeat every other line (horizontal stripes). (Flickering may occur, making the image hard to see.) • When inputting DTV 480P or 1080I signals, select the corresponding type of signal. Checking the Input Signal This function allows you to check the current input signal information. E-44 XG-P25X/CD (E)-d 02.3.19, 7:08 PM...
Page 48
• When the optimum image cannot be achieved with Auto Sync adjustment, use manual adjustments. (See page Auto Sync Display Function Normally, an image is not superimposed during Auto Sync adjustment. You can, however, choose to superimpose a background image during Auto Sync adjustment. E-45 XG-P25X/CD (E)-d 02.3.19, 7:08 PM...
VAO (Variable audio output): Audio output that varies in strength with the volume level of the source projector. Speaker Switching the built-in speakers on the projector ON/OFF. E-46 XG-P25X/CD (E)-d 02.3.19, 7:08 PM...
Digital Noise Reduction (DNR) provides high quality images with minimal dot crawl and cross color noise. See page for the procedure details. • If the image is clear, select “ ” to prevent any blurring. E-47 XG-P25X/CD (E)-d 02.3.19, 7:08 PM...
• AUTO cannot be set for PAL-M and PAL-N input signals. Select “PAL-M” or “PAL-N” in “Video System” menu for PAL-M and PAL-N input signals. E-48 XG-P25X/CD (E)-d 02.3.19, 7:08 PM...
A custom image (e.g. your company logo) can be uploaded to the projector via an RS-232C cable. See page in this operation manual, and also the supplied Sharp Advanced Presentation Software operation manual on the CD-ROM for detailed instructions. See page for the procedure details.
Monitor Out/RS-232C on CAUTION • Set “MNTR Out/RS232C” to “ ” when using the Sharp Advanced Presentation Software (supplied). Automatic Power Shutoff Function When no input signal is detected for more than 15 minutes, the projector will automatically shut off. The on-screen message, “Power OFF in 5 min.”...
Description Front Normal image Ceiling Front Inverted image Rear Reversed image Ceiling Rear Reversed and inverted image • This function is used for the reversed image and ceiling-mount setups. See page for these setups. E-51 XG-P25X/CD (E)-e 02.3.19, 7:10 PM...
Level B All operation buttons on the projector are unavailable. • To cancel the Keylock Level, perform the above procedure using the remote control. • See page for details using the password function. E-52 XG-P25X/CD (E)-e 02.3.19, 7:10 PM...
See page for the procedure details. • Make sure that both the projector and computer are set for the same baud rate. Refer to the computer’s operation manual for instructions for setting the baud rate. E-53 XG-P25X/CD (E)-e 02.3.19, 7:11 PM...
• Be sure to set the ID No. in the Option menu and attach a corresponding number seal to the projector. • The ID No. can be set from 001 to 250. • For details on intended purpose, see pages E-54 XG-P25X/CD (E)-e 02.3.19, 7:11 PM...
This function can be used to display all the adjusted settings on the screen simultaneously. See page for the procedure details. INPUT 1, 2 (RGB) or 3 (DIGITAL) mode INPUT 4, 5 (VIDEO) mode E-56 XG-P25X/CD (E)-e 02.3.19, 7:11 PM...
RS-232C connection. Output terminals are provided (RS-232C on the projector) enabling a daisy chain configuration and eliminating the need for a distributor. This projector is also equipped with a function to send status information (lamp usage time, etc.) to a Sharp Service Center or outside contractor for quick and efficient customer service.
Page 61
Video Source 2 This projector can be used in a network of projectors managed from a single PC with the accompanied Sharp Advanced Presentation Software Professional Edition. Projectors in conference rooms on the first and third floors of a building, for example, can be used for video presentations, while projectors on the second floor can be used for PC-assisted presentations.
Page 62
Projectors can be stacked using an RS-232C cable (cross type, sold separately). See page for recommended connection of an RS-232C serial control cable. • See page , “Setting the Stacking Mode”, and page , “Deselecting Inputs”. E-59 XG-P25X/CD (E)-f 02.3.19, 7:11 PM...
Page 63
• For more information on this feature, see the operation manuals accompanying the Sharp Advanced Presentation Software Professional Edition. • When UXGA signal is displayed, the videowall can not be set by Sharp Advanced Presentation Software Professional Edition. E-60 XG-P25X/CD (E)-f...
• Clogged air filter. • Clean the filter. (See page • Cooling fan breakdown. • Take the projector to your nearest Sharp • Internal circuit failure. Authorized LCD Projector Dealer or Service Center for repair. • Burnt-out lamp.
BQC-XGP25X//1 from your nearest Sharp Authorized LCD Projector Dealer or Service Center. Then carefully change the lamp by following the instructions below. If you wish, you may have the lamp replaced at your nearest Sharp Authorized LCD Projector Dealer or Service Center.
Page 66
“LAMP 0000H” is displayed, socket of the projector. ENTER on the projector, press indicating that the lamp timer is POWER ON on the projector. reset. • Reset the lamp timer only after replacing the lamp. E-63 XG-P25X/CD (E)-g 02.3.19, 7:12 PM...
• The air filters should be cleaned every 100 hours of use. Clean the filters more often when the projector is used in a dusty or smoky location. • Have your nearest Sharp Authorized LCD Projector Dealer or Service Center exchange the filter (PFILD0080CEZZ) when it is no longer possible to clean it.
• Set the resolution mode to 480P. (See page Image is green on INPUT 1 or • Change the input signal type. (See page 2 COMPONENT. Image is pink (no green) on INPUT 1, 2 RGB. E-65 XG-P25X/CD (E)-g 02.3.19, 7:13 PM...
For SHARP Assistance If you encounter any problems during setup or operation of this projector, first refer to the “Troubleshooting” section on page . If this operation manual does not answer your question, please contact the SHARP Service Department listed below. U.S.A.
Analog Horizontal sync 5 V Power Analog Ground* Ground* • * Return for 5 V, Hsync. and Vsync. • * Analog R, G and B return • * These pins are not used on this equipment. E-67 XG-P25X/CD (E)-h 02.3.19, 7:13 PM...
OK OR ERR V-SIZE ( 30 – OK OR ERR FREEZE ON OK OR ERR DIGITAL SHIFT ( 96 – OK OR ERR FREEZE OFF OK OR ERR AUTO SYNC START OK OR ERR E-68 XG-P25X/CD (E)-h 02.3.19, 7:13 PM...
Page 72
INPUT 4 (VIDEO 1) TINT ( 30 – OK OR ERR RGB GAMMA : STANDARD OK OR ERR INPUT 4 (VIDEO 1) SHARP ( 30 – OK OR ERR RGB GAMMA : PRESENTATION OK OR ERR INPUT 4 (VIDEO 1) CLR TEMP ( 3 –...
Page 73
LANGUAGE SELECTION : SVENSKA OK OR ERR BACKGROUND SELECTION : NONE OK OR ERR LANGUAGE SELECTION : OK OR ERR STARTUP IMAGE SELECTION : SHARP OK OR ERR LANGUAGE SELECTION : PORTUGUÊS OK OR ERR STARTUP IMAGE SELECTION : CUSTOM OK OR ERR...
• System codes C1 to C5 are fixed at “10110”. are complex and are, therefore, not listed here. • Codes C14 and C15 are reverse confirmation bits, with “10” indicating “Front” and “01” indicating “Rear”. Sharp remote control signal format Transmission format: 15-bit format 67.5 ms 67.5 ms Wave form of output signal: Output using Pulse Position Modulation 26.4 µs...
1,200 VESA format UXGA signals, sampling occurs and the image is displayed with 1,024 lines, causing part of the image to be blocked. Signal Horizontal Frequency (kHz) Vertical Frequency (Hz) 15.7 480P 31.5 15.6 580P 31.3 720P 45.0 1035 33.8 1080 33.8 E-72 XG-P25X/CD (E)-h 02.3.19, 7:14 PM...
UDSKAA005WJZZ), LCD projector operation manual (TINS-A133WJZZ), Quick reference guides, Sharp Advanced Presentation Software installation guide (TINS-A139WJZZ), ID number seal (TLABZ0781CEZZ) This SHARP projector uses LCD (Liquid Crystal Display) panels. These This unit has some inactive TFTs within acceptable tolerances which very sophisticated panels contain 786,432 pixels ( RGB) TFTs (Thin may result in illuminated or inactive dots on the picture screen.
Mode that stretches the 4:3 image horizontally to display it fully on a 16:9 screen. Sync on green Video signal mode of a computer which overlaps horizontal and vertical sync signal to green color signal pin. E-75 XG-P25X/CD (E)-h 02.3.19, 7:14 PM...