Page 1 2 0 1 5 O W N E R ’ S M A N U A L I n f o r ma t i o n P r o v i d e d b y :...
Page 2 This manual illustrates and describes the operation of VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name FCA features and equipment that are either standard or op- US LLC shall be deemed to be deleted and the name FCA tional on this vehicle.
Page 3: Introduction 3
TABLE OF CONTENTS SECTION PAGE INTRODUCTION ............. . . 3 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE .
Page 4 I n f o r ma t i o n P r o v i d e d b y :...
Page 5: Table Of Contents
INTRODUCTION CONTENTS INTRODUCTION ......4 VEHICLE IDENTIFICATION NUMBER ..6 HOW TO USE THIS MANUAL ....4 VEHICLE MODIFICATIONS/ALTERATIONS .
Page 6: Introduction
4 INTRODUCTION When it comes to service, remember that your authorized INTRODUCTION dealer knows your vehicle best, has factory-trained tech- Congratulations on selecting your new FCA US LLC nicians and genuine parts, and cares about your satisfac- vehicle. Be assured that it represents precision workman- tion.
Page 7 INTRODUCTION 5 I n f o r ma t i o n P r o v i d e d b y :...
Page 8: Vehicle Identification Number
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire Owner’s Manual, you may miss important information.
Page 9: Vehicle Modifications/Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. VIN Location NOTE: It is illegal to remove or alter the VIN. I n f o r ma t i o n P r o v i d e d b y :...
Page 10 I n f o r ma t i o n P r o v i d e d b y :...
Page 11 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A WORD ABOUT YOUR KEYS ... . .11 ▫ To Disarm The System ....18 ▫...
Page 12 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE STARTING SYSTEM — IF EQUIPPED . .24 OCCUPANT RESTRAINT SYSTEMS ..42 ▫ How To Use Remote Start ....25 ▫...
Page 13: A Word About Your Keys
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 Key Fob against the Engine START/STOP button and A WORD ABOUT YOUR KEYS push to operate the ignition. Your vehicle uses a keyless ignition system. This system consists of a Key Fob with Remote Keyless Entry (RKE) transmitter and a Keyless Push Button Ignition.
Page 14: Key Fob
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Key Fob The Key Fob also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the Key Fob go dead.
Page 15: Ignition Or Accessory On Message
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Ignition Or Accessory On Message Opening the driver’s door when the ignition is in ACC or ON (engine not running), a chime will sound to remind you to cycle the ignition to OFF. In addition to the chime, the ignition or accessory on message will display in the cluster.
Page 16: Sentry Key
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • Do not leave children or animals inside parked • When leaving the vehicle, always remove the Key vehicles in hot weather. Interior heat build-up may Fob from the vehicle and lock your vehicle. cause serious injury or death.
Page 17 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 The system uses a Key Fob with a factory-mated Remote Should this occur, have the vehicle serviced as soon as Keyless Entry (RKE) transmitter, a Keyless Push Button possible by an authorized dealer. Ignition and a RF receiver to prevent unauthorized vehicle operation.
Page 18: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE When having the Sentry Key® Immobilizer System serviced, Replacement Keys bring all vehicle keys with you to an authorized dealer. NOTE: Only Key Fobs that are programmed to the vehicle electronics can be used to start and operate the Customer Key Programming vehicle.
Page 19: Vehicle Security Alarm - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 VEHICLE SECURITY ALARM — IF EQUIPPED To Arm The System The Vehicle Security Alarm monitors the vehicle doors Follow these steps to arm the Vehicle Security Alarm: for unauthorized entry and the Keyless Enter-N-Go™ 1.
Page 20: To Disarm The System
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Push the LOCK button on the Remote Keyless Entry NOTE: (RKE) transmitter. • The driver’s door key cylinder and the trunk button on 3. If any doors are open, close them. the RKE transmitter cannot arm or disarm the Vehicle Security Alarm.
Page 21: Security System Manual Override
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 exterior lights will flash, the horn will sound. If this NOTE: occurs, disarm the Vehicle Security Alarm. • The front courtesy overhead console and door cour- tesy lights will turn on if the dimmer control is in the Security System Manual Override “Dome ON”...
Page 22: To Unlock The Doors
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Driving at speeds 5 mph (8 km/h) and above To Unlock The Doors disables the system from responding to all RKE transmit- Push and release the UNLOCK button on the RKE ter buttons for all RKE transmitters.
Page 23: To Lock The Doors
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Flash Lights With Lock If the vehicle is equipped with Passive Entry, refer to “Keyless Enter-N-Go™” under “Things To Know Before This feature will cause the turn signal lights to flash when Starting Your Vehicle”...
Page 24: Using The Panic Alarm
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • You may need to be less than 35 ft (11 m) from the Using The Panic Alarm vehicle when using the RKE transmitter to turn off the To turn the Panic Alarm feature on or off, push and hold Panic Alarm due to the radio frequency noises emitted the PANIC button on the RKE transmitter for at least one by the system.
Page 25 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 1. Remove the emergency key by sliding the mechanical of the RKE transmitter apart. Make sure not to damage latch on the back of the RKE transmitter sideways the seal during removal. with your thumb and then pull the key out with your other hand.
Page 26: General Information
The system has a range of approximately 300 ft (91 m). I n f o r ma t i o n P r o v i d e d b y :...
Page 27: How To Use Remote Start
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 NOTE: • Battery at an acceptable charge level • The vehicle must be equipped with an automatic • RKE panic button not pushed transmission to be equipped with Remote Start. • System not disabled from previous remote start event •...
Page 28 26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Start Abort Message To Enter Remote Start Mode The following messages will display in the instrument cluster if the vehicle fails to remote start or exits remote Push and release the REMOTE START button start prematurely: on the RKE transmitter twice within five sec- onds.
Page 29: Door Locks
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 • For security, power window and power sunroof op- To Exit Remote Start Mode And Drive The Vehicle eration (if equipped) are disabled when the vehicle is Before the end of 15-minute cycle, push and release the in the Remote Start mode.
Page 30 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • For personal security and safety in the event of a collision, lock the vehicle doors before you drive as well as when you park and leave the vehicle. • When leaving the vehicle, always make sure the keyless ignition node is in the “OFF”...
Page 31: Power Door Locks
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 WARNING! (Continued) • Do not leave the Key Fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter-N-Go™...
Page 32 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you push the power door lock switch while the ignition Automatic Unlock Doors On Exit is in the ACC or ON/RUN position, and any front door The doors will unlock automatically on vehicles with is open, the power locks will not operate.
Page 33: Child-Protection Door Lock System - Rear Doors
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 Child-Protection Door Lock System — Rear Doors To provide a safer environment for small children riding in the rear seats, the rear doors are equipped with Child-Protection Door Lock system. To Engage Or Disengage The Child-Protection Door Lock System 1.
Page 34: Keyless Enter-N-Go
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: For emergency exit from the rear seats when the • If wearing gloves on your hands, or if it has been Child-Protection Door Lock System is engaged, manually raining on the Passive Entry door handle, the unlock raise the door lock knob to the unlocked position, roll sensitivity can be affected, resulting in a slower re- down the window, and open the door using the outside...
Page 35 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 To Unlock From The Passenger Side With a valid Passive Entry RKE transmitter within 5 ft (1.5 m) of the passenger door handle, grab the front passenger door handle to unlock all four doors automati- cally.
Page 36 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE FOBIK-Safe only executes in vehicles with passive entry. NOTE: The vehicle will only unlock the doors when the There are three situations that trigger a FOBIK-Safe doors are locked using the door panel switch, a valid search in any passive entry vehicle.
Page 37 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 To Enter The Trunk With a valid Passive Entry RKE transmitter within 3 ft (1.0 m) of the deck lid, push the button on the right side of CHMSL (Center High Mounted Stop Light), which is located on the deck lid.
Page 38 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Lock The Vehicle’s Doors Do NOT grab the door handle when pushing the door handle lock button. This could unlock the door(s). With one of the vehicle’s Passive Entry RKE transmitters within 5 ft (1.5 m) of the driver or passenger front door handles, push the door handle LOCK button to lock all four doors.
Page 39: Windows
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 NOTE: • After pushing the door handle button, you must wait two seconds before you can lock or unlock the doors, using either Passive Entry door handle. This is done to allow you to check if the vehicle is locked by pulling the door handle, without the vehicle reacting and unlocking.
Page 40 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: For vehicles equipped with the Uconnect®, the AUTO-Down Feature power window switches will remain active for up to 10 The driver door power window switch and some model minutes after the ignition is placed in the OFF position. passenger door power window switches have an AUTO- Opening either front door will cancel this feature.
Page 41 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 To close the window part way, lift the window switch to Reset Auto-Up the first detent and release it when you want the window Should the Auto Up feature stop working, the window to stop.
Page 42: Wind Buffeting
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE (setting it in the DOWN position). To enable the window Wind Buffeting controls and the rear sunscreen, push and release the Wind buffeting can be described as the perception of window lockout button again (setting it in the UP pressure on the ears or a helicopter-type sound in the position).
Page 43: Trunk Safety Warning
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 NOTE: The transmission must be in PARK before the With the ignition in the OFF position, the Trunk Open button will operate. symbol will display until the trunk is closed. Refer to “Keyless Enter-N-Go™” in “Things To Know The trunk lid can be released from Before Starting Your Vehicle”...
Page 44: Trunk Emergency Release
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Trunk Emergency Release OCCUPANT RESTRAINT SYSTEMS As a security measure, a Trunk Internal Emergency Release Some of the most important safety features in your lever is built into the trunk latching mechanism. In the vehicle are the restraint systems: event of an individual being locked inside the trunk, the •...
Page 45 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 2. If a child from 2 to 12 years old (not in a rear-facing 6. All occupants should always wear their lap and child restraint) must ride in the front passenger seat, shoulder belts properly.
Page 46: Seat Belt Systems
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ejection and the risk of injury caused by striking the WARNING! inside of the vehicle. Everyone in a motor vehicle should be belted at all times. • Never place a rear-facing child restraint in front of an air bag.
Page 47 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 After the sequence completes, the Seat Belt Reminder NOTE: If BeltAlert has been deactivated, the Seat Belt Light remains illuminated until the respective seat belts Reminder Light will continue to illuminate while the are buckled.
Page 48 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • Do not allow people to ride in any area of your • Relying on the air bags alone could lead to more vehicle that is not equipped with seats and seat severe injuries in a collision.
Page 49 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 WARNING! (Continued) WARNING! (Continued) • A lap belt worn too high can increase the risk of • A seat belt that is too loose will not protect you injury in a collision. The seat belt forces won’t be at properly.
Page 50 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. The seat belt latch plate is above the back of the front WARNING! (Continued) seat, and next to your arm in the rear seat (for vehicles • A shoulder belt placed behind you will not protect equipped with a rear seat).
Page 51 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Positioning The Lap Belt 4. Position the lap belt so that it is snug and lies low across your hips, below your abdomen.
Page 52 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. Position the shoulder belt across the shoulder and 2. At about 6 to 12 in (15 to 30 cm) above the latch plate, chest with minimal, if any slack so that it is comfort- grasp and twist the seat belt webbing 180 degrees to able and not resting on your neck.
Page 53 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 NOTE: The adjustable upper shoulder belt anchorage is equipped with an Easy Up feature. This feature allows the shoulder belt anchorage to be adjusted in the upward position without pushing or squeezing the release but- ton.
Page 54 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Pregnant women should wear the lap part of the seat belt WARNING! across the thighs and as snug across the hips as possible. Keep the seat belt low so that it does not come across the •...
Page 55 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 The pretensioners are triggered by the Occupant Re- Restraints” section of this manual. The table below straint Controller (ORC). Like the air bags, the preten- defines the type of feature for each seating position. sioners are single use items.
Page 56 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the passenger seating position is equipped with an WARNING! ALR and is being used for normal usage, only pull the seat belt webbing out far enough to comfortably wrap • Never place a rear-facing child restraint in front of around the occupant’s mid-section so as to not activate an air bag.
Page 57: Supplemental Restraint System (Srs)
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 How To Disengage The Automatic Locking Mode WARNING! (Continued) Unbuckle the combination lap/shoulder belt and allow it • Do not use the Automatic Locking Mode to restrain to retract completely to disengage the Automatic Locking occupants who are wearing the seat belt or children Mode and activate the vehicle sensitive (emergency) who are using booster seats.
Page 58 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Knee Impact Bolsters words “SRS AIRBAG” or “AIRBAG” are embossed on the air bag covers. • Advanced Front Air Bags • Supplemental Side Air Bags • Supplemental Knee Air Bags • Front and Side Impact Sensors •...
Page 59 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 output appropriate to the severity and type of collision as WARNING! determined by the Occupant Restraint Controller (ORC), which may receive information from the front impact • Being too close to the steering wheel or instrument sensors or other system components.
Page 60 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • Relying on the air bags alone could lead to more • No objects should be placed over or near the air severe injuries in a collision. The air bags work bag on the instrument panel or steering wheel, with your seat belt to restrain you properly.
Page 61 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 On the other hand, depending on the type and location of way as the air bags inflate to their full size. The Advanced impact, Advanced Front Air Bags may deploy in crashes Front Air Bags fully inflate in less time than it takes to with little vehicle front-end damage but that produce a blink your eyes.
Page 62 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Driver Knee Air Bag This vehicle is equipped with a Supplemental Driver Knee Air Bag mounted in the instrument panel below the steering column. The Supplemental Driver Knee Air Bag provides enhanced protection during a frontal impact by working together with the seat belts, pretensioners, and Advanced Front Air Bags.
Page 63 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 When the SAB deploys, it opens the seam on the out- board side of the seatback’s trim cover. The inflating SAB deploys through the seat seam into the space between the occupant and the door. The SAB moves at a very high speed and with such a high force that it could injure you if you are not seated properly, or if items are positioned in the area where the SAB inflates.
Page 64 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE rollover events, in addition to the injury reduction poten- WARNING! tial provided by the seat belts and body structure. • Your vehicle is equipped with left and right The SABICs deploy downward, covering the side win- Supplemental Side Air Bag Inflatable Curtains dows.
Page 65 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 The SABICs and SABs (“Side Air Bags”) are designed to Seat belts (and child restraints where appropriate) are activate in certain side impacts and certain rollover necessary for your protection in all collisions. They also events.
Page 66 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE deploys the left Side Air Bags only and a right side WARNING! (Continued) impact deploys the right Side Air Bags only. • Relying on the Side Air Bags alone could lead to The Side Air Bags will not deploy in all side collisions, more severe injuries in a collision.
Page 67 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 event may be in progress and whether deployment is If you do have a collision which deploys the air bags, any appropriate. A slower-developing event may deploy the or all of the following may occur: seat belt pretensioners on both sides of the vehicle.
Page 68 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE continues, see your doctor. If these particles settle on NOTE: your clothing, follow the garment manufacturer’s in- • Air bag covers may not be obvious in the interior trim, structions for cleaning. but they will open during air bag deployment.
Page 69 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 • Turn on the interior lights, which remain on as long as START or ON/RUN position. If the ignition switch is in the battery has power or until the ignition switch is the OFF position or in the ACC position, the air bag turned to the “OFF”...
Page 70 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE diagnostics also record the nature of the malfunction. WARNING! While the air bag system is designed to be maintenance free, if any of the following occurs, have an authorized Ignoring the Air Bag Warning Light in your instru- dealer service the air bag system immediately.
Page 71 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 Redundant Air Bag Warning Light Maintaining Your Air Bag System WARNING! If a fault with the Air Bag Warning Light is detected, which could affect the Supplemental • Modifications to any part of the air bag system Restraint System (“SRS”), the Redundant Air could cause it to fail when you need it.
Page 72 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE bag deployment or hitting a road obstacle, data that will WARNING! (Continued) assist in understanding how a vehicle’s systems per- • Do not attempt to modify any part of your air bag formed.
Page 73: Child Restraints
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 NOTE: EDR data are recorded by your vehicle only if a Every state in the United States, and every Canadian non-trivial crash situation occurs; no data are recorded by province, requires that small children ride in proper the EDR under normal driving conditions and no per- restraint systems.
Page 74 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE There are different sizes and types of restraints for NOTE: children from newborn size to the child almost large • For additional information, refer enough for an adult safety belt. Always check the child www.seatcheck.org or call 1–866–SEATCHECK.
Page 75 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Summary Of Recommendations For Restraining Children In Vehicles Child Size, Height, Weight Or Age Recommended Type Of Child Restraint Infants and Children who are two years old or Either an Infant Carrier or a Convertible Toddlers younger and who have not reached the Child Restraint, facing rearward in the rear...
Page 76 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants And Child Restraints WARNING! Safety experts recommend that children ride rear-facing • Never place a rear-facing child restraint in front of in the vehicle until they are two years old or until they an air bag.
Page 77 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 Older Children And Child Restraints All children whose weight or height is above the forward-facing limit for the child seat should use a Children who are two years old or who have outgrown belt-positioning booster seat until the vehicle’s seat belts their rear-facing convertible child seat can ride forward- fit properly.
Page 78 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • When your child restraint is not in use, secure it in • Improper installation can lead to failure of an the vehicle with the seat belt or LATCH anchor- infant or child restraint.
Page 79 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 2. Do the child’s knees bend comfortably over the front position. If the shoulder belt contacts the face or neck, of the vehicle seat – while they are still sitting all the move the child closer to the center of the vehicle, or use way back? a booster seat to position the seat belt on the child...
Page 80 78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Recommendations For Attaching Child Restraints Restraint Type Combined Use any attachment method shown with an “X” Below Weight of the LATCH – Seat Belt Only LATCH – Seat Belt + Top Child + Child Lower Anchors Lower Anchors Tether Anchor...
Page 81 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 Lower Anchors And Tethers For Children (LATCH) Your vehicle is equipped with the child restraint anchor- Restraint System age system called LATCH, which stands for Lower Anchors and Tethers for CHildren. The LATCH system has three vehicle anchor points for installing LATCH- equipped child seats.
Page 82 80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH Positions For Installing Child Restraints In This Vehicle Lower Anchorage Symbol 2 anchorages per • seating position Top Tether Anchorage Symbol • I n f o r ma t i o n P r o v i d e d b y :...
Page 83 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 What is the weight limit (child’s 65 lbs (29.5 kg) Use the LATCH anchorage system weight + weight of the child re- until the combined weight of the straint) for using the LATCH an- child and the child restraint is chorage system to attach the child 65 lbs (29.5 kg).
Page 84 82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Can two child restraints be at- Never “share” a LATCH anchorage tached using a common lower with two or more child restraints. LATCH anchorage? If the center position does not have dedicated LATCH lower anchor- ages, use the seat belt to install a child seat in the center position next to a child seat using the...
Page 85 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 Locating LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage sym- bols on the seatback. They are just visible when you lean into the rear seat to install the child restraint.
Page 86 84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Locating Tether Anchorages There are tether strap anchorages behind each rear seating position located in the panel be- tween the rear seatback and the rear window. They are found under a plastic cover with the tether anchorage symbol on it.
Page 87 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 tether strap. The tether strap will have a hook at the end Always follow the directions of the child restraint manu- to attach to the top tether anchorage and a way to tighten facturer when installing your child restraint.
Page 88 86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE forward and rearward in the vehicle, you may wish to 6. Test that the child restraint is installed tightly by move it to its rear-most position to make room for the pulling back and forth on the child seat at the belt child seat.
Page 89 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 Installing Child Restraints Using The Vehicle Seat WARNING! Belt • Improper installation of a child restraint to the The seat belts in the passenger seating positions are LATCH anchorages can lead to failure of the re- equipped with a Switchable Automatic Locking Retractor straint.
Page 90 88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Systems for Installing Child Restraints in this Vehicle • ALR = Switchable Automatic Locking Retractor Top Tether Anchorage Symbol • I n f o r ma t i o n P r o v i d e d b y :...
Page 91 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 What is the weight limit (child’s Weight limit of the Child Restraint Always use the tether anchor when weight + weight of the child re- using the seat belt to install a for- straint) for using the Tether Anchor ward facing child restraint, up to with the seat belt to attach a forward...
Page 92 90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing A Child Restraint With A Switchable 5. To lock the seat belt, pull down on the shoulder part of Automatic Locking Retractor (ALR) the belt until you have pulled all the seat belt webbing out of the retractor.
Page 93 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 strap. See the section “Installing Child Restraints WARNING! (Continued) Using the Top Tether Anchorage” for directions to tether strap of a rear-facing car seat to the tether attach a tether anchor. anchorage that is approved for that seating position, 9.
Page 94 92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage.
Page 95: Transporting Pets
(transmission and axle) in your vehicle. opening between the seatbacks as you remove Drive moderately during the first 300 miles (500 km). slack in the strap. After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.
Page 96: Safety Tips
94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE While cruising, brief full-throttle acceleration within the NOTE: A new engine may consume some oil during its limits of local traffic laws contributes to a good break-in. first few thousand miles (kilometers) of operation. This Wide-open throttle acceleration in low gear can be detri- should be considered a normal part of the break-in and mental and should be avoided.
Page 97: Exhaust Gas
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 WARNING! (Continued) WARNING! (Continued) • It is extremely dangerous to ride in a cargo area, eventually poison you. To avoid breathing (CO), inside or outside of a vehicle. In a collision, people follow these safety tips: riding in these areas are more likely to be seriously •...
Page 98: Safety Checks You Should Make Inside The Vehicle
96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Whenever a change is noticed in the sound of the exhaust Front seat belt assemblies must be replaced after a system, when exhaust fumes can be detected inside the collision. Rear seat belt assemblies must be replaced after vehicle, or when the underside or rear of the vehicle is a collision if they have been damaged (i.e., bent retractor, damaged, have a competent mechanic inspect the com-...
Page 99 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 feel the air directed against the windshield. See your WARNING! (Continued) authorized dealer for service if your defroster is inoper- • Never place or install floor mats or other floor able. coverings in the vehicle that cannot be properly Floor Mat Safety Information secured to prevent them from moving and interfer- ing with the pedals or the ability to control the...
Page 100: Periodic Safety Checks You Should Make Outside The Vehicle
98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE lodged in the tread or sidewall. Inspect the tread for cuts WARNING! (Continued) and cracks. Inspect sidewalls for cuts, cracks, and bulges. • Always make sure that objects cannot fall into the Check the wheel nuts for tightness.
Page 101 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS MIRRORS ......106 ▫ Power Folding Outside Mirrors — If Equipped . .115 ▫...
Page 102 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS ......127 TO OPEN AND CLOSE THE HOOD ..144 ▫...
Page 103 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 ▫ Multifunction Lever ....151 ▫ Windshield Washers ....159 ▫...
Page 104 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ To Resume Speed .....170 ▫ Setting The Following Distance In ACC ..182 ▫...
Page 105 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 ▫ Changing FCW And Active Braking Status..202 ▫ Enabling And Disabling ParkSense® ..219 ▫ FCW Limited Warning ....203 ▫...
Page 106 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Programming A Non-Rolling Code ..232 ▫ Opening Power Shade — Manual Mode ..239 ▫ Canadian/Gate Operator Programming ..233 ▫...
Page 107 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 ▫ Glove Compartment ....249 ▫ Grocery Bag Hooks ....254 ▫...
Page 108: Mirrors
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The Automatic Dimming Mirror feature can be turned MIRRORS on or off using the Uconnect® System. Refer to Automatic Dimming Mirror — If Equipped “Uconnect® Settings” in “Understanding Your Instru- A single ball joint mirror is provided in the vehicle. It is ment Panel”...
Page 109 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 NOTE: The ASSIST and 9–1–1 features operate through • Vehicle Customer Care – Total support for all other the Uconnect® Access service. These buttons will only vehicle issues. operate as long as your Uconnect® Access service is 9-1-1 Call active.
Page 110 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Once a connection between the vehicle and a 9-1-1 NOTE: Once a connection is made between the vehicle’s operator is made, the 9-1-1 Call system may transmit 9-1-1 Call system and the 9-1-1 operator, the 9-1-1 opera- the following important vehicle information to a 9-1-1 tor may be able to open a voice connection with the operator:...
Page 111 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 WARNING! WARNING! (Continued) DURING OR AFTER AN ACCIDENT), THE • If anyone in the vehicle could be in danger (e.g., UCONNECT FEATURES, APPS AND SERVICES, fire or smoke is visible, dangerous road conditions AMONG OTHERS, WILL NOT OPERATE.
Page 112 110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the 9-1-1 Call system detects a malfunction, any of the WARNING! following may occur at the time the malfunction is detected, and at the beginning of each ignition cycle: • Ignoring the Rearview Mirror light could mean you will not have 9-1-1 Call services.
Page 113 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Even if the 9-1-1 Call system is fully functional, factors • Wireless network congestion. beyond FCA US LLC’s control may prevent or stop the • Weather. 9-1-1 Call system operation. These include, but are not limited to, the following factors: •...
Page 114: Outside Mirrors
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! WARNING! To avoid damage to the mirror during cleaning, never Vehicles and other objects seen in the passenger side spray any cleaning solution directly onto the mirror. convex mirror will look smaller and farther away Apply the solution onto a clean cloth and wipe the than they really are.
Page 115: Driver's Automatic Dimming Mirror - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 The fourth LED supplies illuminated entry lighting, Driver’s Automatic Dimming Mirror — If Equipped which turns on in both mirrors when you use the Remote This feature is controlled by the inside automatic dim- Keyless Entry (RKE) transmitter or open any door.
Page 116: Power Mirrors
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE vehicle is shifted out of the REVERSE position. Each stored memory setting will have an associated Tilt Mir- rors in Reverse position. NOTE: The Tilt Mirrors in Reverse feature is not turned on when delivered from the factory. The Tilt Mirrors in Reverse feature can be turned on and off using the Uconnect®...
Page 117: Power Folding Outside Mirrors - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Using the mirror control switch, push on any of the four If the mirrors are in the folded position, and vehicle arrows for the direction that you want the mirror to speed is equal or greater than 10 mph (16 km/h), they move.
Page 118: Slide-On-Rod" And Extender Features Of Sun Visor
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE use the extender feature of the sun visor, grab the extender which is located at the rear of the visor and pull rearward. Illuminated Vanity Mirror “Slide-On-Rod” And Extender Features Of Sun Visor Slide-On-Rod Feature To use the “Slide-On-Rod”...
Page 119: Blind Spot Monitoring (Bsm) - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 BLIND SPOT MONITORING (BSM) — IF EQUIPPED The Blind Spot Monitoring (BSM) system uses two radar- based sensors, located inside the rear bumper fascia, to detect highway licensable vehicles (automobiles, trucks, motorcycles, etc.) that enter the blind spot zones from the rear/front/side of the vehicle.
Page 120 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE both sides of the vehicle when the vehicle speed reaches approximately 6 mph (10 km/h) or higher and will alert the driver of vehicles in these areas. NOTE: • The BSM system does NOT alert the driver about rapidly approaching vehicles that are outside the de- tection zones.
Page 121 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 The area on the rear fascia where the radar sensors are The BSM system notifies the driver of objects in the located must remain free of snow, ice, and dirt/road detection zones by illuminating the BSM warning light contamination so that the BSM system can function located in the outside mirrors in addition to sounding an properly.
Page 122 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Entering From The Side Entering From The Rear Vehicles that move into your adjacent lanes from either Vehicles that come up from behind your vehicle on either side of the vehicle. side and enter the rear detection zone with a relative speed of less than 30 m.p.h.
Page 123 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Overtaking Traffic If you pass another vehicle slowly with a relative speed of less than 15 m.p.h. (24 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated. If the difference in speed between the two vehicles is greater than 15 m.p.h.
Page 124 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Overtaking/Passing Stationary Objects The BSM system will not alert you of objects that are traveling in the opposite direction of the vehicle in adjacent lanes. I n f o r ma t i o n P r o v i d e d b y :...
Page 125: Rear Cross Path
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 WARNING! (Continued) system is not designed to detect pedestrians, bicy- clists, or animals. Even if your vehicle is equipped with the BSM system, always check your vehicle’s mirrors, glance over your shoulder, and use your turn signal before changing lanes.
Page 126 124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In a parking lot situation, oncoming vehicles can be obscured by vehicles parked on either side. If the sensors are blocked by other structures or vehicles, the system will not be able to alert the driver. When RCP is on and the vehicle is in REVERSE, the driver is alerted using both the visual and audible alarms, including reducing the radio volume.
Page 127: Modes Of Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 turn signal is then activated, and it corresponds to an Modes Of Operation alert present on that side of the vehicle, an audible chime Three selectable modes of operation are available in the will also be sounded.
Page 128: General Information
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Blind Spot Alert Off Operation is subject to the following two conditions: When the BSM system is turned off there will be no 1. The device may not cause harmful interference. visual or audible alerts from either the BSM or RCP 2.
Page 129: Seats
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 SEATS Power Seats Seats are a part of the Occupant Restraint System of the On models equipped with power seats, the switch is vehicle. located on the outboard side of the seat near the floor. Use this switch to move the driver’s seat up or down, WARNING! forward or rearward or to recline the seatback.
Page 130 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Adjusting a seat while driving may be dangerous. Moving a seat while driving could result in loss of control which could cause a collision and serious injury or death. • Seats should be adjusted before fastening the seat belts and while the vehicle is parked.
Page 131 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Tilting The Seat Up Or Down CAUTION! The angle of the seat cushion can be adjusted in four Do not place any article under a power seat or directions. Pull upward or push downward on the front impede its ability to move as it may cause damage to or rear of the seat switch, the front or rear of the seat the seat controls.
Page 132: Power Lumbar - If Equipped
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! • Adjusting a seat while driving may be dangerous. Do not place any article under a power seat or Moving a seat while driving could result in loss of impede its ability to move as it may cause damage to control which could cause a collision and serious the seat controls.
Page 133: Heated Seats - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 The front driver and passenger heated seats are operated using the Uconnect® System. WARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater.
Page 134 132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Heated Seats will change from HI to LO, indicating the change. The LO-level setting will turn OFF automatically after ap- The front heated seats control buttons are located within proximately 45 minutes. the climate or controls screen of the touchscreen.
Page 135 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Rear Heated Seats NOTE: On some models, the two outboard seats are equipped • Once a heat setting is selected, heat will be felt within with heated seats. The heated seat switches for these two to five minutes.
Page 136: Front Ventilated Seats - If Equipped
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The engine must be running for the ventilated Front Ventilated Seats — If Equipped seats to operate. Located in the seat cushion and seat back are small fans that draw the air from the passenger compartment and Vehicles Equipped With Remote Start move air through fine perforations in the seat cover to On models that are equipped with remote start, the...
Page 137 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 The RHRs will automatically return to their normal WARNING! position following a rear impact. If the RHRs do not return to their normal position see your authorized The head restraints for all occupants must be prop- dealer immediately.
Page 138 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • A loose head restraint thrown forward in a colli- sion or hard stop could cause serious injury or death to occupants of the vehicle. Always securely stow removed head restraints in a location outside the occupant compartment.
Page 139 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 Rear Head Restraints The center head restraint has two adjustable positions, up or down. When the center seat is being occupied the head restraint should be in the raised position. When there are no occupants in the center seat the head restraint can be lowered for maximum visibility for the driver.
Page 140: Folding Rear Seat
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • The head restraint should only be removed by quali- fied technicians, for service purposes only. If the center rear head restraints requires removal, see your autho- rized dealer. • The outboard head restraints are not adjustable. Folding Rear Seat The rear seatbacks can be folded forward to provide an additional storage area.
Page 141 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 WARNING! • Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position, the seat will not provide the proper sta- bility for child seats and/or passengers. An improp- erly latched seat could cause serious injury.
Page 142: Driver Memory Seat - If Equipped
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The memory seat switch is located on the driver’s door DRIVER MEMORY SEAT — IF EQUIPPED trim panel. The switch consists of three buttons: The (S) This feature allows the driver to store up to two different button, which is used to activate the memory save memory profiles for easy recall through a memory function and the (1) and (2) buttons which are used to...
Page 143: Programming The Memory Feature
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Programming The Memory Feature Linking And Unlinking The Remote Keyless Entry Transmitter To Memory To create a new memory profile, perform the following: Your RKE transmitters can be programmed to recall one 1. Place the ignition into the RUN position. of two pre-programmed memory profiles by pushing the 2.
Page 144: Memory Position Recall
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If a memory profile has not already been set, Memory Position Recall refer to Programming The Memory Feature in this NOTE: The vehicle must be in PARK to recall memory section for instructions on how to set a memory profile. positions.
Page 145: Easy Entry/Exit Seat
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 • The Easy Entry/Easy Exit feature is disabled when the Easy Entry/Exit Seat driver seat position is less than 0.9 in (22.7 mm) This feature provides automatic driver seat positioning to forward of the rear stop. At this position, there is no enhance driver mobility when entering and exiting the benefit to the driver by moving the seat for Easy Exit vehicle.
Page 146: To Open And Close The Hood
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Move to the outside of the vehicle and push the safety TO OPEN AND CLOSE THE HOOD catch to the left. The safety catch is located under the Two latches must be released to open the hood. center front edge of the hood.
Page 147: Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 LIGHTS CAUTION! Headlight Switch To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approxi- The headlight switch is located on the left side of mately 6 inches (15 cm), and then drop it.
Page 148: Automatic Headlights - If Equipped
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels. To turn the system on, rotate the headlight switch counterclockwise to the AUTO position. When the system is on, the headlight time delay feature is also on.
Page 149: Headlight Time Delay
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 is set to ON. In addition, the headlights will turn off If you turn the headlights or parking lights on, or place when the wipers are turned off if they were turned on by the ignition in ACC or RUN, the system will cancel the this feature.
Page 150: Automatic High Beam Headlamp Control - If Equipped
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Broken, muddy, or obstructed headlights and taillights Automatic High Beam Headlamp Control — If of vehicles in the field of view will cause headlights to Equipped remain on longer (closer to the vehicle). Also, dirt, film, The Automatic High Beam Headlamp Control system and other obstructions on the windshield or camera provides increased forward lighting at night by automat-...
Page 151: Adaptive Bi-Xenon High Intensity Discharge Headlights - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 To Deactivate • The Adaptive Headlight System is active only when the vehicle is moving forward. 1. Pull the multifunction lever toward you (or rearward The Adaptive Headlight System can be turned On or Off in car) to manually deactivate the system (normal using the Uconnect®...
Page 152: Lights-On Reminder
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lights-On Reminder If the headlights or parking lights are on after the ignition is placed in the OFF position, a chime will sound to alert the driver when the driver’s door is opened. Fog Lights —...
Page 153: Multifunction Lever
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 NOTE: The fog lights will operate with the low beam headlights or parking lights on. However, selecting the high beam headlights will turn off the fog lights. Multifunction Lever The multifunction lever controls the operation of the turn signals, headlight beam selection and passing lights.
Page 154: Lane Change Assist
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: High/Low Beam Switch Push the multifunction lever away from you to switch • If either light remains on and does not flash, or there is the headlights to high beam. Pull the multifunction lever a very fast flash rate, check for a defective outside light toward you to switch the headlights back to low beam.
Page 155: Front Map/Reading Lights - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 second time. The lights will also turn on when the Front Map/Reading Lights — If Equipped UNLOCK button on the Remote Keyless Entry (RKE) is The front map/reading lights are mounted in the over- pushed.
Page 156: Courtesy Lights
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Courtesy Lights Ambient Light — If Equipped The courtesy lights can be turned on by pushing the top The overhead console is equipped with an ambient light corner of the lens. To turn the lights off, push the lens a feature.
Page 157: Interior Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 Dimmer Controls Interior Lights The interior lights come on when a door is opened. The dimmer control is part of the headlight switch and is located on the left side of the instrument panel. To protect the battery, the interior lights will turn off automatically 10 minutes after the ignition is moved to the LOCK position.
Page 158 156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE With the parking lights or headlights on, rotating the left Ambient Light Control dimmer control upward will increase the brightness of Rotate the right dimmer control upward or downward to the instrument panel lights and lighted cupholders (if increase or decrease the brightness of the door handle equipped).
Page 159: Windshield Wipers And Washers
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 Dome Light Position WINDSHIELD WIPERS AND WASHERS Rotate the left dimmer control completely upward to the The multifunction lever operates the windshield wipers second detent to turn on the interior lights. The interior and washer when the ignition is placed in the ON/RUN lights will remain on when the dimmer control is in this or ACC position.
Page 160: Intermittent Wiper System
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Intermittent Wiper System CAUTION! Use the intermittent wiper when weather conditions • Turn the windshield wipers off when driving make a single wiping cycle with a variable pause be- through an automatic car wash. Damage to the tween cycles desirable.
Page 161: Mist Feature
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 If you activate the washer while the windshield wiper Mist Feature control is in the delay range, the wipers will operate for Rotate the end of the lever downward to the Mist two wipe cycles after releasing the lever and then resume position to activate a single wipe cycle to clear off road the intermittent interval previously selected.
Page 162: Headlights On With Wipers (Available With Automatic Headlights Only)
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE from the windshield washers of the vehicle ahead. Rotate Headlights On With Wipers (Available With the end of the multifunction lever to one of four settings Automatic Headlights Only) to activate this feature. When this feature is active, the headlights will turn on after the wipers are turned on if the headlight switch is The sensitivity of the system can be adjusted with the...
Page 163 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 NOTE: vehicle speed becomes greater than 0 mph (0 km/h) or the outside temperature rises above freezing. • The Rain Sensing feature will not operate when the wiper speed is in the low or high position. •...
Page 164: Tilt/Telescoping Steering Column
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To unlock the steering column, pull the lever downward. TILT/TELESCOPING STEERING COLUMN To tilt the steering column, move the steering wheel This feature allows you to tilt the steering column upward or downward as desired. To lengthen or shorten upward or downward.
Page 165: Power Tilt/Telescoping Steering Column - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 POWER TILT/TELESCOPING STEERING COLUMN — IF EQUIPPED This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The power tilt/telescoping steering column switch is located below the multifunc- tion lever on the steering column.
Page 166: Heated Steering Wheel - If Equipped
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: For vehicles equipped with Driver Memory Seat, HEATED STEERING WHEEL — IF EQUIPPED you can use your Remote Keyless Entry (RKE) transmit- The steering wheel contains a heating element that helps ter or the memory switch on the driver’s door trim panel warm your hands in cold weather.
Page 167 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 NOTE: The engine must be running for the heated WARNING! steering wheel to operate. • Persons who are unable to feel pain to the skin Vehicles Equipped With Remote Start because of advanced age, chronic illness, diabetes, On models that are equipped with remote start, the spinal cord injury, medication, alcohol use, exhaus- heated steering wheel can be programmed to come on...
Page 168: Adjustable Pedals - If Equipped
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ADJUSTABLE PEDALS — IF EQUIPPED The adjustable pedals system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position. This feature allows the brake and accelera- tor pedals to move toward or away from the driver to provide improved position with the steering wheel.
Page 169 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 Push the switch rearward to move the pedals rearward • For vehicles equipped with Driver Memory Seat, you (toward the driver). can use your Remote Keyless Entry (RKE) transmitter or the memory switch on the driver’s door trim panel •...
Page 170: Electronic Speed Control - If Equipped
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not adjust the pedals while the vehicle is moving. You could lose control and have an accident. Always adjust the pedals while the vehicle is parked. ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, the Electronic Speed Control takes over accelerator operations at speeds greater than 25 mph (40 km/h).
Page 171: To Activate
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 NOTE: In order to ensure proper operation, the Elec- WARNING! tronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at Leaving the Electronic Speed Control system on the same time.
Page 172: To Deactivate
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The drivers preferred units can be selected through the To Deactivate instrument panel settings if equipped. Refer to “Under- A soft tap on the brake pedal, pushing the CANCEL standing Your Instrument Panel” for more information. button, or normal brake pressure while slowing the The speed increment shown is dependant on the chosen vehicle will deactivate the Electronic Speed Control with-...
Page 173 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 Metric Speed (km/h) U.S. Speed (mph) • Pushing the SET + button once will result in a 1 km/h • Pushing the SET - button once will result in a 1 mph increase in set speed. Each subsequent tap of the decrease in set speed.
Page 174: To Accelerate For Passing
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Accelerate For Passing WARNING! Push the accelerator as you would normally. When the Electronic Speed Control can be dangerous where the pedal is released, the vehicle will return to the set speed. system cannot maintain a constant speed.
Page 175 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 ACC will allow you to keep cruise control engaged in The Cruise Control system has two control modes: light to moderate traffic conditions without the constant • Adaptive Cruise Control mode for maintaining an need to reset your cruise control.
Page 176 174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) • Cannot take street, traffic, and weather condi- • Adaptive Cruise Control (ACC) is a convenience tions into account, and may be limited upon system. It is not a substitute for active driving adverse sight distance conditions.
Page 177: Adaptive Cruise Control (Acc) Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 WARNING! (Continued) • When driving in fog, heavy rain, heavy snow, sleet, heavy traffic, and complex driving situations (i.e., in highway construction zones). • When entering a turn lane or highway off ramp; when driving on roads that are winding, icy, snow- covered, slippery, or have steep uphill or downhill slopes.
Page 178: Activating Adaptive Cruise Control (Acc)
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Any chassis/suspension or tire size modifications NOTE: You cannot engage ACC under the following to the vehicle will effect the performance of the Adaptive conditions: Cruise Control and Forward Collision Warning System. •...
Page 179: To Activate/Deactivate
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 To turn the system OFF, push and release the Adaptive To Activate/Deactivate Cruise Control (ACC) ON/OFF button again. At this Push and release the Adaptive Cruise Control (ACC) time, the system will turn off and the DID will display ON/OFF button.
Page 180: To Set A Desired Acc Speed
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: ACC cannot be set if there is a stationary vehicle WARNING! in front of your vehicle in close proximity. Leaving the Adaptive Cruise Control (ACC) system Remove your foot from the accelerator pedal. If you do on when not in use is dangerous.
Page 181: To Turn Off
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 • The shift lever/gear selector is removed from the To Turn Off Drive position. The system will turn off and erase the set speed in memory if: • The Electronic Stability Control/Traction Control Sys- tem (ESC/TCS) activates.
Page 182: To Vary The Speed Setting
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: To Vary The Speed Setting To Increase Speed • If your vehicle stays at standstill for longer than two seconds, then the system will cancel and the brake While ACC is set, you can increase the set speed by force will be ramped-out.
Page 183 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 Metric Speed (km/h) U.S. Speed (mph) • Pushing the SET + button once will result in a 1 km/h • Pushing the SET - button once will result in a 1 mph increase in set speed. Each subsequent tap of the decrease in set speed.
Page 184: Setting The Following Distance In Acc
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • The ACC system maintains set speed when driving up hill and down hill. However, a slight speed change on • When you override and push the SET + button or moderate hills is normal. In addition, downshifting SET - buttons, the new Set Speed will be the current may occur while climbing uphill or descending down- speed of the vehicle.
Page 185 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 Distance Setting 4 Bars (Longest) Distance Setting 3 Bars (Long) I n f o r ma t i o n P r o v i d e d b y :...
Page 186 184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Distance Setting 2 Bars (Medium) Distance Setting 1 Bar (Short) To increase the distance setting, push the Distance Setting — Increase button and release. Each time the button is pushed, the distance setting increases by one bar (longer). I n f o r ma t i o n P r o v i d e d b y :...
Page 187 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 To decrease the distance setting, push the Distance Set- • The distance setting is changed. ting — Decrease button and release. Each time the button • The system disengages. (Refer to the information on is pushed, the distance setting decreases by one bar ACC Activation).
Page 188: Overtake Aid
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Overtake Aid When driving with ACC engaged and following a ve- hicle, the system will provide an additional acceleration up to the ACC set speed to assist in passing the vehicle. This additional acceleration is triggered when the driver utilizes the left turn signal and will only be active when passing on the left hand side.
Page 189: Adaptive Cruise Control (Acc) Menu
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 A cancel message will display on the DID and produce a Adaptive Cruise Control (ACC) Menu warning chime. Driver intervention will be required at The DID displays the current ACC system settings. The this moment.
Page 190: Display Warnings And Maintenance
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Push the SET + or the SET- button (located on the steering Display Warnings And Maintenance wheel) and the following will display in the DID: “Wipe Front Radar Sensor In Front Of Vehicle” ACC SET Warning When ACC is set, the set speed will display in the...
Page 191 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 vehicle has left these areas. Under rare conditions, when • Do not remove any screws from the sensor. Doing so the radar is not tracking any vehicles or objects in its path could cause an ACC system malfunction or failure and this warning may temporarily occur.
Page 192 190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: obstructions, such as mud, dirt, or ice on windshield and fog on the inside of glass. In these cases, the DID will • If the “ACC/FCW Unavailable Wipe Front Radar display “ACC/FCW Limited Functionality Clean Front Sensor”...
Page 193: Precautions While Driving With Acc
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 When the condition that created limited functionality is Precautions While Driving With ACC no longer present, the system will return to full function- In certain driving situations, ACC may have detection ality. issues. In these cases, ACC may brake late or unexpect- edly.
Page 194 192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE the vehicle is out of the curve the system will resume your original Set Speed. This is a part of normal ACC system functionality. NOTE: On tight turns ACC performance may be limited. Offset Driving Condition Example Turns And Bends When driving on a curve with ACC engaged, the system...
Page 195 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 Using ACC On Hills Lane Changing When driving on hills, ACC may not detect a vehicle in ACC may not detect a vehicle until it is completely in the your lane. Depending on the speed, vehicle load, traffic lane in which you are traveling.
Page 196 194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Narrow Vehicles Some narrow vehicles traveling near the outer edges of the lane or edging into the lane are not detected until they have moved fully into the lane. There may not be sufficient distance to the vehicle ahead.
Page 197: General Information
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 Stationary Objects And Vehicles General Information ACC does not react to stationary objects and stationary This vehicle has systems that operate on radio frequency vehicles. For example, ACC will not react in situations that comply with Part 15 of the Federal Communications where the vehicle you are following exits your lane and Commission (FCC) rules and with Industry Canada...
Page 198: Normal (Fixed Speed) Electronic Speed Control Mode
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Normal (Fixed Speed) Electronic Speed Control WARNING! Mode In the normal Cruise Control mode, the system will In addition to Adaptive Cruise Control mode, a Normal not react to vehicles ahead. In addition, the proximity (Fixed Speed) Electronic Speed Control mode is available warning does not activate and no alarm will sound for cruising at fixed speeds.
Page 199 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 Once a speed has been set a message (CRUISE CON- U.S. Speed (mph) TROL SET TO MPH/KM) will appear indicating what • Pushing the SET + button once will result in a 1 mph speed was set.
Page 200 198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Decrease Speed Metric Speed (km/h) When the Normal (Fixed Speed) Cruise Control is set, • Pushing the SET - button once will result in a 1 km/h you can decrease speed by pushing the SET - button. decrease in set speed.
Page 201: Forward Collision Warning (Fcw) With Mitigation - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 • The vehicle parking brake is applied. • The Adaptive Cruise Control (ACC) On/Off button is pushed. • The braking temperature exceeds normal range (over- heated). FORWARD COLLISION WARNING (FCW) WITH MITIGATION — IF EQUIPPED •...
Page 202 200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: FCW monitors the information from the forward event stops the vehicle completely, the system will hold looking sensors as well as the Electronic Brake Controller the vehicle at standstill for two seconds and then release (EBC), to calculate the probability of a forward collision.
Page 203: Turning Fcw On Or Off
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 When the system determines a collision with the vehicle be deactivated to prevent unnecessary warnings to the in front of you is no longer probable, the warning surroundings. message will be deactivated. WARNING! NOTE: Forward Collision Warning (FCW) is not intended to •...
Page 204: Changing Fcw And Active Braking Status
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To turn the FCW system OFF, push the forward collision Changing FCW And Active Braking Status button once to turn the system OFF (led turns on). The FCW Sensitivity And Active Braking Settings are To turn the FCW system back ON, push the forward programmable through the Uconnect®...
Page 205: Fcw Limited Warning
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 NOTE: fully available. Once the condition that limited the sys- tem performance is no longer present, the system will • The system will retain the last setting selected by the return to its full performance state. If the problem per- driver after ignition shut down.
Page 206: Turning Lanesense On Or Off
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LaneSense system uses a forward looking camera to remain within the lane. When only a single lane marking detect lane markings and measure vehicle position is detected, a haptic (torque) warning will not be pro- within the lane boundaries.
Page 207: Lanesense Warning Message
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 To turn the LaneSense system OFF, push the LaneSense button once to turn the system OFF (LED turns on). NOTE: The LaneSense system will retain the last system state ON or OFF from the last ignition cycle when the ignition is changed to the ON/RUN position.
Page 208 206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When the LaneSense system senses the lane has been NOTE: The LaneSense system operates with the similar approached and is in a lane departure situation, the behavior for a right lane departure when only the right left thick lane line flashes yellow (on/off), the left thin lane marking has been detected.
Page 209 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 • For example: If approaching the left side of the lane the steering wheel will turn to the right. Lanes Sensed (White Lines/Green Indicator) • When the LaneSense system senses a lane drift situa- tion, the left thick lane line and left thin line turn solid Lane Sensed (Solid Yellow Thick Line, Solid Yellow Thin Line/Solid Yellow Indicator)
Page 210 208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When the LaneSense system senses the lane has been approached and is in a lane departure situation, the left thick lane line flashes yellow (on/off) and the left thin line remains solid yellow. The LaneSense indicator changes from solid yellow to flashing yellow.
Page 211: Changing Lanesense Status
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 • Use of the turn signal suppresses the warnings. Changing LaneSense Status The LaneSense system settings can be configured • The system will not apply torque to the steering wheel through the Uconnect® system screen. whenever a safety system engages.
Page 212: Parksense® Sensors
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ParkSense® can be active only when the gear selector is obstacles from approximately 12 in (30 cm) up to 47 in in REVERSE or DRIVE. If ParkSense® is enabled at one (120 cm) from the front fascia/bumper in the horizontal of these gear selector positions, the system will remain direction, depending on the location, type and orienta- active until the vehicle speed is increased to approxi-...
Page 213: Parksense® Display
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 the display will show the single arc moving closer to the ParkSense® Display vehicle and the tone will change from fast to continuous. Rear Park Assist When the vehicle is in REVERSE, the DID will display the park assist ready system status.
Page 214 212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Slow Tone/Solid Arc Slow Tone/Solid Arc I n f o r ma t i o n P r o v i d e d b y :...
Page 215 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213 Fast Tone/Flashing Arc Fast Tone/Flashing Arc I n f o r ma t i o n P r o v i d e d b y :...
Page 216 214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: Continuous Tone/Flashing Arc I n f o r ma t i o n P r o v i d e d b y :...
Page 217 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215 WARNING ALERTS Rear Dis- Greater than 79-59 in 59-47 in 47-39 in 39-25 in 25-12 in Less than tance 79 in (200-150 cm) (150-120 (120-100 (100-65 (65-30 cm) 12 in (in/cm) (200 cm) (30 cm) Arcs —...
Page 218 216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: ParkSense® will reduce the volume of the radio, If an obstacle is detected in the left and/or right front if on, when the system is sounding an audio tone. region, the display will show a single flashing arc in the left and/or right front region and will produce a fast Front Park Assist sound tone.
Page 219 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217 Fast Tone/Flashing Arc Continuous Tone/Flashing Arc I n f o r ma t i o n P r o v i d e d b y :...
Page 220 218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert opera- tion when the system is detecting an obstacle: WARNING ALERTS Front Distance Greater than...
Page 221: Enabling And Disabling Parksense
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219 Front Park Assist Audible Alerts Enabling And Disabling ParkSense® ParkSense® will turn off the Front Park Assist audible ParkSense® can be enabled and disabled with the alert (chime) after approximately three seconds when an ParkSense®...
Page 222: Service The Parksense® Park Assist System
220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE arc alerts will interrupt the PARKSENSE UNAVAIL- Service The ParkSense® Park Assist System ABLE WIPE REAR SENSORS , PARKSENSE UNAVAIL- During vehicle start up, when the ParkSense® System ABLE WIPE FRONT SENSORS , or PARKSENSE UN- has detected a faulted condition, the instrument cluster AVAILABLE SERVICE REQUIRED messages if an object will actuate a single chime, once per ignition cycle, and it...
Page 223: Cleaning The Parksense® System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 221 • When you move the gear selector to the REVERSE Cleaning The ParkSense® System position and ParkSense® is turned off, the instrument Clean the ParkSense® sensors with water, car wash soap cluster will display “PARKSENSE OFF” for as long as and a soft cloth.
Page 224 222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE system misinterpreting a close object as a sensor WARNING! problem, causing the “PARKSENSE UNAVAILABLE SERVICE REQUIRED” message to be displayed in the • Drivers must be careful when backing up even instrument cluster. when using ParkSense®.
Page 225: Parkview® Rear Back Up Camera - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 223 the shift lever/gear selector is put into REVERSE. The WARNING! (Continued) ParkView® camera is located on the rear of the vehicle • Before using ParkSense®, it is strongly recom- above the rear license plate. The image will be displayed mended that the ball mount and hitch ball assem- in the touchscreen display along with a caution note to bly is disconnected from the vehicle when the...
Page 226 224 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When the Vehicle is shifted out of Reverse (with camera Different colored zones indicate the distance to the rear of delay turned OFF) the rear camera mode is exited and the the vehicle. last touchscreen appears again.
Page 227 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 225 WARNING! CAUTION! Drivers must be careful when backing up even when • To avoid vehicle damage, ParkView® should only using the ParkView® Rear Back Up Camera. Always be used as a parking aid. The ParkView® camera is check carefully behind your vehicle, and be sure to unable to view every obstacle or object in your check for pedestrians, animals, other vehicles, ob-...
Page 228: Overhead Console
226 UNDERSTANDING THE FEATURES OF YOUR VEHICLE OVERHEAD CONSOLE Front Map/Reading Lights — If Equipped The overhead console contains courtesy/reading lights Lights are mounted in the overhead console. Each light and storage for sunglasses. Universal Garage Door can be turned on by pushing the switch on either side of Opener (HomeLink®) and power sunroof switches may the console.
Page 229: Courtesy Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 227 To turn the lights off, push the switch a second time. The Courtesy Lights lights also turn on when a door is opened. The lights will The courtesy lights can be turned on by pushing the top also turn on when the UNLOCK button on the RKE is corner of the lens.
Page 230: Sunglasses Bin Door
228 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunglasses Bin Door GARAGE DOOR OPENER — IF EQUIPPED At the front of the console a compartment is provided for HomeLink® replaces up to three hand-held transmitters the storage of a pair of sunglasses. The storage compart- that operate devices such as garage door openers, motor- ment access is a “push/push”...
Page 231: Before You Begin Programming Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 229 For more efficient programming and accurate transmis- sion of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the device that is being programmed to the HomeLink® system.
Page 232: Programming A Rolling Code
230 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming A Rolling Code For programming garage door openers that were manu- factured after 1995. These garage door openers can be identified by the “LEARN” or “TRAIN” button located where the hanging antenna is attached to the garage door opener.
Page 233 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 231 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 Firmly push and release the “LEARN” or “TRAIN- cm) away from the HomeLink® button you wish to ING” button. On some garage door openers/devices program while keeping the HomeLink®...
Page 234: Programming A Non-Rolling Code
232 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reprogramming A Single HomeLink® Button 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 (Rolling Code) cm) away from the HomeLink® button you wish to program while keeping the HomeLink® indicator To reprogram a channel that has been previously trained, light in view.
Page 235: Canadian/Gate Operator Programming
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 233 • To program the two remaining HomeLink® buttons, Canadian/Gate Operator Programming repeat each step for each remaining button. DO NOT For programming transmitters in Canada/United States erase the channels. that require the transmitter signals to “time-out” after several seconds of transmission.
Page 236 234 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 • If the indicator light stays on constantly, program- cm) away from the HomeLink® button you wish to ming is complete and the garage door/device should program while keeping the HomeLink®...
Page 237: Using Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 235 3. Without releasing button proceed with The HomeLink® Universal Transceiver is disabled when “Canadian/Gate Operator Programming” step 2 and the Vehicle Security Alarm is active. follow all remaining steps. Troubleshooting Tips Using HomeLink® If you are having trouble programming HomeLink®, To operate, push and release the programmed here are some of the most common solutions:...
Page 238: General Information
236 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information WARNING! This device complies with FCC rules Part 15 and Industry • Vehicle exhaust contains carbon monoxide, a dan- Canada RSS-210. Operation is subject to the following gerous gas. Do not run your vehicle in the garage two conditions: while programming the transceiver.
Page 239: Commandview® Sunroof With Power Shade - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 237 COMMANDVIEW® SUNROOF WITH POWER SHADE — IF EQUIPPED The CommandView® sunroof switch is located to the left between the sun visors on the overhead console. The power shade switch is located to the right between the sun visors on the overhead console.
Page 240: Opening Sunroof - Express
238 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) • Do not allow small children to operate the sunroof. • Never leave children unattended in a vehicle, or Never allow your fingers, other body parts, or any with access to an unlocked vehicle. Never leave the object, to project through the sunroof opening.
Page 241: Closing Sunroof - Express
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 239 movement. The sunroof and sunshade will remain in a Opening Power Shade — Express partially opened condition until the switch is pushed and Push the shade switch rearward and release it within held rearward again. one-half second and the shade will automatically open to the halfway position and stop automatically.
Page 242: Closing Power Shade - Express
240 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Closing Power Shade — Express Venting Sunroof — Express Push the switch forward and release it within one-half Push and release the Vent button within one-half sec- second and the shade will close automatically from any ond and the sunroof will open to the vent position.
Page 243: Wind Buffeting
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 241 NOTE: If three consecutive sunroof close attempts result Ignition OFF Operation in Pinch Protect reversals, the fourth close attempt will be The power sunroof switch will remain active for up to a Manual Close movement with Pinch Protect disabled. approximately ten minutes after the ignition switch is turned to the LOCK position.
Page 244 242 UNDERSTANDING THE FEATURES OF YOUR VEHICLE with a “key” are powered when the ignition switch is in the ON or ACC position, while the outlets labeled with a “battery” are connected directly to the battery and pow- ered at all times. NOTE: •...
Page 245 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 243 In addition to the front power outlet, there is also a power NOTE: If the Media Hub is in use, do not exceed the outlet located in the storage area of the center console. maximum power of 100 Watts (8 Amps) for the center console power outlet.
Page 246 244 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The instrument panel power outlet and dual rear console USB ports can be changed to “battery” powered all the time by moving the #12 20 Amp fuse from “IGN” to “B+”. Refer to “Rear Power Distribution Center Cover”...
Page 247 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 245 CAUTION! CAUTION! (Continued) • After the use of high power draw accessories or • Many accessories that can be plugged in draw long periods of the vehicle not being started (with power from the vehicle’s battery even when not in accessories still plugged in), the vehicle must be use (i.e., cellular phones, etc.).
Page 248: Cupholders
246 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUPHOLDERS Front Seat Cupholders The cupholders are located in the forward edge of the center console. Front Cupholders Heated And Cooled Cupholders — If Equipped Your vehicle may be equipped with heated and cooled cupholders.
Page 249: Rear Seat Cupholders
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 247 WARNING! When using the cupholder in the “Hot” position, avoid contact with the heated portion of the cup- holder in order to reduce the possibility of burns. Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injuries, medication, alcohol use, exhaus- tion or other physical condition must exercise par-...
Page 250 248 UNDERSTANDING THE FEATURES OF YOUR VEHICLE convenient access to beverage cans or bottles while Lighted Cupholders — If Equipped maintaining a resting place for the rear occupant’s el- On some vehicles the rear cupholders are equipped with bows. a light ring that illuminates the cupholders for the rear passengers.
Page 251: Storage
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 249 STORAGE Console Features There is a cubby bin located forward of the gear selector. Glove Compartment The cubby bin is covered with a push-push actuated The glove compartment is located on the passenger side door.
Page 252 250 UNDERSTANDING THE FEATURES OF YOUR VEHICLE small items like an ipod or phone. Below the upper tray, the lower storage compartment is made for larger items, like CDs and tissue boxes. In addition, the 12 volt power outlet, USB and Aux jack are located here. Center Console Inside the center console armrest, there is a removable upper storage tray that can be slid forward/rearward on...
Page 253: Door Storage
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 251 Door Storage WARNING! The door panels contain storage areas. Do not operate this vehicle with a console compart- ment lid in the open position. Driving with the console compartment lid open may result in injury in a collision.
Page 254: Rear Seat Armrest Storage - If Equipped
252 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Seat Armrest Storage — If Equipped Cargo Area — Vehicles Equipped With 60/40 Split-Folding Rear Seat For rear passengers there is a storage bin located in the armrest. Lift upward on the latch to open the storage The 60/40 split-folding rear seat provides cargo-carrying compartment.
Page 255 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 253 WARNING! WARNING! The weight and position of cargo and passengers can • Be certain that the seatback is securely locked into change the vehicle center of gravity and vehicle position. If the seatback is not securely locked into handling.
Page 256: Cargo Area Features
254 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CARGO AREA FEATURES Trunk Mat — If Equipped A trunk mat covers the bottom of the cargo area. The trunk mat is used to protect the interior of the trunk from mud, snow, and debris. Grocery Bag Hooks The rear cargo area is equipped with grocery bag hooks, located on either side of the rear cargo area.
Page 257: Cargo Net
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 255 Cargo Net REAR WINDOW FEATURES The rear cargo area is equipped with a cargo net. Rear Window Defroster The rear window defroster button is located on the climate control. Push this button to turn on the rear window defroster and the heated outside mirrors (if equipped).
Page 258: Power Sunshade - If Equipped
256 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Sunshade — If Equipped CAUTION! Your vehicle may be equipped with a power sunshade Failure to follow these cautions can cause damage to that will reduce the amount of sunlight that will shine the heating elements: through the rear windshield.
Page 259: Load Leveling System - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 257 The power sunshade can also be operated by passengers LOAD LEVELING SYSTEM — IF EQUIPPED in the rears seats. The power sunshade switch is located The automatic load leveling system will provide a level- on the back of the center console between the heated seat riding vehicle under most passenger and cargo loading switches.
Page 260 I n f o r ma t i o n P r o v i d e d b y :...
Page 261 Uconnect® RADIOS — IF EQUIPPED ..299 INSTRUMENT CLUSTER DESCRIPTIONS ..263 iPod®/USB/MP3 CONTROL ....300 DRIVER INFORMATION DISPLAY (DID) ..272 STEERING WHEEL AUDIO CONTROLS .
Page 262 260 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Dual Zone Automatic Climate Controls With ▫ Voice Text Reply ..... .322 Touchscreen ......304 ▫...
Page 263: Instrument Panel Features
UNDERSTANDING YOUR INSTRUMENT PANEL 261 INSTRUMENT PANEL FEATURES 1 — Air Outlet 7 — Glove Compartment 13 — Headlight Switch 2 — Driver Information Display (DID) Con- 8 — Uconnect® System Hard Controls 14 — Adaptive Cruise Control trols 3 — Driver Information Display (DID) 9 —...
Page 264: Instrument Cluster
262 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER I n f o r ma t i o n P r o v i d e d b y :...
Page 265: Instrument Cluster Descriptions
UNDERSTANDING YOUR INSTRUMENT PANEL 263 If the light remains on when the parking brake has been INSTRUMENT CLUSTER DESCRIPTIONS disengaged, and the fluid level is at the full mark on the 1. Tachometer master cylinder reservoir, it indicates a possible brake This gauge measures engine revolutions-per-minute hydraulic system malfunction or that a problem with the (RPM x 1000).
Page 266 264 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The light may flash momentarily during sharp Operation of the Brake Warning Light can be checked by cornering maneuvers, which change fluid level condi- turning the ignition switch from the OFF position to the tions.
Page 267 UNDERSTANDING YOUR INSTRUMENT PANEL 265 dealer as soon as possible. Refer to “Occupant Restraints” the repair/service, so that you can be sure that it is in “Things To Know Before Starting Your Vehicle” for properly reset, or that the door jamb sticker is accurate if further information.
Page 268 266 UNDERSTANDING YOUR INSTRUMENT PANEL 8. Tire Pressure Monitoring Telltale Light — If Equipped reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Each tire, including the spare (if provided), Please note that the TPMS is not a substitute for proper should be checked monthly when cold and tire maintenance, and it is the driver’s responsibility to inflated to the inflation pressure recommended...
Page 269 UNDERSTANDING YOUR INSTRUMENT PANEL 267 alternate tires or wheels on the vehicle that prevent the CAUTION! (Continued) TPMS from functioning properly. Always check the sensor to become inoperable. After using an after- TPMS malfunction telltale after replacing one or more market tire sealant it is recommended that you take tires or wheels on your vehicle, to ensure that the your vehicle to an authorized dealership to have your...
Page 270 268 UNDERSTANDING YOUR INSTRUMENT PANEL 11. Electronic Stability Control (ESC) Activation/ NOTE: Malfunction Indicator Light — If Equipped • The “ESC Off Indicator Light” and the “ESC Activation/Malfunction Indicator Light” come on The “ESC Activation/Malfunction Indicator momentarily each time the ignition switch is turned Light”...
Page 271 UNDERSTANDING YOUR INSTRUMENT PANEL 269 on, a continuous chime will sound to alert you to turn the If the ABS light is on, the brake system should be serviced signals off. If either indicator flashes at a rapid rate, check as soon as possible to restore the benefits of Anti-Lock for a defective outside light bulb.
Page 272 270 UNDERSTANDING YOUR INSTRUMENT PANEL The gauge pointer will likely indicate a higher tempera- WARNING! ture when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to A hot engine cooling system is dangerous. You or exceed the upper limits of the normal operating range.
Page 273 UNDERSTANDING YOUR INSTRUMENT PANEL 271 19. Vehicle Security Light — If Equipped CAUTION! This light will flash at a fast rate for approxi- Prolonged driving with the Malfunction Indicator mately 15 seconds, when the vehicle security Light (MIL) on could cause damage to the engine alarm is arming, and then will flash slowly control system.
Page 274: Driver Information Display (Did)
272 UNDERSTANDING YOUR INSTRUMENT PANEL The system allows the driver to select information by DRIVER INFORMATION DISPLAY (DID) pushing the following buttons mounted on the steering The Driver Information Display (DID) features an inter- wheel: active display which is located in the instrument cluster. This system conveniently allows the driver to select a variety of useful information by pushing the arrow buttons located on the left side of the steering wheel.
Page 275 UNDERSTANDING YOUR INSTRUMENT PANEL 273 Up And Down Arrow Buttons: NOTE: Using the Up or Down arrows allows you to • Holding the Up/Down or Left/Right arrow buttons cycles through the Main Menu Items. will loop the user through the currently selected menu or options presented on the screen.
Page 276: Engine Oil Life Reset
274 UNDERSTANDING YOUR INSTRUMENT PANEL • Within each submenu layer, the up/down arrows will chime has sounded, to indicate the next scheduled oil allow the user to select the item of interest. change interval. The engine oil change indicator system is duty cycle based, which means the engine oil change •...
Page 277 UNDERSTANDING YOUR INSTRUMENT PANEL 275 Speedometer Driver Assist Push and release the OK button to toggle between MPH Fuel Economy and km/h. Push and release the UP or DOWN arrow button until Vehicle Info the Fuel Economy Menu item is highlighted in the DID. The Vehicle Info consists of the following sub menu: •...
Page 278 276 UNDERSTANDING YOUR INSTRUMENT PANEL Trip Info Stored Messages Push and release the UP or DOWN arrow button until Push and release the UP or DOWN arrow button until the Trip Menu item is highlighted in the DID (Toggle left the Messages Menu item is highlighted in the DID.
Page 279: Setting The Analog Clock
UNDERSTANDING YOUR INSTRUMENT PANEL 277 SETTING THE ANALOG CLOCK Uconnect® SETTINGS To set the analog clock at the top center of the instrument The Uconnect® system uses a combination of buttons on panel, push and hold the button until the setting is the touchscreen and buttons on the faceplate located on correct.
Page 280: Buttons On The Faceplate
278 UNDERSTANDING YOUR INSTRUMENT PANEL Buttons On The Faceplate Buttons on the faceplate are located below the Uconnect® system in the center of the instrument panel. In addition, there is a Scroll/Enter control knob located on the right side. Turn the control knob to scroll through menus and change settings (i.e., 30, 60, 90), push the center of the control knob one or more times to select or change a setting (i.e., ON, OFF).
Page 281: Buttons On The Touchscreen
UNDERSTANDING YOUR INSTRUMENT PANEL 279 Engine Options, Audio, Phone/Bluetooth®, Buttons On The Touchscreen SiriusXM Setup, Restore Settings, Clear Personal Data Buttons on the touchscreen are accessible on the and System Information. Uconnect® Touchscreen. NOTE: CAUTION! • Only one touchscreen area may be selected at a time. Do not attach any object to touchscreen, doing so can •...
Page 282 280 UNDERSTANDING YOUR INSTRUMENT PANEL the touchscreen to close out of the settings screen. Press- • Display Brightness With Headlights ON ing the Up or Down Arrow button on the right side of the When in this display, you may select the brightness with screen will allow you to toggle up or down through the the headlights on.
Page 283 UNDERSTANDING YOUR INSTRUMENT PANEL 281 NOTE: To make changes to the Display Brightness with appears next to the language, showing that setting has Headlights OFF setting, the headlights must be off and been selected. Press the back arrow button on the touch- the interior dimmer switch must not be in the party or screen to return to the previous menu.
Page 284 282 UNDERSTANDING YOUR INSTRUMENT PANEL appears next to the setting, showing that setting has been Units selected. Press the back arrow button on the touchscreen After pressing the “Units” button on the touchscreen you to return to the previous menu. may select each unit of measure independently displayed •...
Page 285 UNDERSTANDING YOUR INSTRUMENT PANEL 283 • Temperature • Show Command List Select from: “°C,” or “°F.” When in this display, you may change the Show Com- mand List settings. To change the Show Command List After the desired setting has been selected, press the back settings, press the “Always,”...
Page 286 284 UNDERSTANDING YOUR INSTRUMENT PANEL setting has been selected. Press the back arrow button on • Time Format the touchscreen to return to the previous menu. This feature will allow you to select the time format • Set Time Hours display setting.
Page 287 UNDERSTANDING YOUR INSTRUMENT PANEL 285 Safety & Driving Assistance For further information, refer to “Adaptive Cruise Con- trol (ACC)” in “Understanding The Features Of Your After pressing the “Safety & Driving Assistance” button Vehicle”. on the touchscreen the following settings will be avail- able: •...
Page 288 286 UNDERSTANDING YOUR INSTRUMENT PANEL • LaneSense Warning — If Equipped For further information, refer to “Lane Departure Warn- ing (LDW)” in “Understanding The Features Of Your When this feature is selected, it sets the distance at which Vehicle”. the steering wheel will provide feedback for potential •...
Page 289 UNDERSTANDING YOUR INSTRUMENT PANEL 287 • ParkSense® on the touchscreen, until a check-mark appears next to setting, indicating that the setting had been selected. The ParkSense® system will scan for objects behind the Press the back arrow button on the touchscreen to return vehicle when the transmission shift lever is in REVERSE to the previous menu.
Page 290 288 UNDERSTANDING YOUR INSTRUMENT PANEL • Tilt Side Mirrors In Reverse When “Lights & Chime” mode is activated, the Blind Spot Monitor (BSM) will show a visual alert in the When this feature is selected, the exterior sideview exterior mirrors as well as an audible alert when the turn mirrors will tilt downward when the ignition is in the signal is on.
Page 291 UNDERSTANDING YOUR INSTRUMENT PANEL 289 display whenever the shift lever is put into REVERSE. 8 mph (12 km/h), the transmission is shifted into The image will be displayed on the radio touchscreen “PARK” or the ignition is switched to the OFF position. display along with a caution note to “check entire sur- To set the ParkView®...
Page 292 290 UNDERSTANDING YOUR INSTRUMENT PANEL • Hill Start Assist — If Equipped your desired time interval, and choose either 0 sec, 30 sec, 60 sec or 90 seconds. Press the back arrow button on the When this feature is selected, the Hill Start Assist (HSA) touchscreen to return to the previous menu, or push the system is active.
Page 293 UNDERSTANDING YOUR INSTRUMENT PANEL 291 turned off if they were turned on by this feature. To make • Daytime Running Lights — If Equipped your selection, press the “Headlights With Wipers” but- When this feature is selected, the headlights will turn on ton on the touchscreen, until a check-mark appears next whenever the engine is running.
Page 294 292 UNDERSTANDING YOUR INSTRUMENT PANEL selected. Press the back arrow button on the touchscreen • Flash Lights With Lock to return to the previous menu, or push the back button When this feature is selected, the exterior lights will flash on the faceplate.
Page 295 UNDERSTANDING YOUR INSTRUMENT PANEL 293 • Sound Horn With Remote Start NOTE: If the vehicle is programmed 1st Press Of Key Fob Unlocks “All Doors,” all doors will unlock no matter When this feature is selected, the horn will sound when which Passive Entry equipped door handle is grasped.
Page 296 294 UNDERSTANDING YOUR INSTRUMENT PANEL setting, showing that the setting has been selected. Press NOTE: The seat will return to the memorized seat the back arrow button on the touchscreen to return to the location (if Recall Memory with Remote Key Unlock is set previous menu.
Page 297 UNDERSTANDING YOUR INSTRUMENT PANEL 295 Vehicle Start” button to select from “Off,” “Remote Start” • Engine Off Power Delay or “All Starts” until a check-mark appears next to setting, When this feature is selected, the power window showing that setting has been selected. Press the back switches, radio, Uconnect®...
Page 298 296 UNDERSTANDING YOUR INSTRUMENT PANEL press the “+” or “–” button on the touchscreen to select your the scale between the “+” and “–” buttons on the desired time interval. Press the back arrow button on the touchscreen. Press the back arrow button on the touch- touchscreen to return to the previous menu.
Page 299 UNDERSTANDING YOUR INSTRUMENT PANEL 297 button on the touchscreen, select “On” or “Off.” Press the Phone/Bluetooth® back arrow button on the touchscreen to return to the After pressing the “Phone/Bluetooth®” button on the previous menu. touchscreen the following settings will be available: •...
Page 300 298 UNDERSTANDING YOUR INSTRUMENT PANEL SiriusXM Setup — If Equipped Press the “Subscription Info” button on the touchscreen to access the Subscription Information screen. After pressing the “SiriusXM Setup” button on the touch- screen, the following settings will be available: Write down the SIRIUS ID numbers for your receiver.
Page 301: Uconnect® Radios - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 299 select “Yes” to restore, or “Cancel” to exit. Once the System Information settings are restored, a pop up appears stating settings After pressing the “System Information” button on the reset to default. Press the okay button on the touchscreen touchscreen the following information will be available: to exit.
Page 302: Ipod®/Usb/Mp3 Control
300 UNDERSTANDING YOUR INSTRUMENT PANEL iPod®/USB/MP3 CONTROL This feature allows an iPod® or an external USB device to be plugged into the USB port. iPod® control supports Mini, 4G, Photo, Nano, 5G iPod® and iPhone® devices. Some iPod® software versions may not fully support the iPod®...
Page 303: Steering Wheel Audio Controls
UNDERSTANDING YOUR INSTRUMENT PANEL 301 STEERING WHEEL AUDIO CONTROLS The remote sound system controls are located on the rear surface of the steering wheel at the three and nine o’clock positions. Rear USB Charging Ports The USB “Charge Only” ports will recharge battery operated USB devices when connected.
Page 304: Radio Operation
302 UNDERSTANDING YOUR INSTRUMENT PANEL The right-hand control is a rocker-type switch with a The button located in the center of the left-hand control push-button in the center and controls the volume and will tune to the next preset station that you have pro- mode of the sound system.
Page 305: Radio Operation And Mobile Phones
UNDERSTANDING YOUR INSTRUMENT PANEL 303 6. Do not expose the disc to direct sunlight. antenna, it is recommended that the radio volume be turned down or off during mobile phone operation when 7. Do not store the disc where temperatures may become not using Uconnect®...
Page 306: Dual Zone Automatic Climate Controls With
304 UNDERSTANDING YOUR INSTRUMENT PANEL Buttons On The Touchscreen Dual Zone Automatic Climate Controls With Touchscreen Buttons on the touchscreen are accessible on the Buttons On The Faceplate Uconnect® system screen. The buttons on the faceplate are located below the Uconnect®...
Page 307 UNDERSTANDING YOUR INSTRUMENT PANEL 305 Button Descriptions (Applies To Both Buttons On The 4. AUTO Operation Button Faceplate And Buttons On The Touchscreen) Automatically controls the interior cabin temperature by 1. MAX A/C Button adjusting airflow distribution and amount. Performing this function will cause the system to switch between Press and release to change the current setting, the manual mode and automatic modes.
Page 308 306 UNDERSTANDING YOUR INSTRUMENT PANEL 6. Rear Defrost Button CAUTION! (Continued) Press and release this button to turn on the rear window • Do not use scrapers, sharp instruments, or abrasive defroster and the heated outside mirrors (if equipped). window cleaners on the interior surface of the An indicator will illuminate when the rear window window.
Page 309 UNDERSTANDING YOUR INSTRUMENT PANEL 307 8. Passenger Temperature Control Down Button 10. Blower Control Provides the passenger with independent temperature Blower control is used to regulate the amount of air control. Push the button on the faceplate for cooler forced through the climate system. There are seven temperature settings or on the touchscreen, press and blower speeds available.
Page 310 308 UNDERSTANDING YOUR INSTRUMENT PANEL Button On The Touchscreen direction. There is a shut off wheel located below the air vanes to shut off or adjust the amount of airflow Use the small blower icon to reduce the blower setting from these outlets.
Page 311: Climate Control Functions
UNDERSTANDING YOUR INSTRUMENT PANEL 309 • Mix Mode 14. Driver Temperature Control Up Button Air comes from the floor, defrost and side Provides the driver with independent temperature con- window demist outlets. This mode works best trol. Push the button on the faceplate for warmer tem- in cold or snowy conditions.
Page 312 310 UNDERSTANDING YOUR INSTRUMENT PANEL adjust the blower and airflow mode settings. Also, make Press and release to toggle between MAX A/C and the sure to select only Panel, Bi-Level or Floor modes. prior settings. The button illuminates when MAX A/C is NOTE: In MAX A/C, the blower level and mode position can be •...
Page 313: Automatic Temperature Control (Atc)
UNDERSTANDING YOUR INSTRUMENT PANEL 311 NOTE: In cold weather, use of recirculation mode may 2. Next, adjust the temperature you would like the lead to excessive window fogging. The recirculation system to maintain by adjusting the driver and pas- feature may be unavailable (button on the touchscreen senger temperature control buttons.
Page 314: Operating Tips
312 UNDERSTANDING YOUR INSTRUMENT PANEL To provide you with maximum comfort in the Automatic The operator can also select the direction of the airflow mode, during cold start-ups the blower fan will remain by selecting one of the available mode settings. A/C on low until the engine warms up.
Page 315 A solution of 50% OAT (Organic Additive Technology) fresh air and high blower setting. This will ensure coolant that meets the requirements of Chrysler Material adequate system lubrication to minimize the possibility Standard MS.90032 and 50% water is recommended.
Page 316 314 UNDERSTANDING YOUR INSTRUMENT PANEL Window Fogging Outside Air Intake Interior fogging on the windshield can be quickly re- Make sure the air intake, located directly in front of the moved by turning the mode selector to Defrost. The windshield, is free of obstructions such as leaves. Leaves Defrost/Floor mode can be used to maintain a clear collected in the air intake may reduce airflow, and if they windshield and provide sufficient heating.
Page 317 UNDERSTANDING YOUR INSTRUMENT PANEL 315 Manual Control Setting Suggestions for Various Weather Conditions I n f o r ma t i o n P r o v i d e d b y :...
Page 318: Uconnect® Voice Recognition Quick Tips
316 UNDERSTANDING YOUR INSTRUMENT PANEL Uconnect® VOICE RECOGNITION QUICK TIPS Introducing Uconnect® Start using Uconnect® Voice Recognition with these helpful quick tips. It provides the key Voice Commands and tips you need to know to control your Uconnect® 5.0 or 8.4A/8.4AN system. Uconnect®...
Page 319: Get Started
UNDERSTANDING YOUR INSTRUMENT PANEL 317 Get Started All you need to control your Uconnect® system with your voice are the buttons on your steering wheel. 1. Visit UconnectPhone.com to check mobile device and feature compatibility and to find phone pairing instructions.
Page 320: Basic Voice Commands
318 UNDERSTANDING YOUR INSTRUMENT PANEL Basic Voice Commands The basic Voice Commands below can be given at any point while using your Uconnect® system. Push the VR button . After the beep, say: • Cancel to stop a current voice session •...
Page 321: Radio
UNDERSTANDING YOUR INSTRUMENT PANEL 319 Radio Use your voice to quickly get to the AM, FM or SiriusXM Satellite Radio stations you would like to hear. (Subscrip- tion or included SiriusXM Satellite Radio trial required.) Push the VR button . After the beep, say: •...
Page 322: Media
320 UNDERSTANDING YOUR INSTRUMENT PANEL TIP: Press the Browse button on the touchscreen to see all Media of the music on your iPod® or USB device. Your Voice Uconnect® offers connections via USB, SD, Bluetooth® Command must match exactly how the artist, album, and auxiliary ports (If Equipped).
Page 323: Phone
UNDERSTANDING YOUR INSTRUMENT PANEL 321 TIP: When providing a Voice Command, push the Phone Phone button and say “Call,” then pronounce the name Making and answering hands-free phone calls is easy exactly as it appears in your phone book. When a with Uconnect®.
Page 324: Voice Text Reply
322 UNDERSTANDING YOUR INSTRUMENT PANEL Voice Text Reply PRE-DEFINED VOICE TEXT REPLY RESPONSES Uconnect® will announce incoming text messages. Push Yes. Stuck in Traffic. See you later. the Phone button and say Listen. (Must have com- Start without I’ll be Late. patible mobile phone paired to Uconnect®...
Page 325: Climate (8.4A/8.4An)
UNDERSTANDING YOUR INSTRUMENT PANEL 323 Climate (8.4A/8.4AN) Too hot? Too cold? Adjust vehicle temperatures hands- free and keep everyone comfortable while you keep moving ahead. (If vehicle is equipped with climate control.) Push the VR button . After the beep, say one of the following commands: •...
Page 326: Navigation (8.4A/8.4An)
. After the beep, say: • For the 8.4A Uconnect® System, say: “Enter state.” • For the 8.4AN Uconnect® System, say: “Navigate to 800 Chrysler Drive Auburn Hills, Michigan.” Uconnect® 8.4A/8.4AN Navigation Uconnect® Access (8.4A/8.4AN) 2. Then follow the system prompts.
Page 327: Register (8.4A/8.4An)
UNDERSTANDING YOUR INSTRUMENT PANEL 325 press the Apps button on the 8.4-inch touchscreen to get Roadside Assistance Call started. Detailed registration instructions can be found Wi-Fi Hotspot*** on the next page. **If vehicle is equipped. NOTE: Uconnect® Access is available only on equipped ***Extra charges apply.
Page 328: Mobile App (8.4A/8.4An)
326 UNDERSTANDING YOUR INSTRUMENT PANEL 5. Click on the link inside the email within 72 hours and Mobile App (8.4A/8.4AN) complete the easy online registration process to create Securely link your mobile device to your vehicle with the a personal Mopar® Owner Connect account linked to Uconnect®...
Page 329: Voice Texting (8.4A/8.4An)
UNDERSTANDING YOUR INSTRUMENT PANEL 327 Download the Uconnect® Access App to a compatible 2. Listen to the prompt. After the beep, dictate the Apple® or Android® mobile devices. All you need to do message you would like to send. Wait for Uconnect® to process your message.
Page 330: Yelp® (8.4A/8.4An)
328 UNDERSTANDING YOUR INSTRUMENT PANEL TIP: Once you perform a search, you can reorganize the Yelp® (8.4A/8.4AN) results by selecting either the Best Match, Rating or Once registered with Uconnect® Access, you can use Distance tab on the top of the touchscreen display. your voice to search for the most popular places or things around you.
Page 331: Siriusxm Travel Link™ (8.4A/8.4An)
UNDERSTANDING YOUR INSTRUMENT PANEL 329 SiriusXM Travel Link™ (8.4A/8.4AN) Need to find a gas station, view local movie listings, check a sports score or the 5 - day weather forecast? SiriusXM Travel Link™ is a suite of services that brings a wealth of information right to your Uconnect®...
Page 332: General Information
330 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: General Information This device complies with FCC rules Part 15 and Industry • The transmitter has been tested and it complies with FCC Canada RSS-210. Operation is subject to the following and IC rules. Changes or modifications not expressly two conditions: approved by the party responsible for compliance could void the user’s authority to operate the device.
Page 333: Additional Information
UNDERSTANDING YOUR INSTRUMENT PANEL 331 Uconnect® System Support: Additional Information © 2015 FCA US LLC. All rights reserved. Mopar and • U.S. residents call 1-877-855-8400 visit Uconnect are registered trademarks and Mopar Owner DriveUconnect.com Connect is a trademark of FCA US LLC. Android is a •...
Page 334 I n f o r ma t i o n P r o v i d e d b y :...
Page 335 STARTING AND OPERATING CONTENTS STARTING PROCEDURES ....337 ▫ Key Ignition Park Interlock....344 ▫...
Page 336 334 STARTING AND OPERATING ▫ Shallow Standing Water ....357 ▫ Rain Brake Support ....373 ELECTRIC POWER STEERING .
Page 337 STARTING AND OPERATING 335 ▫ Radial Ply Tires ..... .390 ▫ General Information ....412 ▫...
Page 338 336 STARTING AND OPERATING ▫ E-85 General Information ....417 ▫ Gross Axle Weight Rating (GAWR) ..425 ▫ Ethanol Fuel (E-85) ....418 ▫...
Page 339: Starting Procedures
STARTING AND OPERATING 337 STARTING PROCEDURES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust the • Do not leave the Key Fob in or near the vehicle (or inside and outside mirrors, fasten your seat belt, and if in a location accessible to children), and do not present, instruct all other occupants to buckle their seat leave the ignition (of a vehicle equipped with...
Page 340: Keyless Enter-N-Go
338 STARTING AND OPERATING Keyless Enter-N-Go™ CAUTION! Damage to the transmission may occur if the follow- This feature allows the driver to oper- ing precautions are not observed: ate the ignition switch with the push • Do not shift from REVERSE, PARK, or NEUTRAL of a button, as long as the Remote into any forward gear when the engine is above Start/Keyless Enter-N-Go™...
Page 341 STARTING AND OPERATING 339 4. If you wish to stop the cranking of the engine prior to position. If the shift lever/gear selector is not in PARK the engine starting, push the button again. and the ENGINE START/STOP button is pushed once, the DID will display a “Vehicle Not In Park”...
Page 342: Extreme Cold Weather
340 STARTING AND OPERATING To change the ignition switch positions without starting If Engine Fails To Start the vehicle and use the accessories follow these steps: WARNING! 1. Starting with the ignition in the OFF position: • Never pour fuel or other flammable liquid into the 2.
Page 343: After Starting
STARTING AND OPERATING 341 2. Press the accelerator pedal all the way to the floor and WARNING! (Continued) hold it. • If the vehicle has a discharged battery, booster 3. Push and release the ENGINE START/STOP button cables may be used to obtain a start from a booster once.
Page 344: Engine Block Heater - If Equipped
342 STARTING AND OPERATING ENGINE BLOCK HEATER — IF EQUIPPED AUTOMATIC TRANSMISSION The engine block heater warms the engine, and permits WARNING! quicker starts in cold weather. Connect the cord to a standard 110-115 Volt AC electrical outlet with a •...
Page 345 STARTING AND OPERATING 343 WARNING! (Continued) WARNING! (Continued) • Unintended movement of a vehicle could injure • Never leave children alone in a vehicle, or with those in or near the vehicle. As with all vehicles, access to an unlocked vehicle. Allowing children to you should never exit a vehicle while the engine is be in a vehicle unattended is dangerous for a running.
Page 346: Key Ignition Park Interlock
344 STARTING AND OPERATING before the engine can be turned off. This helps the driver CAUTION! avoid inadvertently leaving the vehicle without placing the transmission in PARK. Damage to the transmission may occur if the follow- ing precautions are not observed: This system also locks the transmission in PARK when- •...
Page 347: Eight-Speed Automatic Transmission
STARTING AND OPERATING 345 The electronically-controlled transmission provides a Eight-Speed Automatic Transmission precise shift schedule. The transmission electronics are The transmission is controlled using a rotary electronic self-calibrating; therefore, the first few shifts on a new gear selector located on the center console. The transmis- vehicle may be somewhat abrupt.
Page 348 346 STARTING AND OPERATING Standard Shifter Premium Shifter With AutoStick The standard transmission gear selector has PARK, RE- The premium transmission gear selector provides PARK, VERSE, NEUTRAL, DRIVE, and LOW shift positions. REVERSE, NEUTRAL, DRIVE, and SPORT shift posi- Using the LOW position manually downshifts the trans- tions.
Page 349 STARTING AND OPERATING 347 PARK (P) WARNING! This range supplements the parking brake by locking the • Never use the PARK position as a substitute for the transmission. The engine can be started in this range. parking brake. Always apply the parking brake Never attempt to use PARK while the vehicle is in fully when parked to guard against vehicle move- motion.
Page 350 348 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Unintended movement of a vehicle could injure • Never leave children alone in a vehicle, or with those in or near the vehicle. As with all vehicles, access to an unlocked vehicle. Allowing children to you should never exit a vehicle while the engine is be in a vehicle unattended is dangerous for a running.
Page 351 STARTING AND OPERATING 349 NOTE: REVERSE (R) • Before moving the transmission gear selector out of This range is for moving the vehicle backward. Shift into PARK, you must start the engine and also press the REVERSE only after the vehicle has come to a complete brake pedal.
Page 352 350 STARTING AND OPERATING When frequent transmission shifting occurs (such as CAUTION! when operating the vehicle under heavy loading condi- tions, in hilly terrain, traveling into strong head winds, or Towing the vehicle, coasting, or driving for any other while towing heavy trailers), use the AutoStick shift reason with the transmission in NEUTRAL can cause control (if equipped;...
Page 353 STARTING AND OPERATING 351 access SPORT mode, push down on the gear selector and greatest amount of steering feel. This mode may be rotate it fully clockwise, or press the SPORT button in the activated and deactivated by pushing the Sport button on center stack.
Page 354: Autostick - If Equipped
352 STARTING AND OPERATING In the event of a momentary problem, the transmission 6. Shift into the desired gear range. If the problem is no can be reset to regain all forward gears by performing the longer detected, the transmission will return to normal following steps: operation.
Page 355 STARTING AND OPERATING 353 can also provide you with more control during passing, lower gear, while using (+) to enter AutoStick will retain city driving, cold slippery conditions, mountain driving, the current gear. When AutoStick is active, the current trailer towing, and many other situations. transmission gear is displayed in the instrument cluster.
Page 356 354 STARTING AND OPERATING • If AutoStick is engaged while the transmission gear • If a requested downshift would cause the engine to selector is in the SPORT position, manual gear selec- over-speed, that shift will not occur. tion will be maintained until the gear selector is •...
Page 357: All-Wheel Drive (Awd) - If Equipped
STARTING AND OPERATING 355 conditions require increased levels of road traction, the WARNING! vehicle automatically shifts into AWD mode. Automatic AWD operation could be activated by outside tempera- Do not downshift for additional engine braking on a ture, wheel slip, or other predetermined conditions (there slippery surface.
Page 358: Driving On Slippery Surfaces
356 STARTING AND OPERATING CAUTION! WARNING! All wheels must have the same size and type tires. Rapid acceleration on slippery surfaces is dangerous. Unequal tire sizes must not be used. Unequal tire Unequal traction can cause sudden pulling of the rear size may cause failure of the front differential and/or wheels.
Page 359: Driving Through Water
STARTING AND OPERATING 357 • Slow down if the road has standing water or puddles. Flowing/Rising Water • Replace tires when tread wear indicators first become WARNING! visible. Do not drive on or across a road or path where water •...
Page 360 358 STARTING AND OPERATING WARNING! CAUTION! • Driving through standing water limits your vehi- • Always check the depth of the standing water cle’s traction capabilities. Do not exceed 5 mph before driving through it. Never drive through (8 km/h) when driving through standing water. standing water that is deeper than the bottom of •...
Page 361: Electric Power Steering
STARTING AND OPERATING 359 ELECTRIC POWER STEERING CAUTION! (Continued) The electric power steering system will give you good • Driving through standing water may cause damage vehicle response and increased ease of maneuverability to your vehicle’s drivetrain components. Always in tight spaces. The system will vary its assist to provide inspect your vehicle’s fluids (i.e., engine oil, trans- light efforts while parking and good feel while driving.
Page 362: Fuel Saver Technology 5.7L Engine Only
360 STARTING AND OPERATING NOTE: WARNING! • Even if the power steering assistance is no longer Continued operation with reduced assist could pose operational, it is still possible to steer the vehicle. a safety risk to yourself and others. Service should be Under these conditions there will be a substantial obtained as soon as possible.
Page 363: Parking Brake
STARTING AND OPERATING 361 PARKING BRAKE Before leaving the vehicle, make sure that the parking brake is fully applied and place the shift lever/gear selector in the PARK position. The foot operated parking brake is located below the lower left corner of the instrument panel. To apply the park brake, firmly push the park brake pedal fully.
Page 364 362 STARTING AND OPERATING NOTE: WARNING! • When the parking brake is applied and the transmis- • Never use the PARK position as a substitute for the sion is placed in gear, the “Brake Warning Light” will parking brake. Always apply the parking brake flash.
Page 365: Brake System
STARTING AND OPERATING 363 WARNING! (Continued) CAUTION! • Do not leave the Key Fob in or near the vehicle (or If the “Brake Warning Light” remains on with the in a location accessible to children), and do not parking brake released, a brake system malfunction leave the ignition of a vehicle equipped with is indicated.
Page 366: Electronic Brake Control System
364 STARTING AND OPERATING In the event power assist is lost for any reason (for All four of these systems work together to enhance example, repeated brake applications with the engine vehicle stability and control in various driving condi- OFF) the brakes will still function. The effort required to tions.
Page 367 STARTING AND OPERATING 365 related motor noises. These noises are the system per- These are all normal characteristics of ABS. forming its self check cycle to ensure that the ABS is working properly. This self check occurs each time the WARNING! vehicle is started and accelerated past 7 mph (11 km/h).
Page 368: Traction Control System (Tcs)
366 STARTING AND OPERATING Traction Control System (TCS) WARNING! (Continued) This system monitors the amount of wheel spin of each • The ABS cannot prevent the natural laws of phys- driven wheel. If wheel spin is detected, brake pressure is ics from acting on the vehicle, nor can it increase applied to the slipping wheel(s) and engine power is braking or steering efficiency beyond that afforded...
Page 369: Brake Assist System (Bas)
STARTING AND OPERATING 367 Brake Assist System (BAS) WARNING! This system complements the ABS by optimizing the The BAS cannot prevent the natural laws of physics vehicle braking capability during emergency brake ma- from acting on the vehicle, nor can it increase the neuvers.
Page 370 368 STARTING AND OPERATING power may also be reduced to assist in counteracting the WARNING! condition of oversteer or understeer and help the vehicle maintain the desired path. The Electronic Stability Control (ESC) cannot pre- vent the natural laws of physics from acting on the The ESC uses sensors in the vehicle to determine the path vehicle, nor can it increase the traction afforded by that the driver intends to steer the vehicle and compares...
Page 371 STARTING AND OPERATING 369 ESC Operating Modes The “ESC Off” switch is located on the switch bank in the center of the instrument panel. To enter the “Partial Off” The ESC system has two or three available operating mode, momentarily push the “ESC Off” switch and the modes: ESC off indicator light will illuminate.
Page 372 370 STARTING AND OPERATING NOTE: Full Off — If Equipped • To improve the vehicle’s traction when driving with This mode is intended for off-highway or off-road use snow chains, or when starting off in deep snow, sand, only and should not be used on any public roadways. In or gravel, it may be desirable to switch to the “Partial this mode, all TCS and ESC stability features are turned Off”...
Page 373: Hill Start Assist (Hsa)
STARTING AND OPERATING 371 system will release brake pressure in proportion to the WARNING! amount of throttle applied as the vehicle starts to move in the intended direction of travel. In the ESC “Full Off” mode, the engine torque reduction and stability features are disabled. There- HSA Activation Criteria fore, the enhanced vehicle stability offered by ESC is The following criteria must be met in order for HSA to...
Page 374 372 STARTING AND OPERATING WARNING! WARNING! (Continued) brake pedal is released, there may not be enough There may be situations on minor hills with a loaded brake pressure to hold the vehicle and trailer on a vehicle, or while pulling a trailer, when the system hill and this could cause a collision with another will not activate and slight rolling may occur.
Page 375: Ready Alert Braking
STARTING AND OPERATING 373 HSA Off Rain Brake Support If you wish to turn off the HSA system, it can be done in Rain Brake Support may improve braking performance the Uconnect® Settings. Refer to Uconnect® Settings in in wet conditions. It will periodically apply a small Understanding Your Instrument Panel for further infor- amount of brake pressure to remove any water buildup mation.
Page 376 374 STARTING AND OPERATING malfunction has been detected in the ESC system. If this NOTE: light remains on after several ignition cycles, and the • Each time the ignition is cycled ON, the ESC system vehicle has been driven several miles (kilometers) at will be ON even if it was cycled off previously.
Page 377: Synchronizing Esc
STARTING AND OPERATING 375 Synchronizing ESC TIRE SAFETY INFORMATION Tire Markings If the power supply is interrupted (battery disconnected discharged), “ESC Activation/Malfunction Indicator Light” may illuminate with the engine running. If this should occur, turn the steering wheel completely to the left and then to the right.
Page 378 376 STARTING AND OPERATING NOTE: • Temporary spare tires are designed for temporary emergency use only. Temporary high pressure com- • P (Passenger) — Metric tire sizing is based on U.S. pact spare tires have the letter “T” or “S” molded into design standards.
Page 379 STARTING AND OPERATING 377 Tire Sizing Chart EXAMPLE: Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 P = Passenger car tire size based on U.S. design standards, or ..blank..= Passenger car tire based on European design standards, or LT = Light truck tire based on U.S.
Page 380 378 STARTING AND OPERATING EXAMPLE: R = Construction code – R means radial construction, or – D means diagonal or bias construction 15, 16, 18 = Rim diameter in inches (in) Service Description: 95 = Load Index – A numerical code associated with the maximum load a tire can carry H = Speed Symbol –...
Page 381: Tire Identification Number (Tin)
STARTING AND OPERATING 379 EXAMPLE: Load Identification: Absence of the following load identification symbols on the sidewall of the tire indicates a Standard Load (SL) tire: • XL = Extra load (or reinforced) tire, or • LL = Light load tire or •...
Page 382 380 STARTING AND OPERATING EXAMPLE: DOT MA L9 ABCD 0301 DOT = Department of Transportation – This symbol certifies that the tire is in compliance with the U.S. Department of Transportation tire safety standards and is approved for highway use MA = Code representing the tire manufacturing location (two digits) L9 = Code representing the tire size (two digits) ABCD = Code used by the tire manufacturer (one to four digits)
Page 383: Tire Terminology And Definitions
STARTING AND OPERATING 381 Tire Terminology And Definitions Term Definition B-Pillar The vehicle B-Pillar is the structural member of the body located behind the front door. Cold Tire Inflation Pressure Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting for a minimum of three hours.
Page 384: Tire Loading And Tire Pressure
382 STARTING AND OPERATING Tire Loading And Tire Pressure Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door. Example Tire Placard Location (B-Pillar) Example Tire Placard Location (Door) I n f o r ma t i o n P r o v i d e d b y :...
Page 385 STARTING AND OPERATING 383 Tire And Loading Information Placard This placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4.
Page 386 384 STARTING AND OPERATING NOTE: Under a maximum loaded vehicle condition, Steps For Determining Correct Load Limit gross axle weight ratings (GAWRs) for the front and rear 1. Locate the statement “The combined weight of occu- axles must not be exceeded. For further information on pants and cargo should never exceed XXX lbs or GAWRs, vehicle loading, and trailer towing, refer to XXX kg”...
Page 387 STARTING AND OPERATING 385 4. The resulting figure equals the available amount of NOTE: cargo and luggage load capacity. For example, if • If your vehicle will be towing a trailer, load from your “XXX” amount equals 1,400 lbs (635 kg) and there will trailer will be transferred to your vehicle.
Page 388 386 STARTING AND OPERATING I n f o r ma t i o n P r o v i d e d b y :...
Page 389: Tires - General Information
STARTING AND OPERATING 387 Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause collisions. recommended load capacity for your vehicle.
Page 390 388 STARTING AND OPERATING Fuel Economy WARNING! (Continued) Underinflated tires will increase tire rolling resistance • Unequal tire pressures from one side of the vehicle resulting in higher fuel consumption. to the other can cause the vehicle to drift to the right or left.
Page 391: Tire Inflation Pressures
STARTING AND OPERATING 389 Inflation pressures specified on the placard are always Tire Inflation Pressures “cold tire inflation pressure”. Cold tire inflation pressure The proper cold tire inflation pressure is listed on the is defined as the tire pressure after the vehicle has not driver’s side B-Pillar or rear edge of the driver’s side been driven for at least three hours, or driven less than 1 door.
Page 392: Tire Pressures For High Speed Operation
390 STARTING AND OPERATING inflation pressure should be increased by 3 psi (21 kPa), WARNING! which equals 1 psi (7 kPa) for every 12°F (7°C) for this outside temperature condition. High speed driving with your vehicle under maxi- mum load is dangerous. The added strain on your Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) tires could cause them to fail.
Page 393: Tire Types
STARTING AND OPERATING 391 Tire Repair Tire Types If your tire becomes damaged, it may be repaired if it All Season Tires — If Equipped meets the following criteria: All Season tires provide traction for all seasons (Spring, • The tire has not been driven on when flat. Summer, Fall and Winter).
Page 394 392 STARTING AND OPERATING Summer tires do not contain the all season designation or If you need snow tires, select tires mountain/snowflake symbol on the tire sidewall. Use equivalent in size and type to the origi- Summer tires only in sets of four; failure to do so may nal equipment tires.
Page 395: Run Flat Tires - If Equipped
STARTING AND OPERATING 393 Run Flat Tires — If Equipped Spare Tires — If Equipped Run Flat tires allow you the capability to drive 50 miles NOTE: For vehicles equipped with Tire Service Kit (80 km) at 50 mph (80 km/h) after a rapid loss of inflation instead of a spare tire, please refer to “Tire Service Kit”...
Page 396 394 STARTING AND OPERATING rotation for your vehicle. If your vehicle has this option, Do not install a wheel cover or attempt to mount a refer to an authorized tire dealer for the recommended conventional tire on the compact spare wheel, since the tire rotation pattern.
Page 397 STARTING AND OPERATING 395 Full Size Spare — If Equipped your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the The full size spare is for temporary emergency use only. first opportunity. This tire may look like the originally equipped tire on the front or rear axle of your vehicle, but it is not.
Page 398: Tire Spinning
396 STARTING AND OPERATING Tire Spinning Tread Wear Indicators When stuck in mud, sand, snow, or ice conditions, do not Tread wear indicators are in the original equipment tires spin your vehicle’s wheels above 30 mph (48 km/h) or to help you in determining when your tires should be for longer than 30 seconds continuously without stop- replaced.
Page 399: Life Of Tire
STARTING AND OPERATING 397 These indicators are molded into the bottom of the tread • Performance tires, tires with a speed rating of V or grooves. They will appear as bands when the tread depth higher, and Summer tires typically have a reduced becomes a 1/16 of an inch (2 mm).
Page 400: Replacement Tires
398 STARTING AND OPERATING It is recommended to replace the two front tires or two Replacement Tires rear tires as a pair. Replacing just one tire can seriously The tires on your new vehicle provide a balance of many affect your vehicle’s handling. If you ever replace a characteristics.
Page 401: Tire Chains (Traction Devices)
STARTING AND OPERATING 399 WARNING! WARNING! (Continued) • Failure to equip your vehicle with tires having • Do not use a tire, wheel size or rating other than adequate speed capability can result in sudden tire that specified for your vehicle. Some combinations failure and loss of vehicle control.
Page 402 400 STARTING AND OPERATING • Install on Rear Tires Only. CAUTION! • Due to limited clearance for a Rear Wheel Drive To avoid damage to your vehicle or tires, observe the (RWD) vehicle, on P215/65R17, P225/60R18 and following precautions: P235/55R18 tires with a Security Chain Company •...
Page 403: Tire Rotation Recommendations
STARTING AND OPERATING 401 These effects can be reduced by timely rotation of tires. CAUTION! (Continued) The benefits of rotation are especially worthwhile with • Observe the traction device manufacturer’s instruc- aggressive tread designs such as those on all season type tions on the method of installation, operating tires.
Page 404: Tire Pressure Monitor System (Tpms)
402 STARTING AND OPERATING The suggested rotation method is the “forward cross” TIRE PRESSURE MONITOR SYSTEM (TPMS) shown in the following diagram. This rotation pattern The Tire Pressure Monitor System (TPMS) will warn the does not apply to some directional tires that must not be driver of a low tire pressure based on the vehicle recom- reversed.
Page 405 STARTING AND OPERATING 403 also increase as the vehicle is driven - this is normal and may need to be driven for up to 20 minutes above 15 mph there should be no adjustment for this increased pres- (24 km/h) in order for the TPMS to receive this informa- sure.
Page 406 404 STARTING AND OPERATING NOTE: CAUTION! • The TPMS is not intended to replace normal tire care • The TPMS has been optimized for the original and maintenance or to provide warning of a tire failure equipment tires and wheels. TPMS pressures and or condition.
Page 407: Base System
STARTING AND OPERATING 405 • Seasonal temperature changes will affect tire pressure, The matching full size spare wheel and tire assembly (if and the TPMS will monitor the actual tire pressure in equipped) has a TPM sensor. The matching full size spare the tire.
Page 408 406 STARTING AND OPERATING pressure value as shown in the Inflate to XX message. 2. Installing aftermarket window tinting that contains Once the system receives the updated tire pressures, the materials that may block radio wave signals. system will automatically update and the TPM Telltale 3.
Page 409 STARTING AND OPERATING 407 3. Driving the vehicle for up to 20 minutes above 15 mph 3. After driving the vehicle for up to 20 minutes above (24 km/h) will turn off the TPM Telltale Light and 15 mph (24 km/h), the LOW TIRE message will turn LOW TIRE message as long as no tire pressure is off and the TPM Telltale Light will flash on and off for below the low-pressure warning limit in any of the...
Page 410: Premium System - If Equipped
408 STARTING AND OPERATING The matching full size spare wheel and tire assembly (if Premium System — If Equipped equipped) has a TPM sensor. The full size spare can be The Tire Pressure Monitor System (TPMS) uses wireless used in place of any of the four road tires. The TPMS will technology with wheel rim mounted electronic sensors to only monitor the pressure in the full size spare tire when monitor tire pressure levels.
Page 411 STARTING AND OPERATING 409 will automatically update, the graphic display in the DID will stop flashing or change color back to the original color, and the TPM Telltale Light will turn off. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the TPMS to receive this informa- tion.
Page 412 410 STARTING AND OPERATING Service TPMS Warning 2. Installing aftermarket window tinting that contains materials that may block radio wave signals. If a system fault is detected, the TPM Telltale Light will flash on and off for 75 seconds and then remain on solid. 3.
Page 413 STARTING AND OPERATING 411 Vehicles With Full Size Spare Vehicles With Compact Spare 1. The matching full size spare wheel and tire assembly 1. The compact spare tire does not have a TPM sensor. has a TPM sensor that can be monitored by the TPMS. Therefore, the TPMS will not monitor the pressure in the compact spare tire.
Page 414: General Information
412 STARTING AND OPERATING 4. For each subsequent ignition switch cycle, a chime will General Information sound, the TPM Telltale Light will flash on and off for This device complies with Part 15 of the FCC rules and 75 seconds and then remain on solid, and the DID will RSS 210 of Industry Canada.
Page 415: Fuel Requirements
STARTING AND OPERATING 413 Poor quality gasoline can cause problems such as hard FUEL REQUIREMENTS starting, stalling, and hesitations. If you experience these 3.6L Engine — If Equipped symptoms, try another brand of gasoline before consid- ering service for the vehicle. This engine is designed to meet all emis- 5.7L Engine —...
Page 416: Reformulated Gasoline
414 STARTING AND OPERATING making a heavy knocking sound, see your dealer imme- Gasoline/Oxygenate Blends diately. Use of gasoline with an octane number lower Some fuel suppliers blend unleaded gasoline with oxy- than 87 can cause engine failure and may void or not be genates such as ethanol.
Page 417: E-85 Usage In Non-Flex Fuel Vehicles
STARTING AND OPERATING 415 blended into some gasoline to increase octane. Gasoline E-85 Usage In Non-Flex Fuel Vehicles blended with MMT provides no performance advantage Non-Flex Fuel Vehicles (FFV) are compatible with gaso- beyond gasoline of the same octane number without line containing up to 10% ethanol (E10).
Page 418: Fuel System Cautions
416 STARTING AND OPERATING Fuel System Cautions CAUTION! (Continued) • The use of fuel additives, which are now being CAUTION! sold as octane enhancers, is not recommended. Follow these guidelines to maintain your vehicle’s Most of these products contain high concentrations performance: of methanol.
Page 419: Carbon Monoxide Warnings
STARTING AND OPERATING 417 Carbon Monoxide Warnings WARNING! (Continued) • Guard against carbon monoxide with proper main- WARNING! tenance. Have the exhaust system inspected every Carbon monoxide (CO) in exhaust gases is deadly. time the vehicle is raised. Have any abnormal Follow the precautions below to prevent carbon conditions repaired promptly.
Page 420: Ethanol Fuel (E-85)
418 STARTING AND OPERATING Fuel Requirements CAUTION! If your vehicle is E-85 compatible, it will operate on Only vehicles with the E-85 fuel filler door label can unleaded gasoline with any octane rating, or solely E-85 operate on E-85. fuel, or any mixture of these fuels. For best results, avoid fueling patterns alternating Ethanol Fuel (E-85) between E-85 and unleaded gasoline.
Page 421: Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles
STARTING AND OPERATING 419 NOTE: Chrysler Specification MS-6395. It is recommended that engine oils that are API Certified and meet the require- • Use seasonally adjusted E-85 fuel (ASTM D5798). With ments of Material Standard MS-6395 be used. MS-6395 non-seasonally adjusted E-85 fuel, hard starting and...
Page 422: Cruising Range
420 STARTING AND OPERATING Cruising Range CAUTION! Because E-85 fuel contains less energy per gallon/liter Replacing fuel system components with non-ethanol than gasoline, an increase in fuel consumption will be compatible components can damage your vehicle. experienced. The miles per gallon (mpg)/kilometers per liter and the driving range will decrease by approxi- Maintenance mately 30%, compared to gasoline operation.
Page 423: Adding Fuel
STARTING AND OPERATING 421 ADDING FUEL 1. Press the fuel filler door release switch (located in the driver’s door map pocket). Fuel Filler Door NOTE: In certain cold conditions, ice may prevent the fuel door from opening. If this occurs, lightly push on the fuel door to break the ice buildup and re-release the fuel Fuel Filler Door Release Switch door using the inside release button.
Page 424 422 STARTING AND OPERATING 3. There is no fuel filler cap. A flapper door inside the pipe seals the system. 4. Insert the fuel nozzle fully into the filler pipe – the nozzle opens and holds the flapper door while refuel- ing.
Page 425: Emergency Fuel Filler Door Release
STARTING AND OPERATING 423 2. Remove the access cover (located on the left side inner WARNING! trim panel). • Never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being filled.
Page 426: Vehicle Loading
424 STARTING AND OPERATING 3. Pull the release cable. Do not exceed the specified Gross Vehicle Weight Rating (GVWR) or the Gross Axle Weight Rating (GAWR). Vehicle Certification Label Your vehicle has a Vehicle Certification Label affixed to the drivers side B-Pillar or the rear of the driver’s door. The label contains the following information: •...
Page 427: Gross Vehicle Weight Rating (Gvwr)
STARTING AND OPERATING 425 Gross Vehicle Weight Rating (GVWR) Overloading The GVWR is the total allowable weight of your vehicle. The load carrying components (axle, springs, tires, This includes driver, passengers, and cargo. The total wheels, etc.) of your vehicle will provide satisfactory load must be limited so that you do not exceed the service as long as you do not exceed the GVWR and the GVWR.
Page 428: Loading
426 STARTING AND OPERATING Loading TRAILER TOWING To load your vehicle properly, first figure out its empty In this section you will find safety tips and information weight, axle-by-axle and side-by-side. Store heavier items on limits to the type of towing you can reasonably do down low and be sure you distribute their weight as with your vehicle.
Page 429 STARTING AND OPERATING 427 exceed the GVWR. Refer to “Vehicle Loading/Vehicle Gross Axle Weight Rating (GAWR) Certification Label” in “Starting And Operating” for The GAWR is the maximum capacity of the front and rear further information. axles. Distribute the load over the front and rear axles evenly.
Page 430 428 STARTING AND OPERATING Tongue Weight (TW) Trailer Sway Control The tongue weight is the downward force exerted on the The trailer sway control is a telescoping link that can be hitch ball by the trailer. The recommended tongue weight installed between the hitch receiver and the trailer tongue is 10% to 15% of the vehicle’s GTW for a conventional that typically provides adjustable friction associated with...
Page 431 STARTING AND OPERATING 429 Weight-Distributing Hitch WARNING! A weight-distributing system works by applying lever- • An improperly adjusted Weight Distributing Hitch age through spring (load) bars. They are typically used system may reduce handling, stability, braking for heavier loads to distribute trailer tongue weight to the performance, and could result in a collision.
Page 432: Trailer Hitch Classification
430 STARTING AND OPERATING Trailer Hitch Classification The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Trailer Hitch Classification Definitions Class Max.
Page 433: Trailer Towing Weights (Maximum Trailer Weight Ratings)
STARTING AND OPERATING 431 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Max. GTW (Gross Max. Tongue Weight (See Engine/Transmission Frontal Area Trailer Weight) Note) 3.6L Automatic 22 sq ft (2.04 sq m) 1,000 lbs (454 kg) 100 lbs (45 kg)
Page 434: Trailer And Tongue Weight
432 STARTING AND OPERATING Trailer And Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle.
Page 435: Towing Requirements
STARTING AND OPERATING 433 NOTE: Remember that everything put into or on the WARNING! trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must Improper towing can lead to an injury collision. be considered as part of the total load on your vehicle. Follow these guidelines to make your trailer towing Refer to the “Tire And Loading Information”...
Page 436 434 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Safety chains must always be used between your • Total weight must be distributed between the tow vehicle and trailer. Always connect the chains to vehicle and the trailer such that the following four the frame or hook retainers of the vehicle hitch.
Page 437 STARTING AND OPERATING 435 “Tires – General Information” in “Starting And Oper- CAUTION! ating” for information on tire pressures and for proper tire inflation procedures. • Do not tow a trailer at all during the first 500 miles (805 km) the new vehicle is driven. The engine, axle •...
Page 438 436 STARTING AND OPERATING Towing Requirements — Trailer Brakes WARNING! • Do not interconnect the hydraulic brake system or • Do not connect trailer brakes to your vehicle’s vacuum system of your vehicle with that of the trailer. hydraulic brake lines. It can overload your brake This could cause inadequate braking and possible system and cause it to fail.
Page 439 STARTING AND OPERATING 437 The Trailer Tow Package may include a four- and seven- CAUTION! pin wiring harness. Use a factory approved trailer har- ness and connector. If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they NOTE: Do not cut or splice wiring into the vehicles should be of adequate capacity.
Page 440 438 STARTING AND OPERATING Four-Pin Connector Seven-Pin Connector 1 — Female Pins 4 — Park 1 — Battery 5 — Ground 2 — Male Pin 5 — Left Stop/Turn 2 — Backup Lamps 6 — Left Stop/Turn 3 — Ground 6 —...
Page 441: Towing Tips
STARTING AND OPERATING 439 Electronic Speed Control — If Equipped Towing Tips Before setting out on a trip, practice turning, stopping, • Do not use in hilly terrain or with heavy loads. and backing up the trailer in an area located away from •...
Page 442: Recreational Towing
440 STARTING AND OPERATING • To prevent excess heat generation, avoid continuous RECREATIONAL TOWING (BEHIND driving at high RPM. Reduce vehicle speed as neces- MOTORHOME, ETC.) sary to avoid extended driving at high RPM. Return to Two-Wheel Drive And All-Wheel Drive a higher gear or vehicle speed when grade and road Recreational towing (with all four wheels on the ground, conditions allow.
Page 443 WHAT TO DO IN EMERGENCIES CONTENTS HAZARD WARNING FLASHERS ...442 JUMP-STARTING PROCEDURES ...455 IF YOUR ENGINE OVERHEATS ... .442 ▫...
Page 444: Hazard Warning Flashers
442 WHAT TO DO IN EMERGENCIES NOTE: With extended use the Hazard Warning flashers HAZARD WARNING FLASHERS may wear down your battery. The Hazard Warning flasher switch is located in the center of the instrument panel between the center air IF YOUR ENGINE OVERHEATS outlets.
Page 445: Wheel And Tire Torque Specifications
WHAT TO DO IN EMERGENCIES 443 • You can also turn the temperature control to maximum WARNING! heat, the mode control to floor and the blower control to high. This allows the heater core to act as a You or others can be badly burned by hot engine supplement to the radiator and aids in removing heat coolant (antifreeze) or steam from your radiator.
Page 446: Torque Specifications
444 WHAT TO DO IN EMERGENCIES Torque Specifications Lug Nut/Bolt Torque **Lug Nut/ Lug Nut/ Bolt Size Bolt Socket Size 130 Ft-Lbs (176 N·m) M14 x 1.50 22 mm **Use only your Authorized Dealer recommended lug nuts/bolts and clean or remove any dirt or oil before tightening.
Page 447: Jacking And Tire Changing
WHAT TO DO IN EMERGENCIES 445 JACKING AND TIRE CHANGING WARNING! • Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.
Page 448: Jack Location/Spare Tire Stowage
446 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • The jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas.
Page 449 WHAT TO DO IN EMERGENCIES 447 Spare Tire Fastener Jack Fastener 4. Remove the spare tire. 6. Remove the jack and lug wrench assembly from under the spare tire. Turn the jack screw to the left to loosen 5. Remove the fastener securing the jack. the lug wrench, and remove the wrench from the jack assembly.
Page 450: Preparations For Jacking
448 WHAT TO DO IN EMERGENCIES 2. Turn on the Hazard Warning flasher. WARNING! 3. Set the parking brake. A loose tire or jack thrown forward in a collision or 4. Place the shift lever/gear selector into PARK. hard stop could endanger the occupants of the ve- hicle.
Page 451: Jacking And Changing A Tire
WHAT TO DO IN EMERGENCIES 449 Jacking And Changing A Tire WARNING! (Continued) • Do not let anyone sit in the vehicle when it is on a WARNING! jack. Carefully follow these tire changing warnings to • Do not get under the vehicle when it is on a jack. If help prevent personal injury or damage to your you need to get under a raised vehicle, take it to a vehicle:...
Page 452 450 WHAT TO DO IN EMERGENCIES CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking Instructions for this vehicle. 1. Remove the spare tire, jack, and lug wrench. 2. If equipped with aluminum wheels where the center cap covers the lug nuts, use the lug wrench to pry the center cap off carefully before raising the vehicle.
Page 453 WHAT TO DO IN EMERGENCIES 451 Front Jacking Location Rear Jacking Location 5. Raise the vehicle just enough to remove the flat tire and install the spare tire. I n f o r ma t i o n P r o v i d e d b y :...
Page 454 452 WHAT TO DO IN EMERGENCIES WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts and tire. 7.
Page 455 WHAT TO DO IN EMERGENCIES 453 NOTE: 9. Lower the vehicle to the ground by turning the jack handle counterclockwise. • For vehicles so equipped, do not attempt to install a center cap or wheel cover on the compact spare. 10.
Page 456: Road Tire Installation
454 WHAT TO DO IN EMERGENCIES WARNING! WARNING! A loose tire or jack thrown forward in a collision or To avoid the risk of forcing the vehicle off the jack, hard stop could endanger the occupants of the ve- do not tighten the lug nuts fully until the vehicle has hicle.
Page 457: Jump-Starting Procedures
WHAT TO DO IN EMERGENCIES 455 JUMP-STARTING PROCEDURES WARNING! If your vehicle has a discharged battery it can be jump- Do not attempt jump-starting if the battery is frozen. started using a set of jumper cables and a battery in It could rupture or explode and cause personal injury.
Page 458 456 WHAT TO DO IN EMERGENCIES WARNING! • Take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is ON. You can be injured by moving fan blades. • Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.
Page 459: Jump-Starting Procedure
WHAT TO DO IN EMERGENCIES 457 3. If using another vehicle to jump-start the battery, park CAUTION! the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is OFF. Failure to follow these procedures could result in damage to the charging system of the booster vehicle WARNING! or the discharged vehicle.
Page 460 458 WHAT TO DO IN EMERGENCIES Disconnecting The Jumper Cables WARNING! 1. Disconnect the negative (-) jumper cable from the Do not connect the jumper cable to the negative (-) remote negative (-) post of the vehicle with the dis- post of the discharged battery.
Page 461: Freeing A Stuck Vehicle
WHAT TO DO IN EMERGENCIES 459 NOTE: Shifts between DRIVE and REVERSE can only be CAUTION! achieved at wheel speeds of 5 mph (8 km/h) or less. Whenever the transmission remains in NEUTRAL for Accessories plugged into the vehicle power outlets more than 2 seconds, you must push the brake pedal to draw power from the vehicle’s battery, even when not engage DRIVE or REVERSE.
Page 462: Manual Park Release
460 WHAT TO DO IN EMERGENCIES NOTE: Push the ESC Off switch, to place the Electronic WARNING! Stability Control (ESC) system in Partial Off mode, before rocking the vehicle. Refer to “Electronic Brake Fast spinning tires can be dangerous. Forces gener- Control”...
Page 463 WHAT TO DO IN EMERGENCIES 461 2. Remove the console storage bin to access the Manual WARNING! (Continued) Park Release lever. allow your vehicle to roll away if it is not secured by the parking brake or by proper connection to a tow vehicle.
Page 464 462 WHAT TO DO IN EMERGENCIES 3. Using a small screwdriver or similar tool, fish the 5. While holding the locking tab in the disengaged tether strap up through the opening in the console position, pull the tether strap to rotate the lever up and base.
Page 465: Towing A Disabled Vehicle
WHAT TO DO IN EMERGENCIES 463 To Reset The Manual Park Release: 4. Tuck the tether strap into the base of the console. Reinstall the console storage bin. 1. Push the latch (at the base of the lever, on the rear side) rearward (away from the lever) to unlatch the lever.
Page 466 464 WHAT TO DO IN EMERGENCIES Towing Wheels OFF The Ground RWD MODELS AWD MODELS Condition Flat Tow NONE If transmission is operable: NOT ALLOWED • Transmission in NEUTRAL • 30 mph (48 km/h) max speed • 30 miles (48 km) max distance Wheel Lift or Front...
Page 467 WHAT TO DO IN EMERGENCIES 465 Proper towing or lifting equipment is required to prevent CAUTION! damage to your vehicle. Use only tow bars and other equipment designed for this purpose, following equip- • DO NOT use sling-type equipment when towing. ment manufacturer’s instructions.
Page 468: All Wheel Drive (Awd) Models
466 WHAT TO DO IN EMERGENCIES All Wheel Drive (AWD) Models CAUTION! The manufacturer recommends towing your vehicle with • Towing this vehicle using any other method can all four wheels OFF the ground using a flatbed. cause severe transmission and/or transfer case dam- If the transmission and drivetrain are operable, AWD age.
Page 469: Rear-Wheel Drive (Rwd) Models
WHAT TO DO IN EMERGENCIES 467 Rear-Wheel Drive (RWD) Models CAUTION! The manufacturer recommends towing your vehicle with Towing this vehicle in violation of the above require- all four wheels OFF the ground using a flatbed. ments can cause severe transmission damage. Dam- If flatbed equipment is not available, and the transmis- age from improper towing is not covered under the sion is operable, this vehicle may be flat towed (with all...
Page 470 I n f o r ma t i o n P r o v i d e d b y :...
Page 471 MAINTAINING YOUR VEHICLE CONTENTS ENGINE COMPARTMENT — 3.6L ..471 ▫ Engine Air Cleaner Filter ....481 ENGINE COMPARTMENT — 5.7L ..472 ▫...
Page 472 470 MAINTAINING YOUR VEHICLE ▫ Automatic Transmission ....499 ▫ Front Turn Signal Lamps ....525 ▫...
Page 473: Engine Compartment - 3.6L
MAINTAINING YOUR VEHICLE 471 ENGINE COMPARTMENT — 3.6L 1 — Remote Jump Start (Positive Battery 4 — Engine Oil Dipstick 7 — Air Cleaner Filter Post) 2 — Power Distribution Center (Fuses) 5 — Brake Fluid Reservoir Access Cover 8 — Engine Oil Fill 3 —...
Page 474: Engine Compartment - 5.7L
472 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 5.7L 1 — Remote Jump Start (Positive Battery 4 — Brake Fluid Reservoir Access Cover 7 — Engine Oil Fill Post) 2 — Power Distribution Center (Fuses) 5 — Engine Coolant Reservoir 8 — Engine Oil Dipstick 3 —...
Page 475: Onboard Diagnostic System - Obd Ii
MAINTAINING YOUR VEHICLE 473 ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard • Prolonged driving with the MIL on could cause diagnostic system called OBD II. This system monitors further damage to the emissions control system. It the performance of the emissions, engine, and automatic could also affect fuel economy and driveability.
Page 476 474 MAINTAINING YOUR VEHICLE NOTE: If you crank or start the engine, you will have to For states that require an Inspection and Mainte- start this test over. nance (I/M), this check verifies the “Malfunction Indicator Light (MIL)” is functioning and is not 2.
Page 477: Replacement Parts
MAINTAINING YOUR VEHICLE 475 If your OBD II system is not ready, you should see your caused by the use of non-MOPAR® parts for mainte- authorized dealer or repair facility. If your vehicle was nance and repairs will not be covered by the New Vehicle recently serviced or had a battery failure or replacement, Limited Warranty.
Page 478: Maintenance Procedures
476 MAINTAINING YOUR VEHICLE WARNING! CAUTION! You can be badly injured working on or around a • Failure to properly maintain your vehicle or per- motor vehicle. Only do service work for which you form repairs and service when necessary could have the knowledge and the proper equipment.
Page 479: Engine Oil
MAINTAINING YOUR VEHICLE 477 Checking Oil Level — 5.7L Engine Engine Oil To assure proper engine lubrication, the engine oil must Checking Oil Level — 3.6L Engine be maintained at the correct level. Check the oil level at To assure proper engine lubrication, the engine oil must regular intervals, such as every fuel stop.
Page 480 CAUTION! recommends engine oils that are API Certified and meet the requirements of Chrysler Material Standard MS-6395. Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by the New Vehicle Limited Warranty.
Page 481 MAINTAINING YOUR VEHICLE 479 Engine Oil Viscosity — 3.6L Engine Engine Oil Viscosity — 5.7L Engine MOPAR® SAE 5W-20 engine oil approved to Chrysler MOPAR® SAE 5W-20 engine oil or equivalent such as Material Standard MS-6395 such as Pennzoil®, Shell Pennzoil®...
Page 482: Engine Oil Filter
480 MAINTAINING YOUR VEHICLE Lubricants that do not have both, the engine oil certifi- indiscriminately discarded, can present a problem to the cation mark and the correct SAE viscosity grade number environment. Contact your authorized dealer, service should not be used. station or governmental agency for advice on how and where used oil and oil filters can be safely discarded in Synthetic Engine Oils...
Page 483: Engine Air Cleaner Filter
MAINTAINING YOUR VEHICLE 481 Engine Air Cleaner Filter Selection Engine Air Cleaner Filter Refer to the “Maintenance Schedule” for the proper The quality of replacement engine air cleaner filters maintenance intervals. varies considerably. Only high quality filters should be used to assure most efficient service. MOPAR® engine air WARNING! cleaner filters are a high quality filter and are recom- mended.
Page 484 482 MAINTAINING YOUR VEHICLE WARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area imme- diately with large amounts of water.
Page 485: Air Conditioner Maintenance
MAINTAINING YOUR VEHICLE 483 the condenser fins and a performance test. Drive belt tension CAUTION! should also be checked at this time. • It is essential when replacing the cables on the WARNING! battery that the positive cable is attached to the positive post and the negative cable is attached to •...
Page 486: A/C Air Filter
484 MAINTAINING YOUR VEHICLE Refrigerant Recovery And Recycling HFO 1234yf CAUTION! — If Equipped Do not use chemical flushes in your air conditioning HFO 1234yf Air Conditioning Refrigerant is a hydro- system as the chemicals can damage your air condi- fluorocarbon (HFC) that is endorsed by the Environmen- tioning components.
Page 487 MAINTAINING YOUR VEHICLE 485 1. Remove the access door in the cowl screen by pressing the retaining clips. Filter Access Cover 3. Remove the used filter. Access Door 4. Install the new filter with arrows pointing in the 2. Unsnap both ends and lift the filter access cover. direction of airflow, which is toward the rear of the vehicle (text and arrows on the filter will indicate this).
Page 488: Body Lubrication
486 MAINTAINING YOUR VEHICLE Body Lubrication Locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate, tailgate, decklid, sliding doors and hood hinges, should be lubricated periodically with a lithium based grease, such as MOPAR®...
Page 489: Windshield Wiper Blades
MAINTAINING YOUR VEHICLE 487 Windshield Wiper Blades Adding Washer Fluid Clean the rubber edges of the wiper blades and the The windshield washer fluid reservoir is located in the windshield periodically with a sponge or soft cloth and a front of the engine compartment. Be sure to check the mild nonabrasive cleaner.
Page 490: Exhaust System
488 MAINTAINING YOUR VEHICLE The fluid reservoir will hold nearly 1 gallon (4 liters) of have an authorized technician inspect the complete ex- washer fluid when the message “Low Washer Fluid” haust system and adjacent body areas for broken, dam- appears in the Driver Information Display (DID).
Page 491 MAINTAINING YOUR VEHICLE 489 WARNING! (Continued) CAUTION! (Continued) • A hot exhaust system can start a fire if you park • Damage to the catalytic converter can result if your over materials that can burn. Such materials might vehicle is not kept in proper operating condition. be grass or leaves coming into contact with your In the event of engine malfunction, particularly exhaust system.
Page 492: Cooling System
490 MAINTAINING YOUR VEHICLE NOTE: Intentional tampering with emissions control • Do not idle the engine with any spark plug wires systems can result in civil penalties being assessed disconnected or removed, such as when diagnostic against you. testing, or for prolonged periods during very rough idle or malfunctioning operating conditions.
Page 493 MAINTAINING YOUR VEHICLE 491 Coolant Checks If the cap is sealing properly, the engine coolant (anti- freeze) will begin to drain from the coolant recovery Check engine coolant (antifreeze) protection every 12 bottle. DO NOT REMOVE THE COOLANT PRESSURE months (before the onset of freezing weather, where CAP WHEN THE COOLING SYSTEM IS HOT.
Page 494 492 MAINTAINING YOUR VEHICLE Selection Of Coolant CAUTION! (Continued) Refer to “Fluids, Lubricants, And Genuine Parts” in OAT coolant (conforming to MS.90032), by an au- “Maintaining Your Vehicle” for further information. thorized dealer as soon as possible. • Do not use water alone or alcohol-based engine CAUTION! coolant (antifreeze) products.
Page 495 • Mix a minimum solution of 50% OAT engine coolant ing this extended maintenance period, it is important that that meets the requirements of Chrysler Material Stan- you use the same engine coolant (OAT coolant conform- dard MS.90032 and distilled water. Use higher concen- ing to MS.90032) throughout the life of your vehicle.
Page 496 494 MAINTAINING YOUR VEHICLE NOTE: The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces. • Some vehicles require special tools to add coolant properly. Failure to fill these systems properly could WARNING! lead to severe internal engine damage.
Page 497 If ingested by a child or pet, seek maintain the proper level, only OAT coolant that meets emergency assistance immediately. Clean up any ground the requirements of Chrysler Material Standard MS.90032 spills immediately. should be added to the coolant bottle. Do not overfill.
Page 498: Brake System
496 MAINTAINING YOUR VEHICLE If an examination of your engine compartment shows no • Make sure that the coolant expansion bottle overflow evidence of radiator or hose leaks, the vehicle may be hoses are not kinked or obstructed. safely driven. The vapor will soon dissipate. •...
Page 499 MAINTAINING YOUR VEHICLE 497 Clean the top of the master cylinder area before removing WARNING! the cap. Add fluid to bring the level up to the top of the “FULL” mark on the side of the master cylinder reservoir. Riding the brakes can lead to brake failure and possibly a collision.
Page 500 498 MAINTAINING YOUR VEHICLE WARNING! WARNING! (Continued) cause it to boil unexpectedly during hard or pro- • Use only manufacturer’s recommended brake longed braking, resulting in sudden brake failure. fluid. Refer to “Fluids, Lubricants, And Genuine This could result in a collision. Parts”...
Page 501: Automatic Transmission
MAINTAINING YOUR VEHICLE 499 Special Additives Automatic Transmission The manufacturer strongly recommends against using Selection Of Lubricant any special additives in the transmission. It is important to use the proper transmission fluid to ensure optimum transmission performance and life. Use Automatic Transmission Fluid (ATF) is an engineered only the manufacturer’s specified transmission fluid.
Page 502: All Wheel Drive (Awd) - If Equipped
500 MAINTAINING YOUR VEHICLE Fluid Level Check Fluid And Filter Changes The fluid level is preset at the factory and does not require Under normal operating conditions, the fluid installed at adjustment under normal operating conditions. Routine the factory will provide satisfactory lubrication for the fluid level checks are not required, therefore the transmis- life of the vehicle.
Page 503: Rear Axle
MAINTAINING YOUR VEHICLE 501 case fluid level, remove the fill/inspection plug. The fluid level. Refer to “Fluids, Lubricants, And Genuine fluid level should be even with the bottom of the hole. Parts” in “Maintaining Your Vehicle” for further informa- Use this plug to add fluid as required. tion.
Page 504 502 MAINTAINING YOUR VEHICLE passable in snow and ice, and chemicals that are sprayed • Insects, tree sap and tar. on trees and road surfaces during other seasons, are • Salt in the air near seacoast localities. highly corrosive to the metal in your vehicle. Outside •...
Page 505 MAINTAINING YOUR VEHICLE 503 • If you detect any stone chips or scratches in the paint, CAUTION! touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • Do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will •...
Page 506 504 MAINTAINING YOUR VEHICLE Wheel And Wheel Trim Care CAUTION! • All wheels and wheel trim, especially aluminum and Do not use scouring pads, steel wool, a bristle brush, chrome plated wheels, should be cleaned regularly or metal polishes. Do not use oven cleaner. These with a mild soap and water to prevent corrosion.
Page 507 MAINTAINING YOUR VEHICLE 505 • For tough stains, apply MOPAR® Total Clean, or a Your leather upholstery can be best preserved by regular mild soap solution to a clean, damp cloth and remove cleaning with a damp soft cloth. Small particles of dirt stain.
Page 508 506 MAINTAINING YOUR VEHICLE Cleaning Headlights CAUTION! Your vehicle is equipped with plastic headlights and fog Direct contact of air fresheners, insect repellents, lights that are lighter and less susceptible to stone break- suntan lotions, or hand sanitizers to the plastic, age than glass headlights.
Page 509 MAINTAINING YOUR VEHICLE 507 cleaner. Use caution when cleaning the inside rear win- Seat Belt Maintenance dow equipped with electric defrosters or windows Do not bleach, dye, or clean the belts with chemical equipped with radio antennas. Do not use scrapers or solvents or abrasive cleaners.
Page 510: Fuses
508 MAINTAINING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) not disassemble or modify the system. Seat belt rating as the original fuse. Never replace a fuse assemblies must be replaced after a collision if they with another fuse of higher amp rating. Never have been damaged (i.e., bent retractor, torn web- replace a blown fuse with metal wires or any other bing, etc.).
Page 511: Front Power Distribution Center (Fuses)
MAINTAINING YOUR VEHICLE 509 Front Power Distribution Center (Fuses) CAUTION! The Front Power Distribution Center is located in the • When installing the power distribution center engine compartment. This module contains fuses and cover, it is important to ensure the cover is properly relays.
Page 512 510 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Mini-Fuse Description – – Fuse – Spare 40 Amp Green – Radiator Fan #1 – If Equipped 50 Amp Red – Power Steering #1 / Radiator Fan (6.2L Super- charged) – If Equipped 30 Amp Pink –...
Page 513 MAINTAINING YOUR VEHICLE 511 Cavity Cartridge Fuse Mini-Fuse Description – – Fuse – Spare – 20 Amp Yellow Left HID – If Equipped – 20 Amp Yellow Right HID – If Equipped 50 Amp Red – Radiator Fan #2 – If Equipped 50 Amp Red –...
Page 514 512 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Mini-Fuse Description – – Fuse – Spare – 25 Amp Clear Engine Module – – Fuse – Spare – – Fuse – Spare – 25 Amp Clear Powertrain #1 – 20 Amp Yellow Powertrain #2 –...
Page 515: Rear Power Distribution Center (Fuses)
MAINTAINING YOUR VEHICLE 513 Cavity Cartridge Fuse Mini-Fuse Description – 20 Amp Yellow Vacuum Pump – 5 Amp Tan Adaptive Cruise (LD/LX) – If Equipped – – Fuse – Spare Rear Power Distribution Center (Fuses) There is also a power distribution center located in the trunk under the spare tire access panel.
Page 516 514 MAINTAINING YOUR VEHICLE CAUTION! • When installing the power distribution center cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the power distribution center and possibly result in an electrical system failure.
Page 517 MAINTAINING YOUR VEHICLE 515 Cavity Cartridge Fuse Mini-Fuse Description 60 Amp Yellow — Front PDC Feed #2 30 Amp Pink — Sunroof / Dome Lamp – Police 40 Amp Green — Exterior Lighting #1 40 Amp Green — Exterior Lighting #2 30 Amp Pink —...
Page 518 516 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Mini-Fuse Description — — Fuse — Spare 30 Amp Pink (6.2L Su- — Fuel Pump (6.2L Supercharged) percharged) Fuel Pump (LD STD) 25 Amp Clear (LD STD) — 20 Amp Yellow – Police Right Spot Lamp –...
Page 519 MAINTAINING YOUR VEHICLE 517 Cavity Cartridge Fuse Mini-Fuse Description — 25 Amp Clear Amplifier – If Equipped — 25 Amp Breaker Power Seats — 15 Amp Blue HVAC Module/Cluster — 15 Amp Blue Ignition Switch/RF hub Module/Steering Column Lock-LX If Equipped —...
Page 520 518 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Mini-Fuse Description — — Fuse — Spare — — Fuse — Spare 30 Amp Pink — Rear Defrost — 20 Amp Yellow Rear Heated Seats/Steering Wheel Module — 10 Amp Red Park Assist / Blind Spot / Rear View Camera —...
Page 521 MAINTAINING YOUR VEHICLE 519 Cavity Cartridge Fuse Mini-Fuse Description — — Fuse — Spare — 20 Amp Yellow Front Heated Seats – If Equipped — 10 Amp Red Heated Cupholders/Rear Heated Seat Switches – If Equipped — 10 Amp Red HVAC Module/In Car Tempera- ture Sensor —...
Page 522 520 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Mini-Fuse Description — 20 Amp Yellow Cigar Lighter (LA) – If Equipped — — Fuse — Spare — — Fuse — Spare — 25 Amp Breaker Rear Windows (LD/LX) — 10 Amp Red Airbag Module —...
Page 523: Vehicle Storage
MAINTAINING YOUR VEHICLE 521 in the fresh air and high blower setting. This will VEHICLE STORAGE ensure adequate system lubrication to minimize the If you are leaving your vehicle dormant for more than 21 possibility of compressor damage when the system is days, you may want to take these steps to protect your started again.
Page 524 522 MAINTAINING YOUR VEHICLE Bulb Number Shift Indicator Lamp JKLE14140 Optional Door Map Pocket/Cupholder LED (Serviced at Authorized Dealer) For lighted switches, see your authorized dealer for replacement instructions. Exterior Bulbs Bulb Number Low Beam/High Beam (Bi-Halogen Headlamp) HIR2LL Low Beam/High Beam (Bi-Xenon Headlamp) D3S (Serviced at Authorized Dealer) Front Turn Signal Lamp PSY24WSV...
Page 525: Bulb Replacement
MAINTAINING YOUR VEHICLE 523 Bulb Number Backup Lamp LED (Serviced at Authorized Dealer) Center High Mount Stop Lamp (CHMSL) LED (Serviced at Authorized Dealer) License LED (Serviced at Authorized Dealer) Rear Fog Lamp – If Equipped LED (Serviced at Authorized Dealer) headlamp switch off and the ignition turned to the OFF BULB REPLACEMENT position.
Page 526 524 MAINTAINING YOUR VEHICLE NOTE: On vehicles equipped with HID headlamps, 5. Disconnect the bulb from the wiring assembly and when the headlamps are turned on, there is a blue hue to install the replacement bulb. the lights. This diminishes and becomes more white after 6.
Page 527: Front Turn Signal Lamps
MAINTAINING YOUR VEHICLE 525 5. Disconnect the bulb from the wiring connector and Front Turn Signal Lamps install the replacement bulb. 1. Open the hood. 6. Install the bulb and connector assembly straight into NOTE: Removal of the air cleaner filter housing may be the lamp until it locks in place.
Page 528: Front/Rear Side Marker Lamp
526 MAINTAINING YOUR VEHICLE Front/Rear Side Marker Lamp License Lamp The Side Markers use LED lamps that are not serviceable The License Lamp uses an LED source that is not separately. The Side Markers must be replaced as an serviceable separately. The License Lamp must be re- assembly, see your authorized dealer.
Page 529: Fluid Capacities
MAINTAINING YOUR VEHICLE 527 FLUID CAPACITIES U.S. Metric Fuel (Approximate) All Engines 18.5 Gallons 69.9 Liters Engine Oil With Filter 3.6 Liter Engine (SAE 5W-20, API Certified) 6 Quarts 5.6 Liters 5.7 Liter Engine (SAE 5W-20, API Certified) 7 Quarts 6.6 Liters Cooling System * 3.6 Liter Engine –...
Page 530: Fluids, Lubricants, And Genuine Parts
Mile Formula OAT (Organic Additive Technology). Engine Oil We recommend you use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395 such as MOPAR®, Pennzoil®, and Shell Helix®. Refer to your engine oil filler cap for correct SAE grade.
Page 531 MAINTAINING YOUR VEHICLE 529 CAUTION! CAUTION! (Continued) • Do not use water alone or alcohol-based engine • Mixing of engine coolant (antifreeze) other than coolant (antifreeze) products. Do not use additional specified Organic Additive Technology (OAT) en- rust inhibitors or antirust products, as they may not gine coolant (antifreeze), may result in engine be compatible with the radiator engine coolant and damage and may decrease corrosion protection.
Page 532: Chassis
530 MAINTAINING YOUR VEHICLE Chassis Component Fluid, Lubricant, Or Genuine Part Automatic Transmission – 8-Speed Transmission Use only MOPAR® ZF 8&9 Speed ATF™ Automatic Transmission Fluid, or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission.
Page 533: Maintenance Schedules
MAINTENANCE SCHEDULES CONTENTS MAINTENANCE SCHEDULE ... . .532 ▫ Maintenance Chart.....534 I n f o r ma t i o n P r o v i d e d b y :...
Page 534 532 MAINTENANCE SCHEDULES The “Oil Change Required” message will be displayed in MAINTENANCE SCHEDULE the DID and a single chime will sound, indicating that an Your vehicle is equipped with an automatic oil change oil change is necessary. indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for Your authorized dealer will reset the oil change indicator scheduled maintenance.
Page 535 MAINTENANCE SCHEDULES 533 Once A Month Or Before A Long Trip: At Every Oil Change Interval As Indicated By Oil Change Indicator System: • Check engine oil level • Change oil and filter • Check windshield washer fluid level • Rotate the tires. Rotate at the first sign of irregular •...
Page 536 534 MAINTENANCE SCHEDULES Maintenance Chart Mileage or time passed (whichever comes first) Or Years: 2 Or Kilometers: Additional Inspections Inspect the CV joints. Inspect front suspension, tie rod ends, boot seals, and replace if necessary. Inspect the rear axle fluid. Inspect the front axle fluid (All Wheel Drive Only).
Page 537 MAINTENANCE SCHEDULES 535 Mileage or time passed (whichever comes first) Or Years: 2 Or Kilometers: Additional Maintenance Replace engine air filter. Replace cabin/air conditioning filter. Replace spark plugs.** Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first.
Page 538 536 MAINTENANCE SCHEDULES Mileage or time passed (whichever comes first) Or Years: 2 Or Kilometers: Change the rear axle fluid and on models equipped with All Wheel Drive (AWD) change the front axle fluid if using your vehicle for any of the following: police, taxi, fleet, off-road, or frequent trailer towing.
Page 539 MAINTENANCE SCHEDULES 537 WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
Page 540 I n f o r ma t i o n P r o v i d e d b y :...
Page 541 ▫ FCA US LLC Customer Center ... .541 DEPARTMENT OF TRANSPORTATION UNIFORM ▫ Chrysler Canada Inc. Customer Center ..541 TIRE QUALITY GRADES ....546 ▫...
Page 542: Suggestions For Obtaining Service For Your Vehicle
540 IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR Be Reasonable With Requests YOUR VEHICLE If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with Prepare For The Appointment the service advisor and list the items in order of priority.
Page 543: Fca Us Llc Customer Center
Phone: (800) 247-9753 They want to know if you need assistance. • If an authorized dealer is unable to resolve the con- Chrysler Canada Inc. Customer Center cern, you may contact the manufacturer’s customer P.O. Box 1621 center.
Page 544: In Mexico Contact
542 IF YOU NEED CONSUMER ASSISTANCE Canadian residents with hearing difficulties that require In Mexico Contact assistance can use the special needs relay service offered Av. Prolongacion Paseo de la Reforma, 1240 by Bell Canada. For TTY teletypewriter users, dial 711 Sante Fe C.P.
Page 545: Warranty Information
IF YOU NEED CONSUMER ASSISTANCE 543 The manufacturer will not stand behind any service WARNING! contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the Engine exhaust (internal combustion engines only), manufacturer’s service contract.
Page 546: Mopar® Parts
544 IF YOU NEED CONSUMER ASSISTANCE campaign. However, NHTSA cannot become involved in MOPAR® PARTS individual problems between you, your authorized MOPAR® fluids, lubricants, parts, and accessories are dealer, and the manufacturer. available from an authorized dealer. They are recom- mended for your vehicle in order to help keep the vehicle To contact NHTSA, you may either call the Auto Safety operating at its best.
Page 547: Publication Order Forms
IF YOU NEED CONSUMER ASSISTANCE 545 Diagnostic Procedure Manuals PUBLICATION ORDER FORMS To order the following manuals, you may use either the Diagnostic Procedure Manuals are filled with diagrams, website or the phone numbers listed below. Visa, Mas- charts and detailed illustrations. These practical manuals tercard, American Express, and Discover orders are ac- make it easy for students and technicians to find and fix cepted.
Page 548: Department Of Transportation Uniform Tire Quality Grades
546 IF YOU NEED CONSUMER ASSISTANCE Call toll free at: Treadwear The Treadwear grade is a comparative rating, based on • 1-800-890-4038 (U.S.) the wear rate of the tire when tested under controlled • 1-800-387-1143 (Canada) conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded Visit us on the Worldwide Web at:...
Page 549: Temperature Grades
IF YOU NEED CONSUMER ASSISTANCE 547 Vehicle Safety Standard No. 109. Grades B and A repre- WARNING! sent higher levels of performance on the laboratory test wheel, than the minimum required by law. The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not WARNING! include acceleration, cornering, hydroplaning, or...
Page 550 I n f o r ma t i o n P r o v i d e d b y :...
Page 551 INDEX I n f o r ma t i o n P r o v i d e d b y :...
Page 552 550 INDEX About Your Brakes ......361 Maintaining Your Air Bag System ... .69 ABS (Anti-Lock Brake System) .
Page 553 INDEX 551 Alarm System (Security Alarm) ....17 Fluid Level Check ..... . .499 All Wheel Drive (AWD).
Page 554 552 INDEX Brake Fluid ......530 Carbon Monoxide Warning ....95 Brake, Parking .
Page 555 Cupholders ......246 UCI ....... . .300 Customer Assistance .
Page 556 554 INDEX Customer Programmable Features ... . .277 Door Locks Child-Protection Door Lock — Rear Doors ..31 Data Recorder, Event ..... . .70 Door Locks .
Page 557 INDEX 555 Electric Rear Window Defrost....255 Air Cleaner ......481 Electric Remote Mirrors .
Page 558 556 INDEX Temperature Gauge ..... .263 Flashers Engine Oil Viscosity ..... . .479 Hazard Warning .
Page 559 INDEX 557 Cooling System ......491 Specifications ......528 Engine Oil .
Page 560 558 INDEX GVWR ....... . .425 Head Rests ......134 Heated Mirrors .
Page 561 Enter The Trunk ......21 iPod®/USB/MP3 Control ....300 Lock The Vehicle’s Doors .
Page 562 560 INDEX Latches ....... . .98 Hazard Warning Flasher ....442 Hood .
Page 563 INDEX 561 Seat Belt Reminder ..... .263 Low Tire Pressure System ....402 Security Alarm .
Page 564 562 INDEX Outside ......112 Disposal ......480 Rearview .
Page 565 INDEX 563 Panic Alarm ......22 Pregnant Women And Seat Belts ....52 Parking Brake.
Page 566 564 INDEX Rear Window Features .....255 Unlatch The Trunk ..... . .21 Recorder, Event Data .
Page 567 INDEX 565 Rocking Vehicle When Stuck ....459 Seat Belt System ......42 Rotation, Tires .
Page 568 566 INDEX Height Adjustment ..... .127 Shifting ....... .342 Memory .
Page 569 INDEX 567 Remote .......24 System, Remote Starting .....24 Starting And Operating .
Page 570 568 INDEX Jacking .......445 Towing ....... .426 Life Of Tires .
Page 571 Vehicle Identification Number (VIN) ... . .6 UCI Connector ......300 Vehicle Loading .
Page 572 570 INDEX Vehicle Security Alarm (Security Alarm) ..17 Wheel And Wheel Trim Care ....504 Vehicle Storage ......313 Wind Buffeting.
Page 573 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this The antenna cable should be as short as practical and vehicle’s electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use frequency signals. Mobile two-way radios and telephone only fully shielded coaxial cable.
Page 574 FCA US LLC 15C481-126-AC Third Edition Printed in U.S.A. I n f o r ma t i o n P r o v i d e d b y :...

Chrysler 300 Owner's Manual

Introduction

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

Quick Links

Chapters

Related Manuals for Chrysler 300

Summary of Contents for Chrysler 300