Makita LS1440 Instruction Manual
Hide thumbs
Also See for LS1440:
- Instruction manual (97 pages) ,
- Instruction (37 pages) ,
- Instruction manual (69 pages)
Related Manuals for Makita LS1440
Summary of Contents for Makita LS1440
- Page 1 INSTRUCTION MANUAL Miter Saw LS1440 012687 DOUBLE INSULATION IMPORTANT: Read Before Using.
-
Page 2: Specifications
ENGLISH (Original instructions) SPECIFICATIONS Blade diameter 355 mm Blade body thickness 2.0 mm - 2.6 mm Hole diameter 25 mm and 25.4 mm Max. Miter angle Left 45° , Right 45° Max. Cutting capacities (H x W) Miter angle 0° 45°... -
Page 3: For Safe Operations
Makita Corporation responsible Do not force the tool. manufacturer declare that the following Makita It will do the job better and safer at the rate for machine(s): which it was intended. Designation of Machine: Use the right tool. -
Page 4: Additional Safety Rules For Tool
by an authorized service facility. Inspect extension Do not operate saw without guards in place. cords periodically and replace, if damaged. Keep Check blade guard for proper closing before handles dry, clean and free from oil and grease. each use. Do not operate saw if blade guard 15. -
Page 5: Installation
23. Stop operation immediately if you notice INSTALLATION anything abnormal. 24. Do not attempt to lock the trigger in the on Bench mounting position. When the tool is shipped, the handle is locked in the 25. Be alert at all times, especially during lowered position by the handle latch. -
Page 6: Functional Description
When cleaning is complete, reverse procedure above and secure bolt. Do not remove spring holding blade guard. If guard becomes discolored through age or UV light exposure, contact a Makita 001540 service center for a new guard. DO NOT DEFEAT OR This tool is factory adjusted to provide the maximum REMOVE GUARD. -
Page 7: Adjusting The Miter Angle
the blade extends slightly below the top surface of the Switch action turn base at the point where the front face of the guide For tools with lock lever fence meets the top surface of the turn base. With the tool unplugged, rotate the blade by hand while 1. - Page 8 CAUTION: Always be sure that the tool is switched off and • unplugged before installing or removing the blade. Use only the Makita socket wrench provided to • 002860 install or remove the blade. Failure to do so may result in overtightening or insufficient tightening of the hex bolt.
-
Page 9: Securing Workpiece
NOTE: topmost position, then fasten securely. If the vise knob is If you connect a Makita vacuum cleaner to your saw, forced in or pulled out while being turned clockwise, the more efficient and cleaner operations can be performed. -
Page 10: Operation
The vertical vise can be installed in the position on either position to cut the workpiece. When the cut is the left or right side of the guide fence. Insert the vise rod completed, switch off the tool and WAIT UNTIL into the hole in the guide fence and tighten the screw to THE BLADE HAS COME TO A COMPLETE STOP secure the vise rod. -
Page 11: Carrying Tool
Carrying tool 10mm Over 480mm 1. Handle latch 45mm 70mm 70mm 150mm 150mm 1. Hole 012667 002147 Make sure that the tool is unplugged. Secure the turn CAUTION: base at right miter angle fully by means of the grip. Lower Use straight wood of even thickness as the wood •... -
Page 12: Replacing Carbon Brushes
Adjusting for smooth handle action 1. Hex bolt 1. Gear housing 2. Hex lock nut 3. Arm 002162 Loosen the grip which secures the turn base. Turn 002161 the turn base so that the pointer points to 0° on the The hex lock nut which holds the gear housing and the miter scale. -
Page 13: Optional Accessories
Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center. Carbide-tipped saw blades • Socket wrench 13 • Holder set •... - Page 16 Makita Corporation Anjo, Aichi, Japan www.makita.com 883619B224...