Bosch Uneo Maxx Original Instructions Manual page 13

OBJ_BUCH-1190-005.book Page 13 Monday, March 23, 2015 8:49 AM
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signif-
icantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from
the effects of vibration such as: maintain the tool and the acces-
sories, keep the hands warm, organisation of work patterns.
Technical Data
Cordless Rotary Hammer
Article number
Rated voltage
Rated speed
Impact rate
Impact energy per stroke according
to EPTA-Procedure 05/2009
Tool holder
Max. drilling dia.
– Concrete (with twist drill)
– Steel
– Wood
– Wood (with spade bits Self Cut)
Weight according to
EPTA-Procedure 01/2003
Permitted ambient temperature
– during charging
*
– during operation and during
storage
Recommended batteries
Recommended chargers
– PBA 18V ....V-.
– PBA 18V ....W-.
* Limited performance at temperatures <0 °C
Technical data determined with battery from delivery scope.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2009/125/EC (Regulation
1194/2012), 2011/65/EU, until 19 April 2016:
2004/108/EC, from 20 April 2016 on: 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 60745-1, EN 60745-2-6.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 23.03.2015
Bosch Power Tools
Assembly
 Before any work on the machine (e. g., maintenance,
tool change, etc.) as well as during transport and stor-
age, set the rotational direction switch to the centre
position. Unintentional actuation of the On/Off switch can
lead to injuries.
Battery Charging (see figure A)
 Use only the chargers listed in the technical data. Only
Uneo Maxx
these chargers are matched to the lithium-ion battery of
3 603 J52 3..
your power tool.
V= 18
Note: The battery supplied is partially charged. To ensure full
-1
min 0–900
capacity of the battery, completely charge the battery in the
-1
min 0–5000
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
J 0.6
ducing its service life. Interrupting the charging procedure
SDS-Quick
does not damage the battery.
The lithium-ion battery is protected against deep discharging
mm 10
by the "Electronic Cell Protection (ECP)". When the battery is
mm 8
empty, the machine is switched off by means of a protective
mm 10
circuit: The inserted tool no longer rotates.
mm 20
 Do not continue to press the On/Off switch after the
machine has been automatically switched off. The bat-
kg 1.4
tery can be damaged.
To remove the battery 10, press the battery unlocking button
°C 0...+45
18 and pull the battery out of the power tool toward the rear.
Do not exert any force.
°C –20...+50
Observe the notes for disposal.
PBA 18V ....V-.
Selecting Tools
PBA 18V ....W-.
For hammer drilling, SDS-Quick tools are required.
For drilling without impact in wood, metal, ceramic and plas-
AL 22.. CV
tic, a suitable SDS-Quick tool or an application tool with hexa-
AL 18.. CV
gon shank can be used.
AL 18.. CV
For screwdriving, use only screwdriver bits with ball catch 14
(DIN 3126-E6.3). Other screwdriver bits 13 can be inserted
via a universal bit holder with ball catch 12.
A selection of suitable application tools can be found in the
Accessories Overview at the end of these instructions.
Changing the Tool
out at no-load. However, this has no effect on the accuracy of
the drill hole, as the drill bit centres itself during drilling.
The SDS-Quick tool holder can also accommodate different
drill-bit types with hexagon shank. For more information, see
the accessories page at the end of these operating instructions.
The dust protection cap 2 largely prevents the entry of drilling
dust into the tool holder during operation. When inserting the
tool, take care that the dust protection cap 2 is not damaged.
 A damaged dust protection cap should be changed im-
mediately. We recommend having this carried out by
an after-sales service.
English | 13
The SDS-Quick tool holder allows for simple
and convenient changing of drilling tools with-
out the use of additional tools.
Due to their working principle, SDS-Quick drill-
ing tools move freely. This results in radial run-
1 609 92A 13S | (23.3.15)