Related Manuals for Paramount Fitness XFW8100
Summary of Contents for Paramount Fitness XFW8100
- Page 1 Unit shown with optional band pegs and band storage posts. XFW8100 NSTALLATION ANUAL AM-XFW8100 REV: 053014...
- Page 2 1-800-721-2121 or 1-323-721-2121 Office hours are Monday-Friday, 7:30 am - 4:30 pm PST Or email us at nasales@paramountfitness.com Thank You for your patronage. Paramount Fitness Corporation 6450 East Bandini Blvd. Los Angeles, CA 90040 WARNING SERIOUS INJURIES TO USERS, BYSTANDERS OR INSTALLERS CAN OCCUR IF THE INSTRUCTIONS AND WARNINGS CONTAINED IN THIS MANUAL ARE NOT FOLLOWED.
-
Page 3: Table Of Contents
ABLE ONTENTS ......................AFETY ..............ENERAL ARE AND AINTENANCE & W ............... ACHINE IMENSIONS EIGHTS ..................... ARTON ONTENTS ......................SSEMBLY ................... NCHORING TO THE LOOR & F ..................ERVICE INAL HECK ....................ARTS IAGRAMS & W ..............NTENDED ARNING ABELS ................. -
Page 4: Safety
AFETY ACILITY AND AFETY RECAUTIONS 1. Review and understand all of the warning labels affixed to this machine and on the facility safety sign. 2. Be certain that the machine operation is understood before it is used. Refer to the instructional Procedure Label affixed to the machine. - Page 5 AFETY 12d. This equipment is designed for standard olympic size weight plates with a 50mm bore (1.9”). 12e. Do not exceed the maximum weight capacity of the machine. Maximum plate size is 45 lbs. (25 kg.). 13. On Selectorized and Cable equipped machines: 13a.
- Page 6 AFETY AINTENANCE AFETY RECAUTIONS 1. Refer to Maintenance Schedule label on the machine as well as this manual for when to perform maintenance. 2. Check the function of your machine DAILY by verifying the following: • Inspect cables and end fittings for any signs of wear. Replace if worn, frayed or damaged with original Paramount replacement components.
- Page 7 13. Be sure all hardware is tight before using the machine. Retain these instructions for future reference. If you have any questions, do not hesitate to contact your Paramount dealer or Paramount Fitness Corp. at (800)721-2121 or nasales@paramountfitness.com.
- Page 8 IMENSIONS AND EIGHTS Carton 1 dimensions: 92.7” X 29.3” X 6.7” 236 cm x 74.5 cm x 17 cm Carton Weight (as shipped) = 205 lbs (93 kg.) Carton 2 dimensions: 92.7” X 29.3” X 6.7” 236 cm x 74.5 cm x 17 cm Carton Weight (as shipped) = 205 lbs (93 kg.) Assembled Weight (as shown) = 345 lbs (157 kg) Maximum Load Capacity = 500 LBS.
-
Page 9: Carton Contents
ARTON ONTENTS XFW8100-CTN1 ( XFW8100-CTN2 ( LEFT SIDE RIGHT SIDE... -
Page 10: Assembly
RAME SSEMBLY Completely assemble the frame as shown, keeping the hardware loose until the entire frame is assembled. Incrementally tighten the hardware in several passes around the machine. DO NOT insert and fully tighten hardware at one junction, then proceed to the next. - Page 11 RAME SSEMBLY...
- Page 12 PTIONAL If you have purchased the optional band peg kit, install it now. To install the band storage posts, remove the plastic end plug from two of the weight storage posts. Slide the weight storage posts into upper frame as shown below and then slide the band storage post into the weight storage post, aligning the 10 mm (3/8”) holes in both posts with the hole in the frame.
- Page 13 INAL SSEMBLY Note: The olympic bar holder can be placed on either the outer left/right or inner left/right of the base frame.
-
Page 14: Anchoring To The Floor
NCHORING TO THE LOOR Shown below are the provisions in the frame for anchoring the machine to the floor. Paramount strongly recommends that all equipment be anchored to the floor to prevent movement and increase stability. • Due to the wide variation of flooring on which the unit can be installed, contact a qualified contractor to determine an appropriate fastening system for your floor. - Page 15 & S INAL HECK ERVICE I N A L H E C K 1. Verify that all hardware is tight. 2. Verify that the machine is stable and that all four feet are in contact with the floor. If a foot is raised off the floor, loosen all of the frame connection bolts and retighten them incrementally in a different sequence.
-
Page 16: Parts Diagrams
ARTS IAGRAMS... - Page 17 ARTS IAGRAMS...
- Page 18 ARTS IAGRAMS...
- Page 19 ARTS IAGRAMS...
- Page 20 ARTS IAGRAMS...
-
Page 21: Ntended Se Arning Abels
& W NTENDED ARNING ABELS INTENDED USE 1. This unit is intended to support Olympic bars in multiple positions facilitating press, squat, row or dead lift exercises. 2. The long bar stops must be used when performing squat or pressing movements. Adjust their position based on the exercise, user size and range desired.