Table of Contents
Advertisement
[On]
Selecting the source type
Select the mode to link selection of key source signal with key fill selection. The selection status is stored for each source signal.
1
Select the <ME1>/<ME2> button → [KEY1] to [KEY4] → [Key Setting] tab.
2
Select an item in [Source Type] in the [Key] column.
[Self Key]
[External Key]
Selecting the fill type
Select the fill type.
1
Select the <ME1>/<ME2> button → [KEY1] to [KEY4] → [Key Setting] tab.
2
Select an item in [Fill] in the [Key] column.
[Bus]
[Matte]
Setting the matte color
Set the fill matte color.
1
Select the <ME1>/<ME2> button → [KEY1] to [KEY4] → [Key Setting] tab.
2
Adjust the color.
f Set [Hue], [Sat], [Lum], or [Color Palette] in the [Fill Matte] column.
Selecting the key source
Use the KEY bus crosspoint buttons to select key sources for the keys specified using the KEY bus selector buttons.
Setting the link between key fill signal and key source signal
To link the selection of key fill signal and key source signal, select the <CONF> button on the top menu → [SOURCE LINK] → [Key Assign] tab →
[Master/Slave], and set [Fill to Source] or [Source to Fill].
For details, refer to "Setting the key coupling" (page 120).
f [Fill to Source]: When the key fill signal (master) is selected, the key source signal (slave) changes automatically.
f [Source to Fill]: When the key source signal (master) is selected, the key fill signal (slave) changes automatically.
Selecting the key fill signal and the key source signal separately
Use the <BUS SHFT> button to temporarily enable selection of a source different from the link setting using the KEY bus crosspoint buttons.
r When [Fill to Source] is set
Key fill signal: When the KEY bus crosspoint buttons are selected without pressing the <BUS SHFT> button, a key fill signal can be selected. At this
time, the KEY but selector buttons light in Low tally color.
Key source signal: When the KEY bus selector buttons are pressed while the <BUS SHFT> button is held down, the KEY bus selector buttons light in
Preset tally color, and key source different from the link setting can be selected using the KEY bus crosspoint buttons. The changed key source is not
stored as the link setting, and the source returns to the linked source when another key fill source is selected. If the <BUS SHFT> button is pressed and
turned off, select the key fill signal (master) again.
r When [Source to Fill] is set
Key source signal: When the KEY bus crosspoint buttons are selected without pressing the <BUS SHFT> button, a key source signal can be selected.
At this time, the KEY but selector buttons light in Preset tally color.
Key fill signal: When the KEY bus selector buttons are pressed while the <BUS SHFT> button is held down, the KEY bus selector buttons light in Low
tally color. A key fill source different from the link setting can be selected using the KEY bus crosspoint buttons. The changed key fill source is not stored
as the link setting, and the source returns to the linked source when another key source material is selected. If the <BUS SHFT> button is pressed and
turned off, select the key source signal (master) again.
Key transitions
Operating in the transition area
1
Select the transition target.
f Use the <KEY1> to <KEY4> buttons to select a transition target. To select multiple targets, press the <BKGD> button and the <KEY1> to <KEY4>
buttons simultaneously.
Chapter 5 Basic Operations — KEY
Does not cut key fill with a key signal. The part of key fill not cut out with the key signal is superimposed on the
background image. This item is used when key fill source has been cut with a key signal beforehand using an external
device.
Uses the source selected in the key fill bus column as the key source signal.
Always uses an external key. The source signal for fill is set using [Fill] in the [Key] column.
Uses the bus signal for the key fill signal.
Uses the internal fill matte for the key fill signal. The color set in the [Fill Matte] column is used for the fill matte color.
– 52 –
Advertisement
Table of Contents
