Miele KFN 14943 SD Installation Instructions Manual
Hide thumbs
Also See for KFN 14943 SD:
- Operating and installation instructions (68 pages) ,
- Operating and installation manual (64 pages) ,
- Operating and installation instructions (18 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Miele KFN 14943 SD
Summary of Contents for Miele KFN 14943 SD
-
Page 1: Installation Instructions
Installation Instructions KFN 14943 SD en - CA Installation, repair and maintenance work should be performed by a Miele authorized service technician in accordance with national and local safety regulations and the provided installation instructions. -
Page 2: Electrical Information
If any changes are needed to the electrical connection of this appliance household wiring or power supply, this to the power supply, please consult a work must be performed by a qualified licensed electrician or call the Miele electrician. Technical Service. V 1-800-565-6435... -
Page 3: Installation Information
Installation information If the room is too cold, it will cause the Do not place any devices that cooling system in the appliance to produce heat (such as a toaster or remain off for too long. This may lead to microwave) on top of the appliance. - Page 4 Installation information Adjustments ^ Use the wrench provided to adjust the front feet as needed, so that the appliance is levelled. Supporting the appliance door ^ In any case unscrew foot a until it is on the ground. Then unscrew the foot another 90°.
- Page 5 Installation information Appliance dimensions KFN 14943 SD ed/cs 2020 mm 747 mm 630 mm 1330 mm 790 mm (79 17/32") (29 3/8") (24 13/16") (52 3/8") (31 3/32") If the gap between the rear of the appliance and the wall is less than 2 inch...
-
Page 6: Changing The Door Hinging
Changing the door hinging The appliance comes with right-hand hinging. If left-hand door hinging is required, the door hinge must be changed: You will need the following tools to change the door hinging: – a Phillips screwdriver, – a flathead screwdriver, –... - Page 7 Changing the door hinging Before changing the hinging, remove any items of food from the shelves in the appliance door. Removing the top soft-close mechanism: ^ Open the top door of the appliance. ^ Slide panel a in the direction of the appliance and leave it hanging between the door and the appliance.
- Page 8 Changing the door hinging ^ Remove cover d. Removing the top door of the appliance: Now the soft-close mechanism and the appliance are no longer connected. ^ Remove panel a. ^ Loosen the cover h by carefully sliding a flathead screwdriver from ^ Push the shock absorber arm f as below into the recess.
- Page 9 Changing the door hinging Caution! The top door of the Be careful not to damage the door appliance is no longer secured as seal. soon as the hinge bracket is If the door seal is damaged, the removed! appliance door may not close properly and there will not be ^ Close the top door of the appliance.
- Page 10 Changing the door hinging ^ Put the spacer aside. Removing the bottom door of the appliance: ^ Close the bottom door of the appliance. ^ Push pin e up and out. Now the soft-close mechanism and the appliance are no longer connected. ^ Remove panel a.
- Page 11 Changing the door hinging ^ Unscrew the bearing mechanism g from the hinge bracket h, turn it 180° and screw it into the opposite hole of the hinge bracket. ^ Insert the plug d in the other hole. ^ Remove cover h. ^ Remove screw i and insert it in the outermost hole on the opposite side.
- Page 12 Changing the door hinging ^ Hook the spacer on the handle side into the retainer (A). ^ Insert the bearing pin i in the centre ^ Hook the soft-close mechanism into of the appliance through the hinge bracket k into the bottom door of the the retainer (B) on the appliance side.
- Page 13 Changing the door hinging Mounting the top door of the appliance: ^ Place the top door of the appliance on the bearing pin i in the middle of the appliance. ^ Close the top door of the appliance. ^ Hang the panel b on the shock absorber arm d.
- Page 14 Changing the door hinging Mounting the top soft-close mechanism: ^ With screw c, attach the spacer and the soft-close mechanism. ^ Remove the cover a from the panel b, turn it 180° and replace it on the other side. ^ Hang the panel b on the shock absorber arm d.
- Page 15 Changing the door hinging ^ Remove the securing device g. The mounting plate c must be positioned on the door housing in such a way that when the door is closed the mounting plate is aligned with the outside wall of the appliance. If this is not the case, ^ turn both of the pre-mounted set screws a with an Allen key until the...
-
Page 16: Aligning The Appliance Doors
Aligning the appliance doors The appliance doors can be aligned Align the top door using the elongated with the appliance housing afterwards. holes in the middle hinge bracket: In the following figure, the appliance door is not closed so that the individual steps can be seen more clearly. -
Page 17: Installing The Appliance
Installing the appliance The ventilation cross-sections must not be blocked or covered in any way. They also need to be dusted/cleaned on a regular basis. If installing with standard kitchen cabinets (max. depth 580 mm), the appliance can be set up directly next to the kitchen cabinet. - Page 18 Alteration rights reserved / 5014 M.-Nr. 10 012 210 / 04 M.-Nr. 10 012 210 / 04 KFN 14943 SD ed/cs To obtain the most recent version of this guide, please visit the website of Miele.