Main Remote Control Functions - Harman Kardon AVR430 Service Manual

AVR430/AVR630

MAIN REMOTE CONTROL FUNCTIONS

c Memory Button: Press this button to enter a
radio station to the AVR 630's preset memory. First,
tune the desired station, and then press this button.
Within five seconds of when you see the station's
frequency flash in the Upper Display Line # and
in the on-screen display, press the numeric keys
for the preset number between 01 and 30 that you
wish to assign to the station. (See page 34 for more
information.)
d Stereo Mode Select Button: Press this button
to select a stereo listening mode. When the button is
pressed so that SURROUND OFF appears in
the Lower Display Line $ , the AVR will operate in a
bypass mode with true, fully analog, two-channel
left/right stereo mode with no surround processing or
bass management, as opposed to other modes where
digital processing is used. When the button is pressed
so that SURROUND OFF appears in the Lower
, and the DSP and SURROUND
Display Line $
OFF Surround Mode Indicators % are lit, you will
enjoy a two-channel presentation of the sound along
with the benefits of bass management. Depending on
whether your system is configured for 5.1 or 6.1/7.1
channels, the next press of the button will cause either
5 CH STEREO or 7 CH STEREO to
appear, and the stereo signal will be routed to all five
(or seven) speakers. (See page 31 for more informa-
tion on stereo playback modes.)
e DTS Neo:6 Mode Select Button: Press this
button to select a DTS Neo:6 mode. (See page 31
for the available DTS Neo:6 options.)
f DTS Digital Mode Select Button: When a
DTS-encoded digital source is playing, each press of
this button will scroll through the available DTS modes.
The specific choice of modes will vary according to
the type of encoding on the disc and your system's
speaker configuration. When a DTS source is not in
use, this button has no function. (See page 31 for the
available DTS digital options.)
g Dolby Mode Select Button: This button is used
to select from the available Dolby Surround modes.
Each press of this button will select one of the Dolby
Pro Logic II modes or Dolby 3 Stereo. When a Dolby
Digital-encoded source is in use, the Dolby Digital
mode may also be selected. (See page 31 for the
available Dolby surround mode options.)
h 6-Channel/8-Channel Input Select: Press this
button to select the device connected to the 6- or 8-
Channel Direct Inputs . (See page 29 for more
40
information.)
14 MAIN REMOTE CONTROL FUNCTIONS
i SPL Select Button: This button activates the
EzSet function to quickly and accurately calibrate the
AVR 630's output levels. When the button is pressed
you will then need to select between automatic EzSet
operation or using the remote as a manual SPL meter
Navigation Button o until
by pressing the
/
⁄ ¤
your choice appears in the remote's LCD display.
Press the Set Button q to enter the setting, and
then follow the instructions as displayed in the LCD
display. (For complete information, see page 26.)
j EzSet Microphone Sensor: The microphone
sensor that is used by the EzSet system is behind the
three slots at the top of the remote control. When
using EzSet to calibrate the AVR 630, be certain that
the slots are not covered. (See page 26 for more
information on using EzSet.)
k Lens: The infrared emitters behind the plastic
lens at the top of the remote communicate the remote
codes to the AVR 630. Be certain that the lens is not
covered when using the remote, and point the lens
toward the AVR for best results. In learning mode, the
remote receives IR codes to be learned through a
sensor behind the lens.
NOTE: DO NOT remove the rubber plug that is supplied
to cover the jack on the upper right side of the remote.
The jack is not active and is reserved for future use.
15
harman/kardon