Sony DVP-C660 Service Ma page 23

QQ
3 7 63 1515 0
Settings for the Speakers (SPEAKER SETUP)
• SUBWOOFER
— NONE: If you do not connect a subwoofer, select
this. This activates the Dolby Digital bass redirection
circuitry and outputs the LFE signals from the front
speakers as long as the front speaker size is set to
"LARGE."
— YES: If you connect a subwoofer, select this to output
the LFE (low frequency effect) channel from the
subwoofer.
* Rear speaker position
Specify the location of the rear speakers for correct
"VIRTUAL REAR SHIFT," "VIRTUAL MULTI REAR" and
"VIRTUAL MULTI DIMENSION" effects. These effects
can be found in "VIRTUAL 3D SURROUND" of the
Control Menu display.
• SIDE: If the location of the rear speakers corresponds to
section A in the illustration below.
• REAR: If the location of the rear speakers corresponds
to section B in the illustration below.
This setting affects only the "VIRTUAL REAR SHIFT,"
"VIRTUAL MULTI REAR" and "VIRTUAL MULTI
DIMENSION" mode.
90°
A A
45°
B B
20°
Notes
• The cut off frequency for the subwoofer is fixed at 120 Hz.
• If your speakers are too small to reproduce low bass
frequencies, please set all speaker settings to "SMALL" and
utilize a subwoofer for low frequency sound.
TE
L 13942296513
68
Controlling Your TV or AV Receiver (Amplifier) with the
Supplied Remote Z
By adjusting the remote signal, you can control your TV
or AV receiver (amplifier) with the supplied remote.
Controlling TVs with the remote
TV/DVD
switch
1 2 3
Number 4 5 6
7 8 9
buttons
0
1
Slide the TV/DVD switch to TV.
2
Hold down ?/1, and enter your TV's manufacturer's
code (see the table) using the number buttons.
3
Release ?/1.
www
.
70
http://www.xiaoyu163.com
x DISTANCE
The default distance setting for the speakers in relation to
the listening position is shown below.
12ft/3.6m 12ft/3.6m
10ft/3.0m 10ft/3.0m
You can vary the distance of each speaker as follows. The
default adjustments are in parentheses. Be sure to change
the value in the setup display when you move the
speakers.
• FRONT (12ft/3.6m)
Front speaker distance can be set in 1 foot (0.3 meter)
increments from 4 to 50 feet (1.2 to 15.2 meters).
Distance is measured from the front speaker to the
listening position.
• CENTER (12ft/3.6m)
Center speaker distance can be set in 1 foot (0.3 meter)
increments. Place the center speaker directly between
the front speakers. You can move it up to 2 feet (0.6
meter) backwards or 5 feet (1.5 meters) forwards if
necessary.
• REAR (10ft/3.0m)
Rear speaker distance can be set in 1 foot (0.3 meter)
increments. Place the speakers behind the listening
position at a distance equal to the front speaker
distance. If necessary you can move the rear speakers
up to 16 feet (5 meters) closer to your listening position.
To return to the default setting
Select the item, then press CLEAR.
Notes
• If each of the front or rear speakers are not placed at an equal
distance from your listening position, set the distance
according to the closest speaker.
• Do not place the rear speakers farther away from your listening
position than the front speakers.
Code numbers of controllable TVs
If more than one code number is listed, try entering them
one at a time until you find the one that works with your
TV.
Manufacturer Code number Manufacturer Code number
Sony (default) 01 Panasonic
?/1
Akai 04 Philco
AOC 04 Philips
Centurion 12 Pioneer
Coronado 03 Portland
Curis-Mathes 12 Quasar
Daytron 12 Radio Shack
Emerson 03,04,14 RCA
Fisher 11 Sampo
General Electric 06, 10 Sanyo
Gold Star 03,04,17 Scott
Hitachi 02,03 Sears
J.C.Penney 04,12 Sharp
JVC 09 Sylvania
KMC 03 Teknika
Magnavox 03,08,12 Toshiba
Marantz 04,13 Wards
MGA/Mitsubishi 04,12,13,17 Yorx
NEC 04, 12 Zenith
Notes
• If you enter a new code number, the code number previously
entered will be erased.
• When you replace the batteries of the remote, the code number
may be reset to the default setting. Reset the appropriate code
number.
x ao
y
i
http://www.xiaoyu163.com
8
x BALANCE
You can vary the balance of the left and right speakers as
follows. Be sure to set "TEST TONE" to "ON" for easy
adjustment (see x TEST TONE below). The default
adjustments are in parentheses.
• FRONT (0dB)
Adjust the balance between the front left and right
speakers (–6dB [L] to +6dB [R], 0.5dB increments).
• REAR (0dB)
Adjust the balance between the rear left and right
speakers (–6dB [L] to +6dB [R], 0.5dB increments).
To return to the default setting
Select the item, then press CLEAR.
x LEVEL
You can vary the level of each speaker as follows. The
front speaker level becomes the criterion for adjusting the
other speakers. Be sure to set "TEST TONE" to "ON" for
easy adjustment (see x TEST TONE below). The default
adjustments are in parentheses.
• CENTER (0dB)
Adjust the level of the center speaker (–6dB to +6dB,
0.5dB increments).
• REAR (0dB)
Adjust the level of the rear speakers (–6dB to +6dB,
0.5dB increments).
• SUBWOOFER (0dB)
Adjust the level of the subwoofer (–10dB to +10dB,
0.5dB increments).
To return to the default setting
Select the item, then press CLEAR.
x TEST TONE
The speakers will emit a test tone. Use this when you use
the 5.1CH OUTPUT connectors and adjust the BALANCE
and LEVEL.
• OFF: The test tone is not emitted from the speakers.
• ON: The test tone is emitted from each speaker in
sequence. When you select one of the "SPEAKER
SETUP" items, the test tone is emitted from both left
and right speakers simultaneously.
Note
When you adjust the speaker settings, the sound cuts off for a
moment.
Q Q
3 6 7 1 3
Controlling the TV
You can control your TV using the buttons below. When
you set the TV/DVD switch to TV, you can also control
the number, ?/1 and ENTER buttons.
TV/DVD
switch
1 2
4 5
06,19
7 8
Number
0
buttons
03,04
08
16
03
06,18
05,14
04,10
By pressing
12 You can
11 ?/1 Turn the TV on or off
12 TV/VIDEO Switch the TV's input source between
the TV and other input sources
07,10,11
VOL
Adjust the volume of the TV
03,05,18
CH
Select the channel of the TV
08,12
Number buttons
Select the channel of the TV
03,08,14
and ENTER
07
Note
03,04,12
Depending on the TV, you may not be able to control your TV or
to use some of the buttons above.
12
15
Controlling AV receivers (amplifiers) with
the remote
TV/DVD
switch
1 2
Number 4 5
7 8
buttons
0
u163
1
Slide the TV/DVD switch to DVD.
2
Hold down ?/1, and enter your AV receiver's
.
manufacturer's code (see the table) using the
number buttons.
3
Release ?/1.
1-17
2 9 9 4 2 8
Adjusting the speaker volume
1
After you stop playback, select "SPEAKER SETUP"
in the setup display.
2
Select "TEST TONE" and set "TEST TONE" to "ON."
You will hear the test tone from each speaker in
sequence.
3
From your listening position, select "BALANCE" or
"LEVEL" and adjust the value of "BALANCE" using
</, and "LEVEL" using M/m.
The test tone is emitted from both left and right
speakers simultaneously.
4
Select "TEST TONE" and set "TEST TONE" to "OFF"
to turn off the test tone.
To adjust the volume of all the speakers at one
time
Use the receiver's (amplifier's) volume control.
1 5 0 5 8 2 9 9 4
Code numbers of controllable AV receivers
(amplifier)
If more than one code number is listed, try entering them
one at a time until you find the one that works with your
AV receiver (amplifier).
?/1
VOL
Manufacturer
3
CH
6 Sony
9
TV/VIDEO
Denon
ENTER
Kenwood
Onkyo
Pioneer
ENTER
Sansui
Technics
Yamaha
Notes
• If you enter a new code number, the code number previously
entered will be erased.
• When you replace the batteries of the remote, the code number
may be reset to the default setting. Reset the appropriate code
number.
Controlling the AV receiver (amplifier)
You can change the volume of the AV receiver (amplifier)
using AV VOL.
?/1
3
6
9 m
Notes
• Depending on the AV receiver (amplifier), you may not be able
to control your AV receiver (amplifier).
co
• You can control the AV receiver (amplifier) regardless of the
position of the TV/DVD switch.
9 9
2 8 9 9
69
Code number
91 (default), 89
84, 85, 86
92, 93
81, 82, 83
99
87
97, 98
94, 95, 96
1 2 3
4 5 6
7 8 9
0
AV VOL
71