Furuno GP-1610CF Operator's Manual

Color gps plotter sounder
Hide thumbs Also See for GP-1610CF:

Advertisement

Quick Links

Color GPS Plotter Sounder
The purpose of this Operator's Guide is to provide the basic operating procedures for this equip-
ment. For more detailed information see the operator's manual.
Waypoint
(Marks important
point (buoy, etc.);
can be set as
destination.)
Chart
(Requires chart
card.)
Mark
(Marks point
of interest,
reef, etc.)
Own ship mark
(Shows current
position.)
Course
Depth
The GP-1610CF is a fully integrated color video sounder, color video plotter and GPS receiver.
To find position, simply turn on the power. As your boat moves its track is inscribed on the
display.
GP-1610CF
PLOTTER
DISPLAY
01
CSE 350.0° SPD 16.8kt
DEP 110 m TMP 1 6 . 0 °C 13:42
POS 34°26.345'N 135°41.232'E
Water temperature
(Requires sensor.)
Sample plotter/sounder display
SOUNDER
DISPLAY
Depth scale
0
(Shown here
in meters.)
50
Course bar
100
Fish school
150
Bottom
Ship's track
50k
200
Sounder frequency
Speed
2D
Position-fixing mode
Time
Position
1

Advertisement

Table of Contents
loading

Summary of Contents for Furuno GP-1610CF

  • Page 1 Water temperature (Requires sensor.) Sample plotter/sounder display The GP-1610CF is a fully integrated color video sounder, color video plotter and GPS receiver. To find position, simply turn on the power. As your boat moves its track is inscribed on the display.
  • Page 2: Safety Instructions

    SAFETY INSTRUCTIONS WARNING CAUTION Do not open the equipment. Use the proper fuse. Hazardous voltage which can Use of a wrong fuse can result in fire or cause electrical shock, burn or permanent equipment damage. serious injury exists inside the equipment.
  • Page 3: Inserting A Chart Card

    Inserting a Chart Card 1 Turn off the power. 2 Open the chart card drive cover at the bottom of the display unit. Screws Cover 3 Insert chart card label side up, arrow forward. Arrow forward EJECT Chart button card 4 Close the chart card drive cover.
  • Page 4 COASTLINE DATA CARD DOES NOT REPLACE THE REQUIREMENT TO USE THE APPROPRIATE PRODUCTS FOR NAVIGATION ACCORDING TO ZOOM ZOOM NATIONAL AND INTERNATIONAL OUT 9 REGULATONS. FURUNO ELECTRIC CO., LTD. CURS CNTR TONE Plotter display (Position being calculated.) POWER BRG+ 232.0° RNG+ 0.00nm ACQ DEP 110m TMP 16 .0°C 13:41...
  • Page 5: Adjusting Tone And Brilliance

    Adjusting Tone and Brilliance 1 Press the TONE key. Adjust tone or brilliance HIGH within 10 seconds, TONE : 5 otherwise the display will be erased. HIGH BRILL : 8 Ten levels of tone are provided. MENU NU/CU 2 Press t or s to adjust tone. Eight levels of brilliance are provided.
  • Page 6: Changing The Display

    Changing the Display There are ten displays. Below is the procedure for how to display the three most common dis- plays. The plotter display is currently shown. This display shows chart, ship’s track (when ship moves), etc. MENU NU/CU BRG+ 232.0° RNG+ 0.00nm 2D DEP 110m TMP 16 .0°C 13:41 34°43.801’N 135°21.163’E...
  • Page 7 Switch to the plotter/sounder 3 Press the PLTR key. display. SELECT PLOTTER MODE Plotter Plotter/Sounder Data Graphic Highway PLTR: Sel ESC: Close MENU NU/CU 4 Press to select Plotter/Sounder. SNDR PLTR AUTO EVENT MOB 7 SELECT PLOTTER MODE GOTO Plotter Plotter/Sounder ZOOM ZOOM...
  • Page 8: How To Use The Cursor

    How to Use the Cursor If the cursor is not displayed press the CURS key. Position Cursor intersection Bearing and range from BRG+ 232.0° RNG+ 0.00nm own ship to DEP 110 m TMP - - .-°C 13:55 Cursor position 34°43.801’N 135°21.163’E cursor in lattitude and longitude...
  • Page 9 Registering Your Harbor By registering your harbor as a waypoint, you can later use it as a destination waypoint, when returning home. Before departing 1 Press the WPT key. register your har- bor as a waypoint. SELECT WPT MODE Confirm that "Own Own Position Position"...
  • Page 10: Setting Destination

    Setting Destination When you set a destination, this unit computes the range, bearing and course to the destination. To display your destination on the screen select a small display range or scale. To set as destina- tion a point which is 20 nm from your harbor do the following: Shrink display range or scale.
  • Page 11 3 Press the ENT key. : Cursor ENT: Set MENU NU/CU ENT twice: complete MENU: SEL Mode SNDR PLTR AUTO EVENT 4 Place cursor on MOB 7 destination. GOTO ZOOM ZOOM OUT 9 5 Press the ENT key twice. CURS CNTR TONE Current position is...
  • Page 12 Sailing for Destination Set the sounder in the "Cruise" mode before leaving the harbor. 1 Press the AUTO key.     AUTO MODE   If Cruise is not in reverse Cruise video press to do so. Fish Manual The Cruise mode sup- presses weak echoes and displays strong echoes (such as the bottom)
  • Page 13: Arriving At Destination

    Arriving at Destination When nearing your destination, expand the range scale and set the sounder in the "Fish mode." Expand the display range or scale. WP801 173.0°   5.2nm CSE 175.0°  SPD 16.8kt DEP 110 m TMP - - .-°C 15:15 POS 33°33.979'N 137°07.290'E MENU NU/CU...
  • Page 14 Searching for Fish This section explains how to search for fish schools. Use 50 kHz frequency to search area for fish. If Fish school the display shows fish (Dense schools echoes switch to appear in red- 200 kHz to obtain dish brown/red;...
  • Page 15 Select the 4 Press the SNDR key. bottom zoom display. SELECT SOUNDER MODE Normal 普通 Marker Zoom Bottom Zoom Bottom Lock A-Scope MENU NU/CU 50kHz 200kHz SNDR PLTR SNDR: Sel ESC: Close AUTO EVENT MOB 7 5 Press twice to GOTO select Bottom Zoom.
  • Page 16: Entering Marks

    Entering Marks Marks may be used to denote the location of fish schools, good fishing spots, reefs, etc.   1 Press the PLTR key. Display the plotter/sounder SELECT PLOTTER MODE mode. Plotter Plotter/Sounder Data Graphic Marks cannot be Highway entered when in MENU NU/CU a sounder mode.
  • Page 17 Changing Mark Shape, Color You may wish to display marks in different shapes and colors to differentiate between reefs and fish schools, for example. The procedure below shows how to change from red circle to green diamond. 200k WP801 170.0°   4.8nm CSE 170.0°...
  • Page 18 3 Press s twice to select "◇". 4 Press twice to select MARK COLOR. MENU NU/CU SNDR PLTR 5 Press s twice to select GREEN. AUTO EVENT MOB 7 GOTO   6 Press the ESC key. ZOOM ZOOM OUT 9 CURS CNTR  ...
  • Page 19 Returning to Harbor Set your harbor as destination, and the course, range and bearing to it are displayed on the screen.   1 Press the GOTO key. Set waypoint 01, which you entered earlier, SELECT GOTO MODE as destination.   WPT List  ...
  • Page 20 5 After arriving, press the Cancel destina- GOTO key. tion; turn off the equipment. SELECT GOTO MODE WPT List MENU NU/CU EVENT List ROUTE List SNDR PLTR Cursor/Route plan ENT: Sel CLR: Release AUTO EVENT ESC: Cancel MOB 7 GOTO 6 Press the CLR key.

Table of Contents