Table of Contents
Advertisement
Supplied
accessories
Please
check
and
identify
the supplied ac-
cessories.
AC
mains
lead
1
p
C-
(For United
Kingdom:
(For
Australia
and
VJA0733)
New
Zealand;
RJA0036-K)
I
I
FM
indoor
antenna
1
p
C
.
(For
United
Kingdom:
(For Australia
and
RSA0007)
New
Zealand:
RSA0006)
AM
loop
antenna
set
(RSA0010)
•AM
loop
antenna
1
p
C
.
•AM
antenna
holder
1
p
C
.
•Screw
!
pc
t
pc.
I
I
Remote
control transmitter
(EUR644340)
[~|
Batteries
(UM-3,
"AA",
R6)
2
pes.
I
|
Notebook-like binder
[Liner
notes
organizer]
(RFA0622-K1)
I
I
Adhesive
number
(RQLA0321)
1
pc.
1
pc.
[
3
Antenna
plug
adaptor
(Supplied
for
United
Kingdom
only:
SJP9009)
t
pc.
Use numbers
indicated
in
parentheses
when
asking
for
replacement
parts.
Concerning
the
remote
control
Battery
installation
Insert
the
batteries with
this unit
as
shown
below.
Use
two
UM-3
"AA",
IEC
R6
(1.5
V) or equivalent
batteries.
Insert
the
batteries
in
the correct
polarities
(©,
0).
Use of
batteries
•Do
not
mix
old
and
new
batteries,
or
batteries of different
types
(manganese and
alkaline,
etc.).
•Never
subject
batteries to
excessive heat
or flame;
do
not
attempt
to
disassemble them;
and be
sure they are
not
short-circuited.
•
If
the
remote
control
is
not
to
be used
for
a long period
of
time,
remove
the batteries
and
store
them
in
a
cool,
dark
place.
•
Do
not
attempt
to
recharge
alkaline or
manganese
batteries.
•
Do
not
use rechargeable
type
batteries.
Battery
life
The
battery
life
is
about
one
year.
The
batteries
should be replaced
if
commands
from
the
remote
control transmitter
do
not
operate
the
unit
even
when
the transmitter
is
held close
to
the
front
panel.
Correct
method
of use
Remote
control
sensor
IPs-!!
Transmission
window
Operations
notes
About 7 meters
in
front of
the
signal
sensor (The
actual
range
will
depend
on
the
angle
at
which
the
remote
control
is
used.)
•Aim
the
remote
control's
transmission
window
toward
the
unit's
sensor.
Avoid
any
obstacles.
•
Be
sure
the transmission
window and
the
unit's
sensor are
free
from
dust.
Excessive dust might
affect
its
performance.
•The
operation
may
not
be
correct
if
direct
sunlight or
other strong
light
source
strikes
the
receiving
sensor
of
this
unit.
If
there
is
a
problem, place the
unit
away
from the
light
source.
•If this
system
is
installed
in
a
rack
with
glass doors, the glass doors'
thickness or
color
might
make
it
necessary
to
use
the
remote
control
a shorter distance from the system.
•Never
place
heavy
items.
•Do
not
disassemble
or
reconstruct.
•Do
not
spill
water or
other
liquids.
Advertisement
Table of Contents
