Page 1
HCD-VP800AV SERVICE MANUAL E Model Tourist Model Ver 1.4 2003.12 • HCD-VP800AV is the tuner, deck, CD and amplifier section in MHC- VP800AV. Model Name Using Similar Mechanism HCD-VP700 CD Mechanism Type CDM58E-30BD61A Section Base Unit Name BU-30BD61A Optical Pick-up Name A-MAX.3...
Page 2
Laser Semiconductor laser LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE (λ=660 nm) COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS Frequency response 2 Hz – 20 kHz (±0.5 dB) APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS Signal-to-noise ratio More than 90 dB PUBLISHED BY SONY.
HCD-VP800AV SECTION 1 This section is extracted from instruction manual. GENERAL Parts Identification The items are arranged in alphabetical order. Main unit eaesedefegeh rgrfrdrs 2CH/MULTI rs (27) FM MODE eh (20) BUTTON DESCRIPTIONS CD e; (9, 12–15, 22, 23) GAME wg (31)
HCD-VP800AV Setting the time Turn on the system. Press CLOCK/TIMER SET. When you set the time for the first time, proceed to step 5. Press . or > repeatedly to select “CLOCK SET”. Press ENTER. Press . or > repeatedly to set the hour.
HCD-VP800AV SECTION 2 DISASSEMBLY • Abbreviation • The equipment can be removed using the following procedure. : Singapre model : Malaysia model Case (Top) Loading Panel Front Panel Section : Thai model Tape Mechanism Deck LEAF SW board, Head (A) board,...
Page 7
HCD-VP800AV 2-2. LOADING PANEL 4 pull-out the disc tray. CD mechanism deck (CDM58) 1 turn the pulley to the direction of arrow. loading panel front panel side pulley 2 pull-out the disc tray. 2-3. FRONT PANEL SECTION, CHASSIS SECTION, CD MECHANISM DECK (CDM58) qd CD mechanism deck (CDM58) 0 two screws (+BVTP 3 ×...
Page 8
HCD-VP800AV 2-4. TAPE MECHANISM DECK (TCM-230AWR41/MWR41) 1 four screws (+BVTP 2.6 × 8) 2 tape mechanism deck (TCM-230AWR41/MWR41) 2-5. CD PANEL BOARD, PANEL BOARD, OPT IN BOARD 1 five screws (+BVTP 2.6 × 8) two claws qf flat type wire (CN108)
Page 9
HCD-VP800AV 2-6. ESCUTCHEON PAD (WITH TOUCH PAD) 1 button (edit) 6 two screws (TPG +P 2 × 8) 8 three screws 3 two screws (+BVTP 2.6 × 8) (+BVTP 2.6 × 8) 9 button (DSP) 2 two screws (+BVTP 2.6 × 8) 5 two screws (TPG +P 2 ×...
Page 10
HCD-VP800AV 2-8. TRANS BOARD, MAIN BOARD 4 two screws 8 two screws 6 TRANS board (+BVTP 3 × 8) (+BVTT 4 × 8) 5 two screws 7 two screws (+BVTT 4 × 8) (+BVTT 3 × 8) 1 connector (CN914) 0 t wo screws (+BVTP 3 ×...
Page 11
HCD-VP800AV 2-10. LEAF SW BOARD, HEAD (A) BOARD, HEAD (B) BOARD (TCM-230AWR41/MWR41) Note: This illustration is for TCM-230MWR, but in case of TCM-230AWR, you can remove them in the same way. 1 five claws 2 LEAF SW board 3 remove the four solderings.
Page 12
HCD-VP800AV 2-12. BASE UNIT, BD BOARD 1 Pulley(B)(BU-30), chucking 2 Two Screws (+PTPWH M2.6) 3 Lever (lifter) 5 Screw (+PTPWH M2.6) 6 Holder assy 4 Turn the pulley to the direction of arrow. Spring (insulator), coil pulley Base unit qh Two insulators...
HCD-VP800AV SECTION 3 TEST MODE [Cold Reset] 3. Cursor segment flash on the FL display tube. The input • The cold reset clears all data including preset data stored in the FUNCTION is changed to GAME. RAM to initial conditions. Execute this mode when returning the set to the customer.
Page 14
HCD-VP800AV [CD Ship Mode (No Memory Clear)] • This mode moves the position to the position durable to vibra- tion Use this mode when returning the set to the customer after repair. Procedure: 1. Press `/1 button to turn the set ON.
Page 15
HCD-VP800AV [VCD COLOR SYSTEM MODE] [VIDEO BOARD] (SIDE A) • This mode is used for changing the COLOR SYSTEM of the VCD. Procedure: 1 2 3 J302 1. Set the standby mode. J301 2-1.Press the two buttons `/1 and > simultaneously to set the COLOR SYSTEM of the VCD to AUTO.
HCD-VP800AV SECTION 4 SECTION 5 MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS Precaution DECK SECTION 0 dB=0.775 V 1. Clean the following parts with a denatured alcohol-moistened swab: 1. Demagnetize the record/playback head with a head record/playback heads pinch rollers demagnetizer. erase head rubber belts 2.
Page 17
HCD-VP800AV 2. Turn the adjustment screw and check output peaks. If the peaks DECK B Tape Speed Adjustment do not match for L-CH and R-CH, turn the adjustment screw Note: Start the Tape Speed adjustment as below after setting to the test so that outputs match within 1dB of peak.
Page 18
HCD-VP800AV DECK B REC Bias Adjustment 4. Mode: Record Procedure: INTRODUCTION MD/VIDEO (AUDIO) IN When set to the test mode performed in Tape Speed Adjustment, 315 Hz, 50 mV (–23.8 dB) AF OSC when the tape is rewound after recording, the “REC memory mode”...
Page 19
HCD-VP800AV FM Tuned Level Adjustment CD SECTION Note : FM RF SSG 1. CD Block is basically designed to operate without adjustment. 75 Ω coaxial Therefore, check each item in order given. 2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.
Page 20
HCD-VP800AV Note: Clear RF signal waveform means that the shape “◊” can be Adjustment Location : clearly distinguished at the center of the waveform. [ BD (CD) BOARD ] — SIDE B — RF signal waveform VOLT/DIV : 200mV TIME/DIV : 500ns level : 1.1 ±...
Page 21
HCD-VP800AV VIDEO SECTION Frequency Adjustment Connection: frequency counter VIDEO board (27 MHz) Procedure: 1. Connect the frequency counter to check point of the VIDEO board. 2. Turned power switch on. 3. Press the CD button to select the CD. 4. Adjust CT503 on the VIDEO board so that the frequency counter reading 27.0 MHz ±...
HCD-VP800AV SECTION 6 DIAGRAMS THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIA- GRAMS. (In addition to this, the necessary note is printed in each block.) Note on Schematic Diagram: Note on Printed Wiring Boards: • All capacitors are in µF unless otherwise noted. pF: µµF •...
HCD-VP800AV 6-1. CIRCUIT BOARD LOCATION • WAVEFORMS – BD BOARD – – MAIN BOARD – IC101 t; (RFAC) IC101 el (FE) IC401 qa (XC-OUT) T301 4 CD PLAY MODE CD PLAY MODE STOP MODE TAPE B REC MODE MOTOR board...
HCD-VP800AV 6-2. BLOCK DIAGRAMS – TUNER/CD SECTION – AM/FM IF MPX IC11 • RCH is omitted LPF11 • Signal Path RF IF BUFFER L-CH ANT IN IF OUT FM IF L OUT : FM FM 75Ω OSC OUT MAIN R OUT...
Page 25
HCD-VP800AV – MAIN SECTION – IC1220 J601 RV1202 L REC OUT ECHO ECHO IC607(1/2) IC1001 LEVEV IC1201(1/2) RY1082 TM1001 SOUND PROCESSOR R-CH J1201 J1202 CENTER COUT SPEAKR MD VIDEO MIC1 MIC2 MAC IN Q610 L IN1 TUNER/CD MUTE RV1201 IC1201(2/2)
Page 26
HCD-VP800AV – VIDEO SECTION – IC501 IC505 (1/2) MPEG VIDEO/AUDIO DEC BUFFER VIDEO SIGNAL PROC IC303 IC304 Y AMP ADATA CD-DATA VIDEO MIX BUFFER TUNER/CD Y OUT L.P.F BCLK CD-BCK SECTION C OUT VOUT Y IN Y OUT1 (Page 24)
HCD-VP800AV 6-5. SCHEMATIC DIAGRAM – BD SECTION – • See page 23 for Waveforms. • See page 52 for IC Pin Function. • See page 60 for IC Block Diagrams. (RFAC) E-F BALANCE 0.47 IC B/D (TE) TP18 (SE) (FE) (DVC) +3.3V...
HCD-VP800AV 6-12. SCHEMATIC DIAGRAM – DSP (1/2) SECTION – • See page 62 for IC Block Diagrams. • See page 56 for IC Pin Function. DSP BOARD (1/2) IC605 0µH...
HCD-VP800AV 6-28. SCHEMATIC DIAGRAM – VIDEO (3/3) SECTION – • See page 23 for Waveforms. • See page 63 for IC Block Daiagrams. IC B/D IC B/D IC B/D IC504 TC74V HCU 04 FT(EL)
HCD-VP800AV 6-31. IC PIN FUNCTION DESCRINTION Pin No. Pin Name Discription • IC101 CXD3068Q (DIGITAL SIGNAL PROCESSOR) (BD Board ) Tracking error signal input Pin No. Pin Name Discription Center servo analog input DVDD0 Digital power supply RFDC RF signal input...
Page 53
HCD-VP800AV • IC401 MASTER CONTROL (M30622MGA-A36FP) (MAIN Board (2/3)) Pin No. Pin Name Discription AMP - DATA Amp data signal output AMP - CLK Amp clock signal output AMP - LAT Amp latch signal output SIRCS Remote commander signal input...
Page 54
HCD-VP800AV Discription Pin No. Pin Name NO - USE Not used B TRG B deck trigger control signal output AMS - IN AMS signal input CAPM - H/L Capstan moter highi/low speed control signal output CAPM - CONT Capstan moter REV/FWD/STOP control signal output...
Page 55
HCD-VP800AV • IC1101 DISPLAY CONTROL (MB90M407APF-G-105-BND) (PANEL Board (1/2)) Discription Pin No. Pin Name FIPLED16 Grid drive signal output to the fluorescent indicator 2 - 5 FIP17 - 20 Grid drive signal output to the fluorescent indicator 6 - 10...
Page 56
HCD-VP800AV • IC601 DECODER (CXD9617R) (DSP Board (1/2)) Pin No. Pin Name Discription — Ground XRST Reset signal input EXTIN Not used (connected to ground) Not used (connected to ground) VDDI Power supply Not used (connected to ground) PLOCK Internal PLL lock signal output (Not used) —...
Page 57
HCD-VP800AV Pin No. Pin Name Discription MOD0 Operation mode signal input (L : single chip mode, H : use prohibited) EXLOCK Lock signal input VDDI Power supply — Ground 62, 63 A17, A16 Not used (open) 64 - 66 A15 - A13...
Page 58
HCD-VP800AV • IC502 M30622MGA-A59FP (CD MECHANISM CONTROLLER) (VIDEO BOARD) Discription Pin No. Pin Name SENSE Internal state (SENSE) monitor input SENSE CLK Serial data reading clock output RESOLUTION Y resolution output CROMA LEVEL Chroma level controll signal output DSP CLK...
Page 59
HCD-VP800AV Pin No. Pin Name Discription INSW Not used (connected to +5V) OUTSW Not used (open) MODEL 1 Not used (open) MODEL 2 Not used (open) TBLL Not used (open) TBLR Not used (open) ENC 1 Not used (open) ENC 2...
HCD-VP800AV SECTION 7 EXPLODED VIEWS NOTE: • -XX, -X mean standardized parts, so they may • Hardware (# mark) list and accessories and The components identified by have some differences from the original one. packing materials are given in the last of this mark 0 or dotted line with mark •...
HCD-VP800AV 7-3. CHASSIS SECTION not supplied not supplied not supplied (MY, SP, JE) T911 not supplied (TH) not supplied The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
HCD-VP800AV 7-4. TAPE MECHANISM DECK SECTION-1 (TCM-230MWR41) • The thing that a part A curves is TCM-230MWR41. Note: Two different types of tape mechanism are used depending on models. They maintain compatibility as an entire mechanism even though there are some different parts are used.
HCD-VP800AV 7-5. TAPE MECHANISM DECK SECTION-2 (TCM-230AWR41) • The thing that a part A doesn’t curve is TCM-230AWR41. Note: Two different types of tape mechanism are used depending on models. They maintain compatibility as an entire mechanism even though there are some different parts are used.
HCD-VP800AV SECTION 8 ELECTRICAL PARTS LIST NOTE: Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks • Due to standardization, replacements in the • COILS uH: µH parts list may be different from the parts The components identified by...
Page 72
HCD-VP800AV Ver 1.2 2002.03 CD PANEL CD SENSOR DRIVER Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R167 1-216-864-11 METAL CHIP 1/16W R1151 1-249-422-11 CARBON 2.7K 1/4W F R168 1-216-864-11 METAL CHIP 1/16W R1152 1-249-424-11 CARBON 3.9K...
Page 90
HCD-VP800AV REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2001.