http://www.xiaoyu163.com PROTECTION OF EYES FROM LASER BEAM DURING SERVICING -1/1 3 7 63 1515 0 This set employs laser. Therefore, be sure to follow carefully the CAUTION instructions below when servicing. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
http://www.xiaoyu163.com SPECIFICATIONS 3 7 63 1515 0 Discs suppor CD/CD-R/CD-RW for digital audio Frequency response 2 Hz to 20 kHz Playback signal-to-noise ratio 105 dB Playback total harmonic distortion 0.005% / —88 dB Digital input sampling frequency range 32 to 96 kHz (sampling rate conversion) Digital input format...
http://www.xiaoyu163.com DISASSEMBLY INSTRUCTIONS - 1/2 3 7 63 1515 0 1. Case Top Removal 4) Release CN803 from CD-P C.B and release CN803, CN804 1) Release 6 screws. from POWER C.B, AND release CN805, CN806 from I/O 2) Lift the Case Top with holding the back of it and remove it. C.B.
http://www.xiaoyu163.com DISASSEMBLY INSTRUCTIONS - 2/2 3 7 63 1515 0 5. CD-P Mechanism Removal (See Fig. 5) 7. Power C.B Removal (See Fig. 7) 1) Release CN602, CN606, CN901, PIN603 from CD-P C.B. 1) Release connector CN301. 2) Release 4 screws (C), and then release CD-P Mechanism in 2) Release 4 screws (E), and then release POWER C.B in the the direction of the arrow.
http://www.xiaoyu163.com TRANSISTOR ILLUSTRATION 3 7 63 1515 0 E C B E C B E C B KRA103M KTC3198 KSB1151 2SA1037 KRA105M DTA144EK KRC105M DTC144EK KTD1302 KTD1304S L 13942296513 u163 -11- http://www.xiaoyu163.com...
http://www.xiaoyu163.com SCHEMATIC DIAGRAM - 9/10 (FRONT SECTION) 3 7 6 3 1 5 1 5 0 FRONT(L) C.B BJ-820GNK LCD DISPLAY TRACK TOTAL REMAIN TIME TRACK TOTAL REMAIN TIME SCAN RPM6938-V4 RANDOM PROG REPEAT 1 A-B ALL OVER OVER RANDOM PROG REPEAT 1 A-B ALL X2 X4 REMOTE SENSOR...
Page 52
http://www.xiaoyu163.com IC BLOCK DIAGRAM - 6/7 3 7 63 1515 0 IC, KA78R12 OVERVOLTAGE THERMAL SHUTDOWN PROTECTION BANDGAP REFERENCE SOA PROTECT I ON OUTPUT HIGH / LOW ON / OFF Vdis SHORTCIRCUIT 1.4V PROTECTION L 13942296513 IC, LB11995H V CC 2 V CC 1 U IN 1 U IN 2...
http://www.xiaoyu163.com IC DESCRIPTION - 1/2 (AK4393VF-E2) -1/1 3 7 63 1515 0 Pin No. Pin Name Description DVSS – Digital Ground. Digital ground is 0 V. DVDD – Digital Supply. 3.3 V or 5.0 V nominal. MCLK Master Clock Input. Power-down and Reset.
http://www.xiaoyu163.com IC DESCRIPTION - 2/2 (CXA2581N) 1/1 3 7 63 1515 0 Pin No. Pin Name Description APC amplifier output. APC amplifier input. EQ_IN RFAC system VCA block and EQ block input. AC_SUM RFAC system RF SUM output. A signal input. B signal input.
http://www.xiaoyu163.com MECHANICAL MAIN PARTS LIST - 1/1 3 7 63 1515 0 REF. NO PART NO. KANRI DESCRIPTION S5-80R-T01-4A0 DOOR CDP S5-80R-T01-5A0 DOOR CDR 256-1 ————— DECK ASSY,AUDIO AADR600/640N E S6-10S-019-2E0 FOOT ADR-640 ————— CHASSIS MAIN S7-90R-P01-8A0 WINDOW FL S8-06R-001-0A0 DECO PANEL S7-20R-F13-2A0 PANEL FRONT...
http://www.xiaoyu163.com COLOR NAME TABLE 3 7 63 1515 0 COLOR NAME TABLE Basic color symbol Color Basic color symbol Color Basic color symbol Color Black Cream Orange Green Gray Blue Transparent Blue Gold Pink Silver Titan Silver Brown Violet White Transparent White Yellow Transparent Yellow...
http://www.xiaoyu163.com TROUBLESHOOTING - 1/26 3 7 63 1515 0 1. POWER CIRCUIT(SMPS) 1) NO 5V(-COM, FRONT) No 5V Replace the F901. Is the F901 normal? (Use standard fuse) Is the BD901 normal? Replace the BD901. Is the R901 normal? Replace the R901. Is VCC(=13~18V) supplied to the Is the D902 normal? IC901 pin5?
Page 65
http://www.xiaoyu163.com TROUBLESHOOTING - 2/26 3 7 63 1515 0 2) When +12V(I/O) doesn’t appear, 3) When -12V(I/O) doesn’t appear, When +12V doesn't appear, When -12V doesn't appear, Check and replace the Is the D910 normal? Is the D908 normal? Check and replace D908. D910.
Page 71
http://www.xiaoyu163.com TROUBLESHOOTING - 8/26 3 7 63 1515 0 Reset or Power Check. Is the Pin 1, 3 of PN105 5V? Check the PN105. Is the Pin 5 of PN105 12V? Check the SMPS board. Does the pin1 Check the IC101(RESET IC). of IC101 change 0V to 5V at the power Check the IC701(HD64F3062), supply initial input mode?
Page 72
http://www.xiaoyu163.com TROUBLESHOOTING - 9/26 3 7 63 1515 0 System Check. Load tray without inserting disc. Does Tray operate normally? Go to "Tray operating is abnormal" Does Pick-up move to inside? Go to "Sled operating is abnormal" Go to "Spindle opreating is Does Spindle Motor rotate in a moment? abnormal"...
Page 73
http://www.xiaoyu163.com TROUBLESHOOTING - 10/26 3 7 63 1515 0 Tray operating is abnormal.(CDP) (Tray open/close doesn’t work) Check the connection of IC301 pin 16. Replace the IC301(M56788FP). Is threre Tray control signal intput? Check the communication line between (IC501 pin23) IC301 and IC501(MICOM).
Page 74
http://www.xiaoyu163.com TROUBLESHOOTING - 11/26 3 7 63 1515 0 Tray operating is abnormal. (Tray open/close doesn’t work) Check the connection of IC409 pin 12. Replace the IC409(M62352GP). Is threre Tray control signal intput? Check the communication line between (IC501 pin25) IC409 and IC701(MICOM).
Page 75
http://www.xiaoyu163.com TROUBLESHOOTING - 12/26 3 7 63 1515 0 Sled operating is abnormal. Is there Check the connection of IC701 Sled control signal output? Replace the IC701(MICOM) pin 85 (IC701 pin 85) Is there Check the connection of IC502 Sled drive voltage input? pin 17.
Page 76
http://www.xiaoyu163.com TROUBLESHOOTING - 13/26 3 7 63 1515 0 Spindle operating is abnormal. Is there Spindle Check the connection of IC201 pin2. Is there DMO signal input? control signal input? (IC509 pin5) Replace the IC201(OTI-9790) (IC510 pin 22) Is there Spindle Replace the IC509(NJM3404AV).
Page 77
http://www.xiaoyu163.com TROUBLESHOOTING - 14/26 3 7 63 1515 0 Focus Actuator operating is abnormal Check the connection of IC201 pin207. Is there Check the communication line between Focus Search control signal IC201 and IC701 input? (IC501 pin 3) Replace the IC201(OTI-9790) Check the connection of IC701 Is there Focus Search Is Act_Mute signal L ?
Page 78
http://www.xiaoyu163.com TROUBLESHOOTING - 15/26 3 7 63 1515 0 Spindle control is abnormal 2 (CD-AUDIO Disc) Is there RRF signal input? Go to RF output is abnormal (IC413 pin 3) Is there RFDC signal input? Replace the IC413(EL2245CS). (IC401 pin 85) Does Tracking Go to Track servo is unstable Servo operate normally?
Page 79
http://www.xiaoyu163.com TROUBLESHOOTING - 16/26 3 7 63 1515 0 Disc recognition is abnormal Is there Is there CDR/RW signal input RECD1, RECD2 signal Go to RF output is abnormal normally?(IC601 pin 33) output normally? (IC401 pin 80,81) Go to Track Servo is unstable Replace IC701 (MICOM) RF output is abnormal Is there...
Page 80
http://www.xiaoyu163.com TROUBLESHOOTING - 17/26 3 7 63 1515 0 Focus Servo is unstable Is FE signal output normal in Focusing Check the IC401(CXA2551R). Up/Down? (IC401 pin 56) Go to RF output is abnormal Is FAO signal output normal in Focusing Replace the IC201(OTI-9790).
Page 81
http://www.xiaoyu163.com TROUBLESHOOTING - 18/26 3 7 63 1515 0 Laser is unstable Execute B.Calibration Data of How to use Test Tool(Dragon) Is EEPROM Data valid? Execute C.LD Inspection of Execute C.LD Power setup of How to use Test Tool(Dragon) How to use Test Tool(Dragon) Normal OFF LEVEL NG? L 13942296513...
Page 82
http://www.xiaoyu163.com TROUBLESHOOTING - 19/26 3 7 63 1515 0 LD CHECK (Not Read) Execute E.LD On of How to use Test Tool(Dragon) : VRDC Loop [Read Mode] Check the connection of IC601 pin 20. CN401 Pin 32(ENBL)=H? Check and replace the IC601(CPLD). IC401 Check the connection of IC409 pin 18.
Page 83
http://www.xiaoyu163.com TROUBLESHOOTING - 20/26 3 7 63 1515 0 LD CHECK (Not Recored) Execute E.LD On of How to use Check the connection of IC601 pin 20. Test Tool(Dragon) : Check and replace the IC601(CPLD). VWDC-1 Loop Check the connection of IC409 pin 18,29 and 34.
Page 84
http://www.xiaoyu163.com TROUBLESHOOTING - 21/26 3 7 63 1515 0 Execute E.LD On of How to use Test Tool(Dragon) : VWDC-2 Check the connection of IC601 pin 21 CN401 Pin 30(ODON)=H? and 30. Check and replace the IC601(CPLD). Check the connection of IC601 pin 18 and 34.
Page 85
http://www.xiaoyu163.com TROUBLESHOOTING - 22/26 3 7 63 1515 0 In case of writing fail. Nomal Case Check the Media CD-R Check disc Label. or CD-RW? Romove the Dust, Fingerprint Dose the disc have and if the disc has long width any Dust, Scratch, Fingerprint...? Scratch, change it.
Page 86
http://www.xiaoyu163.com TROUBLESHOOTING - 23/26 3 7 63 1515 0 Writing Part Check. Refer Laser is abnormal . Load tray with CD-R/RW Disc. Start Recording or dubbing. Does the unit become stand-by mode to record/dubbing? Check the communication Iines between IC701 and IC201. Check and replace the 701.
Page 87
http://www.xiaoyu163.com TROUBLESHOOTING - 24/26 3 7 63 1515 0 ALPC Logic circuit check Execute E. LD On of How to use Test Tool(Dragon) : CD-R Recording Mode Check the connection of IC701 pin 20. IC601 Pin 33(CDR/RW)= H ? Check and replace the IC701. Check the connection of IC701 pin 7.
Page 88
http://www.xiaoyu163.com TROUBLESHOOTING - 25/26 3 7 63 1515 0 Execute E. LD On of How to use Test Tool(Dragon) : CD-RW Recording Mode the connection of IC701 pin 20. Check IC601 Pin 33(CDR/RW)= L ? Check and replace the IC701. Check the connection of IC701 pin 7.
http://www.xiaoyu163.com TROUBLESHOOTING - 26/26 3 7 63 1515 0 BETA Measurement circuit ceck After inserting Test Disc(TCD-784), start playing. Check the connection of IC401 pin 86. IC401 Pin 86(RRF):3+/-1.0V? Check and replace the IC401 (CXA2551R). Check the connection of IC407. RRFIN:2+/0.7V? Check and replace the IC407.
Page 90
http://www.xiaoyu163.com 3 7 63 1515 0 L 13942296513 u163 2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110-8710, JAPAN TEL:03 (3827) 3111 920074 Printed in Singapore http://www.xiaoyu163.com...